FG0H104ZF KEMET
Document overview
- PDF pages: 14
Technical content
Page 1
Supercapacitors
FG Series
Overview
FG Series Supercapacitors, also known as Electric Double- Layer Capacitors (EDLCs), are intended for high energy storage applications.
Benefits
- Wide range of temperature from -25°C to +70°C (FG & FGH types) and -40°C to +85°C (FGR type)
- Maintenance free
- 3.5 VDC and 5.5 VDC
- Highly reliable against liquid leakage
- Lead-free and RoHS Compliant
Part Number System
Applications
Supercapacitors have characteristics ranging from traditional capacitors and batteries. As a result, supercapacitors can be used like a secondary battery when applied in a DC circuit. These devices are best suited for use in low voltage DC hold-up applications such as embedded microprocessor systems with flash memory.

| FG | 0H | 104 | Z | F |
| Series | Maximum Operating Voltage | Capacitance Code (F) | Capacitance Tolerance | Environmental |
| FG FGH FGR | 0V = 3.5 VDC 0H = 5.5 VDC | First two digits represent significant figures. Third digit specifies number of zeros. | Z = -20/+80% | F = Lead-free |
One world. One KEMET
Page 2
Dimensions – Millimeters
ø D ± 0.5

d1± 0.1
d2± 0.1
(Terminal)
| Part Number | ø D | H | P | ℓ | d 1 | d 2 |
|---|---|---|---|---|---|---|
| FG0H103ZF | 11.0 | 5.5 | 5.08 | 2.7 | 0.2 | 1.2 |
| FG0H223ZF | 11.0 | 5.5 | 5.08 | 2.7 | 0.2 | 1.2 |
| FG0H473ZF | 11.0 | 5.5 | 5.08 | 2.7 | 0.2 | 1.2 |
| FG0H104ZF | 11.0 | 6.5 | 5.08 | 2.7 | 0.2 | 1.2 |
| FG0H224ZF | 13.0 | 9.0 | 5.08 | 2.2 | 0.4 | 1.2 |
| FG0H474ZF | 14.5 | 18.0 | 5.08 | 2.4 | 0.4 | 1.2 |
| FG0H105ZF | 16.5 | 19.0 | 5.08 | 2.7 | 0.4 | 1.2 |
| FG0H225ZF | 21.5 | 19.0 | 7.62 | 3.0 | 0.6 | 1.2 |
| FG0H475ZF | 28.5 | 22.0 | 10.16 | 6.1 | 0.6 | 1.4 |
| FG0V155ZF | 16.5 | 14.0 | 5.08 | 3.1 | 0.4 | 1.2 |
| FGH0H104ZF | 11.0 | 5.5 | 5.08 | 2.7 | 0.2 | 1.2 |
| FGH0H224ZF | 11.0 | 7.0 | 5.08 | 2.7 | 0.2 | 1.2 |
| FGH0H474ZF | 16.5 | 8.0 | 5.08 | 2.7 | 0.4 | 1.2 |
| FGH0H105ZF | 21.5 | 9.5 | 7.62 | 3.0 | 0.6 | 1.2 |
| FGH0V474ZF | 13.0 | 7.5 | 5.08 | 2.7 | 0.4 | 1.2 |
| FGR0H474ZF | 14.5 | 18.0 | 5.08 | 2.4 | 0.4 | 1.2 |
| FGR0H105ZF | 16.5 | 19.0 | 5.08 | 2.7 | 0.4 | 1.2 |
| FGR0H225ZF | 21.5 | 19.0 | 7.62 | 3.0 | 0.6 | 1.2 |
Page 3
Performance Characteristics
Supercapacitors should not be used for applications such as ripple absorption because of their high internal resistance (several hundred mΩ to a hundred Ω) compared to aluminum electrolytic capacitors. Thus, its main use would be similar to that of secondary battery such as power back-up in DC circuit. The following list shows the characteristics of supercapacitors as compared to aluminum
electrolytic capacitors for power back-up and secondary batteries.
| Secondary Battery | Capacitor | |||
| NiCd | Lithium Ion | Aluminum Electrolytic | Supercapacitor | |
| Back-up ability | – | – | – | – |
| Eco-hazard | Cd | – | – | – |
| Operating Temperature Range | -20 to +60ºC | -20 to +50ºC | -55 to +105ºC | -40 to +85ºC (FR, FT) |
| Charge Time | few hours | few hours | few seconds | few seconds |
| Charge/Discharge Life Time | approximately 500 times | approximately 500 to 1,000 times | limitless (*1) | limitless (*1) |
| Restrictions on Charge/Discharge | yes | yes | none | none |
| Flow Soldering | not applicable | not applicable | applicable | applicable |
| Automatic Mounting | not applicable | not applicable | applicable | applicable (FM and FC series) |
| Safety Risks | leakage, explosion | leakage, combustion, explosion, ignition | heat-up, explosion | gas emission (*2) |
(\*1) Aluminum electrolytic capacitors and supercapacitors have limited lifetime. However, when used under proper conditions, both can operate within a predetermined lifetime. (\*2) There is no harm as it is a mere leak of water vapor which transitioned from water contained in the electrolyte (diluted sulfuric acid). However, application of abnormal voltage surge exceeding maximum operating voltage may result in leakage and explosion.
