HEF4520B NEXPERIA

Document overview

  • PDF pages: 12

Technical content

Page 1

1. General description

The HEF4520B is a dual 4-bit internally synchronous binary counter with two clock inputs (nCP0 and nCP1), buffered outputs from all four bit positions (nQ0 to nQ3) and an asynchronous master reset input (nMR). The counter advances on either the LOW-to-HIGH transition of nCP0 if nCP1 is HIGH or the HIGH-to-LOW transition of nCP1 if nCP0 is LOW. Either nCP0 or nCP1 may be used as the clock input to the counter and the other clock input may be used as a clock enable input. A HIGH on nMR resets the counter (nQ0 to nQ3 = LOW) independent of nCP0 and nCP1. Inputs include clamp diodes. This enables the use of current limiting resistors to interface inputs to

voltages in excess of VDD.

2. Features and benefits

  • Tolerant of slow clock rise and fall times
  • Fully static operation
  • 5 V, 10 V, and 15 V parametric ratings
  • Wide supply voltage range from 3.0 V to 15.0 V
  • CMOS low power dissipation
  • High noise immunity
  • Standardized symmetrical output characteristics
  • Complies with JEDEC standard JESD 13-B
  • ESD protection:
  • HBM JESD22-A114F exceeds 2000 V
  • MM JESD22-A115-B exceeds 200 V
  • Specified from -40 °C to +85 °C

3. Ordering information

Table 1. Ordering information

Type number Package
Temperature range Name Description Version
HEF4520BT -40 °C to +85 °C SO16 plastic small outline package; 16 leads; body width 3.9 mm SOT109-1

Page 2

4. Functional diagram

PDF page 2 diagram

2 / 12

Page 3

5. Pinning information

5.1. Pinning

PDF page 3 diagram

5.2. Pin description

Table 2. Pin description

Symbol Pin Description
1CP0, 2CP0 1, 9 clock input (LOW-to-HIGH triggered)
1CP1, 2CP1 2, 10 clock input (HIGH-to-LOW triggered)
1Q0, 1Q1, 1Q2, 1Q3 3, 4, 5, 6 output
1MR, 2MR 7, 15 master reset input
V SS 8 ground supply voltage
2Q0, 2Q1, 2Q2, 2Q3 11, 12, 13, 14 output
V DD 16 supply voltage

6. Functional description

Table 3. Function table H = HIGH voltage level; L = LOW voltage level; X = don’t care; ↑ = positive-going transition; ↓ = negative-going transition.

nCP0 nCP1 nMR Mode
↑ H L counter advances
L ↓ L counter advances
↓ X L no change
X ↑ L no change
↑ L L no change
H ↓ L no change
X X H nQ0 to nQ3 = LOW

3 / 12

Page 4

7. Limiting values

Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to VSS = 0 V (ground).

Symbol Parameter Conditions Min Max Unit
V DD supply voltage -0.5 +18 V
I IK input clamping current V < -0.5 V or V > V + 0.5 V I I DD - ±10 mA
V I input voltage -0.5 V + 0.5 DD V
I OK output clamping current V < -0.5 V or V > V + 0.5 V O O DD - ±10 mA
I I/O input/output current - ±10 mA
I DD supply current - 50 mA
T stg storage temperature per output -65 +150 °C
T amb ambient temperature -40 +85 °C
P tot total power dissipation SO16 package - 500 mW
P power dissipation - 100 mW

8. Recommended operating conditions

Table 5. Recommended operating conditions

Symbol Parameter Conditions Min Typ Max Unit
V DD supply voltage 3 - 15 V
V I input voltage 0 - V DD V
T amb ambient temperature in free air -40 - +85 °C
Δt/ΔV input transition rise and fall rate V = 5 V DD - - 3.75 μs/V
V = 10 V DD - - 0.5 μs/V
V = 15 V DD - - 0.08 μs/V

9. Static characteristics

Table 6. Static characteristics VSS = 0 V; VI = VSS or VDD unless otherwise specified.

Symbol Parameter Conditions V DD T = -40 °C amb T = 25 °C amb T = 85 °C amb Unit
Min Max Min Max Min Max
V IH HIGH-level input voltage |I | < 1 μA O 5 V 3.5 - 3.5 - 3.5 - V
10 V 7.0 - 7.0 - 7.0 - V
15 V 11.0 - 11.0 - 11.0 - V
V IL LOW-level input voltage |I | < 1 μA O 5 V - 1.5 - 1.5 - 1.5 V
10 V - 3.0 - 3.0 - 3.0 V
15 V - 4.0 - 4.0 - 4.0 V
V OH HIGH-level output voltage |I | < 1 μA; O V = V or V I SS DD 5 V 4.95 - 4.95 - 4.95 - V
10 V 9.95 - 9.95 - 9.95 - V
15 V 14.95 - 14.95 - 14.95 - V
V OL LOW-level output voltage |I | < 1 μA; O V = V or V I SS DD 5 V - 0.05 - 0.05 - 0.05 V
10 V - 0.05 - 0.05 - 0.05 V
15 V - 0.05 - 0.05 - 0.05 V

