HEF4094B NEXPERIA
Document overview
- PDF pages: 15
Technical content
Page 1
1. General description
The HEF4094B is an 8-bit serial-in/serial or parallel-out shift register with a storage register and 3-state outputs. Both the shift and storage register have separate clocks. The device features a serial input (D) and two serial outputs (QS1 and QS2) to enable cascading. Data is shifted on the LOW-to-HIGH transitions of the CP input. Data is available at QS1 on the LOW-to-HIGH transitions of the CP input to allow cascading when clock edges are fast. The same data is available at QS2 on the next HIGH-to-LOW transition of the CP input to allow cascading when clock edges are slow. The data in the shift register is transferred to the storage register when the STR input is HIGH.
Data in the storage register appears at the outputs whenever the output enable input (OE) is HIGH. A LOW on OE causes the outputs to assume a high-impedance OFF-state. Operation of the OE input does not affect the state of the registers. Inputs include clamp diodes. This enables the use of current limiting resistors to interface inputs to voltages in excess of VDD.
2. Features and benefits
- Fully static operation
- 5 V, 10 V, and 15 V parametric ratings
- Wide supply voltage range from 3.0 to 15.0 V
- CMOS low power dissipation
- High noise immunity
- Standardized symmetrical output characteristics
- ESD protection:
- HBM JESD22-A114F exceeds 2000 V
- MM JESD22-A115-A exceeds 200 V (C = 200 pF; R = 0 Ω)
- Complies with JEDEC standard JESD 13-B
- Specified from -40 °C to +85 °C and -40 °C to +125 °C
3. Ordering information
Table 1. Ordering information All types operate from -40 °C to +125 °C.
| Type number | Package | ||
|---|---|---|---|
| Name | Description | Version | |
| HEF4094BT | SO16 | plastic small outline package; 16 leads; body width 3.9 mm | SOT109-1 |
| HEF4094BTT | TSSOP16 | plastic thin shrink small outline package; 16 leads; body width 4.4 mm | SOT403-1 |
Page 2
4. Functional diagram
| D 2 8-STAGE SHIFT QS2 10 CP REGISTER 3 QS1 9 STR 8-BIT STORAGE 1 REGISTER OE 15 3-STATE OUTPUTS QP0 QP1 QP2 QP3 QP4 QP5 QP6 QP7 4 5 6 7 14 13 12 11 001aaf119 Fig. 1. Functional diagram | 3 1 CP STR QS1 9 QS2 10 QP0 4 QP1 5 QP2 6 2 D QP3 7 QP4 14 QP5 13 QP6 12 QP7 11 OE 15 001aaf111 Fig. 2. Logic symbol |
|---|---|
| STAGE 0 STAGES 1 TO 6 STAGE 7 D D Q D Q D Q QS1 CP CP FF 0 FF 7 D Q QS2 CP CP LE LATCH D Q D Q LE LE LATCH 0 LATCH 7 STR OE QP0 QP2 QP4 QP6 001aag799 QP1 QP3 QP5 QP7 Fig. 3. Logic diagram | |
2 / 15
Page 3
5. Pinning information
5.1. Pinning

5.2. Pin description
Table 2. Pin description
| Symbol | Pin | Description |
|---|---|---|
| STR | 1 | strobe input |
| D | 2 | data input |
| CP | 3 | clock input |
| QP0 to QP7 | 4, 5, 6, 7, 14, 13, 12, 11 | parallel output |
| V SS | 8 | ground supply voltage |
| QS1 | 9 | serial output |
| QS2 | 10 | serial output |
| OE | 15 | output enable input |
| V DD | 16 | supply voltage |
3 / 15
Page 4
6. Functional description
Table 3. Function table H = HIGH voltage level; L = LOW voltage level; X = don’t care; Z = HIGH-impedance OFF-state; NC = no change; ↑ = positive-going transition; ↓ = negative-going transition; Q6S = the data in register stage 6 before the LOW to HIGH clock transition; Q7S = the data in register stage 7 before the HIGH to LOW clock transition.
| Inputs | Parallel outputs | Serial outputs | |||||
| CP | OE | STR | D | QP0 | QPn | QS1 | QS2 |
| ↑ | L | X | X | Z | Z | Q6S | NC |
| ↓ | L | X | X | Z | Z | NC | Q7S |
| ↑ | H | L | X | NC | NC | Q6S | NC |
| ↑ | H | H | L | L | QPn -1 | Q6S | NC |
| ↑ | H | H | H | H | QPn -1 | Q6S | NC |
| ↓ | H | H | H | NC | NC | NC | Q7S |