Typical Applications
| Intended Use (Guideline) | Power Supply (Guideline) | Application | Examples of Equipment | Series |
| Long time back-up | 500 μA and below | CMOS microcomputer, IC for clocks | CMOS microcomputer, static RAM/DTS (digital tuning system) | FG series |
Environmental Compliance
All KEMET supercapacitors are RoHS Compliant.
Page 4
Table 1 – Ratings & Part Number Reference

Part numbers in bold type represent popularly purchased components.
Page 5
Specifications
| Item | FG, FGH Type | FGR Type | Test Conditions (conforming to JIS C 5160-1) | |||
|---|---|---|---|---|---|---|
| Category Temperature Range | -25ºC to +70ºC | -40ºC to +85ºC | ||||
| Maximum Operating Voltage | 5.5 VDC, 3.5 VDC | 5.5 VDC | ||||
| Capacitance | Refer to Table 1 | Refer to Table 1 | Refer to “Measurement Conditions” | |||
| Capacitance Allowance | +80%, -20% | +80%, -20% | Refer to “Measurement Conditions” | |||
| ESR | Refer to Table 1 | Refer to Table 1 | Measured at 1 kHz, 10 mA; See also “Measurement Conditions” | |||
| Current (30 minutes value) | Refer to Table 1 | Refer to Table 1 | Refer to “Measurement Conditions” | |||
| Surge | Capacitance | > 90% of initial ratings | > 90% of initial ratings | Surge voltage: 6.3 V (5.5 V type) 4.0 V (3.5 V type) Charge: 30 seconds Discharge: 9 minutes 30 seconds Number of cycles: 1,000 Series resistance: 0.010 F 1500 Ω 0.022 F 560 Ω 0.047 F 300 Ω 0.10 F 150 Ω 0.22 F 56 Ω 0.47 F 30 Ω 1.0 F, 1.5 F 15 Ω 2.2 F, 4.7 F 10 Ω Discharge resistance: 0 Ω Temperature: 70 ±2ºC (FG, FGH) 85 ±2ºC (FGR) | ||
| ESR | ≤ 120% of initial ratings | ≤ 120% of initial ratings | ||||
| Current (30 minutes value) | ≤ 120% of initial ratings | ≤ 120% of initial ratings | ||||
| Appearance | No obvious abnormality | No obvious abnormality | ||||
| Characteristics in Different Temperature | Capacitance | Phase 2 | ≥ 50% of initial value | Phase 2 | ≥ 50% of initial value | Conforms to 4.17 Phase 1: +25 ±2ºC Phase 2: -25 ±2ºC Phase 3: -40 ±2ºC (FGR) Phase 4: +25 ±2ºC Phase 5: +70 ±2ºC (FG, FGH) +85 ±2ºC (FGR) Phase 6: +25 ±2ºC |
| ESR | ≤ 400% of initial value | ≤ 400% of initial value | ||||
| Capacitance | Phase 3 | Phase 3 | ≥ 30% of initial value | |||
| ESR | ≤ 700% of initial value | |||||
| Capacitance | Phase 5 | ≤ 200% of initial value | Phase 5 | ≤ 200% of initial value | ||
| ESR | Satisfy initial ratings | Satisfy initial ratings | ||||
| Current (30 minutes value) | ≤ 1.5 CV (mA) | ≤ 1.5 CV (mA) | ||||
| Capacitance | Phase 6 | Within ±20% of initial value | Phase 6 | Within ±20% of initial value | ||
| ESR | Satisfy initial ratings | Satisfy initial ratings | ||||
| Current (30 minutes value) | Satisfy initial ratings | Satisfy initial ratings | ||||
| Vibration Resistance | Capacitance | Satisfy initial ratings | Satisfy initial ratings | Conforms to 4.13 Frequency: 10 to 55 Hz Testing Time: 6 hours | ||
| ESR | ||||||
| Current (30 minutes value) | ||||||
| Appearance | No obvious abnormality | No obvious abnormality | ||||
| Solderability | Over 3/4 of the terminal should be covered by the new solder | Over 3/4 of the terminal should be covered by the new solder | Conforms to 4.11 Solder temp: +245 ±5ºC Dipping time: 5 ±0.5 seconds 1.6 mm from the bottom should be dipped. | |||
| Solder Heat Resistance | Capacitance | Satisfy initial ratings | Satisfy initial ratings | Conforms to 4.10 Solder temp: +260 ±10ºC Dipping time: 10 ±1 seconds 1.6 mm from the bottom should be dipped. | ||
| ESR | ||||||
| Current (30 minutes value) | ||||||
| Appearance | No obvious abnormality | No obvious abnormality | ||||
Page 6
Specifications cont’d
| Item | FG, FGH Type | FGR Type | Test Conditions (conforming to JIS C 5160-1) | |
|---|---|---|---|---|
