DATASHEET SEARCH SITE

Document overview

  • PDF pages: 7

Technical content

Page 1

EV6R11

IX6R11 HALF BRIDGE DRIVER Evaluation Board

Features

  • Single chip for driving high/low side MOSFETs / IGBTs
  • High to low side isolation of 600V
  • Common-mode dv/dt immunity of greater than 50V/nanosecond
  • Undervoltage lockout
  • Optimized power circuit layout
  • High side bootstrap supply
  • Sockets for freewheeling fast recovery diodes

(FREDS)

  • Flexibility of power level utilization
  • 5V compatible HCMOS input logic with hysterisis
  • Protection from cross conduction of the half bridge
  • Simple, fast and low cost means of evaluation and design
  • Option for using IXDP630 with RC oscillator or IXDP631 with crystal oscillator for improved dead time accuracy.
  • Three phase operation with the ability to attach additional slave driver boards.

Introduction

The EV6R11 KIT implements a single power phase-leg circuit on a double-sided PCB, using the ISOSMARTTM HALF BRIDGE DRIVER CHIPSET - IX6R11and IXDP630 dead time generator. This evaluation board includes an assembled and tested PCB with two power devices. Just follow the instructions in this document and connect the board to the load and power.

Any power circuit is layout sensitive. The layout of this PCB is a proven, working layout. The designer is invited to duplicate this layout in his system, following the evaluation of the driver chipset.

Most systems vary in their power level requirements and therefore the power devices used. Due to this fact and fluctuations in availability of power devices, the kit will not always include the same power devices. The designer is encouraged to use the power devices that are required for his system. The devices that are enclosed serve only for initial evaluation.

PDF page 1 diagram

Figure 1: EV6R11 Assembled PCB With S3 Package

Copyright © IXYS CORPORATION 2003

First Release

Page 2

Schematic Diagram:

P1 pins P1-1 GND

P1-9 N/C

PDF page 2 diagram

Figure 3: EV6R11 PCB Schematic

Schematic Notes:

This is a demonstration PCB and has been designed for flexibility and ease of use. The

schematic shows all options but does not mean the PCB is configured as such when ordered. The PCB will be loaded with either the IX6R11S3 16 pin SOIC package (U3) OR the IX6R11S6 18 pin

SOIC package with heat sink tab (U4). The free-wheeling diodes, D2 and D3, are also not included but can be installed if IGBTs are used.

Ordering:

EV6R11S3 PCB with IX6R11S3 16 pin SOIC IC package
EV6R11S6 PCB with IX6R11S6 18 pin SOIC IC package with heat tab

Page 3

ASSEMBLY:

Figure 3 is a complete schematic diagram of the design kit. This schematic indicates an application using MOSFETs. When IGBTs are used, freewheeling diodes (D2&D3) are typically added.

To operate the PCB, simply solder the included MOSFET power devices and C9 or install de- vices specific to your application. Note gate drain source pin orientation of power devices when installing on the PCB. C9 has not been installed due to its high profile and possible lead damage.

NOTES:

a) The ICs and Power devices are static sensitive and require special handling.

b) Use any power device that is suitable for your application. The PCB was designed to accept devices with TO-247 or TO-264 packages. Two IXYS power devices are included in the kit. D2 and D3 are required only if Q1 and Q2 are IGBTs, and thus are not included in the kit. (A recommendation for D2 & D3 is in the Bill of Materials). c) Use any convenient method of interconnection at LS_GND, Q1-D, Q2-S, DC_BUS. The hole spacing is 5.08mm and will fit most common terminal blocks. (A recommendation for a connector that the PCB will accept is in the Bill of Materials and is available from Digi-Key among other sources).

d) For half bridge applications, insert a jumper between Q1-D and Q2-S. e) The gate resistors, R1 and R2, will depend on the power device size that is used. 5.11 Ohm resistors are installed and should work for most applications.

f) IXDP630 dead time is provided by timing components R3 and C5 and is fixed at roughly 1 microsecond. See the IXDP630 data sheet for calculation and modification of the dead time value. It must also be noted that dead time starts to impact drive signals as drive frequency goes

up. Jitter is then produced as drive signal 'On' time overlaps into dead time. A practical limit in values are soon reached with timing components R3 and C5 as they are adjusted to compensate for the reduced period in drive frequency. It is possible to 'overdrive' the IXDP630 with an external clock signal applied to pin 10 to reduce dead time even further than what is possible with R3 and C5. To do this, remove R3, C5 from the board and install a 50 Ohm load resistor at position R10. Solder pads have been provided at R10 to solder the ends of a coax cable directly to the board. The IXDP630 can be driven in excess of 50MHz.

g) The IXDP630 dead time generator is a 5V HCMOS device. The addition of the IXDP630 on the evaluation board is in part for convenience in providing dual complementary drive signals. The IXDP631 is a performance extension of the IXDP630 and can be added as desired by the user. However there is no part number available for a IXDP631 loaded evaluation board and the user must request IXDP631 samples separately. Please note that threshold levels must be ob- served when selecting the front end logic Vdd supply voltage. To increase threshold level flexibility, this PCB incorporates a level translation circuit with Q3 and Q4. As configured, a three terminal +5V regulator, U1, supplies power to

the IXDP630 and translator circuit which implies that Vdd should be greater than 8V to prevent regulator drop-out. Please note that this is only one way to configure the board and was chosen to provide a fast, easy way to get started during the design stage.

Page 4

DATA SHEETS:

The following list provides direct web links for the IXYS devices included with this PCB.

Please visit the IXYS web site at www.ixys.com for a complete overview of the entire IXYS product line.

