F32 NICHICON
Document overview
- PDF pages: 1
Technical content
Page 1
CONDUCTIVE POLYMER TANTALUM SOLID ELECTROLYTIC CAPACITORS
F32
Conductive Polymer
Resin-molded Chip
Adapted to the RoHS directive (2002/95/EC).

Type numbering system (Example : 6.3V 100µF)

Dimensions
A • B Case
C • N Case

| Case code | L | W1 | W2 | H | S |
| A | 3.2±0.2 | 1.6±0.2 1. | 2±0.1 | 1.6±0.2 | 0.8±0.2 |
| B | 3.5±0.2 | 2.8±0.2 2. | 2±0.1 | 1.9±0.2 | 0.8±0.2 |
| C | 6.0±0.2 | 3.2±0.2 2. | 2±0.1 | 2.5±0.2 | 1.3±0.2 |
| N | 7.3±0.2 | 4.3±0.2 2. | 4±0.1 | 2.8±0.2 | 1.3±0.2 |
Marking
A Case
B Case Rated Capacitance ( F)
µ
Capacitance code
68
Jar
P6v Month code

Conductive Polymer
Standard ratings

Specifications
| Item | Performance Characteristics |
| Category Temperature Range | Ð55 to +105ûC (Rated temperature + 85ûC) |
| Capacitance Tolerance | ±20% (120Hz) |
| Dissipation Factor(at 120Hz) | Refer to the list below |
| ESR (100kHz) | Refer to the list below |
| Leakage Current | After 5 minutes' application of rated voltage, leakage current at 20ûC is not more than 0.1CV |
| Ripple Current | Refer to the list below |
| Damp Heat (Steady State) | At 60ûC, 90 to 95% R.H. 500hours (No voltage applied) |
| Capacitance Change..Within Ð20 to +30% of initial value Dissipation Factor.......1.5 times Initial specified value or less Leakage Current.........Initial specified value or less | |
| Temperature Cycles | Ð55ûC / +105ûC 30 minutes each 5 cycle |
| Capacitance Change..Within ±20% of initial value Dissipation Factor.......Initial specified value or less Leakage Current.........Initial specified value or less | |
| Resistance to Soldering Heat | Test Condition;10 second reflow at 240ûC |
| Capacitance Change..Within ±20% of initial value Dissipation Factor.......1.3 times Initial specified value or less Leakage Current.........Initial specified value or less | |
| Surge | After application of surge voltage in series with a 1k½ resistor at the rate of 30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85ûC, capacitors meet the characteristics requirements listed below. Capacitance Change...Within ±20% of initial value Dissipation Factor........Initial specified value or less Leakage Current..........Initial specified value or less |
| Endurance 1 | After 1000 hours' application of rated voltage in series with a 3½ resistor at 85ûC. Capacitance Change....Within ±20% of initial value Dissipation Factor...1.5 times Initial specified value or less Leakage Current...Initial specified value or less |
| Endurance 2 | After 1000 hours' application of rated voltage in series with a 3½ resistor at 105ûC,capacitors meet the characteristic requirements listed below Capacitance Change....Within ±20% of initial value Dissipation Factor...3 times Initial specified value or less Leakage Current...Initial specified value or less |
| Shear Test | After applying the pressure load of 5N for 10±1 seconds horizontally to the center of capacitor side body which has no electrode and has been soldered beforehand on an aluminum substrate, there shall be found neither exfoliation nor its sign at the 5N (0.51kg ¥ f) terminal electrode. For 10±1 seconds |
| Terminal Strength | Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of the capacitor, the pressure strength is applied with a specified jig at the center of the R230 20 substrate so that the substrate may bend by 1mm as illustrated. Then, 1mm there shall be found no remarkable 45 45 abnormality on the capacitor terminals. |
∗ As for the surge voltage refer to page 301 for details.
Standard ratings

( ) ESR specification types are also available upon request.
CAT.8100X
Please contact to your local Nichicon sales office when these series are being designed in your application.