OPA830_1 TI
Document overview
- Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 35
Technical content
FEATURES
/C0068HIGH BANDWIDTH: 250MHz (G = +1) 110MHz (G = +2) /C0068LOW SUPPLY CURRENT: 3.9mA (V S = +5V) /C0068FLEXIBLE SUPPLY RANGE: ±1.4V to ±5.5V Dual Supply +2.8V to +11V Single Supply /C0068INPUT RANGE INCLUDES GROUND ON SINGLE SUPPLY /C00684.88V OUTPUT SWING ON +5V SUPPLY /C0068HIGH SLEW RATE: 550V/ µs /C0068LOW INPUT VOLTAGE NOISE: 9.2nV/ √Hz /C0068Pb-FREE SOT23 PACKAGE
APPLICATIONS
/C0068SINGLE-SUPPLY ANALOG-TO-DIGITAL CONVERTER (ADC) INPUT BUFFERS /C0068SINGLE-SUPPLY VIDEO LINE DRIVERS /C0068CCD IMAGING CHANNELS /C0068LOW-POWER ULTRASOUND /C0068PLL INTEGRATORS /C0068PORTABLE CONSUMER ELECTRONICS OPA830 VIN 750Ω562Ω 2.26kΩ 374Ω 22pF +3V 100Ω +3V THS1040 10−Bit 40MSPS DC-Coupled, +3V ADC Driver
DESCRIPTION
The OPA830 is a low-power, single-supply, wideband, voltage-feedback amplifier designed to operate on a single +3V or +5V supply. Operation on ±5V or +10V supplies is also supported. The input range extends below the negative supply and to within 1.7V of the positive supply. Using complementary common-emitter outputs provides an output swing to within 25mV of either supply while driving 150Ω. High output drive current (±80mA) and low differential gain and phase errors also make them ideal for single-supply consumer video products. Low distortion operation is ensured by the high gain bandwidth product (110MHz) and slew rate (550V/µs), making the OPA830 an ideal input buffer stage to 3V and 5V CMOS ADCs. Unlike other low-power, single-supply amplifiers, distortion performance improves as the signal swing is decreased. A low 9.2nV/√Hz input voltage noise supports wide dynamic range operation. The OPA830 is available in an industry-standard SO-8 package. The OPA830 is also available in an ultra-small SOT23-5 package. For fixed-gain line driver applications, consider the OPA832.
RELATED PRODUCTS
DESCRIPTION SINGLES DUALS TRIPLES QUADS Rail-to-Rail — OPA2830 — OPA4830 Rail-to-Rail Fixed Gain OPA832 OPA2832 OPA3832 — General-Purpose (1800V/µs slew rate) OPA690 OPA2690 OPA3690 — Low-Noise, High DC Precision OPA820 OPA2822 — OPA4820 OPA830 SBOS263F − AUGUST 2004 − REVISED AUGUST 2008 Low-Power, Single-Supply, Wideband Operational Amplifier /C0080/C0082/C0079/C0068/C0085/C0067/C0084/C0073/C0079/C0078 /C0068/C0065/C0084/C0065 /C0105/C0110/C0102/C0111/C0114/C0109/C0097/C0116/C0105/C0111/C0110 /C0105/C0115 /C0099/C0117/C0114/C0114/C0101/C0110/C0116 /C0097/C0115 /C0111/C0102 /C0112/C0117/C0098/C0108/C0105/C0099/C0097/C0116/C0105/C0111/C0110 /C0100/C0097/C0116/C0101/C0046 /C0080/C0114/C0111/C0100/C0117/C0099/C0116/C0115 /C0099/C0111/C0110/C0102/C0111/C0114/C0109 /C0116/C0111 /C0115/C0112/C0101/C0099/C0105/C0102/C0105/C0099/C0097/C0116/C0105/C0111/C0110/C0115 /C0112/C0101/C0114 /C0116/C0104/C0101 /C0116/C0101/C0114/C0109/C0115 /C0111/C0102 /C0084/C0101/C0120/C0097/C0115 /C0073/C0110/C0115/C0116/C0114/C0117/C0109/C0101/C0110/C0116/C0115 /C0115/C0116/C0097/C0110/C0100/C0097/C0114/C0100 /C0119/C0097/C0114/C0114/C0097/C0110/C0116/C0121/C0046 /C0080/C0114/C0111/C0100/C0117/C0099/C0116/C0105/C0111/C0110 /C0112/C0114/C0111/C0099/C0101/C0115/C0115/C0105/C0110/C0103 /C0100/C0111/C0101/C0115 /C0110/C0111/C0116 /C0110/C0101/C0099/C0101/C0115/C0115/C0097/C0114/C0105/C0108/C0121 /C0105/C0110/C0099/C0108/C0117/C0100/C0101 /C0116/C0101/C0115/C0116/C0105/C0110/C0103 /C0111/C0102 /C0097/C0108/C0108 /C0112/C0097/C0114/C0097/C0109/C0101/C0116/C0101/C0114/C0115/C0046 www.ti.com Copyright 2004−2008, Texas Instruments Incorporated Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners.