4 / 15
Page 5
7. Limiting values
Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to VSS = 0 V (ground).
| Symbol | Parameter | Conditions | Min | Max | Unit |
|---|---|---|---|---|---|
| V DD | supply voltage | -0.5 | +18 | V | |
| I IK | input clamping current | V < -0.5 V or V > V + 0.5 V I I DD | - | ±10 | mA |
| V I | input voltage | -0.5 | V + 0.5 DD | V | |
| I OK | output clamping current | V < -0.5 V or V > V + 0.5 V O O DD | - | ±10 | mA |
| I I/O | input/output current | - | ±10 | mA | |
| I DD | supply current | - | 50 | mA | |
| T stg | storage temperature | -65 | +150 | °C | |
| T amb | ambient temperature | -40 | +125 | °C | |
| P tot | total power dissipation | [1] | - | 500 | mW |
| P | power dissipation | per output | - | 100 | mW |
[1] For SOT109-1 (SO16) package: Ptot derates linearly with 12.4 mW/K above 110 °C. For SOT403-1 (TSSOP16) package: Ptot derates linearly with 8.5 mW/K above 91 °C.
8. Recommended operating conditions
Table 5. Recommended operating conditions
| Symbol | Parameter | Conditions | Min | Typ | Max | Unit |
|---|---|---|---|---|---|---|
| V DD | supply voltage | 3 | - | 15 | V | |
| V I | input voltage | 0 | - | V DD | V | |
| T amb | ambient temperature | in free air | -40 | - | +125 | °C |
| Δt/ΔV | input transition rise and fall rate | V = 5 V DD | - | - | 3.75 | μs/V |
| V = 10 V DD | - | - | 0.5 | μs/V | ||
| V = 15 V DD | - | - | 0.08 | μs/V |
5 / 15
Page 6
9. Static characteristics
Table 6. Static characteristics VSS = 0 V; VI = VSS or VDD; unless otherwise specified.
| Symbol | Parameter | Conditions | V DD | T = -40 °C amb | T = +25 °C amb | T = +85 °C amb | T = +125 °C amb | Unit | ||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Min | Max | Min | Max | Min | Max | Min | Max | |||||
| V IH | HIGH-level input voltage | |I | < 1 μA O | 5 V | 3.5 | - | 3.5 | - | 3.5 | - | 3.5 | - | V |
| 10 V | 7.0 | - | 7.0 | - | 7.0 | - | 7.0 | - | V | |||
| 15 V | 11.0 | - | 11.0 | - | 11.0 | - | 11.0 | - | V | |||
| V IL | LOW-level input voltage | |I | < 1 μA O | 5 V | - | 1.5 | - | 1.5 | - | 1.5 | - | 1.5 | V |
| 10 V | - | 3.0 | - | 3.0 | - | 3.0 | - | 3.0 | V | |||
| 15 V | - | 4.0 | - | 4.0 | - | 4.0 | - | 4.0 | V | |||
| V OH | HIGH-level output voltage | |I | < 1 μA O | 5 V | 4.95 | - | 4.95 | - | 4.95 | - | 4.95 | - | V |
| 10 V | 9.95 | - | 9.95 | - | 9.95 | - | 9.95 | - | V | |||
| 15 V | 14.95 | - | 14.95 | - | 14.95 | - | 14.95 | - | V | |||
| V OL | LOW-level output voltage | |I | < 1 μA O | 5 V | - | 0.05 | - | 0.05 | - | 0.05 | - | 0.05 | V |
| 10 V | - | 0.05 | - | 0.05 | - | 0.05 | - | 0.05 | V | |||
| 15 V | - | 0.05 | - | 0.05 | - | 0.05 | - | 0.05 | V | |||