| Temperature Cycle | Capacitance | Satisfy initial ratings | Satisfy initial ratings | Conforms to 4.12 Temperature Condition: Minimum temperature→ Room temperature→ Category maximum temperature→ Room temperature Number of cycles: 5 cycles |
| ESR | ||||
| Current (30 minutes value) | ||||
| Appearance | No obvious abnormality | No obvious abnormality | ||
| High Temperature and High Humidity Resistance | Capacitance | Within ±20% of initial value | Within ±20% of initial value | Conforms to 4.14 Temperature: +40 ±2ºC Relative humidity: 90 to 95% RH Testing time: 240 ±8 hours |
| ESR | ≤ 120% of initial ratings | ≤ 120% of initial ratings | ||
| Current (30 minutes value) | ≤ 120% of initial ratings | ≤ 120% of initial ratings | ||
| Appearance | No obvious abnormality | No obvious abnormality | ||
| High Temperature Load | Capacitance | Within ±30% of initial value | Within ±30% of initial value | Conforms to 4.15 Temperature: Category maximum temperature ±2ºC Voltage applied: Maximum operating voltage Series protection resistance: 0 Ω Testing time: 1,000 +48 (+48/-0) hours |
| ESR | < 200% of initial ratings | < 200% of initial ratings | ||
| Current (30 minutes value) | < 200% of initial ratings | < 200% of initial ratings | ||
| Appearance | No obvious abnormality | No obvious abnormality | ||
| Self Discharge Characteristics (Voltage Holding Characteristics) | 5.5 V type: Voltage between terminal leads > 4.2 V 3.5 V type: Not specified | Voltage between terminal leads > 4.2 V | Charging condition Voltage applied: 5.0 VDC (Terminal at the case side must be negative) Series resistance: 0 Ω Charging time: 24 hours | |
| Storage Let stand for 24 hours in condition described below with terminals opened. Ambient temperature: < 25ºC Relative humidity: < 70% RH | ||||
Marking

number
Page 7
Packaging Quantities
| Part Number | Bulk Quantity per Box |
|---|---|
| FG0H103ZF | 2,000 pieces |
| FG0H223ZF | 2,000 pieces |
| FG0H473ZF | 2,000 pieces |
| FG0H104ZF | 1,600 pieces |
| FG0H224ZF | 800 pieces |
| FG0H474ZF | 300 pieces |
| FG0H105ZF | 240 pieces |
| FG0H225ZF | 90 pieces |
| FG0H475ZF | 50 pieces |
| FG0V155ZF | 160 pieces |
| FGH0H104ZF | 2,000 pieces |
| FGH0H224ZF | 1,600 pieces |
| FGH0H474ZF | 600 pieces |
| FGH0H105ZF | 90 pieces |
| FGH0V474ZF | 800 pieces |
| FGR0H474ZF | 300 pieces |
| FGR0H105ZF | 240 pieces |
| FGR0H225ZF | 90 pieces |
List of Plating & Sleeve Type
By changing the solder plating from leaded solder to lead-free solder and the outer tube material of can-cased conventional supercapacitor from polyvinyl chloride to polyethylene terephthalate (PET), our supercapacitor is now even friendlier to the environment.
a. Iron + copper base + lead-free solder plating (Sn-1Cu) b. SUS nickel base + copper base + reflow lead-free solder plating (100% Sn, reflow processed)
| Series | Part Number | Plating | Sleeve |
|---|---|---|---|
| FG | FG0H103ZF | b | PET (Blue) |
| FG0H223ZF | b | PET (Blue) | |
| FG0H473ZF | b | PET (Blue) | |
| FG0H104ZF | b | PET (Blue) | |
| FG0H224ZF | a | PET (Blue) | |
| FG0H474ZF | a | PET (Blue) | |
| FG0H105ZF | a | PET (Blue) | |
| FG0H225ZF | a | PET (Blue) | |
| FG0H475ZF | a | PET (Blue) | |
| FG0V155ZF | a | PET (Blue) | |
| FGH0H104ZF | b | PET (Blue) | |
| FGH0H224ZF | b | PET (Blue) | |
| FGH0H474ZF | a | PET (Blue) | |
| FGH0H105ZF | a | PET (Blue) | |
| FGH0V474ZF | a | PET (Blue) | |
| All FGR Types | a | PET (Blue) |
Recommended Pb-free solder : Sn / 3.5Ag / 0.75Cu Sn / 3.0Ag / 0.5Cu Sn / 0.7Cu Sn / 2.5Ag / 1.0Bi / 0.5Cu
Page 8
Measurement Conditions
Capacitance (Charge System)
Capacitance is calculated from expression (9) by measuring the charge time constant (τ) of the capacitor (C). Prior to measurement, the capacitor is discharged by shorting both pins of the device for at least 30 minutes. In addition, use the polarity indicator on the device to
determine correct orientation of capacitor for charging.
