HEF40373B NEXPERIA
Document overview
- PDF pages: 15
Technical content
Page 1
1 General description
The HEF40373B is an 8-bit transparent latch with 3-state buffered outputs. The output stages have high current output capability suitable for driving highly capacitive loads. The latch outputs follow the data inputs when the latch enable (E) is HIGH. When E is LOW, the data that meets the set-up times is latched. The 3-state outputs are controlled by the output enable input EO. A HIGH on EO causes the outputs to assume a high impedance OFF-state. The device features hysteresis on the E input to improve noise rejection. Schmitt-trigger action in the E input makes the circuit highly tolerant to slower input rise and fall times.
2 Features and benefits
- Octal bus interface
- 3-state buffers
- Fully static operation
- 5 V, 10 V, and 15 V parametric ratings
- Standardized symmetrical output characteristics
- Specified from −40 °C to +85 °C
3 Ordering information
Table 1. Ordering information
| Type number | Package | |||
|---|---|---|---|---|
| Temperature range | Name | Description | Version | |
| HEF40373BT | -40 °C to +85 °C | SO20 | plastic small outline package; 20 leads; body width 7.5 mm | SOT163-1 |
Page 2
4 Functional diagram
| 11 E 3 2 D0 O0 4 5 D1 O1 7 6 D2 O2 8 9 D3 O3 13 12 D4 O4 14 15 D5 O5 17 16 D6 O6 18 19 D7 O7 EO 1 aaa-028685 Figure 1. Logic symbol | 1 EO EN 11 E C1 3 2 D0 1D O0 4 5 D1 O1 7 6 D2 O2 8 9 D3 O3 13 12 D4 O4 14 15 D5 O5 17 16 D6 O6 18 19 D7 O7 aaa-028686 Figure 2. IEC logic symbol |
|---|---|
| D0 O0 3 2 D1 O1 4 5 D2 O2 7 6 D3 O3 8 LATCH 3-STATE 9 13 D4 1 TO 8 OUTPUTS O4 12 D5 O5 14 15 D6 O6 17 16 D7 O7 18 19 E 11 EO 1 aaa-028687 Figure 3. Functional diagram | LE LE LE D Q LE 001aae051 Figure 4. Logic diagram (one latch) |
| D0 D1 D2 D3 D4 D5 D6 D7 D Q D Q D Q D Q D Q D Q D Q D Q LATCH LATCH LATCH LATCH LATCH LATCH LATCH LATCH 1 2 3 4 5 6 7 8 LE LE LE LE LE LE LE LE LE LE LE LE LE LE LE LE E EO O0 O1 O2 O3 O4 O5 O6 O7 aaa-028688 Figure 5. Logic diagram | |
2 / 15
Page 3
5 Pinning information
5.1 Pinning

5.2 Pin description
Table 2. Pin description
| Symbol | Pin | Description |
|---|---|---|
| EO | 1 | output enable input (active low) |
| E | 11 | latch enable input |
| D0, D1, D2, D3, D4, D5, D6, D7 | 3, 4, 7, 8, 13, 14, 17, 18 | data inputs |
| O0, O1, O2, O3, O4, O5, O6, O7 | 2, 5, 6, 9, 12, 15, 16, 19 | data outputs |
| V SS | 10 | ground supply voltage |
| V DD | 20 | supply voltage |
3 / 15
Page 4
6 Functional description
Table 3. Function table [1]
| Operating mode | Inputs | Internal latches | Outputs On | ||
| EO | E | Dn | |||
| enable and read register (transparent mode) | L | H | L | L | L |
| L | H | H | H | H | |
| latch and read register | L | ↓ | l | L | L |
| L | ↓ | h | H | H | |
| Hold | L | L | X | NC | NC |
| Latch register and disable outputs | H | L | X | NC | Z |
| H | H | nDn | nDn | Z | |
[1] H = HIGH voltage level; L = LOW voltage level; ↓ = HIGH-to-LOW E transition; h = HIGH voltage level one set-up time prior to the HIGH-to-LOW E transition; l = LOW voltage level one set-up time prior to the HIGH-to-LOW E transition; X = don’t care; NC = No change; Z = high-impedance OFF-state.