/C0079/C0080/C0065/C0056/C0051/C0048 SBOS263F − AUGUST 2004 − REVISED AUGUST 2008 www.ti.com ABSOLUTE MAXIMUM RATINGS (1) ESD Rating: (1)Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not supported. This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION (1) PRODUCT PACKAGE-LEAD PACKAGE DESIGNATOR SPECIFIED TEMPERATURE RANGE PACKAGE MARKING ORDERING NUMBER TRANSPORT MEDIA, QUANTITY OPA830 SO-8 Surface-Mount D −40°C to +85°C OPA830 OPA830ID Rails, 100 ″ ″ ″ ″ ″ OPA830IDR Tape and Reel, 2500 OPA830 SOT23-5 DBV −40°C to +85°C A72 OPA830IDBVT Tape and Reel, 250 ″ ″ ″ ″ ″ OPA830IDBVR Tape and Reel, 3000 (1)For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. PIN CONFIGURATIONS Output −VS Noninverting Input +VS Inverting Input A721 Pin Orientation/Package Marking SOT23−5 NC Inverting Input Noninverting Input −VS NC +VS Output NC SO−8 NC = No Connection
/C0079/C0080/C0065/C0056/C0051/C0048 SBOS263F − AUGUST 2004 − REVISED AUGUST 2008 www.ti.com ELECTRICAL CHARACTERISTICS: V S = ±5V Boldface limits are tested at +25°C. At TA = 25°C, G = +2, RF = 750Ω, and RL = 150Ω to GND, unless otherwise noted (see Figure 3). OPA830ID, IDBV TYP MIN/MAX OVER TEMPERATURE TEST PARAMETER CONDITIONS +25°C +25°C (1) 0°C to 70°C (2) −40°C to +85°C (2) UNITS MIN/ MAX TEST LEVEL (3) AC PERFORMANCE (see Figure 3) Small-Signal Bandwidth G = +1, VO ≤ 0.2VPP 310 MHz typ C G = +2, VO ≤ 0.2VPP 120 70 68 65 MHz min B G = +5, VO ≤ 0.2VPP 25 18 16 15 MHz min B G = +10, VO ≤ 0.2VPP 11 8 7 6 MHz min B Gain-Bandwidth Product G ≥ +10 110 85 82 80 MHz min B Peaking at a Gain of +1 VO ≤ 0.2VPP 6 dB typ C Slew Rate G = +2, 2V Step 600 280 270 260 V/µs min B Settling Time to 0.1% G = +2, 1V Step 42 63 65 66 ns max B Harmonic Distortion VO = 2VPP, f = 5MHz 2nd-Harmonic R L = 150Ω −67 −59 −57 −56 dBc max B R L ≥ 500Ω −71 −62 −61 −60 dBc max B 3rd-Harmonic R L = 150Ω −60 −50 −49 −48 dBc max B R L ≥ 500Ω −77 −65 −62 −59 dBc max B Input Voltage Noise f > 1MHz 9.5 10.5 11.0 11.5 nV/√Hz max B Input Current Noise f > 1MHz 3.7 4.7 5.2 5.7 pA/√Hz max B NTSC Differential Gain 0.07 % typ C NTSC Differential Phase 0.17 ° typ C DC PERFORMANCE (4) R L = 150Ω Open-Loop Voltage Gain 74 66 65 64 dB min A Input Offset Voltage ±1.5 ±7 ±8.1 ±8.6 mV max A Average Offset Voltage Drift — ±25 ±25 µV/°C max B Input Bias Current VCM = 0V +5 +10 +12 +13 µA max A Input Bias Current Drift ±12 ±12 nA/°C max B Input Offset Current VCM = 0V ±0.1 ±1 ±1.2 ±1.4 µA max A Input Offset Current Drift — ±5 ±5 nA/°C max B INPUT Negative Input Voltage(5) −5.5 −5.4 −5.3 −5.2 V max A Positive Input Voltage(5) 3.2 3.1 3.0 2.9 V min A Common-Mode Rejection Ratio (CMRR) Input-Referred 80 76 74 72 dB min A Input Impedance Differential Mode 10 2.1 kΩ pF typ C Common-Mode 400 1.2 kΩ pF typ C OUTPUT Output Voltage Swing G = +2, RL = 1kΩ to GND ±4.88 ±4.86 ±4.85 ±4.84 V min A G = +2, RL = 150Ω to GND ±4.64 ±4.60 ±4.58 ±4.56 V min A Current Output, Sinking and Sourcing ±85 ±65 ±60 ±55 mA min A Short-Circuit Current Output Shorted to Ground 150 mA typ C Closed-Loop Output Impedance G = +2, f ≤ 100kHz 0.06 Ω typ C POWER SUPPLY Minimum Operating Voltage ±1.4 V typ C Maximum Operating Voltage ±5.5 ±5.5 ±5.5 V max A Maximum Quiescent Current VS = ±5V 4.25 4.7 5.3 5.9 mA max A Minimum Quiescent Current VS = ±5V 4.25 4.0 3.6 3.3 mA min A Power-Supply Rejection Ratio (+PSRR) Input-Referred 66 61 60 59 dB min A THERMAL CHARACTERISTICS Specification: ID, IDBV −40 to +85 °C typ C Thermal Resistance, /C0113JA D SO-8 125 °C/W typ C DBV SOT23-5 150 °C/W typ C (1)Junction temperature = ambient for +25°C specifications. (2)Junction temperature = ambient at low temperature limits; junction temperature = ambient +5°C at high temperature limit for over temperature specifications. (3)Test levels: (A) 100% tested at +25°C. Over temperature limits by characterization and simulation. (B) Limits set by characterization and simulation. (C) Typical value only for information. (4)Current is considered positive out of pin. (5)Tested < 3dB below minimum specified CMRR at ± CMIR limits.
