6N137_06 FAIRCHILD
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 12
Technical content
Features
Superior CMR-10 kV/µs Double working voltage-480V Fan-out of 8 over -40°C to +85°C Logic gate output Strobable output Wired OR-open collector U.L. recognized (File # E90700)
Applications
LSTTL to TTL, LSTTL or 5-volt CMOS Line receiver, data transmission Data multiplexing Switching power supplies Pulse transformer replacement Computer-peripheral interface
Description
The 6N137, HCPL-2601/2611 single-channel and HCPL-2630/ 2631 dual-channel optocouplers consist of a 850 nm AlGaAS LED, optically coupled to a very high speed integrated photo- detector logic gate with a strobable output. This output features an open collector, thereby permitting wired OR outputs. The coupled parameters are guaranteed over the temperature range of -40°C to +85°C. A maximum input signal of 5 mA will provide a minimum output sink current of 13mA (fan out of 8). An internal noise shield provides superior common mode rejec- tion of typically 10kV/µs. The HCPL- 2601 and HCPL- 2631 has a minimum CMR of 5 kV/µs. The HCPL-2611 has a minimum CMR of 10 kV/µs. PackageS chematic Truth Table (Positive Logic) A 0.1µF bypass capacitor must be connected between pins 8 and 5. (See note 1) 4 5 8N/C VCC VE VO GND N/C VF 4 5 VF1 VCC V01 V02 GND VF2 HCPL-2630 HCPL-2631 6N137 HCPL-2601 HCPL-2611 Input Enable Output H H L L H H H L H L L H H NC L L NC H
www.fairchildsemi.com Single-Channel: 6N137, HCPL-2601, HCPL-2611 Dual-Channel: HCPL-2630, HCPL-2631 Rev. 1.0.5 Single-Channel: 6N137, HCPL-2601, HCPL-2611 Dual-Channel: HCPL-2630, HCPL-2631 High Speed-10 MBit/s Logic Gate Optocouplers Absolute Maximum Ratings A = 25°C unless otherwise specified) Recommended Operating Conditions *6.3mA is a guard banded value which allows for at least 20% CTR degradation. Initial input current threshold value is 5.0 mA or less. Parameter Symbol Value Units Storage Temperature T STG -55 to +125 °C Operating Temperature T OPR -40 to +85 °C Lead Solder Temperature T SOL 260 for 10 sec °C EMITTER DC/Average Forward Single Channel I F 50 mA Input Current Dual Channel (Each Channel) 30 Enable Input Voltage Not to exceed V CC by more than 500 mV Single Channel V E 5.5 V Reverse Input Voltage Each Channel V R 5.0 V Power Dissipation Single Channel P I 100 mW Dual Channel (Each Channel) DETECTOR Supply Voltage V CC (1 minute max) 7.0 V Output Current Single Channel I O 50 mA Dual Channel (Each Channel) 50 Output Voltage Each Channel V O 7.0 V Collector Output Single Channel P O 85 mW Power Dissipation Dual Channel (Each Channel) 60 Parameter Symbol Min Max Units Input Current, Low Level I FL 0 250 µA Input Current, High Level I FH *6.3 15 mA Supply Voltage, Output V CC 4.5 5.5 V Enable Voltage, Low Level V EL 0 0.8 V Enable Voltage, High Level V EH 2.0 V CC V Low Level Supply Current T A -40 +85 °C Fan Out (TTL load) N 8