7 Limiting values
Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134).
| Symbol | Parameter | Conditions | Min | Max | Unit |
|---|---|---|---|---|---|
| V DD | supply voltage | -0.5 | +18 | V | |
| V I | input voltage | -0.5 | V + 0.5 DD | V | |
| I DD | supply current | - | ±100 | mA | |
| I IK | input clamping current | - | ±10 | mA | |
| I OK | output clamping current | - | ±25 | mA | |
| T stg | storage temperature | -65 | +150 | °C | |
| T amb | ambient temperature | -40 | +85 | °C | |
| P tot | total power dissipation | T = -40 °C to +85 °C amb | |||
| SO20 package [1] | - | 500 | mW | ||
| P | power dissipation | per output | - | 100 | mW |
[1] For SO20 package: Ptot derates linearly with 8 mW/K above 70 °C.
4 / 15
Page 5
8 Recommended operating conditions
Table 5. Operating conditions
| Symbol | Parameter | Conditions | Min | Max | Unit |
|---|---|---|---|---|---|
| V DD | supply voltage | referenced to V (usually ground) SS | 3 | 15 | V |
| V I | input voltage | 0 | V DD | V | |
| T amb | ambient temperature | in free air | -40 | +85 | °C |
| Δt/ΔV | input transition rise and fall rate | V = 5 V DD | - | 3.75 | μs/V |
| V = 10 V DD | - | 0.5 | μs/V | ||
| V = 15 V DD | - | 0.08 | μs/V |
9 Static characteristics
Table 6. Static characteristics VSS = 0 V; VI = VSS or VDD unless otherwise specified.
| Symbol | Parameter | Conditions | T = -40 °C amb | T = 25 °C amb | T = 85 °C amb | Unit | |||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| V DD | Min | Max | Min | Typ | Max | Min | Max | ||||
| V IH | HIGH-level input voltage | |I | < 1 μA O | |||||||||
| V = 0.5 V or 4.5 V O | 5 V | 3.5 | - | 3.5 | - | - | 3.5 | - | V | ||
| V = 1.0 V or 9.0 V O | 10 V | 7.0 | - | 7.0 | - | - | 7.0 | - | V | ||
| V = 1.5 V or 13.5 V O | 15 V | 11.0 | - | 11.0 | - | - | 11.0 | - | V | ||
| V IL | LOW-level input voltage | |I | < 1 μA O | |||||||||
| V = 0.5 V or 4.5 V O | 5 V | - | 1.5 | - | - | 1.5 | - | 1.5 | V | ||
| V = 1.0 V or 9.0 V O | 10 V | - | 3.0 | - | - | 3.0 | - | 3.0 | V | ||
| V = 1.5 V or 13.5 V O | 15 V | - | 4.0 | - | - | 4.0 | - | 4.0 | V | ||
| V OH | HIGH-level output voltage | |I | < 1 μA O | 5 V | 4.95 | - | 4.95 | - | - | 4.95 | - | V |
| 10 V | 9.95 | - | 9.95 | - | - | 9.95 | - | V | |||
| 15 V | 14.95 | - | 14.95 | - | - | 14.95 | - | V | |||
| V OL | LOW-level output voltage | |I | < 1 μA O | 5 V | - | 0.05 | - | - | 0.05 | - | 0.05 | V |
| 10 V | - | 0.05 | - | - | 0.05 | - | 0.05 | V | |||
| 15 V | - | 0.05 | - | - | 0.05 | - | 0.05 | V | |||
| I OH | HIGH-level output current | see Figure 7 and Figure 8. | |||||||||
| V = 3.6 V OH | 5 V | −9.3 | - | −10 | −24 | - | −10.7 | - | mA | ||