/C0079/C0080/C0065/C0056/C0051/C0048 SBOS263F − AUGUST 2004 − REVISED AUGUST 2008 www.ti.com ELECTRICAL CHARACTERISTICS: V S = +5V Boldface limits are tested at +25°C. At TA = 25°C, G = +2, RF = 750Ω, and RL = 150Ω to VS/2, unless otherwise noted (see Figure 1). OPA830ID, IDBV TYP MIN/MAX OVER TEMPERATURE TEST PARAMETER CONDITIONS +25°C +25°C (1) 0°C to 70°C (2) −40°C to +85°C (2) UNITS MIN/ MAX TEST LEVEL (3) AC PERFORMANCE (see Figure 1) Small-Signal Bandwidth G = +1, VO ≤ 0.2VPP 250 MHz typ C G = +2, VO ≤ 0.2VPP 110 72 70 68 MHz min B G = +5, VO ≤ 0.2VPP 24 17 16 15 MHz min B G = +10, VO ≤ 0.2VPP 11 8 7 6 MHz min B Gain-Bandwidth Product G ≥ +10 110 84 80 79 MHz min B Peaking at a Gain of +1 VO ≤ 0.2VPP 5 dB typ C Slew Rate G = +2, 2V Step 550 280 270 260 V/µs min B Settling Time to 0.1% G = +2, 1V Step 43 64 66 67 ns max B Harmonic Distortion VO = 2VPP, f = 5MHz 2nd-Harmonic R L = 150Ω −62 −55 −54 −53 dBc max B R L ≥ 500Ω −64 −58 −57 −56 dBc max B 3rd-Harmonic R L = 150Ω −58 −50 −49 −48 dBc max B R L ≥ 500Ω −84 −66 −63 −60 dBc max B Input Voltage Noise f > 1MHz 9.2 10.2 10.7 11.2 nV/√Hz max B Input Current Noise f > 1MHz 3.5 4.5 5.0 5.5 pA/√Hz max B NTSC Differential Gain 0.08 % typ C NTSC Differential Phase 0.09 ° typ C DC PERFORMANCE (4) R L = 150Ω Open-Loop Voltage Gain 72 66 65 64 dB min A Input Offset Voltage ±0.5 ±5.0 ±6.0 ±6.5 mV max A Average Offset Voltage Drift — ±20 ±20 µV/°C max B Input Bias Current VCM = 2.5V +5 +10 +12 +13 µA max A Input Bias Current Drift ±12 ±12 nA/°C max B Input Offset Current VCM = 2.5V ±0.1 ±0.8 ±1 ±1.2 µA max A Input Offset Current Drift — ±5 ±5 nA/°C max B INPUT Least Positive Input Voltage(5) −0.5 −0.4 −0.3 −0.2 V max A Most Positive Input Voltage(5) 3.2 3.1 3.0 2.9 V min A Common-Mode Rejection Ratio (CMRR) Input-Referred 80 76 74 72 dB min A Input Impedance Differential-Mode 10 2.1 kΩ pF typ C Common-Mode 4001.2 kΩ pF typ C OUTPUT Current Output, Sourcing and Sinking ±80 ±60 ±55 ±52 mA min A Short-Circuit Output Current Output Shorted to Either Supply 140 mA typ C Closed-Loop Output Impedance G = +2, f ≤ 100kHz 0.06 Ω typ C POWER SUPPLY Minimum Operating Voltage +2.8 V typ C Maximum Operating Voltage +11 +11 +11 V max A Maximum Quiescent Current VS = +5V 3.9 4.1 4.8 5.5 mA max A Minimum Quiescent Current VS = +5V 3.9 3.7 3.4 3.1 mA min A Power-Supply Rejection Ratio (PSRR) Input-Referred 66 61 60 59 dB min A THERMAL CHARACTERISTICS Specification: ID, IDBV −40 to +85 °C typ C Thermal Resistance, /C0113JA D SO-8 125 °C/W typ C DBV SOT23-5 150 °C/W typ C (1) Junction temperature = ambient for +25°C specifications. (2) Junction temperature = ambient at low temperature limits; junction temperature = ambient +5°C at high temperature limit for over temperature. (3) Test levels: (A) 100% tested at +25°C. Over temperature limits by characterization and simulation. (B) Limits set by characterization and simulation. (C) Typical value only for information. (4) Current considered positive out of pin. (5) Tested < 3dB below minimum specified CMRR at ± CMIR limits.
/C0079/C0080/C0065/C0056/C0051/C0048 SBOS263F − AUGUST 2004 − REVISED AUGUST 2008 www.ti.com ELECTRICAL CHARACTERISTICS: V S = +3V Boldface limits are tested at +25°C. At TA = 25°C, G = +2, and RL = 150Ω to VS/3, unless otherwise noted (see Figure 2). OPA830ID, IDBV TYP MIN/MAX OVER TEMPERATURE TEST PARAMETER CONDITIONS +25°C +25°C (1) 0°C to 70°C (2) UNITS MIN/ MAX TEST LEVEL (3) AC PERFORMANCE (see Figure 2) Small-Signal Bandwidth G = +2, VO ≤ 0.2VPP 100 72 68 MHz min B G = +5, VO ≤ 0.2VPP 22 17 16 MHz min B G = +10, VO ≤ 0.2VPP 10 8 7 MHz min B Gain-Bandwidth Product G ≥ +10 100 80 76 MHz min B Slew Rate 1V Step 225 140 110 V/µs min B Rise Time 0.5V Step 3.3 5.5 5.6 ns max B Fall Time 0.5V Step 3.3 5.5 5.6 ns max B Settling Time to 0.1% 1V Step 45 72 87 ns max B Harmonic Distortion VO = 1VPP, f = 5MHz 2nd-Harmonic R L = 150Ω −67 −61 −59 dBc max B