Eo: 3.0 (V) Product with maximum operating voltage of 3.5 V
τ
Capacitance: C =
(F) (9) Rc
5.0 (V) Product with maximum operating voltage of 5.5 V 6.0 (V) Product with maximum operating voltage of 6.5 V
Switch
10.0 (V) Product with maximum operating voltage of 11 V

12.0 (V) Product with maximum operating voltage of 12 V
τ:
Time from start of charging until Vc becomes 0.632 Eo (V) (seconds)
Rc: See table below (Ω).
Charge Resistor Selection Guide
| Cap | FA | FE | FS | FY | FR | FM, FME FMR, FML | FMC | FG FGR | FGH | FT | FC, FCS | HV | ||
| FYD | FYH | FYL | ||||||||||||
| 0.010 F | – | – | – | – | – | 5000 Ω | – | 5000 Ω | – | 5000 Ω | – | – | – | – |
| 0.022 F | 1000 Ω | – | 1000 Ω | 2000 Ω | 2000 Ω | 2000 Ω | 2000 Ω | 2000 Ω | – | 2000 Ω | – | – | Discharge | – |
| 0.033 F | – | – | – | – | – | – | – | Discharge | – | – | – | – | – | – |
| 0.047 F | 1000 Ω | 1000 Ω | 1000 Ω | 2000 Ω | 1000 Ω | 2000 Ω | 1000 Ω | 2000 Ω | 1000 Ω | 2000 Ω | – | – | – | – |
| 0.10 F | 510 Ω | 510 Ω | 510 Ω | 1000 Ω | 510 Ω | – | 1000 Ω | 1000 Ω | 1000 Ω | 1000 Ω | Discharge | 510 Ω | Discharge | – |
| 0.22 F | 200 Ω | 200 Ω | 200 Ω | 510 Ω | 510 Ω | – | 510 Ω | 0H: Discharge 0V: 1000 Ω | – | 1000 Ω | Discharge | 200 Ω | Discharge | – |
| 0.33 F | – | – | – | – | – | – | – | – | Discharge | – | – | – | – | – |
| 0.47 F | 100 Ω | 100 Ω | 100 Ω | 200 Ω | 200 Ω | – | 200 Ω | – | – | 1000 Ω | Discharge | 100 Ω | Discharge | – |
| 1.0 F | 51 Ω | 51 Ω | 100 Ω | 100 Ω | 100 Ω | – | 100 Ω | – | – | 510 Ω | Discharge | 100 Ω | Discharge | Discharge |
| 1.4 F | – | – | – | 200 Ω | – | – | – | – | – | – | – | – | – | – |
| 1.5 F | – | 51 Ω | – | – | – | – | – | – | – | 510 Ω | – | – | – | – |
| 2.2 F | – | – | – | 100 Ω | – | – | – | – | – | 200 Ω | – | 51 Ω | – | – |
| 2.7 F | – | – | – | – | – | – | – | – | – | – | – | – | – | Discharge |
| 3.3 F | – | – | – | – | – | – | – | – | – | – | – | 51 Ω | – | – |
| 4.7 F | – | – | – | – | – | – | – | – | – | 100 Ω | – | – | – | Discharge |
| 5.0 F | – | – | 100 Ω | – | – | – | – | – | – | – | – | – | – | – |
| 5.6 F | – | – | – | – | – | – | – | – | – | – | – | 20 Ω | – | – |
| 10.0 F | – | – | – | – | – | – | – | – | – | – | – | – | – | Discharge |
| 22.0 F | – | – | – | – | – | – | – | – | – | – | – | – | – | Discharge |
| 50.0 F | – | – | – | – | – | – | – | – | – | – | – | – | – | Discharge |
| 100.0 F | – | – | – | – | – | – | – | – | – | – | – | – | – | Discharge |
| 200.0 F | – | – | – | – | – | – | – | – | – | – | – | – | – | Discharge |
\*Capacitance values according to the constant current discharge method. \*HV Series capacitance is measured by discharge system
Page 9
51 Ω
3.3F – – – – – – – – – – –
–
100 Ω
4.7F – – – – – – – – –
– – –
100 Ω
5.0F – –
– – – – – – – – – – 20 Ω
5.6F – – – – – – – – – – –
–
\*Capacitance values according to the constant current discharge method. \*HV series capacitance is measured by discharge system.