| V = 4.6 V OH | 5 V | −0.75 | - | −0.6 | −1.2 | - | −0.45 | - | mA | ||
| V = 8.4 V OH | 10 V | −14.4 | - | −15 | −46 | - | −15 | - | mA | ||
| V = 9.5 V OH | 10 V | −1.85 | - | −1.5 | −3.0 | - | −1.1 | - | mA | ||
| V = 13.2 V OH | 15 V | −19.5 | - | −20 | −62 | - | −19.8 | - | mA | ||
| V = 13.5 V OH | 15 V | −14.5 | - | −15 | −50 | - | −15.5 | - | mA | ||
5 / 15
Page 6
| Symbol | Parameter | Conditions | T = -40 °C amb | T = 25 °C amb | T = 85 °C amb | Unit | |||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| V DD | Min | Max | Min | Typ | Max | Min | Max | ||||
| I OL | LOW-level output current | V = 0.4 V OL | 5 V | 2.9 | - | 2.3 | 5.4 | - | 1.75 | - | mA |
| V = 0.5 V OL | 10 V | 9.5 | - | 7.6 | 17 | - | 5.5 | - | mA | ||
| V = 1.5 V OL | 15 V | 30.0 | - | 25 | 45 | - | 19.0 | - | mA | ||
| I I | input leakage current | [1] | 15 V | - | ±0.3 | - | - | ±0.3 | - | ±1.0 | μA |
| I OZ | OFF-state output current | V = V O DD | 15 V | - | 1.6 | - | - | 1.6 | - | 12.0 | μA |
| V = V O SS | 15 V | - | −1.6 | - | - | −1.6 | - | −12.0 | μA | ||
| I DD | supply current | I = 0 A O | 5 V | - | 20.0 | - | - | 20.0 | - | 150 | μA |
| 10 V | - | 40.0 | - | - | 40.0 | - | 300 | μA | |||
| 15 V | - | 80.0 | - | - | 80.0 | - | 600 | μA | |||
| V H | hysteresis voltage | E input | 5 V | - | - | - | 220 | - | - | - | mV |
| 10 V | - | - | - | 250 | - | - | - | mV | |||
| 15 V | - | - | - | 320 | - | - | - | mV | |||
| C I | input capacitance | - | - | - | 7.5 | - | - | - | pF | ||
[1] Unused inputs must be connected to VDD, VSS or another input.
10 Dynamic characteristics
Table 7. Dynamic characteristics VSS = 0 V; Tamb = 25 °C; unless otherwise specified; for waveform and test circuit, see Figure 13.
| Symbol | Parameter | Conditions | Extrapolation formula | Min | Typ | Max | Unit |
|---|---|---|---|---|---|---|---|
| t PHL | HIGH to LOW propagation delay | E to On; see Figure 9. [1] | |||||
| V = 5 V DD | 138 ns + (0.24 ns/pF)C L | - | 150 | 300 | ns | ||
| V = 10 V DD | 59 ns + (0.01 ns/pF)C L | - | 60 | 120 | ns | ||
| V = 15 V DD | 36 ns + (0.07 ns/pF)C L | - | 40 | 80 | ns | ||
| t PLH | LOW to HIGH propagation delay | E to On; see Figure 9. [1] | |||||
| V = 5 V DD | 122 ns + (0.06 ns/pF)C L | - | 125 | 250 | ns | ||
| V = 10 V DD | 48 ns + (0.03 ns/pF)C L | - | 50 | 100 | ns | ||
| V = 15 V DD | 39 ns + (0.02 ns/pF)C L | - | 40 | 60 | ns | ||
| t PZH | OFF-state to HIGH propagation delay | EO to On; see Figure 11. | |||||
| V = 5 V DD | - | 65 | 130 | ns | |||
| V = 10 V DD | - | 30 | 60 | ns | |||
| V = 15 V DD | - | 25 | 50 | ns | |||
| t PZL | OFF-state to LOW propagation delay | EO to On; see Figure 11. | |||||
| V = 5 V DD | - | 85 | 170 | ns | |||
