GTL2007 NXP

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 20

Technical content

  1. General description The GTL2007 is a customized translator between dual Xeon processors, Platform Health Management, South Bridge and Power Supply LVTTL and GTL signals. The GTL2007 is derived from the GTL2006 with an enable function added that disables the error output to the monitoring agent for platforms that monitor the individual error conditions from each processor. This enable function can be used so that false error conditions are not passed to the monitoring agent when the system is unexpectedly powered down. This unexpected power-down could be from a power supply overload, a CPU thermal trip, or some other event of which the monitoring agent is unaware. A typical implementation would be to connect each enable line to the system power good signal or the individual enables to the VRD power good for each processor. Typically Xeon processors specify a V TT of 1.1 V to 1.2 V, as well as a nominal Vref of 0.73 V to 0.76 V. To allow for future voltage level changes that may extend Vref to 0.63 of VTT (minimum of 0.693 V with VTT of 1.1 V) the GTL2007 allows a minimum Vrefof 0.66 V. Characterization results show that there is little DC or AC performance variation between these V ref levels. 2. Features n Operates as a GTL to LVTTL sampling receiver or LVTTL to GTL driver n Operates at GTL−/GTL/GTL+ signal levels n EN1 and EN2 disable error output n 3.0 V to 3.6 V operation n LVTTL I/O not 5 V tolerant n Series termination on the LVTTL outputs of 30Ω n ESD protection exceeds 2000 V HBM per JESD22-A114, 200 V MM per JESD22-A115, and 1000 V CDM per JESD22-C101 n Latch-up testing is done to JEDEC Standard JESD78 which exceeds 500 mA n Package offered: TSSOP28 GTL2007 12-bit GTL to LVTTL translator with power good control Rev. 02 — 16 February 2007 Product data sheet

GTL2007_2 © NXP B.V. 2007. All rights reserved. Table 1. Quick reference data Table 2. Ordering information

GTL2007_2 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 02 — 16 February 2007 3 of 20 NXP Semiconductors GTL2007 12-bit GTL to LVTTL translator with power good control 5. Functional diagram (1) The enable on 7BO1/7BO2 include a delay that prevents the transient condition where 5BI/6BI go from LOW to HIGH, and the LOW to HIGH on 5A/6A lags up to 100 ns from causing a LOW glitch on the 7BO1/7BO2 outputs. Fig 1. Logic diagram of GTL2007 002aab210 GTL2007 1BI 2BI GTL inputs 7BO125 7BO224 GTL outputs EN223 LVTTL input 11BO22 GTL output DELAY (1) 5BI 6BI 3BI19 4BI18 DELAY (1) GTL inputs 11BI 811A 99BI LVTTL input/output (open-drain) GTL input GTL input 1VREF 21AO 32AO 45A 56A 6EN1LVTTL input GTL LVTTL inputs/outputs (open-drain) LVTTL outputs 103AO 114AO LVTTL outputs 10BO117 10BO216 GTL outputs 1210AI1 1310AI2 LVTTL inputs 9AO15 LVTTL output

GTL2007_2 © NXP B.V. 2007. All rights reserved.

6.1 Pinning

6.2 Pin description

Table 3. Pin description

GTL2007_2 © NXP B.V. 2007. All rights reserved. Refer toFigure 1 “Logic diagram of GTL2007”.

7.1 Function tables

Table 3. Pin description …continued Table 4. GTL input signals H = HIGH voltage level; L = LOW voltage level. Table 5. EN1 power good signal H = HIGH voltage level; L = LOW voltage level. Table 6. EN2 power good signal H = HIGH voltage level; L = LOW voltage level.

GTL2007_2 © NXP B.V. 2007. All rights reserved. [2] Open-drain input/output terminal is driven to logic LOW state by other driver. [1] Open-drain input/output terminal is driven to logic LOW state by other driver. Table 7. SMI signals H = HIGH voltage level; L = LOW voltage level. Table 8. PROCHOT signals H = HIGH voltage level; L = LOW voltage level. Table 9. NMI signals H = HIGH voltage level; L = LOW voltage level.