R L ≥ 500Ω −67 −61 −59 dBc max B 3rd-Harmonic R L = 150Ω −66 −59 −58 dBc max B R L ≥ 500Ω −77 −59 −58 dBc max B Input Voltage Noise f > 1MHz 9.2 10.2 10.7 nV/√Hz max B Input Current Noise f > 1MHz 3.5 4.5 5.0 pA/√Hz max B DC PERFORMANCE (4) Open-Loop Voltage Gain 72 66 65 dB min A Input Offset Voltage ±1.5 ±7 ±8.1 mV max A Average Offset Voltage Drift — ±25 µV/°C max B Input Bias Current VCM = 1.0V +5 +10 +12 µA max A Input Bias Current Drift ±12 nA/°C max B Input Offset Current VCM = 1.0V ±0.1 ±1 ±1.2 µA max A Input Offset Current Drift — ±5 nA/°C max B INPUT Least Positive Input Voltage(5) −0.45 −0.4 −0.27 V max A Most Positive Input Voltage(5) 1.2 1.1 1.0 V min A Common-Mode Rejection Ratio (CMRR) Input-Referred 80 75 73 dB min A Input Impedance Differential-Mode 10 2.1 kΩ pF typ C Common-Mode 4001.2 kΩ pF typ C OUTPUT Least Positive Output Voltage G = +5, RL = 1kΩ to 1.5V 0.08 0.11 0.125 V max A G = +5, RL = 150Ω to 1.5V 0.17 0.39 0.40 V max A Most Positive Output Voltage G = +5, RL = 1kΩ to 1.5V 2.91 2.88 2.85 V min A G = +5, RL = 150Ω to 1.5V 2.82 2.74 2.70 V min A Current Output, Sourcing 30 20 18 mA min A Current Output, Sinking 30 20 18 mA min A Short-Circuit Output Current Output Shorted to Either Supply 45 mA typ C Closed-Loop Output Impedance See Figure 2, f < 100kHz 0.06 Ω typ C POWER SUPPLY Minimum Operating Voltage +2.8 V min B Maximum Operating Voltage +11 +11 V max A Maximum Quiescent Current VS = +3V 3.7 4.0 4.7 mA max A Minimum Quiescent Current VS = +3V 3.7 3.3 3.1 mA min A Power-Supply Rejection Ratio (PSRR) Input-Referred 64 60 58 dB min A THERMAL CHARACTERISTICS Specification: ID, IDBV −40 to +85 °C typ C Thermal Resistance, /C0113JA D SO-8 125 °C/W typ C DBV SOT23-5 150 °C/W typ C (1)Junction temperature = ambient for +25°C specifications. (2)Junction temperature = ambient at low temperature limits; junction temperature = ambient +5°C at high temperature limit for over temperature. (3)Test levels: (A) 100% tested at +25°C. Over temperature limits by characterization and simulation. (B) Limits set by characterization and simulation. (C) Typical value only for information. (4)Current considered positive out of pin. (5)Tested < 3dB below minimum specified CMRR at ± CMIR limits.
/C0079/C0080/C0065/C0056/C0051/C0048 SBOS263F − AUGUST 2004 − REVISED AUGUST 2008 www.ti.com TYPICAL CHARACTERISTICS: V S = ±5V At TA = 25°C, G = +2, RF = 750Ω, and RL = 150Ω to GND, unless otherwise noted (see Figure 3). −12 −15 −18 NONINVERTING SMALL−SIGNAL FREQUENCY RESPONSE Frequency (MHz) Normalized Gain (dB) 1 10 100 600 VO =0 . 2 VPP R L =1 5 0Ω See Figure 3 G=+ 1 R F =0 Ω G=+ 2 G=+ 5 G=+ 1 0 −12 NONINVERTING LARGE−SIGNAL FREQUENCY RESPONSE Frequency (MHz) Gain (dB) 10 100 500 VO =4 VPP VO =2 VPP VO =1 VPP VO =0 . 5 VPP G=+ 2 V / V R L = 150Ω S e eF i g u r e3 0.4 0.3 0.2 0.1 −0.1 −0.2 −0.3 −0.4 NONINVERTING PULSE RESPONSE Time (10ns/div) Small−Signal Output Voltage (100mV/div) 2.0 1.5 1.0 0.5 −0.5 −1.0 −1.5 −2.0 Large−Signal Output Voltage (500mV/div) Large−Signal± 1V Right Scale Small−Signal± 100mV Left Scale G=+ 2 V / V S e eF i g u r e3 −12 −15 −18 INVERTING SMALL−SIGNAL FREQUENCY RESPONSE Frequency (MHz) Normalized Gain (dB) 11 0 1 0 0 4 0 0 VO =0 . 2 VPP R L =1 5 0Ω G= −2 G= −10 G= −1 G= −5 −12 −15 −18 INVERTING LARGE−SIGNAL FREQUENCY RESPONSE Frequency (MHz) Gain (dB) 10 100 400 G= −1V/V R L =1 5 0Ω VO =2 VPP VO =4 VPP VO =1 VPP VO =0 . 5 VPP 0.4 0.3 0.2 0.1 −0.1 −0.2 −0.3 −0.4 INVERTING PULSE RESPONSE Time (10ns/div) Small−Signal Output Voltage (100mV/div) 2.0 1.5 1.0 0.5 −0.5 −1.0 −1.5 −2.0 Large−Signal Output Voltage (500mV/div) Large−Signal± 1V Right Scale Small−Signal± 100mV Left Scale G= −1V/V