Table 3 Capacitance measurement
Measurement Conditions cont’d
Capacitance (Discharge System)
In the diagram below, charging is performed for a duration of 30 minutes, once the voltage of the condensor terminal
Capacitance (Discharge System)
Capacitance (Discharge System:3.5V)
As shown in the diagram below, charging is performed for a duration of 30 minutes once the voltage of the capacitor terminal reaches reaches 5.5 V. In the diagram below, charging is performed for a duration of 30 minutes, once the voltage of the capacitor terminal reaches 3.5V.
5.5 V. Then, use a constant current load device and measure the time for the terminal voltage to drop from 3.0 to 2.5 V upon discharge Then, use a constant current load device and measure the time for the terminal voltage to drop from 3.0 to 2.5 V upon Then, use a constant current load device and measure the time for the terminal voltage to drop from 1.8 to 1.5V upon
at 0.22 mA per 0.22 F, for example, and calculate the static capacitance according to the equation shown below.
discharge at 0.22 mA for 0.22 F, for example, and calculate the static capacitance according to the equation shown below. discharge at 1 mA per 1F, and calculate the static capacitance according to the equation shown below.
Note: The current value is 1 mA discharged per 1 F. Note: The current value is 1 mA discharged per 1F.

(V) 0.22mA(I)

I×(T2-T1) I×(T2-T1)
C= (F) Capactance:C= (F) V1-V2 V1-V2
30 minutes
Capacitance (Discharge System:3.5V)
Capacitance (Discharge System:3.5V)
Capacitance (Discharge System – 3.5 V)
Capacitance (Discharge System:3.5V)
Capacitance (Discharge System:3.5V)
Capacitance (Discharge System:3.5V)
Capacitance (Discharge System:HVseries)
36 Super Capacitors Vol.13 As shown in the diagram below, charging is performed for a duration of 30 minutes once the voltage of the capacitor terminal reaches
In the diagram below, charging is performed for a duration of 30 minutes, once the voltage of the capacitor terminal reaches In the diagram below, charging is performed for a duration of 30 minutes, once the voltage of the capacitor terminal reaches 3.5V. In the diagram below, charging is performed for a duration of 30 minutes, once the voltage of the capacitor terminal reaches In the diagram below, charging is performed for a duration of 30 minutes, once the voltage of the capacitor terminal reaches 3.5V. In the diagram below, charging is performed for a duration of 30 minutes, once the voltage of the capacitor terminal reaches 3.5V. In the diagram below, charging is performed for a duration of 30 minutes, once the voltage of the capacitor terminal reaches
3.5 V. Then, use a constant current load device and measure the time for the terminal voltage to drop from 1.8 to 1.5 V upon discharge
Then, use a constant current load device and measure the time for the terminal voltage to drop from 1.8 to 1.5V Then, use a constant current load device and measure the time for the terminal voltage to drop from 1.8 to 1.5V upon Then, use a constant current load device and measure the time for the terminal voltage to drop from 1.8 to 1.5V Then, use a constant current load device and measure the time for the terminal voltage to drop from 1.8 to 1.5V upon Then, use a constant current load device and measure the time for the terminal voltage to drop from 1.8 to 1.5V upon Max. operating voltage. discharge at 1 mA per 1F, and calculate the static capacitance according to the equation shown below.
at 1.0 mA per 1.0 F, for example, and calculate the static capacitance according to the equation shown below.
discharge at 1 mA per 1F, and calculate the static capacitance according to the equation shown below. discharge at 1 mA per 1F, and calculate the static capacitance according to the equation shown below. discharge at 1 mA per 1F, and calculate the static capacitance according to the equation shown below. discharge at 1 mA per 1F, and calculate the static capacitance according to the equation shown below. Then, use a constant current load device and measure the time for the terminal voltage to drop from 2.0 to 1.5V upon discharge
(V) (V)
at 1 mA per 1F, and calculate the static capacitance according to the equation shown below.

(V)

I×(T2-T1) I×(T2-T1) I×(T2-T1) I×(T2-T1) C= (F) C= (F) I×(T2-T1) C= (F) C= (F)
V1-V2 V1-V2 C= (F)
V1-V2 V1-V2 I×(T2-T1) V1-V2 C= (F) V1-V2
30 minutes T1 T2 Time (sec.)