www.fairchildsemi.com Single-Channel: 6N137, HCPL-2601, HCPL-2611 Dual-Channel: HCPL-2630, HCPL-2631 Rev. 1.0.5 Single-Channel: 6N137, HCPL-2601, HCPL-2611 Dual-Channel: HCPL-2630, HCPL-2631 High Speed-10 MBit/s Logic Gate Optocouplers
Electrical Characteristics
A = 0 to 70°C Unless otherwise specified) Individual Component Characteristics Switching Characteristics A = -40°C to +85°C, V CC = 5 V, I F = 7.5 mA Unless otherwise specified) Parameter Test Conditions Symbol Min Typ Max Unit EMITTER F = 10mA) V F 1.8 V Input Forward Voltage T A = 25°C 1.4 1.75 Input Reverse Breakdown Voltage (I R = 10µA) B VR 5.0 V Input Capacitance (V F = 0, f = 1 MHz) C IN 60 pF Input Diode Temperature Coefficient (I F = 10mA) V F T A -1.4 mV/°C DETECTOR High Level Supply Current Single Channel (V CC = 5.5 V, I F = 0 mA) I CCH 71 0 m A Dual Channel (V E = 0.5V) 10 15 Low Level Supply Current Single Channel (V CC = 5.5 V, I F = 10 mA) I CCL 91 3 m A Dual Channel (V E = 0.5V) 14 21 Low Level Enable Current (V CC = 5.5 V, V E = 0.5V) I EL -0.8 -1.6 mA High Level Enable Current (V CC = 5.5 V, V E = 2.0V) I EH -0.6 -1.6 mA High Level Enable Voltage (V CC = 5.5 V, I F = 10 mA) V EH 2.0 V Low Level Enable Voltage (V CC = 5.5 V, I F = 10 mA)(Note 3) V EL 0.8 V AC Characteristics Test Conditions Symbol Min Typ Max Unit Propagation Delay Time to Output High Level (Note 4) (T A = 25°C) T PLH 20 45 75 ns L = 350 Ω , C L = 15 pF) (Fig. 12) 100 Propagation Delay Time to Output Low Level (Note 5) (T A = 25°C) T PHL 25 45 75 ns L = 350 Ω , C L = 15 pF) (Fig. 12) 100 Pulse Width Distortion (R L = 350 Ω , C L = 15 pF) (Fig. 12) |T PHL T PLH 33 5 n s Output Rise Time (10-90%) L = 350 Ω , C L = 15 pF) (Note 6) (Fig. 12) t r 50 ns Output Rise Time (90-10%) L = 350 Ω , C L = 15 pF) (Note 7) (Fig. 12) t f 12 ns Enable Propagation Delay Time to Output High Level F = 7.5 mA, V EH = 3.5 V) L = 350 Ω , C L = 15 pF) (Note 8) (Fig. 13) t ELH 20 ns Enable Propagation Delay Time to Output Low Level F = 7.5 mA, V EH = 3.5 V) L = 350 Ω , C L = 15 pF) (Note 9) (Fig. 13) t EHL 20 ns Common Mode Transient Immunity (at Output High Level) A = 25°C) |V CM | = 50V, (Peak) F = 0 mA, V OH (Min.) = 2.0V) |CM H | V/µs 6N137, HCPL-2630 HCPL-2601, HCPL-2631 L = 350 Ω ) (Note 10) (Fig. 14) 5000 10,000 10,000 HCPL-2611 |V CM | = 400V 10,000 15,000 Common Mode Transient Immunity (at Output Low Level) L = 350 Ω ) (I F = 7.5 mA, V OL (Max.) = 0.8V |CM L | 10,000 V/µs 6N137, HCPL-2630 |V CM | = 50V (Peak) HCPL-2601, HCPL-2631 (T A = 25°C)(Note 11)(Fig. 14) 5000 10,000 HCPL-2611(TA = 25°C) |V CM| = 400V 10,000 15,000
4 www.fairchildsemi.com Single-Channel: 6N137, HCPL-2601, HCPL-2611 Dual-Channel: HCPL-2630, HCPL-2631 Rev. 1.0.5 Single-Channel: 6N137, HCPL-2601, HCPL-2611 Dual-Channel: HCPL-2630, HCPL-2631 High Speed-10 MBit/s Logic Gate Optocouplers Transfer Characteristics (TA = -40 to +85°C Unless otherwise specified) Isolation Characteristics (TA = -40°C to +85°C Unless otherwise specified.) All Typicals at VCC = 5V, TA = 25°C NOTES 1. The V CC supply to each optoisolator must be bypassed by a 0.1µF capacitor or larger. This can be either a ceramic or solid tantalum capacitor with good high frequency characteristic and should be connected as close as possible to the package VCC and GND pins of each device. 