/C0079/C0080/C0065/C0056/C0051/C0048 SBOS263F − AUGUST 2004 − REVISED AUGUST 2008 www.ti.com TYPICAL CHARACTERISTICS: V S = ±5V (continued) At TA = 25°C, G = +2, RF = 750Ω, and RL = 150Ω to GND, unless otherwise noted (see Figure 3). −50 −55 −60 −65 −70 −75 −80 −85 HARMONIC DISTORTION vs LOAD RESISTANCE Resistance (Ω) Harmonic Distortion (dBc) 100 1000 f=5 M H z VO =2 VPP G=+ 2 V / V See Figure 3 3rd−Harmonic 2nd−Harmonic −55 −60 −65 −70 −75 −80 −85 −90 −95 HARMONIC DISTORTION vs OUTPUT VOLTAGE Output Voltage Swing (VPP ) Harmonic Distortion (dBc) 0.1 1 10 2nd−Harmonic 3rd−Harmonic f=5 M H z R L =5 0 0Ω G=+ 2 V / V See Figure 3 −40 −45 −50 −55 −60 −65 −70 −75 −80 −85 −90 TWO−TONE, 3RD−ORDER INTERMODULATION SPURIOUS Single−Tone Load Power (2dBm/div) 3rd−Order Spurious Level (dBc) 10MHz 5MHz 20MHz 750Ω OPA830 P I PO50Ω 500Ω 750Ω −40 −45 −50 −55 −60 −65 −70 −75 −80 −85 −90 5MHz HARMONIC DISTORTION vs SUPPLY VOLTAGE Supply Voltage (±VS) Harmonic Distortion (dBc) VO =2 VPP R L =5 0 0Ω G=+ 2 V / V S e eF i g u r e3 2nd−Harmonic 3rd−Harmonic Input Limited for VCM =0 V −50 −55 −60 −65 −70 −75 −80 −85 −90 −95 −100 −105 HARMONIC DISTORTION vs FREQUENCY Frequency (MHz) Harmonic Distortion (dBc) 0.1 1 10 3rd−Harmonic R L =1 5 0Ω 2nd−Harmonic R L = 150Ω 2nd−Harmonic R L =5 0 0Ω 3rd−Harmonic R L = 500Ω VO =2 VPP G=+ 2 V / V S e eF i g u r e3 SUPPLY AND OUTPUT CURRENT vs TEMPERATURE Ambient Temperature (/C0095C) Output Current (50mA/div) 6.0 5.5 5.0 4.5 4.0 3.5 3.0 Supply Current (4mA/div) −50 −2 50 2 55 07 5 1 0 0 1 2 5 Source/Sink Output Current Left Scale Supply Current Right Scale
/C0079/C0080/C0065/C0056/C0051/C0048 SBOS263F − AUGUST 2004 − REVISED AUGUST 2008 www.ti.com TYPICAL CHARACTERISTICS: V S = ±5V (continued) At TA = 25°C, G = +2, RF = 750Ω, and RL = 150Ω to GND, unless otherwise noted (see Figure 3). FREQUENCY RESPONSE vs CAPACITIVE LOAD Frequency (MHz) Normalized Gain to Capacitive Load (dB) 11 0 1 0 0 2 0 0 C L = 1000pF C L = 100pF C L =1 0 p F 750Ω R S OPA830 V I V O50Ω 1kΩ(1)C L 750 Ω NOTE: (1) 1kΩ is op tional. OUTPUT SWING vs LOAD RESISTANCE Resistance (Ω) Output Voltage (V) 10 100 1k G=+ 5 V / V VS = ±5V 120 110 100 RECOMMENDED R S vs CAPACITIVE LOAD Capacitive Load (pF) R S (Ω) 1 10 100 1k 0dB Peaking Targeted OUTPUT VOLTAGE AND CURRENT LIMITATIONS I O (mA) VO (V) −160 −120 −80 −40 0 40 80 120 160 1W Internal Power Limit Output Current Limit Output Current Limit 1W Internal Power Limit R L = 500Ω R L =1 0 0Ω R L =5 0Ω
/C0079/C0080/C0065/C0056/C0051/C0048 SBOS263F − AUGUST 2004 − REVISED AUGUST 2008 www.ti.com TYPICAL CHARACTERISTICS: V S = ±5V, Differential Configuration At TA = 25°C, GD = +2, RF = 604Ω, and RL = 500Ω, unless otherwise noted. R L 500 Ω 604 Ω 604 ΩR G R G V O V I G D = 604Ω R G +5V −5V −5V +5V OPA830 OPA830 DIFFERENTIAL LARGE−SIGNAL FREQUENCY RESPONSE Frequency (MHz) 1 10 200 100 Gain (dB) VO =5 VPP VO =2 VPP VO =1 VPP VO = 200mVPP G D =2 R L = 500Ω −40 −50 −60 −70 −80 −90 −100 −110 DIFFERENTIAL DISTORTION vs FREQUENCY Frequency (MHz) 0.1 1 10 100 Harmonic Distortion (dBc) 3rd−Harmonic 2nd−Harmonic G D =2 VO =4 VPP R L =5 0 0Ω −12 −15 DIFFERENTIAL SMALL−SIGNAL FREQUENCY RESPONSE Frequency (MHz) 1 10 100 200 Normalized Gain (dB) G D =1 G D =2 G D =5 G D =1 0 VO =2 0 0 m VPP R L =5 0 0Ω −45 −50 −55 −60 −65 −70 −75 −80 −85 −90 −95 −100 DIFFERENTIAL DISTORTION vs LOAD RESISTANCE Resistance (Ω) 100 150 200 250 300 350 400 450 500 Harmonic Distortion (dBc) 3rd−Harmonic 2nd−Harmonic VO =4 VPP G D =2 f=5 M H z −55 −60 −65 −70 −75 −80 −85 −90 −95 −100 −105 DIFFERENTIAL DISTORTION vs OUTPUT VOLTAGE Output Voltage Swing (VPP ) 11 0 Harmonic Distrtion (dBc) 3rd−Harmonic 2nd−Harmonic G D =2 R L = 500Ω f=5 M H z