GTL2007_2 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 02 — 16 February 2007 7 of 20 NXP Semiconductors GTL2007 12-bit GTL to LVTTL translator with power good control 8. Application design-in information Fig 3. Typical application THRMTRIP L CPU1 IERR_L FORCEPR_L CPU2 DISABLE_L GTL2007 PROCHOT L FORCEPR_L PROCHOT L THRMTRIP L IERR_L CPU1 DISABLE_L CPU2 NMI NMI 10BO2 10BO1 4BI 3BI 6BI 5BI EN2 7BO2 7BO1 2BI 1BI1AO 2AO 11A 3AO 4AO 10AI1 10AI2 EN1 GND 9BI 9AO PLATFORM HEALTH MANAGEMENT CPU1 1ERR_L CPU1 THRMTRIP L CPU1 PROCHOT L CPU2 PROCHOT L NMI_L CPU2 1ERR_L CPU2 THRMTRIP L CPU1 SMI L CPU2 SMI L SMI_BUFF_L SOUTHBRIDGE NMI SOUTHBRIDGE SMI_L power supply POWER GOOD 1.5 kW to 1.2 kW VCC VTT 56 W 1.5 kW R VREF 11B1 VCC VCC 11B0 002aab211 56 W VTT

GTL2007_2 © NXP B.V. 2007. All rights reserved. device at these or any other conditions beyond those indicated underSection 10 “Recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. [2] The input and output negative voltage ratings may be exceeded if the input and output clamp current ratings are observed. [3] Current into any output in the LOW state. [4] Current into any output in the HIGH state. temperatures which are detrimental to reliability. The maximum junction temperature of this integrated circuit should not exceed 150°C.

  1. Recommended operating conditions

Table 10. Limiting values Voltages are referenced to GND (ground=0V ) . Table 11. Operating conditions

GTL2007_2 © NXP B.V. 2007. All rights reserved. [1] All typical values are measured at VCC = 3.3 V and Tamb =2 5°C. [2] The input and output voltage ratings may be exceeded if the input and output current ratings are observed. Table 12. Static characteristics Recommended operating conditions; voltages are referenced to GND (ground = 0 V). Tamb = −40 °C to +85°C.

GTL2007_2 © NXP B.V. 2007. All rights reserved. Table 13. Dynamic characteristics

GTL2007_2 © NXP B.V. 2007. All rights reserved. [1] All typical values are at VCC = 3.3 V and Tamb =2 5°C. [2] Includes ~7.6 ns RC rise time of test load pull-up on 11A, 1.5 kΩ pull-up and 21 pF load on 11A has about 23 ns RC rise time.

12.1 Waveforms

VM = 1.5 V at VCC ≥ 3.0 V for A ports; VM =V reffor B ports. Table 13. Dynamic characteristics …continued

GTL2007_2 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 02 — 16 February 2007 12 of 20 NXP Semiconductors GTL2007 12-bit GTL to LVTTL translator with power good control PRR ≤ 10 MHz; ZO =5 0Ω ; tr ≤ 2.5 ns; tf≤ 2.5 ns Fig 5. Propagation delay, nBI to nAO Fig 6. nBI to nA (I/O) Fig 7. 5BI to 7BO1 or 6BI to 7BO2 Fig 8. EN1 to nAO or EN2 to nAO Fig 9. EN1 to 5A (I/O) or EN2 to 6A (I/O) 002aab001 VTT 1/3VTT VOH VOL tPLH tPHL 1.5 V1.5 V Vref Vrefinput output 002aab002 VTT 1/3VTT VCC tPLZtPZL Vref Vrefinput output VOL + 0.3 V 1.5 V 002aab003 VTT 1/3VTT VTT VOL tPLH tPHL Vref Vrefinput output VrefVref 002aab004 3.0 V 0 V VOH VOL tPLH tPHL 1.5 V 1.5 Vinput output 1.5 V1.5 V 002aab005 3.0 V 0 V VOH VOL tPLZ tPZL 1.5 V 1.5 Vinput output 1.5 VVOL + 0.3 V

GTL2007_2 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 02 — 16 February 2007 13 of 20 NXP Semiconductors GTL2007 12-bit GTL to LVTTL translator with power good control 13. Test information Fig 10. Load circuit for A outputs Fig 11. Load circuit for B outputs R L = load resistor. C L = load capacitance; includes jig and probe capacitance. R T = termination resistance; should be equal to Zo of pulse generators. Fig 12. Load circuit for open-drain LVTTL I/O PULSE GENERATOR VO C L 50 pF 002aab006 R L