2. Each channel. 3. Enable Input - No pull up resistor required as the device has an internal pull up resistor. 4. t PLH -Propagation delay is measured from the 3.75 mA level on the HIGH to LOW transition of the input current pulse to the 1.5 V level on the LOW to HIGH transition of the output voltage pulse. 5. t PHL -Propagation delay is measured from the 3.75 mA level on the LOW to HIGH transition of the input current pulse to the 1.5 V level on the HIGH to LOW transition of the output voltage pulse. 6. t r -Rise time is measured from the 90% to the 10% levels on the LOW to HIGH transition of the output pulse. 7. t f -Fall time is measured from the 10% to the 90% levels on the HIGH to LOW transition of the output pulse. 8. t ELH -Enable input propagation delay is measured from the 1.5 V level on the HIGH to LOW transition of the input voltage pulse to the 1.5 V level on the LOW to HIGH transition of the output voltage pulse. 9. t EHL -Enable input propagation delay is measured from the 1.5 V level on the LOW to HIGH transition of the input voltage pulse to the 1.5 V level on the HIGH to LOW transition of the output voltage pulse. 10. CMH -The maximum tolerable rate of rise of the common mode voltage to ensure the output will remain in the high state (i.e., VOUT > 2.0 V). Measured in volts per microsecond (V/µs). 11. CML -The maximum tolerable rate of rise of the common mode voltage to ensure the output will remain in the low output state (i.e., VOUT < 0.8 V). Measured in volts per microsecond (V/µs). 12. Device considered a two-terminal device: Pins 1,2,3 and 4 shorted together, and Pins 5,6,7 and 8 shorted together. DC Characteristics Test Conditions Symbol Min Typ Max Unit High Level Output Current (V CC = 5.5 V, VO = 5.5 V) (IF = 250 µA, VE = 2.0 V) (Note 2) IOH 100 µA Low Level Output Current (V CC = 5.5 V, IF = 5 mA) (VE = 2.0 V, ICL = 13 mA) (Note 2) VOL .35 0.6 V Input Threshold Current (V CC = 5.5 V, VO = 0.6 V, VE = 2.0 V, IOL = 13 mA) IFT 3 5 mA Characteristics Test Conditions Symbol Min Typ** Max Unit Input-Output Insulation Leakage Current (Relative humidity = 45%) A = 25°C, t = 5 s) (VI-O = 3000 VDC) (Note 12) II-O 1.0* µA Withstand Insulation Test Voltage (RH < 50%, T A = 25°C) (II-O ≤ 2 µA) (Note 12) ( t = 1 min.) VISO 2500 V RMS Resistance (Input to Output) (V I-O = 500 V) (Note 12) R I-O 1012 Ω Capacitance (Input to Output) (f = 1 MHz) (Note 12) C I-O 0.6 pF