Capacitance (Discharge System:HVseries)
Capacitance (Discharge System:HVseries)
Capacitance (Discharge System:HVseries)
Capacitance (Discharge System:HVseries)
30 minutes
Capacitance (Discharge System – HV Series)
Capacitance (Discharge System:HVseries)
In the diagram below, charging is performed for a duration of 30 minutes, once the voltage of the capacitor terminal re In the diagram below, charging is performed for a duration of 30 minutes, once the voltage of the capacitor terminal reaches In the diagram below, charging is performed for a duration of 30 minutes, once the voltage of the capacitor terminal re
As shown in the diagram below, charging is performed for a duration of 30 minutes once the voltage of the capacitor terminal reaches
In the diagram below, charging is performed for a duration of 30 minutes, once the voltage of the capacitor terminal reaches
Equivalent series resistance (ESR)
In the diagram below, charging is performed for a duration of 30 minutes, once the voltage of the capacitor terminal reaches Max. operating voltage. Max. operating voltage. Max. operating voltage.
maximum operating voltage. Then, use a constant current load device and measure the time for the terminal voltage to drop from 2.0 to
Max. operating voltage. Max. operating voltage. ESR shall be calculated from the equation below. Then, use a constant current load device and measure the time for the terminal voltage to drop from 2.0 to 1.5V upon disc Then, use a constant current load device and measure the time for the terminal voltage to drop from 2.0 to 1.5V upon discharge Then, use a constant current load device and measure the time for the terminal voltage to drop from 2.0 to 1.5V upon disc Then, use a constant current load device and measure the time for the terminal voltage to drop from 2.0 to 1.5V upon discharge
1.5 V upon discharge at 1.0 mA per 1.0 F, and calculate the static capacitance according to the equation shown below.
Then, use a constant current load device and measure the time for the terminal voltage to drop from 2.0 to 1.5V upon discharge at 1 mA per 1F, and calculate the static capacitance according to the equation shown below. at 1 mA per 1F, and calculate the static capacitance according to the equation shown below. at 1 mA per 1F, and calculate the static capacitance according to the equation shown below. at 1 mA per 1F, and calculate the static capacitance according to the equation shown below. at 1 mA per 1F, and calculate the static capacitance according to the equation shown below.
10mA

VC

ESR= (Ω) 0.01 I×(T2-T1) I×(T2-T1) I×(T2-T1) I×(T2-T1) C= (F) C= (F) I×(T2-T1) C= (F) C= (F)
V1-V2 V1-V2 C= (F)
V1-V2 V1-V2 V1-V2
Current (at 30 minutes after charging)
Current shall be calculated from the equation below. Prior to measurement, both lead terminals must be short-circuited for a minimum of 30 minutes.
30 minutes 30 minutes 30 minutes
Equivalent series resistance (ESR)
Equivalent series resistance (ESR)
The lead terminal connected to the metal can case is connected to the negative side of the power supply.
Equivalent series resistance (ESR)
Equivalent Series Resistance (ESR)
Equivalent series resistance (ESR)
Equivalent series resistance (ESR)
ESR shall be calculated from the equation below.
ESR shall be calculated from the equation below. ESR shall be calculated from the equation below. ESR shall be calculated from the equation below. ESR shall be calculated from the equation below. Eo: 2.5Vdc (HVseries 50F) ESR shall be calculated from the equation below.

2.7Vdc (HVseries except 50F)
SW
VC VC 3.0Vdc (3.5V type)
VC ESR= (Ω) ESR= (Ω) VC ESR= (Ω) VC ESR= (Ω)
0.01
ESR= (Ω) 0.01 5.0Vdc (5.5V type)
0.01
+
0.01 0.01 Rc: 1000Ω (0.010F, 0.022F, 0.047F)
C -
100Ω (0.10F, 0.22F, 0.47F) 10Ω (1.0F, 1.5F, 2.2F, 4.7F)
Current (at 30 minutes after charging)
Current (at 30 minutes after charging)
Current (at 30 minutes after charging)
Current (at 30 minutes after charging)
2.2Ω (HVseries)
Current (at 30 minutes after charging)
Current shall be calculated from the equation below. Current shall be calculated from the equation below. Current shall be calculated from the equation below. VR
Current shall be calculated from the equation below. Current shall be calculated from the equation below. Current= (A) Prior to measurement, both lead terminals must be short-circuited for a minimum of 30 minutes. Prior to measurement, both lead terminals must be short-circuited for a minimum of 30 minutes. Prior to measurement, both lead terminals must be short-circuited for a minimum of 30 minutes. Prior to measurement, both lead terminals must be short-circuited for a minimum of 30 minutes.
RC
Prior to measurement, both lead terminals must be short-circuited for a minimum of 30 minutes. The lead terminal connected to the metal can case is connected to the negative side of the power supply. The lead terminal connected to the metal can case is connected to the negative side of the power supply. The lead terminal connected to the metal can case is connected to the negative side of the power supply. The lead terminal connected to the metal can case is connected to the negative side of the power supply. The lead terminal connected to the metal can case is connected to the negative side of the power supply.
Self-discharge characteristic (0H: 5.5V products)
Eo: 2.5Vdc (HVseries 50F) Eo: 2.5Vdc (HVseries 50F) Eo: 2.5Vdc (HVseries 50F) Eo: 2.5Vdc (HVseries 50F) The self-discharge characteristic is measured by charging a voltage of 5 0 Vdc (charge protection resistance: 0Ω) according Eo:2 5Vdc (HVseries 50F)
VR VR
2 7Vdc (HVse ies e cept 50F) 2 7Vd (HV i
t 50F)
V
Page 10
ESR shall be calculated from the equation below.
