HGTG11N120CN FAIRCHILD
Document overview
- PDF pages: 7
Technical content
Page 1
Data Sheet
43A, 1200V, NPT Series N-Channel IGBT
The HGTG11N120CN, HGTP11N120CN, and HGT1S11N120CNS are Non-Punch Through (NPT) IGBT designs. They are new members of the MOS gated high voltage switching IGBT family. IGBTs combine the best features of MOSFETs and bipolar transistors. This device has the high input impedance of a MOSFET and the low on- state conduction loss of a bipolar transistor.
The IGBT is ideal for many high voltage switching applications operating at moderate frequencies where low conduction losses are essential, such as: AC and DC motor controls, power supplies and drivers for solenoids, relays and contactors.
Formerly Developmental Type TA49291.
Ordering Information
| PART NUMBER | PACKAGE | BRAND |
|---|---|---|
| HGTG11N120CN | TO-247 | G11N120CN |
| HGTP11N120CN | TO-220AB | 11N120CN |
| HGT1S11N120CNS | TO-263AB | 11N120CN |
NOTE: When ordering, use the entire part number. Add the suffix 9A to obtain the TO-263AB variant in Tape and Reel, i.e., HGT1S11N120CNS9A.
Symbol
C
G
E
HGTG11N120CN, HGTP11N120CN,
HGT1S11N120CNS
December 2001
Features
- 43A, 1200V, TC = 25oC
- 1200V Switching SOA Capability
- Typical Fall Time. . . . . . . . . . . . . . . . 340ns at TJ = 150oC
- Short Circuit Rating
- Low Conduction Loss
- Avalanche Rated
- Thermal Impedance SPICE Model Temperature Compensating SABER™ Model www.fairchildsemi.com
- Related Literature - TB334 “Guidelines for Soldering Surface Mount Components to PC Boards”
Packaging
JEDEC STYLE TO-247
E

JEDEC TO-220AB (ALTERNATE VERSION)