/C0079/C0080/C0065/C0056/C0051/C0048 SBOS263F − AUGUST 2004 − REVISED AUGUST 2008 www.ti.com TYPICAL CHARACTERISTICS: V S = +5V At TA = 25°C, G = +2, RF = 750Ω, RL = 150Ω to VS/2, and input VCM = 2.5V, unless otherwise noted (see Figure 1). −12 −15 −18 NONINVERTING SMALL−SIGNAL FREQUENCY RESPONSE Frequency (MHz) Normalized Gain (dB) 11 0 1 0 0 5 0 0 VO =0 . 2 VPP R L =1 5 0Ω See Figure 1 G=+ 1 R F =0 Ω G=+ 2 G=+ 5 G=+ 1 0 −12 NONINVERTING LARGE−SIGNAL FREQUENCY RESPONSE Frequency (MHz) Gain (dB) 10 100 500 G=+ 2 V / V R L =1 5 0Ω See Figure 1 VO =2 VPP VO =1 VPP VO =0 . 5 VPP 2.9 2.8 2.7 2.6 2.5 2.4 2.3 2.2 2.1 NONINVERTING PULSE RESPONSE Time (10ns/div) Small−Signal Output Voltage (100mV/div) 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 Large−Signal Output Voltage (500mV/div) Large−Signal± 1V Right Scale Small−Signal± 100mV Left Scale G=+ 2 V / V See Figure 1 −12 −15 −18 INVERTING SMALL−SIGNAL FREQUENCY RESPONSE Frequency (MHz) Normalized Gain (dB) 11 0 1 0 0 4 0 0 VO =0 . 2 VPP R L = 150Ω S e eF i g u r e9 G= −2 G= −10 G= −1 G= −5 −12 −15 −18 INVERTING LARGE−SIGNAL FREQUENCY RESPONSE Frequency (MHz) Gain (dB) 10 100 500 G= −1V/V R L =1 5 0Ω See Figure 9 VO =2 VPP VO =1 VPP VO =0 . 5 VPP 2.9 2.8 2.7 2.6 2.5 2.4 2.3 2.2 2.1 INVERTING PULSE RESPONSE Time (10ns/div) Small−Signal Output Voltage (100mV/div) 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 Large−Signal Output Voltage (500mV/div) Large−Signal± 1V Right Scale Small−Signal± 100mV Left Scale G= −1V/V
/C0079/C0080/C0065/C0056/C0051/C0048 SBOS263F − AUGUST 2004 − REVISED AUGUST 2008 www.ti.com TYPICAL CHARACTERISTICS: V S = +5V (continued) At TA = 25°C, G = +2, RF = 750Ω, RL = 150Ω to VS/2, and input VCM = 2.5V, unless otherwise noted (see Figure 1). −50 −55 −60 −65 −70 −75 −80 −85 −90 HARMONIC DISTORTION vs LOAD RESISTANCE Load Resistance (Ω ) Harmonic Distortion (dBc) 100 1000 f=5 M H z VO =2 VPP G=+ 2 V / V S e eF i g u r e1 3rd−Harmonic 2nd−Harmonic −45 −50 −55 −60 −65 −70 −75 −80 −85 −90 −95 −100 HARMONIC DISTORTION vs OUTPUT VOLTAGE Output Voltage Swing (VPP ) Harmonic Distortion (dBc) 0.1 1 10 2nd−Harmonic 3rd−Harmonic f=5 M H z R L =5 0 0Ω G=+ 2 V / V See Figure 1 Input Limited −55 −60 −65 −70 −75 −80 −85 HARMONIC DISTORTION vs INVERTING GAIN Gain ( V/V ) Harmonic Distortion (dBc) 11 0 f=5 M H z R L =5 0 0Ω VO =2 VPP 3rd−Harmonic 2nd−Harmonic −50 −55 −60 −65 −70 −75 −80 −85 −90 −95 −100 −105 HARMONIC DISTORTION vs FREQUENCY Frequency (MHz) Harmonic Distortion (dBc) 0.1 1 10 3rd−Harmonic R L =1 5 0Ω 2nd−Harmonic R L =1 5 0Ω 2nd−Harmonic R L = 500Ω 3rd−Harmonic R L = 500Ω G=+ 2 V / V VO =2 VPP S e eF i g u r e1 −55 −60 −65 −70 −75 −80 −85 −90 HARMONIC DISTORTION vs NONINVERTING GAIN Gain (V/V) Harmonic Distortion (dBc) 11 0 f=5 M H z R L =5 0 0Ω VO =2 VPP See Figure 1 3rd−Harmonic 2nd−Harmonic −45 −50 −55 −60 −65 −70 −75 −80 −85 −90 −95 TWO−TONE, 3RD−ORDER INTERMODULATION SPURIOUS Single−Tone Load Power (dBm) 3rd−Order Spurious Level (dBc) 10MHz 5MHz 20MHz 750Ω OPA830 P I PO50Ω 500Ω 750Ω
/C0079/C0080/C0065/C0056/C0051/C0048 SBOS263F − AUGUST 2004 − REVISED AUGUST 2008 www.ti.com TYPICAL CHARACTERISTICS: V S = +5V (continued) At TA = 25°C, G = +2, RF = 750Ω, RL = 150Ω to VS/2, and input VCM = 2.5V, unless otherwise noted (see Figure 1). 100 INPUT VOLTAGE AND CURRENT NOISE DENSITY Frequency (Hz) 10 100 1k 10k 100k 1M 10M Voltage Noise (nV/√Hz) Current Noise (pA/√Hz) Voltage Noise (9.2nV/√Hz) Current Noise (3.5pA/√Hz) 130 120 110 100 RECOMMENDED R S vs CAPACITIVE LOAD Capacitive Load (pF) R S (Ω) 1 10 100 1k 0dB Peaking Targeted −10 −20 OPEN−LOOP GAIN AND PHASE Frequency (Hz) Open−Loop Gain (dB) −20 −40 −60 −80 −100 −120 −140 −160 −180 −200 Open−Loop Phase (/C0095) 100 1k 10k 100k 1M 10M 100M 1G 20 log (AOL ) ∠(AOL ) 100 0.1 0.01 CLOSED−LOOP OUTPUT IMPEDANCE vs FREQUENCY Frequency (Hz) Output Impedance (Ω) 1k 10k 100k 1M 10M 100M FREQUENCY RESPONSE vs CAPACITIVE LOAD Frequency (MHz) Normalized Gain to Capacitive Load (dB) 1 10 100 300 C L = 1000pF C L = 100pF C L = 10pF 750Ω R S OPA830 VI VO50Ω 1kΩ(1)C L 750Ω NOTE: (1) 1kΩis optional. 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 −0.5 −1.0 VOLTAGE RANGES vs TEMPERATURE Ambient Temperature (10/C0095C/div) −50 0 50 110 Voltage Range (V) Most Positive Output Voltage Most Positive Input Voltage Least Positive Output Voltage Least Positive Input Voltage R L =1 5 0Ω