Current (at 30 minutes after charging)
10mA
VC Current shall be calculated from the equation below.
ESR= (Ω)
f:1kHz
C
VC
0.01 Prior to measurement, both lead terminals must be short-circuited for a minimum of 30 minute The lead terminal connected to the metal can case is connected to the negative side of the po
Measurement Conditions cont’d
Eo: 2.5Vdc (HVseries 50F)
Current (at 30 minutes after charging)
VR
2.7Vdc (HVseries except 50F)
SW
Current shall be calculated from the equation below.
Current (at 30 minutes after charging)
3.0Vdc (3.5V type)
Prior to measurement, both lead terminals must be short-circuited for a minimum of 30 minutes.
Current shall be calculated from the equation below. Prior to measurement, both lead terminals must be short-circuited for a minimum
RC
5.0Vdc (5.5V type)
The lead terminal connected to the metal can case is connected to the negative side of the power supply.
+
of 30 minutes. The lead terminal connected to the metal can case is connected to the negative side of the power supply.
Rc: 1000Ω (0.010F, 0.022F, 0.047F)
EO
C
100Ω (0.10F, 0.22F, 0.47F)
-
Eo: 2.5Vdc (HVseries 50F)

10Ω (1.0F, 1.5F, 2.2F, 4.7F)
Eo: 2.5 VDC (HV Series 50 F)
2.7Vdc (HVseries except 50F)
2.7 VDC (HV Series except 50 F)
2.2Ω (HVseries)
3.0 VDC (3.5 V type)
3.0Vdc (3.5V type)
VR
5.0 VDC (5.5 V type)
Current= (A) 5.0Vdc (5.5V type)
Rc: 1000 Ω (0.010 F, 0.022 F, 0.047 F)
Rc: 1000Ω (0.010F, 0.022F, 0.047F)
RC
100 Ω (0.10 F, 0.22 F, 0.47 F)
-
100Ω (0.10F, 0.22F, 0.47F)
10 Ω (1.0 F, 1.5 F, 2.2 F, 4.7 F)
Self-discharge characteristic (0H: 5.5V products)
10Ω (1.0F, 1.5F, 2.2F, 4.7F)
2.2 Ω (HV Series)
2.2Ω (HVseries) The self-discharge characteristic is measured by charging a voltage of 5.0 Vdc (charge protec to the capacitor polarity for 24 hours, then releasing between the pins for 24 hours and measu VR
Self-Discharge Characteristic (0H – 5.5 V Products)
Current= (A)
The test should be carried out in an environment with an ambient temperature of 25℃ or belo
The self-discharge characteristic is measured by charging a voltage of 5.0 VDC (charge protection resistance: 0 Ω) according to the
RC RH or below.
capacitor polarity for 24 hours, then releasing between the pins for 24 hours and measuring the pin-to-pin voltage. The test should be
Self-discharge characteristic (0H: 5.5V products)
carried out in an environment with an ambient temperature of 25° C or below and relative humidity of 70% RH or below.
Su
The self-discharge characteristic is measured by charging a voltage of 5.0 Vdc (charge protection resistance
the soldering is checked.
to the capacitor polarity for 24 hours, then releasing between the pins for 24 hours and measuring the pin-to- The test should be carried out in an environment with an ambient temperature of 25℃ or below and relative
4. Dismantling
RH or below.
There is a small amount of electrolyte stored within the capacitor. Do not attempt to dismantle as direct skin contact with the electrolyte
will cause burning. This product should be treated as industrial waste and not is not to be disposed of by fire.
Super Capacito
Page 11
Notes on Using Supercapacitors or Electric Double-Layer Capacitors (EDLCs)
- Circuitry Design 1.1 Useful life The FC Series Supercapacitor (EDLC) uses an electrolyte in a sealed container. Water in the electrolyte can evaporate while in use over long periods of time at high temperatures, thus reducing electrostatic capacity which in turn will create greater internal resistance. The characteristics of the supercapacitor can vary greatly depending on the environment in which it is used. Basic breakdown mode is an open mode due to increased internal resistance.
1.2 Fail rate in the field Based on field data, the fail rate is calculated at approximately 0.006 Fit. We estimate that unreported failures are ten times this amount. Therefore, we assume that the fail rate is below 0.06 Fit.
1.3 Exceeding maximum usable voltage Performance may be compromised and in some cases leakage or damage may occur if applied voltage exceeds maximum working voltage.
1.4 Use of capacitor as a smoothing capacitor (ripple absorption) As supercapacitors contain a high level of internal resistance, they are not recommended for use as smoothing capacitors in electrical circuits. Performance may be compromised and, in some cases, leakage or damage may occur if a supercapacitor is used in ripple absorption.