500 WR T

1.5 kW 002aab265 R T VI VCC VCC

GTL2007_2 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 02 — 16 February 2007 14 of 20 NXP Semiconductors GTL2007 12-bit GTL to LVTTL translator with power good control 14. Package outline Fig 13. Package outline SOT361-1 (TSSOP28) UNIT A 1 A 2 A 3 bp cD (1) E (2) (1)eH E LL p QZ ywv q REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.15 0.05 0.95 0.80 0.30 0.19 0.2 0.1 9.8 9.6 4.5 4.3 0.65 6.6 6.2 0.4 0.3 0.8 0.5 o o0.13 0.10.21 DIMENSIONS (mm are the original dimensions) Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 SOT361-1 MO-153 99-12-27 03-02-19 0.25 w M bp Z e 11 4 28 15 pin 1 index q AA 1 A 2 Lp Q detail X L (A )3 H E E c v M A XAD y 0 2.5 5 mm scale TSSOP28: plastic thin shrink small outline package; 28 leads; body width 4.4 mm SOT361-1 A max. 1.1

GTL2007_2 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 02 — 16 February 2007 15 of 20 NXP Semiconductors GTL2007 12-bit GTL to LVTTL translator with power good control 15. Soldering This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application NoteAN10365 “Surface mount reflow soldering description”.

15.1 Introduction to soldering

Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization.

15.2 Wave and reflow soldering

Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following:

  • Through-hole components
  • Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are:
  • Board specifications, including the board finish, solder masks and vias
  • Package footprints, including solder thieves and orientation
  • The moisture sensitivity level of the packages
  • Package placement
  • Inspection and repair
  • Lead-free soldering versus PbSn soldering

15.3 Wave soldering

Key characteristics in wave soldering are:

  • Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave
  • Solder bath specifications, including temperature and impurities

GTL2007_2 © NXP B.V. 2007. All rights reserved.

15.4 Reflow soldering

  • Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (seeFigure14) than a PbSn process, thus reducing the process window
  • Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board
  • Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table14 and15 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, seeFigure14.

Table 14. SnPb eutectic process (from J-STD-020C) Table 15. Lead-free process (from J-STD-020C)

GTL2007_2 © NXP B.V. 2007. All rights reserved. “Surface mount reflow soldering description”. Table 16. Abbreviations

GTL2007_2 © NXP B.V. 2007. All rights reserved. Table 17. Revision history

  • The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors.
  • Legal texts have been adapted to the new company name where appropriate.
  • Data sheet descriptive title changed from “13-bit GTL to LVTTL translator with power good control” to “12-bit GTL to LVTTL translator with power good control”
  • Section 1 “General description”: – 4th paragraph re-written – deleted (old) 5th paragraph
  • Section 2 “Features”: added (new) 2nd bullet item
  • Figure 1 “Logic diagram of GTL2007”: updated symbols to IEC convention
  • Figure 3 “Typical application” modified: – in blocks CPU1 and CPU2, changed “SMI L ” to “DISABLE_L ” – in block PLATFORM HEALTH MANAGEMENT: changed “CPU2 IERR_L ” to “CPU2 1ERR_L ”
  • Table 10 “Limiting values”: parameter definitions updated; addedTable note3 andTable note4
  • Table 13 “Dynamic characteristics”: data reorganized (no specification changed)
  • Table 16 “Abbreviations”: added “DUT” GTL2007_1 (9397 750 13264)

20050602 Product data sheet - -

GTL2007_2 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 02 — 16 February 2007 19 of 20 NXP Semiconductors GTL2007 12-bit GTL to LVTTL translator with power good control 18. Legal information

18.1 Data sheet status

[1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.

18.2 Definitions

Draft —The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet —A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail.

18.3 Disclaimers

General — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes —NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use —NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of a NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications —Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values —Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale —NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license —Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights.

18.4 Trademarks

Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 19. Contact information For additional information, please visit:http://www.nxp.com For sales office addresses, send an email to:salesaddresses@nxp.com Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification.

NXP Semiconductors GTL2007 12-bit GTL to LVTTL translator with power good control © NXP B.V. 2007. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 16 February 2007 Document identifier: GTL2007_2 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. 20. Contents