/C0079/C0080/C0065/C0056/C0051/C0048 SBOS263F − AUGUST 2004 − REVISED AUGUST 2008 www.ti.com TYPICAL CHARACTERISTICS: V S = +5V (continued) At TA = 25°C, G = +2, RF = 750Ω, RL = 150Ω to VS/2, and input VCM = 2.5V, unless otherwise noted (see Figure 1). TYPICAL DC DRIFT OVER TEMPERATURE Ambient Temperature (/C0095C) Input Offset Voltage (mV) Input Bias and Offset Current (µV) −50 −2 50 2 55 07 5 1 0 0 1 2 5 Input Bias Current (IB) 10 × Input Offset Current (IOS ) Input Offset Voltage (VOS ) CMRR AND PSRR vs FREQUENCY Frequency (Hz) Common−Mode Rejection Ratio (dB) Power−Supply Rejection Ratio (dB) 1k 10k 100k 1M 10M 100M CMRR PSRR 100 SUPPLY AND OUTPUT CURRENT vs TEMPERATURE Ambient Temperature (/C0095C) Output Current (5mA/div) 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 Supply Current (0.5mA/div) −50 −2 50 2 55 07 5 1 0 0 1 2 5 Output Current, Sinking Quiescent Current Output Current, Sourcing 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 −0.5 OUTPUT SWING vs LOAD RESISTANCE Load Resistance (Ω) Output Voltage (V) 10 100 1k G=+ 5 V / V
/C0079/C0080/C0065/C0056/C0051/C0048 SBOS263F − AUGUST 2004 − REVISED AUGUST 2008 www.ti.com TYPICAL CHARACTERISTICS: V S = +5V, Differential Configuration At TA = 25°C, G = +2, RF = 604Ω, and RL = 500Ω differential, unless otherwise noted. R L 604 Ω 604 ΩR G R G V O V I G D = 604Ω R G +5V +5V OPA830 OPA830 1.2kΩ 1.2kΩ 1.2kΩ 0.1µF 1.2kΩ 0.1µF 2.5V 2.5V DIFFERENTIAL LARGE−SIGNAL FREQUENCY RESPONSE Frequency (MHz) 1 10 100 200 Gain (dB) VO =3 VPP VO =2 VPP VO =1 VPP VO =0 . 2 VPPG D =2 R L =5 0 0Ω −30 −40 −50 −60 −70 −80 −90 −100 −110 DIFFERENTIAL DISTORTION vs FREQUENCY Frequency (MHz) 1 10 100 Harmonic Distrtion (dBc) 3rd−Harmonic 2nd−Harmonic VO =4 VPP G D =2 R L =5 0 0Ω −12 −15 DIFFERENTIAL SMALL−SIGNAL FREQUENCY RESPONSE Frequency (MHz) 1 10 100 200 Normalized Gain (dB) G D =1 G D =2 G D =5 G D =1 0 VO = 200mV PP R L = 500Ω −40 −45 −50 −55 −60 −65 −70 −75 −80 −85 −90 DIFFERENTIAL DISTORTION vs LOAD RESISTANCE Resistance (Ω) 100 150 200 250 300 350 400 450 500 Harmonic Distortion (dBc) 3rd−Harmonic 2nd−Harmonic VO =4 VPP G D =2 f=5 M H z −55 −60 −65 −70 −75 −80 −85 −90 −95 −100 DIFFERENTIAL DISTORTION vs OUTPUT VOLTAGE Output Voltage Swing (VPP ) 11 0 Harmonic Distrtion (dBc) 3rd−Harmonic 2nd−Harmonic G D =2 R L = 500Ω f=5 M H z
/C0079/C0080/C0065/C0056/C0051/C0048 SBOS263F − AUGUST 2004 − REVISED AUGUST 2008 www.ti.com TYPICAL CHARACTERISTICS: V S = +3V At TA = 25°C, G = +2, and RL = 150Ω to VS/3, unless otherwise noted (see Figure 2). −12 −15 −18 NONINVERTING SMALL−SIGNAL FREQUENCY RESPONSE Frequency (MHz) Normalized Gain (dB) 11 0 1 0 0 4 0 0 R L = 150Ω VO =0 . 2 VPP S e eF i g u r e2 G=+ 2 G=+ 1 0 G=+ 5 −12 NONINVERTING LARGE−SIGNAL FREQUENCY RESPONSE Frequency (MHz) Gain (dB) 10 100 400 R L =1 5 0Ω G=+ 2 V / V See Figure 2 VO =1 . 5 VPP VO =1 VPPVO =0 . 5 VPP 1.20 1.15 1.10 1.05 1.00 0.95 0.90 0.85 0.80 NONINVERTING PULSE RESPONSE Time (10ns/div) Small−Signal Output Voltage (90mV/div) 2.00 1.75 1.50 1.25 1.00 0.75 0.50 0.25 Large−Signal Output Voltage (250mV/div) Large−Signal± 0.5V Right Scale Small−Signal± 100mV Left Scale G=+ 2 V / V See Figure 2 −12 −15 −18 INVERTING SMALL−SIGNAL FREQUENCY RESPONSE Frequency (MHz) Normalized Gain (dB) 1 10 100 300 G= −10 G= −5 G= −2 G= −1 R L = 150Ω VO =0 . 2 VPP −12 −15 −18 INVERTING LARGE−SIGNAL FREQUENCY RESPONSE Frequency (MHz) Gain (dB) 10 100 300 R L =1 5 0Ω G= −1V/V VO =1 . 5 VPP VO =1 VPP VO =0 . 5 VPP 1.20 1.15 1.10 1.05 1.00 0.95 0.90 0.85 0.80 INVERTING PULSE RESPONSE Time (10ns/div) Small−Signal Output Voltage (90mV/div) 2.00 1.75 1.50 1.25 1.00 0.75 0.50 0.25 Large−Signal Output Voltage (250mV/div) Large−Signal± 0.5V Right Scale Small−Signal± 100mV Left Scale G= −1V/V
