GTL2010 TI
Document overview
- Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 15
Technical content
www.ti.com
FEATURES
G REF D REF D10
APPLICATIONS
(TOP VIEW) With No Direction Control Required Allows Voltage Level Translation From V up to V Provides Direct Interface With GTL, GTL+, LVTTL/TTL, and 5-V CMOS Levels Low On-State Resistance Between Input and Output Pins (Sn/Dn) Supports Hot Insertion No Power Supply Required Will Not Latch Up 5-V-Tolerant Inputs Low Standby Current Flow-Through Pinout for Ease of Printed Circuit Board Trace Routing ESD Protection Exceeds JESD 2000-V Human-Body Model (A114-4) 1000-V Charged-Device Model (C101) Bidirectional or Unidirectional V to to Any Voltage V to Low Voltage Processor I C Port Translation to 3.3-V and/or 5-V I C Bus Signal Levels GTL/GTL+ Translation to LVTTL/TTL Signal Levels The GTL2010 provides ten NMOS pass transistors (Sn and Dn) with a common gate REF and a reference transistor REF and D REF The low ON-state resistance of the switch allows connections to be made with minimal propagation delay. With no direction control pin required, the device allows bidirectional voltage translations any voltage V to to any voltage V to V). When the Sn or Dn port is LOW, the clamp is in the ON state and a low-resistance connection exists between the Sn and Dn ports. Assuming the higher voltage is on the Dn port, when the Dn port is HIGH, the voltage on the Sn port is limited to the voltage set by the reference transistor REF When the Sn port is HIGH, the Dn port is pulled to V CC by the pullup resistors. Please be aware that an important notice concerning availability, standard warranty, and use in critical sheet. PRODUCTION DATA information is current as of publication date. Copyright 2006, Texas Instruments Incorporated Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.
www.ti.com DESCRIPTION/ORDERING INFORMATION (CONTINUED) GTL2010 10-BIT BIDIRECTIONAL LOW-VOLTAGE TRANSLATOR SCDS221 SEPTEMBER 2006 All transistors in the GTL2010 have the same electrical characteristics, and there is minimal deviation from one output to another in voltage or propagation delay. This offers superior matching over discrete transistor voltage-translation solutions where the fabrication of the transistors is not symmetrical. With all transistors being identical, the reference transistor REF REF can be located on any of the other ten matched Sn/Dn transistors, allowing for easier board layout. The translator transistors with integrated ESD circuitry provides excellent ESD protection. ORDERING INFORMATION T A PACKAGE (1) ORDERABLE PART NUMBER TOP-SIDE MARKING C to C TSSOP PW Tape and reel SN74GTL2010PWR GK2010 (1) Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. PIN
DESCRIPTION
NO. NAME S REF Source of reference transistor Sn Ports Dn Ports D10 D REF Drain of reference transistor G REF Gate of reference transistor Submit Documentation Feedback
www.ti.com SA00647 SREF S1 S10 D REF D1 D10G REF GTL2010 10-BIT BIDIRECTIONAL LOW-VOLTAGE TRANSLATOR SCDS221 SEPTEMBER 2006 FUNCTION TABLES (1) ABC HIGH-to-LOW Translation (Assuming Dn is at the Higher Voltage Level) INPUTS OUTPUTS G REF (2) D REF S REF TRANSISTOR D10 S10 H H V X X Off H H V TT (3) H V TT (4) On H H V TT L L (5) On L L V TT X X Off (1) H HIGH voltage level, L LOW voltage level, X don't care (2) G REF should be at least 1.5 V higher than S REF for best translator operation. (3) V TT is equal to the S REF voltage. (4) Sn is not pulled up or pulled down. (5) Sn follows the Dn input LOW. LOW-to-HIGH Translation (Assuming Dn is at the Higher Voltage Level) (1) INPUTS OUTPUTS G REF (2) D REF S REF TRANSISTOR D10 S10 H H V X X Off H H V TT (3) V TT H (4) Nearly off H H V TT L L (5) On L L V TT X X Off (1) H HIGH voltage level, L LOW voltage level, X don't care (2) G REF should be at least 1.5 V higher than S REF for best translator operation. (3) V TT is equal to the S REF voltage. (4) Dn is pulled up to V CC through an external resistor. (5) Dn follows the Sn input LOW. CLAMP SCHEMATIC Submit Documentation Feedback