5 www.fairchildsemi.com Single-Channel: 6N137, HCPL-2601, HCPL-2611 Dual-Channel: HCPL-2630, HCPL-2631 Rev. 1.0.5 Single-Channel: 6N137, HCPL-2601, HCPL-2611 Dual-Channel: HCPL-2630, HCPL-2631 High Speed-10 MBit/s Logic Gate Optocouplers Fig.1 Low Level Output Voltage vs. Ambient Temperature TA - Ambient Temperature (°C) TA - Ambient Temperature (°C) TA - Ambient Temperature (°C) -40 -20 0 20 40 60 80 V OL - Low Level O utput Voltage (V) TP - Propagation Delay (ns) IF - Forward Cur rent (mA) IOL - Low Level Output Current (mA) V O - Output Voltage (V) IF - Forward Current (mA) IF - Forward Current (mA) IOL = 16 mA Fig. 4 Low Level Output Current vs. Ambient Temperature -40 -20 0 20 40 60 80 -40 -20 0 20 40 60 80 IF = 5 mA IF = 10 mA IF = 15 mA Fig. 5 Input Threshold Current vs. Ambient Temperature IFT - Input Threshold Current (mA) RL = 350 RL = 1kΩ RL = 4kΩ Fig. 6 Output Voltage vs. Input Forward Current RL = 350Ω RL = 1kΩ RL =4kΩ IOL = 6.4 mA IOL = 9.6 mA IOL = 12.8 mA Conditions: IF = 5 mA VE = 2 V VCC = 5.5V Conditions: VCC = 5.0 V VO = 0.6 V Fig. 2 Input Diode Forward Voltage vs. Forward Current VF - Forward Voltage (V) Conditions: VCC = 5 V VE = 2 V VOL = 0.6 V Fig.3 Switching Time vs. Forward Current 01 2 345 6 79 1 1 13 15 VCC = 5 V RL = 1 kΩ (TPLH) RL = 4 kΩ (TPLH) RL = 350 Ω (TPLH) RL = 1 kΩ RL = 4 kΩ RL = 350 kΩ (TPHL) 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 100 120 0.001 0.01 0.1
6 www.fairchildsemi.com Single-Channel: 6N137, HCPL-2601, HCPL-2611 Dual-Channel: HCPL-2630, HCPL-2631 Rev. 1.0.5 Single-Channel: 6N137, HCPL-2601, HCPL-2611 Dual-Channel: HCPL-2630, HCPL-2631 High Speed-10 MBit/s Logic Gate Optocouplers Fig. 7 Pulse Width Distortion vs. Temperature TA - Temperature (°C) T A - Temperature (°C) TA - Temperature (°C) TA - Temperature (°C) TA - Temperature (°C) -60 -40 -20 0 20 40 60 80 100 -60 -40 -20 0 20 40 60 80 100 -60 -40 -20 0 20 40 60 80 100 -60 -40 -20 0 20 40 60 80 100 -60 -40 -20 0 20 40 60 80 100 PWD - Pulse Width Distortion (ns) TE - Enable Propagation Delay (ns) IOH - High Level Output Current ( µA) TP - Propagation Delay (ns) Tr/Tf - Rise and Fall Time (ns) RL = 4 kΩ RL = 1 kΩ RL = 350Ω F Conditions: I = 7.5 mA VCC = 5 V Fig. 8 Rise and Fall Time vs. Temperature LR = 4 kΩ (tr) Conditions: IF = 7.5 mA VCC = 5 V RL = 1 kΩ (tr) RL = 350Ω (tr) RL = 1 kΩ RL = 4 kΩ (tf) RL = 350Ω Fig. 9 Enable Propagation Delay vs. Temperature RL = 4 kΩ (TELH) RL = 1 kΩ (TELH) RL = 350Ω (TELH) RL = 350Ω RL = 1 kΩ RL = 4 kΩ (TEHL) Fig. 10 Switching Time vs. Temperature RL = 1 kΩ TPLH RL = 350Ω TPLH RL = 4 kΩ TPLH RL = 1 kΩ RL = 4 kΩ RL = 350Ω TPHL Fig. 11 High Level Output Current vs. Temperature VCC = 5.5 V Conditions: VO = 5.5 V VE = 2.0 V IF = 250 µA 100 200 300 400 500 600 100 120 100 120
7 www.fairchildsemi.com Single-Channel: 6N137, HCPL-2601, HCPL-2611 Dual-Channel: HCPL-2630, HCPL-2631 Rev. 1.0.5 Single-Channel: 6N137, HCPL-2601, HCPL-2611 Dual-Channel: HCPL-2630, HCPL-2631 High Speed-10 MBit/s Logic Gate Optocouplers PHLt FI = 7.5 mA 1.5 V 90% 10% 7.5 mA +5V 1.5 V 3.0 V 1.5 V 4 5 Pulse Generator tr = 5ns Z = 50Ω O +5V GND PLHt I = 3.75 mAF Output O(V ) Input (I )F Output (V )O ft rt CCV Output (V )O LR CL(I ) Input F Monitor OZ = 50Ω Pulse Generator tr = 5ns (V ) E Input Monitor GND VCC O(V ) Output LR LC (V ) Output O Input (V )E EHLtt ELH bypass .1 µf bypass .1 µf Fig. 12 Test Circuit and Waveforms for tPLH, tPHL, tr and tf. Fig. 13 Test Circuit tEHL and tELH.