IX6R11 Half Bridge Driver IC: http://www.ixys.com/99037.pdf

IXDP630 Digital Dead Time Generator: http://www.ixys.com/98568.pdf

IXFH 7N90Q Power MOSFETS: http://www.ixys.com/98645.pdf

Bill of Materials

Reference Qty. Description

Mfr.

Part #

U1

1 +5V regulator

National Semi.

LM78L05ACZ

U2

1 Dead time generator IC

IXYS

IXDP630

U3

1 16 pin Half Bridge Driver

IXYS

IX6R11S3

U4

1 18 pin Half bridge Driver

IXYS

IX6R11S6

D1

1 1A, 1000V high speed diode

Diodes Inc.

UF1007DICT

U2

1 18 pin socket

Assmann

A18-LC-TT

Q1, 2

2 High voltage power MOSFET

IXYS

IXFH7N90Q

Q3, 4

2 Switching MOSFET

Motorola

2N7000

R1, 2

2 5.11 ohm, 1/4 W resistors

R4, 5, 6

3 10k ohm, 1/4 W resistors

R3, 7, 8

3 1k ohm, 1/4 W resistors

R9

1 10 ohm, 1/4 W resistors

R11, 12

2 4.02k ohm 1/4 W resistors

R13, 15

2 Insulated wire jumpers

C1,7,10

3 10uF, 35V, aluminum electrolytic cap

Panasonic

C2,4,8,11,12,13 6

0.1uF, 50V, ceramic cap

Panasonic

C3

1 0.01uF, 50V, ceramic cap

C5

1 27pF, 50V, ceramic cap

Panasonic

C9

1 0.1uF, 1000V, ceramic cap

Sprague

10GAP10

Berg

P1

1 13 pin header connector

68000-236

NOT INCLUDED: U2

1 Crystal based dead time generator

IXYS

IXDP631

D4, D5

2 12A, 1000V fast recovery diode

IXYS

DSEI12-10A

P2

1 4 pole terminal block

Altech Corp.

AKZ250/4

R3

1 1M ohm, 1/4 W IXDP631 osc load resistor

R10

1 50 ohm, 1/4 W load resistor

C5, 6

2 Crystal load capacitors, 22pF 50V ceramic

Panasonic

Y1

1 Crystal for IXDP631 operation

Pletronics

Page 5

OPERATION:

For performance evaluation and power system design please note the following:

a) The assembled board can be run with the IXDP630 removed by applying complementary 5V square waves with proper "dead time" to the input pins HIN (P1-2) and LIN (P1-3). For standard IXDP630 operation, the values of R3 and C5 have been listed on the bill of materials. These values are for demonstration, which may not be appropriate for your application and can be changed as needed. For IXDP631 operation, load R3, C5, C6 with the recommended load components as outlined in the IXDP630/631 data sheet along with the crystal at the frequency of choice. R3 and C5 serve a dual purpose depending on which dead timer is used. The IXDP630 is hardwired for phase 'R' operation, see 630/631 data sheet, with pins

OUTENA, ENAR, and RESET tied high. PWM drive input signal for ' R' phase is ap- plied to P1-6. To add phases 'S' and/or 'T', enable phases with jumpers at JP1 and/or JP2 and apply PWM phase drive signals to TP5 and/or TP6 taking the respective complementary outputs from TP1 through TP4. Note that TP1- TP6 are through-hole pads that have been added to the board to serve as convenient solder and/or test points. b) The IX6R11 provides a wide range of flexibility with its power supply requirements. However, threshold levels must be observed in the relationship between Vdd to HIN and LIN when selecting power supply values in the final design. Device propagation delays

can also be minimized by observing relative values between supplies. c) Be careful with ground connections. Avoid ground loops. In general, connect the grounds as shown in Figure 4 to minimize ground bounce effects. This is particularly important when three "High/Low side driver design kits" are connected together with a single IXDP630

to form a three phase drive system, such as that shown in Figure 5. d) Before using the PCB at full power or at- tempting a short circuit test, make sure that a proper high voltage electrolytic capacitor is connected between DC BUS and GND as shown in Figure 4. The leads to this capacitor should be as short as possible to minimize any stray inductance. e) Figure 4 shows the load terminated at point A. This point could be connected to a number of places depending on the application. For example: Connection to ground will test the high side device. Connection to DC BUS will test the low side device. It could also be connected to the center point of a capacitive

divider (UPS systems). f) Figure 5 shows a three phase power system implementation with a load configured in a Y (star). It could also be configured in a DELTA configuration. Please note the grounding scheme. Cut the connection between "ground plane 2" and "ground plane 4" on the components side of the PCB and solder a 10 Ohm resistor between these ground planes. The GND of each board is terminated to a single ground point.

Page 6

PDF page 6 diagram

Figure 4: Evaluation Board & Load Termination

Vdd Vcl

PDF page 6 diagram

R drive S drive

Figure 5: EV6R11 Three Phase Configuration

Page 7

With the addition of High Current MOSFET Drivers on the outputs, the IX6R11's typical 6A peak output current capability can be "boosted" to drive the latest IXYS MOSFETS & IGBTs. Figure 6 shows the addition of two IXDD414's. These are CMOS high-speed MOSFET drivers that have a 14A Peak Output Drive Capability, allowing the IX6R11 to drive a pair of IXFK90N20Q 90A/200V Power MOSFETs. The 2 Ohm gate resistors shown should be Non-Inductive High Performance Film resistors such at those available from Caddock. Particular attention also needs to be paid to Suppy By-passing, Grounding, and minimizing the Output Lead Inductance when designing such a high power circuit layout.

PDF page 7 diagram

Figure 6: Boosting the IX6R11 outputs for larger MOSFETs.

DS99102(10/03)