www.ti.com Absolute Maximum Ratings (1) (2) (3) Recommended Operating Conditions GTL2010 10-BIT BIDIRECTIONAL LOW-VOLTAGE TRANSLATOR SCDS221 SEPTEMBER 2006 MIN MAX UNIT V SREF DC source reference voltage 0.5 V V DREF DC drain reference voltage 0.5 V V GREF DC gate reference voltage 0.5 V V Sn DC voltage port Sn 0.5 V V Dn DC voltage port Dn 0.5 V I REFK DC diode current on reference pins V I V mA I SK DC diode current port Sn V I V mA I DK DC diode current port Dn V I V mA I MAX DC clamp current per channel Channel in ON state 128 mA θ JA Package thermal impedance C/W T stg Storage temperature range 150 C (1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. (2) The performance capability of a high-performance integrated circuit in conjunction with its thermal environment can create junction temperatures that are detrimental to reliability. The maximum junction temperature of this integrated circuit should not exceed 150 (3) The input and output negative voltage ratings may be exceeded if the input and output clamp current ratings are observed. MIN MAX UNIT V I/O Input/output voltage (Sn, Dn) 5.5 V V SREF DC source reference voltage (1) 5.5 V V DREF DC drain reference voltage 5.5 V V GREF DC gate reference voltage 5.5 V I PASS Pass transistor current mA T amb Operating ambient temperature range (in free air) C (1) V SREF V DREF 1.5 V for best results in level-shifting applications. Submit Documentation Feedback
www.ti.com Electrical Characteristics GTL2010 10-BIT BIDIRECTIONAL LOW-VOLTAGE TRANSLATOR SCDS221 SEPTEMBER 2006 over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP (1) MAX UNIT V DD V SREF 1.365 V Sn or V Dn 0.175 V OL Low-level output voltage 260 350 mV I clamp 15.2 mA V IK Input clamp voltage I I mA, V GREF V 1.2 V I IH Gate input leakage V I V GREF V µ A C I(GREF) Gate capacitance V I V or V pF C IO(OFF) OFF capacitance V O V or V GREF V 7.4 pF C IO(ON) ON capacitance V O V or V GREF V 18.6 pF V GREF 4.5 V 3.5 V GREF V 4.4 I O mA V I V V GREF 2.3 V 5.5 V GREF 1.5 V 105 r on (2) ON-state resistance Ω V GREF 1.5 I O mA V GREF 4.5 V V I 2.4 V V GREF V I O mA V I 1.7 V V GREF 2.3 V (1) All typical values are measured at T amb (2) Measured by the voltage drop between the Sn and the Dn terminals at the indicated current through the switch. On-state resistance is determined by the lowest voltage of the two (Sn or Dn) terminals. Submit Documentation Feedback
www.ti.com AC Characteristics for Translator-Type (1) VI VMVM VM VM VM VM tPHL tPLH tPHL0 tPHL1 tPLH0 tPLH1 GND VDD2 VDD2 VOL VOL Input Low-to-High Low-to-High AC W aveforms Vm = 1.5 V, VIN = GND to 3 V VDD2VDD2 VDD2 VDD2 SREF G REF VREF D REF DUT Test Jig Pulse Generator 150 /C0087 150 /C0087 150 /C0087200 /C0087 D1 . . . D10 S1 . . . S10 GTL2010 10-BIT BIDIRECTIONAL LOW-VOLTAGE TRANSLATOR SCDS221 SEPTEMBER 2006 V REF 1.365 V to 1.635 V DD1 V to 3.6 V DD2 2.36 V to 2.64 GND t r t f ns, T amb C to C (see Figure PARAMETER MIN TYP (2) MAX UNIT t PLH (3) Propagation delay (Sn to Dn, Dn to Sn) 0.5 1.5 5.5 ns (1) C ON(max) of pF and a C OFF(max) of pF is specified by design. (2) All typical values are measured at V DD1 3.3 V DD2 2.5 V REF 1.5 V and T amb (3) Propagation delay specified by characterization. Figure Input (Sn) to Output (Dn) Propagation Delays Figure Load Circuit Submit Documentation Feedback