COLLECTOR
E
(FLANGE)
C
JEDEC TO-263AB
COLLECTOR
(FLANGE)
G
E
FAIRCHILD SEMICONDUCTOR IGBT PRODUCT IS COVERED BY ONE OR MORE OF THE FOLLOWING U.S. PATENTS
4,364,073
4,417,385
4,430,792
4,443,931
4,466,176
4,516,143
4,532,534
4,587,713
4,598,461
4,605,948
4,620,211
4,631,564
4,639,754
4,639,762
4,641,162
4,644,637
4,682,195
4,684,413
4,694,313
4,717,679
4,743,952
4,783,690
4,794,432
4,801,986
4,803,533
4,809,045
4,809,047
4,810,665
4,823,176
4,837,606
4,860,080
4,883,767
4,888,627
4,890,143
4,901,127
4,904,609
4,933,740
4,963,951
4,969,027
Page 2
Absolute Maximum Ratings TC = 25oC, Unless Otherwise Specified
HGTG11N120CN
HGTP11N120CN
HGT1S11N120CNS
UNITS
1200
V
Collector to Emitter Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BVCES Collector Current Continuous At TC = 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IC25
43
A
At TC = 110oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IC110
22
A
Collector Current Pulsed (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ICM
80
A
±20
V
Gate to Emitter Voltage Continuous. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VGES
±30
V
Gate to Emitter Voltage Pulsed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VGEM Switching Safe Operating Area at TJ = 150oC (Figure 2) . . . . . . . . . . . . . . . . . . . . . . . SSOA
55A at 1200V
Power Dissipation Total at TC = 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PD
298
W
Power Dissipation Derating TC > 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
W/oC
2.38 80
mJ
Forward Voltage Avalanche Energy (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EAV
oC
Operating and Storage Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . TJ, TSTG
-55 to 150
Maximum Lead Temperature for Soldering
oC
300
Leads at 0.063in (1.6mm) from case for 10s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TL
oC
260
Package Body for 10s, see Tech brief 334. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tpkg Short Circuit Withstand Time (Note 3) at VGE = 15V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . tSC
8
µs
Short Circuit Withstand Time (Note 3) at VGE = 12V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . tSC
15
µs
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES: 1. Pulse width limited by maximum junction temperature. 2. ICE = 20A, L = 400µH, TJ = 25oC. 3. VCE(PK) = 840V, TJ = 125oC, RG = 10Ω.
Electrical Specifications TC = 25oC, Unless Otherwise Specified
| PARAMETER | SYMBOL | TEST CONDITIONS | MIN | TYP | MAX | UNITS | |
|---|---|---|---|---|---|---|---|
| Collector to Emitter Breakdown Voltage | BVCES | IC = 250µA, VGE = 0V | 1200 | - | - | V | |
| Emitter to Collector Breakdown Voltage | BVECS | IC = 10mA, VGE = 0V | 15 | - | - | V | |
| Collector to Emitter Leakage Current | ICES | VCE = 1200V | TC = 25oC | - | - | 250 | µA |
| TC = 125oC | - | 250 | - | µA | |||
| TC = 150oC | - | - | 3 | mA | |||
| Collector to Emitter Saturation Voltage | VCE(SAT) | IC = 11A, VGE = 15V | TC = 25oC | - | 2.1 | 2.4 | V |
| TC = 150oC | - | 2.8 | 3.5 | V | |||
| Gate to Emitter Threshold Voltage | VGE(TH) | IC = 90µA, VCE = VGE | 6.0 | 6.8 | - | V | |
| Gate to Emitter Leakage Current | IGES | VGE = ±20V | - | - | ±250 | nA | |
| Switching SOA | SSOA | TJ = 150oC, RG = 10Ω, VGE = 15V, L = 400µH, VCE(PK) = 1200V | 55 | - | - | A | |
| Gate to Emitter Plateau Voltage | VGEP | IC = 11A, VCE = 600V | - | 10.4 | - | V | |
| On-State Gate Charge | QG(ON) | IC = 11A, VCE = 600V | VGE = 15V | - | 100 | 120 | nC |
| VGE = 20V | - | 130 | 150 | nC | |||
Page 3
Electrical Specifications TC = 25oC, Unless Otherwise Specified (Continued)
| PARAMETER | SYMBOL | TEST CONDITIONS | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|---|
| Current Turn-On Delay Time | td(ON)I | IGBT and Diode at TJ = 25oC ICE = 11A VCE = 960V VGE = 15V RG = 10Ω L = 2mH Test Circuit (Figure 18) | - | 23 | 26 | ns |
| Current Rise Time | trI | - | 12 | 16 | ns | |
| Current Turn-Off Delay Time | td(OFF)I | - | 180 | 240 | ns | |
| Current Fall Time | tfI | - | 190 | 230 | ns | |
| Turn-On Energy (Note 4) | EON1 | - | 0.4 | 0.5 | mJ | |
| Turn-On Energy (Note 4) | EON2 | - | 0.95 | 1.3 | mJ | |
| Turn-Off Energy (Note 5) | EOFF | - | 1.3 | 1.6 | mJ | |
| Current Turn-On Delay Time | td(ON)I | IGBT and Diode at TJ = 150oC ICE = 11A VCE = 960V VGE = 15V RG = 10Ω L = 2mH Test Circuit (Figure 18) | - | 21 | 24 | ns |
| Current Rise Time | trI | - | 12 | 16 | ns | |
| Current Turn-Off Delay Time | td(OFF)I | - | 210 | 280 | ns | |
| Current Fall Time | tfI | - | 340 | 400 | ns | |
| Turn-On Energy (Note 4) | EON1 | - | 0.45 | 0.6 | mJ | |
| Turn-On Energy (Note 4) | EON2 | - | 1.9 | 2.5 | mJ | |
| Turn-Off Energy (Note 5) | EOFF | - | 2.1 | 2.5 | mJ | |
| Thermal Resistance Junction To Case | RθJC | - | - | 0.42 | oC/W |
NOTES: 4. Values for two Turn-On loss conditions are shown for the convenience of the circuit designer. EON1 is the turn-on loss of the IGBT only. EON2 is the turn-on loss when a typical diode is used in the test circuit and the diode is at the same TJ as the IGBT. The diode type is specified in Figure 18. 5. Turn-Off Energy Loss (EOFF) is defined as the integral of the instantaneous power loss starting at the trailing edge of the input pulse and ending at the point where the collector current equals zero (ICE = 0A). All devices were tested per JEDEC Standard No. 24-1 Method for Measurement of Power Device Turn-Off Switching Loss. This test method produces the true total Turn-Off Energy Loss.
Typical Performance Curves Unless Otherwise Specified

TC, CASE TEMPERATURE (oC)
FIGURE 1. DC COLLECTOR CURRENT vs CASE
TEMPERATURE

VCE, COLLECTOR TO EMITTER VOLTAGE (V)
FIGURE 2. MINIMUM SWITCHING SAFE OPERATING AREA
Page 4
Typical Performance Curves Unless Otherwise Specified (Continued)


ICE, COLLECTOR TO EMITTER CURRENT (A)
VGE, GATE TO EMITTER VOLTAGE (V)
FIGURE 3. OPERATING FREQUENCY vs COLLECTOR TO
FIGURE 4. SHORT CIRCUIT WITHSTAND TIME
EMITTER CURRENT


VCE, COLLECTOR TO EMITTER VOLTAGE (V)
VCE, COLLECTOR TO EMITTER VOLTAGE (V)
FIGURE 6. COLLECTOR TO EMITTER ON-STATE VOLTAGE
FIGURE 5. COLLECTOR TO EMITTER ON-STATE VOLTAGE


0
5 10
20
15
ICE, COLLECTOR TO EMITTER CURRENT (A)
ICE, COLLECTOR TO EMITTER CURRENT (A)
FIGURE 8. TURN-OFF ENERGY LOSS vs COLLECTOR TO
FIGURE 7. TURN-ON ENERGY LOSS vs COLLECTOR TO
EMITTER CURRENT
EMITTER CURRENT
Page 5
Typical Performance Curves Unless Otherwise Specified (Continued)