8 www.fairchildsemi.com Single-Channel: 6N137, HCPL-2601, HCPL-2611 Dual-Channel: HCPL-2630, HCPL-2631 Rev. 1.0.5 Single-Channel: 6N137, HCPL-2601, HCPL-2611 Dual-Channel: HCPL-2630, HCPL-2631 High Speed-10 MBit/s Logic Gate Optocouplers +5V Peak GND VCC O(V ) Output 350Ω VCM FFV A B Pulse Gen IF CMV OV Switching Pos. (A), I = 0F OV (Max) CM 0.5 V OV Switching Pos. (B), I = 7.5 mAF H CML V (Min)O bypass .1 µf Fig. 14 Test Circuit Common Mode Transient Immunity
9 www.fairchildsemi.com Single-Channel: 6N137, HCPL-2601, HCPL-2611 Dual-Channel: HCPL-2630, HCPL-2631 Rev. 1.0.5 Single-Channel: 6N137, HCPL-2601, HCPL-2611 Dual-Channel: HCPL-2630, HCPL-2631 High Speed-10 MBit/s Logic Gate Optocouplers NOTE All dimensions are in inches (millimeters) Package Dimensions (Through Hole) 0.200 (5.08) 0.140 (3.55) 0.100 (2.54) TYP 0.022 (0.56) 0.016 (0.41) 0.020 (0.51) MIN 0.390 (9.91) 0.370 (9.40) 0.270 (6.86) 0.250 (6.35) 0.070 (1.78) 0.045 (1.14) 241 56 7 8 0.300 (7.62) TYP 0.154 (3.90) 0.120 (3.05) 0.016 (0.40) 0.008 (0.20) 15° MAX PIN 1 ID. SEATING PLANE Package Dimensions (Surface Mount) Lead Coplanarity : 0.004 (0.10) MAX 0.270 (6.86) 0.250 (6.35) 0.390 (9.91) 0.370 (9.40) 0.022 (0.56) 0.016 (0.41) 0.100 (2.54) TYP 0.020 (0.51) MIN 0.070 (1.78) 0.045 (1.14) 0.300 (7.62) TYP 0.405 (10.30) MIN 0.315 (8.00) MIN 0.045 [1.14] 32 14 56 7 8 0.016 (0.41) 0.008 (0.20) PIN 1 ID. Package Dimensions (0.4"Lead Spacing) 0.200 (5.08) 0.140 (3.55) 0.100 (2.54) TYP 0.022 (0.56) 0.016 (0.41) 0.004 (0.10) MIN 0.390 (9.91) 0.370 (9.40) 0.270 (6.86) 0.250 (6.35) 0.070 (1.78) 0.045 (1.14) 241 56 7 8 0.400 (10.16) TYP 0.154 (3.90) 0.120 (3.05) 0.016 (0.40) 0.008 (0.20) 0° to 15° PIN 1 ID. SEA TING PLANE Recommended Pad Layout for Surface Mount Leadform 0.070 (1.78) 0.060 (1.52) 0.030 (0.76) 0.100 (2.54) 0.295 (7.49) 0.415 (10.54)
10 www.fairchildsemi.com Single-Channel: 6N137, HCPL-2601, HCPL-2611 Dual-Channel: HCPL-2630, HCPL-2631 Rev. 1.0.5 Single-Channel: 6N137, HCPL-2601, HCPL-2611 Dual-Channel: HCPL-2630, HCPL-2631 High Speed-10 MBit/s Logic Gate Optocouplers
Ordering Information
Option Example Part Number Description S 6N137S Surface Mount Lead Bend SD 6N137SD Surface Mount; Tape and reel W 6N137W 0.4" Lead Spacing V 6N137V VDE0884 WV 6N137WV VDE0884; 0.4” lead spacing SV 6N137SV VDE0884; surface mount SDV 6N137SDV VDE0884; surface mount; tape and reel QT Carrier Tape Specifications (“D” Taping Orientation) 4.0 ± 0.1 Ø1.55 ± 0.05 User Direction of Feed 4.0 ± 0.1 1.75 ± 0.10 7.5 ± 0.1 16.0 ± 0.3 12.0 ± 0.1 0.30 ± 0.05 13.2 ± 0.2 4.90 ± 0.20 0.1 MAX 10.30 ± 0.20 10.30 ± 0.20 Ø1.6 ± 0.1