4 / 12

Page 5

Symbol Parameter Conditions V DD T = -40 °C amb T = 25 °C amb T = 85 °C amb Unit
Min Max Min Max Min Max
I OH HIGH-level output current V = 2.5 V O 5 V - -1.7 - -1.4 - -1.1 mA
V = 4.6 V O 5 V - -0.52 - -0.44 - -0.36 mA
V = 9.5 V O 10 V - -1.3 - -1.1 - -0.9 mA
V = 13.5 V O 15 V - -3.6 - -3.0 - -2.4 mA
I OL LOW-level output current V = 0.4 V O 5 V 0.52 - 0.44 - 0.36 - mA
V = 0.5 V O 10 V 1.3 - 1.1 - 0.9 - mA
V = 1.5 V O 15 V 3.6 - 3.0 - 2.4 - mA
I I input leakage current V = 15 V DD 15 V - ±0.3 - ±0.3 - ±1.0 μA
I DD supply current I = 0 A; O V = V or V I SS DD 5 V - 20 - 20 - 150 μA
10 V - 40 - 40 - 300 μA
15 V - 80 - 80 - 600 μA
C I input capacitance - - - - 7.5 - - pF

10. Dynamic characteristics

Table 7. Dynamic characteristics VSS = 0 V; Tamb = 25 °C; unless otherwise specified. For test circuit see Fig. 6.

Symbol Parameter Conditions V DD Extrapolation formula [1] Min Typ Max Unit
t PHL HIGH to LOW propagation delay nCP0, nCP1 to nQn; see Fig. 5 5 V 83 ns + (0.55 ns/pF)C L - 110 220 ns
10 V 39 ns + (0.23 ns/pF)C L - 50 100 ns
15 V 32 ns + (0.16 ns/pF)C L - 40 80 ns
nMR to nQn; see Fig. 5 5 V 48 ns + (0.55 ns/pF)C L - 75 150 ns
10 V 24 ns + (0.23 ns/pF)C L - 35 70 ns
15 V 17 ns + (0.16 ns/pF)C L - 25 50 ns
t PLH LOW to HIGH propagation delay nCP0, nCP1 to nQn; see Fig. 5 5 V 83 ns + (0.55 ns/pF)C L - 110 220 ns
10 V 39 ns + (0.23 ns/pF)C L - 50 100 ns
15 V 32 ns + (0.16 ns/pF)C L - 40 80 ns
t t transition time nQn; see Fig. 5 5 V 10 ns + (1.00 ns/pF)C L - 60 120 ns
10 V 9 ns + (0.42 ns/pF)C L - 30 60 ns
15 V 6 ns + (0.28 ns/pF)C L - 20 40 ns
t W pulse width nCP0 input LOW; minimum width; see Fig. 5 5 V 60 30 - ns
10 V 30 15 - ns
15 V 20 10 - ns
nCP1 input HIGH; minimum width; see Fig. 5 5 V 60 30 - ns
10 V 30 15 - ns
15 V 20 10 - ns
nMR input HIGH; minimum width; see Fig. 5 5 V 30 15 - ns
10 V 20 10 - ns
15 V 16 8 - ns

5 / 12

Page 6

Symbol Parameter Conditions V DD Extrapolation formula [1] Min Typ Max Unit
t su set-up time nCP0 to nCP1; see Fig. 5 5 V 50 25 - ns
10 V 30 15 - ns
15 V 20 10 - ns
nCP1 to nCP0; see Fig. 5 5 V 50 25 - ns
10 V 30 15 - ns
15 V 20 10 - ns
t rec recovery time see Fig. 5 5 V 50 25 - ns
10 V 30 15 - ns
15 V 20 10 - ns
f max maximum frequency nCP0, nCP1; see Fig. 5 5 V 8 16 - MHz
10 V 15 30 - MHz
15 V 20 40 - MHz

[1] The typical values of the propagation delay and transition times are calculated from the extrapolation formulas shown (CL in pF).

Table 8. Dynamic power dissipation PD PD can be calculated from the formulas shown. VSS = 0 V; tr = tf ≤ 20 ns; Tamb = 25 °C.