| I OH | HIGH-level output current | V = 2.5 V O | 5 V | - | -1.7 | - | -1.4 | - | -1.1 | - | -1.1 | mA |
| V = 4.6 V O | 5 V | - | -0.64 | - | -0.5 | - | -0.36 | - | -0.36 | mA | ||
| V = 9.5 V O | 10 V | - | -1.6 | - | -1.3 | - | -0.9 | - | -0.9 | mA | ||
| V = 13.5 V O | 15 V | - | -4.2 | - | -3.4 | - | -2.4 | - | -2.4 | mA | ||
| I OL | LOW-level output current | V = 0.4 V O | 5 V | 0.64 | - | 0.5 | - | 0.36 | - | 0.36 | - | mA |
| V = 0.5 V O | 10 V | 1.6 | - | 1.3 | - | 0.9 | - | 0.9 | - | mA | ||
| V = 1.5 V O | 15 V | 4.2 | - | 3.4 | - | 2.4 | - | 2.4 | - | mA | ||
| I OZ | OFF-state output current | QPn output is HIGH; V = 15 V O | 15 V | - | 0.4 | - | 0.4 | - | 12 | - | 12 | μA |
| I I | input leakage current | 15 V | - | ±0.1 | - | ±0.1 | - | ±1.0 | - | ±1.0 | μA | |
| I DD | supply current | all valid input combinations; I = 0 A O | 5 V | - | 5 | - | 5 | - | 150 | - | 150 | μA |
| 10 V | - | 10 | - | 10 | - | 300 | - | 300 | μA | |||
| 15 V | - | 20 | - | 20 | - | 600 | - | 600 | μA | |||
| C I | input capacitance | - | - | - | 7.5 | - | - | - | - | pF | ||
6 / 15
Page 7
10. Dynamic characteristics
Table 7. Dynamic characteristics VSS = 0 V; Tamb = 25 °C; for test circuit see Fig. 10; unless otherwise specified.
| Symbol | Parameter | Conditions | V DD | Extrapolation formula | Min | Typ | Max | Unit |
|---|---|---|---|---|---|---|---|---|
| t PHL | HIGH to LOW propagation delay | CP to QS1; see Fig. 6 | 5 V [1] | 108 ns + (0.55 ns/pF)C L | - | 135 | 270 | ns |
| 10 V | 54 ns + (0.23 ns/pF)C L | - | 65 | 130 | ns | |||
| 15 V | 42 ns + (0.16 ns/pF)C L | - | 50 | 100 | ns | |||
| CP to QS2; see Fig. 6 | 5 V | 78 ns + (0.55 ns/pF)C L | - | 105 | 210 | ns | ||
| 10 V | 39 ns + (0.23 ns/pF)C L | - | 50 | 100 | ns | |||
| 15 V | 32 ns + (0.16 ns/pF)C L | - | 40 | 80 | ns | |||
| CP to QPn; see Fig. 6 | 5 V | 138 ns + (0.55 ns/pF)C L | - | 165 | 330 | ns | ||
| 10 V | 64 ns + (0.23 ns/pF)C L | - | 75 | 150 | ns | |||
| 15 V | 47 ns + (0.16 ns/pF)C L | - | 55 | 110 | ns | |||
| STR to QPn; see Fig. 7 | 5 V | 83 ns + (0.55 ns/pF)C L | - | 110 | 220 | ns | ||
| 10 V | 39 ns + (0.23 ns/pF)C L | - | 50 | 100 | ns | |||
| 15 V | 27 ns + (0.16 ns/pF)C L | - | 35 | 70 | ns | |||
| t PLH | LOW to HIGH propagation delay, | CP to QS1; see Fig. 6 | 5 V [1] | 78 ns + (0.55 ns/pF)C L | - | 105 | 210 | ns |
| 10 V | 39 ns + (0.23 ns/pF)C L | - | 50 | 100 | ns | |||
| 15 V | 32 ns + (0.16 ns/pF)C L | - | 40 | 80 | ns | |||
| CP to QS2; see Fig. 6 | 5 V | 78 ns + (0.55 ns/pF)C L | - | 105 | 210 | ns | ||
| 10 V | 39 ns + (0.23 ns/pF)C L | - | 50 | 100 | ns | |||
| 15 V | 32 ns + (0.16 ns/pF)C L | - | 40 | 80 | ns | |||
| CP to QPn; see Fig. 6 | 5 V | 123 ns + (0.55 ns/pF)C L | - | 150 | 300 | ns | ||