| V = 10 V DD | - | 35 | 70 | ns | |||
| V = 15 V DD | - | 25 | 50 | ns |
6 / 15
Page 7
| Symbol | Parameter | Conditions | Extrapolation formula | Min | Typ | Max | Unit |
|---|---|---|---|---|---|---|---|
| t PHZ | HIGH to OFF-state propagation delay | EO to On; see Figure 11. | |||||
| V = 5 V DD | - | 65 | 130 | ns | |||
| V = 10 V DD | - | 30 | 60 | ns | |||
| V = 15 V DD | - | 25 | 50 | ns | |||
| t PLZ | LOW to OFF-state propagation delay | EO to On; see Figure 11. | |||||
| V = 5 V DD | - | 75 | 150 | ns | |||
| V = 10 V DD | - | 40 | 80 | ns | |||
| V = 15 V DD | - | 30 | 60 | ns | |||
| t THL | HIGH to LOW output transition time | On; see Figure 9 and Figure 10. | |||||
| V = 5 V DD | - | 40 | 80 | ns | |||
| V = 10 V DD | - | 20 | 40 | ns | |||
| V = 15 V DD | - | 15 | 30 | ns | |||
| t TLH | LOW to HIGH output transition time | On; see Figure 9 and Figure 10. | |||||
| V = 5 V DD | - | 30 | 60 | ns | |||
| V = 10 V DD | - | 20 | 40 | ns | |||
| V = 15 V DD | - | 15 | 30 | ns | |||
| t su | set-up time | Dn to E; see Figure 12. | |||||
| V = 5 V DD | 15 | 7 | - | ns | |||
| V = 10 V DD | 10 | 5 | - | ns | |||
| V = 15 V DD | 10 | 5 | - | ns | |||
| t h | hold time | Dn to E; see Figure 12. | |||||
| V = 5 V DD | 25 | 15 | - | ns | |||
| V = 10 V DD | 15 | 4 | - | ns | |||
| V = 15 V DD | 10 | 3 | - | ns | |||
| t W | pulse width | E; LOW; see Figure 13. | |||||
| V = 5 V DD | 60 | 30 | - | ns | |||
| V = 10 V DD | 30 | 15 | - | ns | |||
| V = 15 V DD | 20 | 10 | - | ns |
[1] The typical values of the propagation delay are calculated from the extrapolation formulas shown (CL in pF).
Table 8. Dynamic power dissipation
| Symbol | Parameter | V DD | Typical formula | where: |
|---|---|---|---|---|
| P D | dynamic power dissipation | 5 V | P = 3325 × f + Σ(f × C ) × V 2 (μW) D i o L DD | f = input frequency in MHz; i f = output frequency in MHz; o C = output load capacitance in pF; L Σ(f × C ) = sum of the outputs; o L V = supply voltage in V. DD |
| 10 V | P = 14200 × f + Σ(f × C ) × V 2 (μW) D i o L DD | |||
| 15 V | P = 37425 × f + Σ(f × C ) × V 2 (μW) D i o L DD |
7 / 15
Page 8
10.1 Waveforms and test circuit


8 / 15
Page 9


9 / 15
Page 10

Table 9. Measurement points
| Supply voltage | Input | Output | ||
| V DD | V M | V M | V X | V Y |
| 5 V to 15 V | 0.5V DD | 0.5V DD | V + 0.1V OL DD | V − 0.1V OH DD |

Table 10. Test data
| Supply voltage | Input | Load | V EXT | ||||
| V I | t, t r f | C L | R L | t , t PLH PHL | t , t PHZ PZH | t , t PLZ PZL | |
| 5 V to 15 V | V DD | ≤ 20 ns | 50 pF | 1 kΩ | open | V SS | V DD |
10 / 15
Page 11
11 Package outline


Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included.