1.5 Series connections As applied voltage balance to each supercapacitor is lost when used in series connection, excess voltage may be applied to some supercapacitors, which will not only negatively affect its performance but may also cause leakage and/or damage. Allow ample margin for maximum voltage or attach a circuit for applying equal voltage to each supercapacitor (partial pressure resistor/voltage divider) when using supercapacitors in series connection. Also, arrange supercapacitors so that the temperature between each capacitor will not vary.
1.6 Case Polarity The supercapacitor is manufactured so that the terminal on the outer case is negative (-). Align the (-) symbol during use. Even though discharging has been carried out prior to shipping, any residual electrical charge may negatively affect other parts.
1.7 Use next to heat emitters Useful life of the supercapacitor will be significantly affected if used near heat emitting items (coils, power transistors and posistors, etc.) where the supercapacitor itself may become heated.
1.8 Usage environment This device cannot be used in any acidic, alkaline or similar type of environment.
Page 12
Notes on Using Supercapacitors or Electric Double-Layer Capacitors (EDLCs) cont’d
- Mounting 2.1 Mounting onto a reflow furnace Except for the FC series, it is not possible to mount this capacitor onto an IR / VPS reflow furnace. Do not immerse the capacitor into a soldering dip tank.
2.2 Flow soldering conditions See Recommended Reflow Curves in Section – Precautions for Use
2.3 Installation using a soldering iron Care must be taken to prevent the soldering iron from touching other parts when soldering. Keep the tip of the soldering iron under 400ºC and soldering time to within 3 seconds. Always make sure that the temperature of the tip is controlled. Internal capacitor resistance is likely to increase if the terminals are overheated.
2.4 Lead terminal processing Do not attempt to bend or polish the capacitor terminals with sand paper, etc. Soldering may not be possible if the metallic plating is removed from the top of the terminals.
2.5 Cleaning, Coating, and Potting Except for the FM series, cleaning, coating and potting must not be carried out. Consult KEMET if this type of procedure is necessary. Terminals should be dried at less than the maximum operating temperature after cleaning.
- Storage 3.1 Temperature and humidity Make sure that the supercapacitor is stored according to the following conditions: Temperature: 5 – 35ºC (Standard 25ºC), Humidity: 20 – 70% (Standard: 50%). Do not allow the build up of condensation through sudden temperature change.
3.2 Environment conditions Make sure there are no corrosive gasses such as sulfur dioxide, as penetration of the lead terminals is possible. Always store this item in an area with low dust and dirt levels. Make sure that the packaging will not be deformed through heavy loading, movement and/or knocks. Keep out of direct sunlight and away from radiation, static electricity and magnetic fields.
3.3 Maximum storage period This item may be stored up to one year from the date of delivery if stored at the conditions stated above.
Page 13
KEMET Corporation
Europe
World Headquarters
Southern Europe Paris, France
2835 KEMET Way
Tel: 33-1-4646-1006
Simpsonville, SC 29681
Sasso Marconi, Italy
Mailing Address:
Tel: 39-051-939111
P.O. Box 5928 Greenville, SC 29606
Central Europe
www.kemet.com
Landsberg, Germany
Tel: 864-963-6300
Tel: 49-8191-3350800
Fax: 864-963-6521
Kamen, Germany
Corporate Offi ces
Tel: 49-2307-438110
Fort Lauderdale, FL Tel: 954-766-2800
Northern Europe
North America
Bishop’s Stortford, United Kingdom Tel: 44-1279-460122
Southeast Lake Mary, FL
Espoo, Finland
Tel: 407-855-8886
Tel: 358-9-5406-5000
Northeast Wilmington, MA Tel: 978-658-1663
Central Novi, MI Tel: 248-306-9353
West Milpitas, CA Tel: 408-433-9950
Mexico Guadalajara, Jalisco Tel: 52-33-3123-2141
Asia
Northeast Asia Hong Kong Tel: 852-2305-1168
Shenzhen, China Tel: 86-755-2518-1306
Beijing, China Tel: 86-10-5829-1711
Shanghai, China Tel: 86-21-6447-0707
Taipei, Taiwan Tel: 886-2-27528585
Southeast Asia Singapore Tel: 65-6586-1900
Penang, Malaysia Tel: 60-4-6430200
Bangalore, India Tel: 91-806-53-76817
Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of KEMET Electronics Corporation.
Page 14
Disclaimer
This product has been made available through a Private Label Agreement and a Development and Cross-Licensing Agreement between KEMET and NEC TOKIN to expand market and product offerings for both companies and their respective customers. For more information, please visit http://www.kemet.com/nectokin.
All product specifi cations, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed.
All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.
Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are not intended to constitute – and KEMET specifi cally disclaims – any warranty concerning suitability for a specifi c customer application or use. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained.
Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage.
Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not be required.