| 10 V | 59 ns + (0.23 ns/pF)C L | - | 70 | 140 | ns | |||
| 15 V | 47 ns + (0.16 ns/pF)C L | - | 55 | 110 | ns | |||
| STR to QPn; see Fig. 7 | 5 V | 73 ns + (0.55 ns/pF)C L | - | 100 | 200 | ns | ||
| 10 V | 34 ns + (0.23 ns/pF)C L | - | 45 | 90 | ns | |||
| 15 V | 27 ns + (0.16 ns/pF)C L | - | 35 | 70 | ns | |||
| t t | transition time | 5 V [1] | 10 ns + (1.00 ns/pF)C L | - | 60 | 120 | ns | |
| 10 V | 9 ns + (0.42 ns/pF)C L | - | 30 | 60 | ns | |||
| 15 V | 6 ns + (0.28 ns/pF)C L | - | 20 | 40 | ns | |||
| t PZH | OFF-state to HIGH propagation delay | OE to QPn; see Fig. 8 | 5 V | - | 40 | 80 | ns | |
| 10 V | - | 25 | 50 | ns | ||||
| 15 V | - | 20 | 40 | ns | ||||
| t PZL | OFF-state to LOW propagation delay | OE to QPn; see Fig. 8 | 5 V | - | 40 | 80 | ns | |
| 10 V | - | 25 | 50 | ns | ||||
| 15 V | - | 20 | 40 | ns | ||||
| t PHZ | HIGH to OFF-state propagation delay | OE to QPn; see Fig. 8 | 5 V | - | 75 | 150 | ns | |
| 10 V | - | 40 | 80 | ns | ||||
| 15 V | - | 30 | 60 | ns | ||||
| t PLZ | LOW to OFF-state propagation delay | OE to QPn; see Fig. 8 | 5 V | - | 80 | 160 | ns | |
| 10 V | - | 40 | 80 | ns | ||||
| 15 V | - | 30 | 60 | ns |
7 / 15
Page 8
| Symbol | Parameter | Conditions | V DD | Extrapolation formula | Min | Typ | Max | Unit |
|---|---|---|---|---|---|---|---|---|
| t su | set-up time | D to CP; see Fig. 9 | 5 V | 60 | 30 | - | ns | |
| 10 V | 20 | 10 | - | ns | ||||
| 15 V | 15 | 5 | - | ns | ||||
| t h | hold time | D to CP; see Fig. 9 | 5 V | +5 | -15 | - | ns | |
| 10 V | 20 | 5 | - | ns | ||||
| 15 V | 20 | 5 | - | ns | ||||
| t W | pulse width | minimum LOW clock pulse; see Fig. 6 | 5 V | 60 | 30 | - | ns | |
| 10 V | 30 | 15 | - | ns | ||||
| 15 V | 24 | 12 | - | ns | ||||
| minimum HIGH strobe pulse; see Fig. 7 | 5 V | 40 | 20 | - | ns | |||
| 10 V | 30 | 15 | - | ns | ||||
| 15 V | 24 | 12 | - | ns | ||||
| f max | maximum frequency | see Fig. 6 | 5 V | 5 | 10 | - | MHz | |
| 10 V | 11 | 22 | - | MHz | ||||
| 15 V | 14 | 28 | - | MHz |
[1] The typical values of the propagation delay and transition times are calculated from the extrapolation formulas shown (CL in pF).
Table 8. Dynamic power dissipation VSS = 0 V; tr = tf ≤ 20 ns; Tamb = 25 °C.
| Symbol | Parameter | V DD | Typical formula for P (μW) D | where: |
|---|---|---|---|---|
| P D | dynamic power dissipation | 5 V | P = 2100 x f + Σ(f x C ) x V 2 D i o L DD | f = input frequency in MHz, i f = output frequency in MHz, o C = output load capacitance in pF, L V = supply voltage in V, DD Σ(f x C ) = sum of the outputs. o L |
| 10 V | P = 9700 x f + Σ(f x C ) x V 2 D i o L DD | |||
| 15 V | P = 26000 x f + Σ(f x C ) x V 2 D i o L DD |
10.1. Waveforms and test circuit