www.ti.com AC Characteristics for CBT-Type 1.5 V1.5 V 1.5 V1.5 V 3 V 0 V tPLH tPHL AC W aveforms TEST S1 Open 7 V Open Load Circuit C L = 50 pF 500 /C0087 500 /C0087
7 VS1From Ouput
C L = Load capacitance, includes jig and probe capacitance (see AC Characteristics for value). GTL2010 10-BIT BIDIRECTIONAL LOW-VOLTAGE TRANSLATOR SCDS221 SEPTEMBER 2006 GND t R C L pF, G REF V 0.5 T amb C to C PARAMETER MIN MAX UNIT t pd Propagation delay (1) 250 ps (1) This parameter is warranted but not production tested. The propagation delay is based on the RC time constant of the typical on-state resistance of the switch and a load capacitance of pF, when driven by an ideal voltage source (zero output impedance). Figure Input (Sn) to Output (Dn) Propagation Delays Figure Load Circuit Submit Documentation Feedback
www.ti.com APPLICATION INFORMATION Bidirectional Translation GTL2010 10-BIT BIDIRECTIONAL LOW-VOLTAGE TRANSLATOR SCDS221 SEPTEMBER 2006 For the bidirectional clamping configuration (higher voltage to lower voltage or lower voltage to higher voltage), the G REF input must be connected to D REF and both pins pulled to HIGH-side V CC through a pullup resistor (typically 200 k Ω A filter capacitor on D REF is recommended. The processor output can be totem pole or open drain (pullup resistors) and the chipset output can be totem pole or open drain (pullup resistors are required to pull the Dn outputs to V CC However, if either output is totem pole, data must be unidirectional or the outputs must be 3-statable, and the outputs must be controlled by some direction-control mechanism to prevent HIGH-to-LOW contentions in either direction. If both outputs are open drain, no direction control is needed. The opposite side of the reference transistor REF is connected to the processor core power-supply voltage. When D REF is connected through a 200-k Ω resistor to a 3.3-V to 5.5-V V CC supply and S REF is set between V to V CC 1.5 the output of each Sn has a maximum output voltage equal to S REF and the output of each Dn has a maximum output voltage equal to V CC Submit Documentation Feedback
www.ti.com SREF DREF GREF SW SW GTL2010 D1S1 D2S2 RPU RPU RPU RPU RPU V =□5VDPU V =□3.3VDPU V =□1.8VREF RPU 200K Ω CPU□I/O Chipset I/O Chipset I/O S9 D9 D10S10 GND GTL2010 10-BIT BIDIRECTIONAL LOW-VOLTAGE TRANSLATOR SCDS221 SEPTEMBER 2006 APPLICATION INFORMATION (continued) Figure Bidirectional Translation to Multiple Higher Voltage Levels (Such as an I C or SMBus Applications) Submit Documentation Feedback
www.ti.com Unidirectional Down Translation SREF DREF GREF SW SW GTL2010 D1S1 D2S2 Sn GND Dn V =□5VDPU V =□1.8VREF 200K Ω CPU□I/O Chipset I/O GTL2010 10-BIT BIDIRECTIONAL LOW-VOLTAGE TRANSLATOR SCDS221 SEPTEMBER 2006 APPLICATION INFORMATION (continued) For unidirectional clamping (higher voltage to lower voltage), the G REF input must be connected to D REF and both pins pulled to the higher-side V CC through a pullup resistor (typically 200 k Ω A filter capacitor on D REF is recommended. Pullup resistors are required if the chipset I/Os are open drain. The opposite side of the reference transistor REF is connected to the processor core power-supply voltage. When D REF is connected through a 200-k Ω resistor to a 3.3-V to 5.5-V V CC supply and S REF is set between V to V CC 1.5 the output of each Sn has a maximum output voltage equal to S REF Figure Unidirectional Down Translation to Protect Low-Voltage Processor Pins Submit Documentation Feedback