| OUTLINE VERSION | REFERENCES | EUROPEAN PROJECTION | ISSUE DATE | |||
| IEC | JEDEC | JEITA | ||||
| SOT163-1 | 075E04 | MS-013 | 99-12-27 03-02-19 | |||
Figure 14. Package outline SOT163-1 (SO20)
11 / 15
Page 12
12 Abbreviations
Table 11. Abbreviations
| Acronym | Description |
|---|---|
| DUT | Device Under Test |
13 Revision history
Table 12. Revision history
| Document ID | Release date | Data sheet status | Change notice | Supersedes |
| HEF40373B v.4 | 20180629 | Product data sheet | - | HEF40373B v.3 |
| Modifications: | • The format of this data sheet has been redesigned to comply with the identity guidelines of Nexperia. • Legal texts have been adapted to the new company name where appropriate. | |||
| HEF40373B v.3 | 19950101 | Product specification | - | HEF40373B v.2 |
| HEF40373B v.2 | 19950101 | Product specification | - | - |
12 / 15
Page 13
14 Legal information
14.1 Data sheet status
| Document status[1][2] | Product status[3] | Definition |
| Objective [short] data sheet | Development | This document contains data from the objective specification for product development. |
| Preliminary [short] data sheet | Qualification | This document contains data from the preliminary specification. |
| Product [short] data sheet | Production | This document contains the product specification. |
[1] Please consult the most recently issued document before initiating or completing a design. [2] The term 'short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nexperia.com.
14.2 Definitions
Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. Nexperia does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local Nexperia sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail.
Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between Nexperia and its customer, unless Nexperia and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the Nexperia product is deemed to offer functions and qualities beyond those described in the Product data sheet.
14.3 Disclaimers
Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, Nexperia does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Nexperia takes no responsibility for the content in this document if provided by an information source outside of Nexperia. In no event shall Nexperia be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal
or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, Nexperia's aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of Nexperia.
Right to make changes — Nexperia reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof.
Suitability for use — Nexperia products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical
systems or equipment, nor in applications where failure or malfunction of an Nexperia product can reasonably be expected to result in personal injury, death or severe property or environmental damage. Nexperia and its suppliers accept no liability for inclusion and/or use of Nexperia products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk.
Applications — Applications that are described herein for any of these products are for illustrative purposes only. Nexperia makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using Nexperia products, and Nexperia accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the Nexperia product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should
provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. Nexperia does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using Nexperia products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). Nexperia does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device.
Terms and conditions of commercial sale — Nexperia products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nexperia.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. Nexperia hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of Nexperia products by customer.
No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights.
Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities.
13 / 15
Page 14
Non-automotive qualified products — Unless this data sheet expressly states that this specific Nexperia product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. Nexperia accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without Nexperia's warranty of the product for such automotive applications,
use and specifications, and (b) whenever customer uses the product for automotive applications beyond Nexperia's specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies Nexperia for any liability, damages or failed product claims resulting from customer
design and use of the product for automotive applications beyond Nexperia's standard warranty and Nexperia's product specifications.
Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions.
14.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners.
14 / 15
Page 15
Contents
1 General description ............................................ 1 2 Features and benefits .........................................1 3 Ordering information .......................................... 1 4 Functional diagram .............................................2 5 Pinning information ............................................ 3 5.1 Pinning ...............................................................3 5.2 Pin description ...................................................3 6 Functional description ........................................4 7 Limiting values ....................................................4 8 Recommended operating conditions ................5
9 Static characteristics ..........................................5 10 Dynamic characteristics .....................................6 10.1 Waveforms and test circuit ................................ 8 11 Package outline .................................................11 12 Abbreviations .................................................... 12 13 Revision history ................................................ 12 14 Legal information ..............................................13
Please be aware that important notices concerning this document and the product(s) described herein, have been included in section 'Legal information'.
© Nexperia B.V. 2018.
All rights reserved.
For more information, please visit: http://www.nexperia.com For sales office addresses, please send an email to: salesaddresses@nexperia.com
Date of release: 29 June 2018 Document identifier: HEF40373B