8 / 15
Page 9



9 / 15
Page 10
Table 9. Measurement points
| Supply voltage | Input | Output | ||
| V DD | V M | V M | V X | V Y |
| 5 V to 15 V | 0.5V DD | 0.5V DD | 0.1V DD | 0.9V DD |

Table 10. Test data
| Supply voltage | Input | V EXT | Load | ||||
| V DD | V I | t, t r f | t , t PHL PLH | t , t PHZ PZH | t , t PLZ PZL | C L | R L |
| 5 V to 15 V | V or V SS DD | ≤ 20 ns | open | V SS | V DD | 50 pF | 1 kΩ |
11. Application information
Some examples of applications for the HEF4094B are:
- Serial-to-parallel data conversion
- Remote control holding register

10 / 15
Page 11
12. Package outline
SO16: plastic small outline package; 16 leads; body width 3.9 mm
SOT109-1


Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included.

Fig. 12. Package outline SOT109-1 (SO16)
11 / 15
Page 12
TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm
SOT403-1



Fig. 13. Package outline SOT403-1 (TSSOP16)
12 / 15
Page 13
13. Abbreviations
Table 11. Abbreviations
| Acronym | Description |
|---|---|
| CMOS | Complementary Metal-Oxide Semiconductor |
| DUT | Device Under Test |
| ESD | ElectroStatic Discharge |
| HBM | Human Body Model |
| MM | Machine Model |
14. Revision history
Table 12. Revision history
| Document ID | Release date | Data sheet status | Change notice | Supersedes |
| HEF4094B v.14 | 20210708 | Product data sheet | - | HEF4094B v.13 |
| Modifications: | • Type number HEF4094BTS (SOT338-1 / SSOP16) removed. • Section 1 and Section 2 updated. • Section 7: Derating values for P total power dissipation updated. tot | |||
| HEF4094B v.13 | 20181114 | Product data sheet | - | HEF4094B v.11 |
| Modifications: | • The format of this data sheet has been redesigned to comply with the identity guidelines of Nexperia. • Legal texts have been adapted to the new company name where appropriate. • Fig. 5 corrected. | |||
| HEF4094B v.12 | 20160325 | Product data sheet | - | HEF4094B v.11 |
| Modifications: | • Type number HEF4094BP (SOT38-4) removed. | |||
| HEF4094B v.11 | 20130829 | Product data sheet | - | HEF4094B v.10 |
| Modifications: | • Table 4: Table note corrected (errata). | |||
| HEF4094B v.10 | 20130625 | Product data sheet | - | HEF4094B v.9 |
| Modifications: | • added type number HEF4094BTT. | |||
| HEF4094B v.9 | 20111116 | Product data sheet | - | HEF4094B v.8 |
| Modifications: | • Table 6: I minimum values changed to maximum OH | |||
| HEF4094B v.8 | 20100402 | Product data sheet | - | HEF4094B v.7 |
| HEF4094B v.7 | 20091216 | Product data sheet | - | HEF4094B v.6 |
| HEF4094B v.6 | 20091103 | Product data sheet | - | HEF4094B v.5 |
| HEF4094B v.5 | 20090728 | Product data sheet | - | HEF4094B v.4 |
| HEF4094B v.4 | 20081030 | Product data sheet | - | HEF4094B_CNV v.3 |
| HEF4094B_CNV v.3 | 19950101 | Product specification | - | HEF4094B_CNV v.2 |
| HEF4094B_CNV v.2 | 19950101 | Product specification | - | - |
13 / 15
Page 14
15. Legal information
Data sheet status
| Document status [1][2] | Product status [3] | Definition |
| Objective [short] data sheet | Development | This document contains data from the objective specification for product development. |
| Preliminary [short] data sheet | Qualification | This document contains data from the preliminary specification. |
| Product [short] data sheet | Production | This document contains the product specification. |
[1] Please consult the most recently issued document before initiating or completing a design. [2] The term 'short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the internet at https://www.nexperia.com.
Definitions
Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. Nexperia does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local Nexperia sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail.
Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between Nexperia and its customer, unless Nexperia and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the Nexperia product is deemed to offer functions and qualities beyond those described in the Product data sheet.
Disclaimers
Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, Nexperia does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Nexperia takes no responsibility for the content in this document if provided by an information source outside of Nexperia.
In no event shall Nexperia be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason whatsoever, Nexperia’s aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of Nexperia.
Right to make changes — Nexperia reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof.
Suitability for use — Nexperia products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an Nexperia product can reasonably be expected to result in personal
injury, death or severe property or environmental damage. Nexperia and its suppliers accept no liability for inclusion and/or use of Nexperia products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk.
Quick reference data — The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding.
Applications — Applications that are described herein for any of these products are for illustrative purposes only. Nexperia makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification.
Customers are responsible for the design and operation of their applications and products using Nexperia products, and Nexperia accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the Nexperia product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products.
Nexperia does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using Nexperia products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). Nexperia does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device.
Terms and conditions of commercial sale — Nexperia products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nexperia.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. Nexperia hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of Nexperia products by customer.
No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights.
Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities.
Non-automotive qualified products — Unless this data sheet expressly states that this specific Nexperia product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. Nexperia accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without Nexperia’s warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond Nexperia’s specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies Nexperia for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond Nexperia’s standard warranty and Nexperia’s product specifications.
Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions.
Trademarks
Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners.
14 / 15
Page 15
Contents
- General description......................................................1 2. Features and benefits.................................................. 1 3. Ordering information....................................................1 4. Functional diagram.......................................................2 5. Pinning information......................................................3 5.1. Pinning.........................................................................3 5.2. Pin description.............................................................3 6. Functional description................................................. 4 7. Limiting values............................................................. 5
- Recommended operating conditions..........................5 9. Static characteristics....................................................6 10. Dynamic characteristics............................................ 7 10.1. Waveforms and test circuit........................................ 8 11. Application information............................................10 12. Package outline........................................................ 11 13. Abbreviations............................................................13 14. Revision history........................................................13 15. Legal information......................................................14
For more information, please visit: http://www.nexperia.com For sales office addresses, please send an email to: salesaddresses@nexperia.com Date of release: 8 July 2021
15 / 15