www.ti.com Unidirectional Up Translation SREF DREF GREF SW SW GTL2010 D1S1 D2S2 Sn GND Dn RPU RPU RPU V =□5VDPU V =□1.8VREF RPU 200K Ω CPU□I/O Chipset I/O GTL2010 10-BIT BIDIRECTIONAL LOW-VOLTAGE TRANSLATOR SCDS221 SEPTEMBER 2006 APPLICATION INFORMATION (continued) For unidirectional up translation (lower voltage to higher voltage), the reference transistor is connected the same as for a down translation. A pullup resistor is required on the higher voltage side (Dn or Sn) to get the full HIGH level, since the GTL device only passes the reference source REF voltage as a HIGH when doing an up translation. The driver on the lower voltage side only needs pullup resistors if it is open drain. Figure Unidirectional Up Translation to Higher-Voltage Chipsets Submit Documentation Feedback
www.ti.com Sizing Pullup Resistor Resistor value(/C0087)/C0043Pullup voltage (V)/C00420.35 V 0.015 A GTL2010 10-BIT BIDIRECTIONAL LOW-VOLTAGE TRANSLATOR SCDS221 SEPTEMBER 2006 APPLICATION INFORMATION (continued) The pullup resistor value should limit the current through the pass transistor when it is in the on state to about mA. This ensures a pass voltage of 260 mV to 350 mV. If the current through the pass transistor is higher than mA, the pass voltage also is higher in the on state. To set the current through each pass transistor at mA, the pullup resistor value is calculated as: Table shows resistor values for various reference voltages and currents at mA, mA, and mA. The resistor value shown in the +10% column, or a larger value, should be used to ensure that the pass voltage of the transistor would be 350 mV or less. The external driver must be able to sink the total current from the resistors on both sides of the GTL device at 0.175 although the mA only applies to current flowing through the GTL2010. Table Pullup Resistor Values (1) (2) (3) PULLUP RESISTOR VALUE Ω mA mA mA VOLTAGE NOMINAL +10% NOMINAL +10% NOMINAL +10% 5.0 V 310 341 465 512 1550 1705 3.3 V 197 217 295 325 983 1082 2.5 V 143 158 215 237 717 788 1.8 V 106 145 160 483 532 1.5 V 115 127 383 422 1.2 V 283 312 (1) Calculated for V OL 0.35 V (2) Assumes output driver V OL 0.175 V at stated current (3) +10% to compensate for V DD range and resistor tolerance Submit Documentation Feedback
Orderable Device Status(1) Package Type Package Drawing Pins Package Qty Eco Plan(2) Lead/Ball FinishMSL Peak Temp (3) SN74GTL2010PW ACTIVE TSSOP PW 24 60 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74GTL2010PWE4 ACTIVE TSSOP PW 24 60 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74GTL2010PWR ACTIVE TSSOP PW 24 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74GTL2010PWRE4 ACTIVE TSSOP PW 24 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM (1)The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2)Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontentfor the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS):TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt):This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br):TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. PACKAGE OPTION ADDENDUM www.ti.com 6-Dec-2006 Addendum-Page 1
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,65 M0,10 0,10 0,25 0,50 0,75 0,15 NOM Gage Plane 9,80 9,60 7,90 7,70 2016 6,60 6,40 4040064/F 01/97 0,30 6,60 6,20 0,19 4,30 4,50 0,15 A 1,20 MAX 5,10 4,90 3,10 2,90 A MAX A MIN DIM PINS ** 0,05 4,90 5,10 Seating Plane 0°–8° NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. C. Body dimensions do not include mold flash or protrusion not to exceed 0,15. D. Falls within JEDEC MO-153
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Low Power Wireless www.ti.com/lpw Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2006, Texas Instruments Incorporated