Symbol Parameter V DD Typical formula for P (μW) D Where:
P D dynamic power dissipation 5 V P = 850 × f + Σ(f × C ) × V 2 D i o L DD f = input frequency in MHz, i f = output frequency in MHz, o C = output load capacitance in pF, L V = supply voltage in V, DD Σ(f × C ) = sum of the outputs. o L
10 V P = 3800 × f + Σ(f × C ) × V 2 D i o L DD
15 V P = 10200 × f + Σ(f × C ) × V 2 D i o L DD

6 / 12

Page 7

10.1. Waveforms and test circuit

PDF page 7 diagram

7 / 12

Page 8

PDF page 8 diagram

Table 9. Measurement points and test data

Supply voltage Input Load
V DD V I V M t, t r f C L
5 V to 15 V V DD 0.5 × V I ≤ 20 ns 50 pF

8 / 12

Page 9

11. Package outline

SO16: plastic small outline package; 16 leads; body width 3.9 mm

SOT109-1

PDF page 9 diagram
PDF page 9 diagram

Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included.

PDF page 9 diagram

Fig. 7. Package outline SOT109-1 (SO16)

9 / 12

Page 10

12. Abbreviations

Table 10. Abbreviations

Acronym Description
CDM Charged Device Model
DUT Device Under Test
ESD ElectroStatic Discharge
HBM Human Body Model
MM Machine Model

13. Revision history

Table 11. Revision history

Document ID Release date Data sheet status Change notice Supersedes
HEF4520B v.8 20220301 Product data sheet - HEF4520B v.7
Modifications: • The format of this data sheet has been redesigned to comply with the identity guidelines of Nexperia. • Legal texts have been adapted to the new company name where appropriate. • Section 1, Section 2, and Section 12 updated.
HEF4520B v.7 20160330 Product data sheet - HEF4520B v.6
Modifications: • Type number HEF4520BP (SOT38-4) removed.
HEF4520B v.6 20111118 Product data sheet - HEF4520B v.5
Modifications: • Section Applications removed • Table 6: I minimum values changed to maximum OH
HEF4520B v.5 20091210 Product data sheet - HEF4520B v.4
HEF4520B v.4 20090828 Product data sheet - HEF4520B_CNV v.3
HEF4520B_CNV v.3 19950101 Product specification - HEF4520B_CNV v.2
HEF4520B_CNV v.2 19950101 Product specification - -

10 / 12

Page 11

14. Legal information

Data sheet status

Document status [1][2] Product status [3] Definition
Objective [short] data sheet Development This document contains data from the objective specification for product development.
Preliminary [short] data sheet Qualification This document contains data from the preliminary specification.
Product [short] data sheet Production This document contains the product specification.

[1] Please consult the most recently issued document before initiating or completing a design. [2] The term 'short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the internet at https://www.nexperia.com.

Definitions

Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. Nexperia does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information.

Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local Nexperia sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail.

Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between Nexperia and its customer, unless Nexperia and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the Nexperia product is deemed to offer functions and qualities beyond those described in the Product data sheet.

Disclaimers

Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, Nexperia does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Nexperia takes no responsibility for the content in this document if provided by an information source outside of Nexperia.

In no event shall Nexperia be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory.

Notwithstanding any damages that customer might incur for any reason whatsoever, Nexperia’s aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of Nexperia.

Right to make changes — Nexperia reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof.

Suitability for use — Nexperia products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an Nexperia product can reasonably be expected to result in personal

injury, death or severe property or environmental damage. Nexperia and its suppliers accept no liability for inclusion and/or use of Nexperia products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk.

Quick reference data — The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding.

Applications — Applications that are described herein for any of these products are for illustrative purposes only. Nexperia makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification.

Customers are responsible for the design and operation of their applications and products using Nexperia products, and Nexperia accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the Nexperia product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products.

Nexperia does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using Nexperia products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). Nexperia does not accept any liability in this respect.

Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device.

Terms and conditions of commercial sale — Nexperia products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nexperia.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. Nexperia hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of Nexperia products by customer.

No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights.

Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities.

Non-automotive qualified products — Unless this data sheet expressly states that this specific Nexperia product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. Nexperia accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications.

In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without Nexperia’s warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond Nexperia’s specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies Nexperia for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond Nexperia’s standard warranty and Nexperia’s product specifications.

Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions.

Trademarks

Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners.

11 / 12

Page 12

Contents

  1. General description......................................................1 2. Features and benefits.................................................. 1 3. Ordering information....................................................1 4. Functional diagram.......................................................2 5. Pinning information......................................................3 5.1. Pinning.........................................................................3 5.2. Pin description.............................................................3 6. Functional description................................................. 3 7. Limiting values............................................................. 4
  1. Recommended operating conditions..........................4 9. Static characteristics....................................................4 10. Dynamic characteristics............................................ 5 10.1. Waveforms and test circuit........................................ 7 11. Package outline.......................................................... 9 12. Abbreviations............................................................10 13. Revision history........................................................10 14. Legal information......................................................11

For more information, please visit: http://www.nexperia.com For sales office addresses, please send an email to: salesaddresses@nexperia.com Date of release: 1 March 2022

12 / 12