10
0
15
20
5
ICE, COLLECTOR TO EMITTER CURRENT (A)
ICE, COLLECTOR TO EMITTER CURRENT (A)
FIGURE 10. TURN-ON RISE TIME vs COLLECTOR TO
FIGURE 9. TURN-ON DELAY TIME vs COLLECTOR TO
EMITTER CURRENT
EMITTER CURRENT


ICE, COLLECTOR TO EMITTER CURRENT (A)
ICE, COLLECTOR TO EMITTER CURRENT (A)
FIGURE 12. FALL vs COLLECTOR TO EMITTER CURRENT
FIGURE 11. TURN-OFF DELAY TIME vs COLLECTOR TO
EMITTER CURRENT


VGE, GATE TO EMITTER VOLTAGE (V)
QG, GATE CHARGE (nC)
FIGURE 13. TRANSFER CHARACTERISTIC
FIGURE 14. GATE CHARGE WAVEFORMS
Page 6
Typical Performance Curves Unless Otherwise Specified (Continued)

VCE, COLLECTOR TO EMITTER VOLTAGE (V)
FIGURE 15. CAPACITANCE vs COLLECTOR TO EMITTER
VOLTAGE

VCE, COLLECTOR TO EMITTER VOLTAGE (V)
FIGURE 16. COLLECTOR TO EMITTER ON-STATE VOLTAGE

t1, RECTANGULAR PULSE DURATION (s)
FIGURE 17. NORMALIZED TRANSIENT THERMAL RESPONSE, JUNCTION TO CASE
Test Circuit and Waveforms


VDD = 960V
FIGURE 18. INDUCTIVE SWITCHING TEST CIRCUIT
FIGURE 19. SWITCHING TEST WAVEFORMS
Page 7
Handling Precautions for IGBTs
Insulated Gate Bipolar Transistors are susceptible to gate-insulation damage by the electrostatic discharge of energy through the devices. When handling these devices, care should be exercised to assure that the static charge built in the handler’s body capacitance is not discharged through the device. With proper handling and application procedures, however, IGBTs are currently being extensively used in production by numerous equipment manufacturers in military, industrial and consumer applications, with virtually no damage problems due to electrostatic discharge. IGBTs can be handled safely if the following basic precautions are taken:
- Prior to assembly into a circuit, all leads should be kept shorted together either by the use of metal shorting springs or by the insertion into conductive material such as “ECCOSORBD™ LD26” or equivalent. 2. When devices are removed by hand from their carriers, the hand being used should be grounded by any suitable means - for example, with a metallic wristband. 3. Tips of soldering irons should be grounded. 4. Devices should never be inserted into or removed from circuits with power on. 5. Gate Voltage Rating - Never exceed the gate-voltage rating of VGEM. Exceeding the rated VGE can result in permanent damage to the oxide layer in the gate region. 6. Gate Termination - The gates of these devices are
essentially capacitors. Circuits that leave the gate open-circuited or floating should be avoided. These conditions can result in turn-on of the device due to voltage buildup on the input capacitor due to leakage currents or pickup. 7. Gate Protection - These devices do not have an internal monolithic Zener diode from gate to emitter. If gate protection is required an external Zener is recommended.
Operating Frequency Information
Operating frequency information for a typical device (Figure 3) is presented as a guide for estimating device performance for a specific application. Other typical frequency vs collector current (ICE) plots are possible using the information shown for a typical unit in Figures 5, 6, 7, 8, 9 and 11. The operating frequency plot (Figure 3) of a typical device shows fMAX1 or fMAX2; whichever is smaller at each point. The information is based on measurements of a typical device and is bounded by the maximum rated junction temperature.
fMAX1 is defined by fMAX1 = 0.05/(td(OFF)I+ td(ON)I). Deadtime (the denominator) has been arbitrarily held to 10% of the on-state time for a 50% duty factor. Other definitions are possible. td(OFF)I and td(ON)I are defined in Figure 19. Device turn-off delay can establish an additional frequency limiting condition for an application other than TJM. td(OFF)I is important when controlling output ripple under a lightly loaded condition.
fMAX2 is defined by fMAX2 = (PD - PC)/(EOFF + EON2). The allowable dissipation (PD) is defined by PD = (TJM - TC)/RθJC. The sum of device switching and conduction losses must not exceed PD. A 50% duty factor was used (Figure 3) and the conduction losses (PC) are approximated by PC = (VCE x ICE)/2. EON2 and EOFF are defined in the switching waveforms shown in Figure 19. EON2 is the integral of the instantaneous power loss (ICE x VCE) during turn-on and EOFF is the integral of the instantaneous power loss (ICE x VCE) during turn-off. All tail losses are included in the calculation for EOFF; i.e., the collector current equals zero (ICE = 0).