11 www.fairchildsemi.com Single-Channel: 6N137, HCPL-2601, HCPL-2611 Dual-Channel: HCPL-2630, HCPL-2631 Rev. 1.0.5 Single-Channel: 6N137, HCPL-2601, HCPL-2611 Dual-Channel: HCPL-2630, HCPL-2631 High Speed-10 MBit/s Logic Gate Optocouplers Marking Information 43 5 Definitions 1F airchild logo 2D evice number
3 VDE mark (Note: Only appears on parts ordered with VDE option –
See order entry table) 4T wo digit year code, e.g., ‘03’ 5T wo digit work week ranging from ‘01’ to ‘53’
6 Assembly package code
Reflow Profile
- Peak reflow temperature: 225 C (package surface temperature)
- Time of temperature higher than 183 C for 60–150 seconds
- One time soldering reflow is recommended
215 C, 10–30 s
225 C peak
Time (Minute) 300 250 200 150 100 Temperature (°C) Time above 183 C, 60–150 sec Ramp up = 3 C/sec
12 www.fairchildsemi.com Single-Channel: 6N137, HCPL-2601, HCPL-2611 Dual-Channel: HCPL-2630, HCPL-2631 Rev. 1.0.5 Single-Channel: 6N137, HCPL-2601, HCPL-2611 Dual-Channel: HCPL-2630, HCPL-2631 High Speed-10 MBit/s Logic Gate Optocouplers Rev. I20 TRADEMARKS The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. PRODUCT STATUS DEFINITIONS Definition of Terms ACEx™ ActiveArray™ Bottomless™ Build it Now™ CoolFET™ CROSSVOLT™ DOME™ EcoSPARK™ E 2CMOS™ EnSigna™ FACT™ FAST® FASTr™ FPS™ FRFET™ FACT Quiet Series™ GlobalOptoisolator™ GTO™ HiSeC™ I 2C™ i-Lo™ ImpliedDisconnect™ IntelliMAX™ ISOPLANAR™ LittleFET™ MICROCOUPLER™ MicroFET™ MicroPak™ MICROWIRE™ MSX™ MSXPro™ OCX™ OCXPro™ OPTOLOGIC OPTOPLANAR™ PACMAN™ POP™ Power247™ PowerEdge™ PowerSaver™ PowerTrench® QFET® QS™ QT Optoelectronics™ Quiet Series™ RapidConfigure™ RapidConnect™ µSerDes™ ScalarPump™ SILENT SWITCHER SMART START™ SPM™ Stealth™ SuperFET™ SuperSOT™-3 SuperSOT™-6 SuperSOT™-8 SyncFET™ TCM™ TinyBoost™ TinyBuck™ TinyPWM™ TinyPower™ TinyLogic TINYOPTO™ TruTranslation™ UHC™ UniFET™ UltraFET® VCX™ Wire™ Across the board. Around the world.™ The Power Franchise Programmable Active Droop™ Datasheet Identification Product Status Definition Advance Information Formative or In Design This data sheet contains the design specifications for product development. Specifications may change in any manner without notice. Preliminary First Production This datasheet contains preliminary data, and supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. No Identification Needed Full Production This da tasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. Obsolete Not In Production This datasheet contains specifications on a product that has been discontinued by Fairchild semiconductor. The datasheet is printed for reference information only.