/C0079/C0080/C0065/C0056/C0051/C0048 SBOS263F − AUGUST 2004 − REVISED AUGUST 2008 www.ti.com TYPICAL CHARACTERISTICS: V S = +3V (continued) At TA = 25°C, G = +2, and RL = 150Ω to VS/3, unless otherwise noted (see Figure 2). −50 −55 −60 −65 −70 −75 −80 −85 −90 HARMONIC DISTORTION vs LOAD RESISTANCE Resistance (Ω) Harmonic Distortion (dBc) 100 1000 f=5 M H z VO =1 VPP G=+ 2 V / V S e eF i g u r e2 3rd−Harmonic 2nd−Harmonic −55 −60 −65 −70 −75 −80 −85 −90 −95 −100 HARMONIC DISTORTION vs FREQUENCY Frequency (MHz) Harmonic Distortion (dBc) 0.1 1 10 2nd−Harmonic R L = 150Ω 2nd−Harmonic R L = 500Ω 3rd−Harmonic R L = 150Ω 3rd−Harmonic R L = 500Ω VO =1 VPP G=+ 2 V / V S e eF i g u r e2 190 170 150 130 110 RECOMMENDED R S vs CAPACITIVE LOAD Capacitive Load (pF) R S (Ω) 1 10 100 1k 0dB Peaking Targeted −40 −50 −60 −70 −80 −90 −100 HARMONIC DISTORTION vs OUTPUT VOLTAGE Output Voltage Swing (VPP ) Harmonic Distortion (dBc) 0.1 1 10 2nd−Harmonic 3rd−Harmonic f=5 M H z R L =5 0 0Ω G=+ 2 V / V S e eF i g u r e2 Input Limited −40 −45 −50 −55 −60 −65 −70 −75 −80 −85 −90 −95 TWO−TONE, 3RD−ORDER INTERMODULATION SPURIOUS Single−Tone Load Power (dBm) 3rd−Order Spurious Level (dBc) 10MHz 5MHz 20MHz 750Ω OPA830 P I PO50Ω 500Ω 750Ω FREQUENCY RESPONSE vs CAPACITIVE LOAD Frequency (MHz) Normalized Gain to Capacitive Load (dB) 1 10 100 20 0 C L = 1000pF C L = 100pF C L = 10pF 750Ω R SV I V O50Ω 1kΩ(1)C L 750Ω NOTE: (1) 1kΩ is optional. OPA830
/C0079/C0080/C0065/C0056/C0051/C0048 SBOS263F − AUGUST 2004 − REVISED AUGUST 2008 www.ti.com TYPICAL CHARACTERISTICS: V S = +3V (continued) At TA = 25°C, G = +2, and RL = 150Ω to VS/3, unless otherwise noted (see Figure 2). 3.5 3.0 2.5 2.0 1.5 1.0 0.5 −0.5 OUTPUT SWING vs LOAD RESISTANCE Load Resistance (Ω ) Output Voltage (V) 10 100 1k G=+ 5 V / V
/C0079/C0080/C0065/C0056/C0051/C0048 SBOS263F − AUGUST 2004 − REVISED AUGUST 2008 www.ti.com TYPICAL CHARACTERISTICS: V S = +3V, Differential Configuration At TA = 25°C, G = +2, RF = 604Ω, and RL = 500Ω differential, unless otherwise noted. R L 604 Ω 604 ΩR G R G V O V I G D = 604 Ω R G +3V 2kΩ 1kΩ 0.1µF 2kΩ 1kΩ +3V OPA830 OPA830 0.1µF DIFFERENTIAL LARGE−SIGNAL FREQUENCY RESPONSE Frequency (MHz) 1 10 100 200 Gain (dB) VO =2 VPP VO =1 VPP VO =2 0 0 m VPP G D =2 −35 −45 −55 −65 −75 −85 −95 −105 −115 DIFFERENTIAL DISTORTION vs FREQUENCY Frequency (MHz) 0.1 1 10 100 Harmonic Distortion (dBc) 3rd−Harmonic 2nd−Harmonic G D =2 VO =2 VPP R L = 500Ω −12 −15 DIFFERENTIAL SMALL−SIGNAL FREQUENCY RESPONSE Frequency (MHz) 1 10 100 200 Normalized Gain (dB) G D =1 G D =2 G D =5 G D =1 0 VO = 200mV PP R L = 500Ω −40 −45 −50 −55 −60 −65 −70 −75 −80 −85 −90 DIFFERENTIAL DISTORTION vs LOAD RESISTANCE Resistance (Ω) 100 150 200 250 300 350 400 450 500 Harmonic Distortion (dBc) 3rd−Harmonic 2nd−Harmonic VO =4 VPP G D =2 f=5 M H z −75 −80 −85 −90 −95 −100 DIFFERENTIAL DISTORTION vs OUTPUT VOLTAGE Output Voltage Swing (VPP ) Harmonic Distortion (dBc) 3rd−Harmonic 2nd−Harmonic G D =2 R L =5 0 0Ω f=5 M H z
filter using the Sallen-Key topology. fixtures is shown in Table 1. Table 1. Demonstration Fixtures by Package Figure 8. Single-Supply, High-Frequency Active Filter
/C0079/C0080/C0065/C0056/C0051/C0048 SBOS263F − AUGUST 2004 − REVISED AUGUST 2008 www.ti.com MACROMODEL AND APPLICATIONS SUPPORT Computer simulation of circuit performance using SPICE is often a quick way to analyze the performance of the OPA830 and its circuit designs. This is particularly true for video and RF amplifier circuits where parasitic capacitance and inductance can play a major role on circuit performance. A SPICE model for the OPA830 is available through the TI web page (www.ti.com). The applications department is also available for design assistance. These models predict typical small signal AC, transient steps, DC performance, and noise under a wide variety of operating conditions. The models include the noise terms found in the electrical specifications of the data sheet. These models do not attempt to distinguish between the package types in their small-signal AC performance. OPERATING SUGGESTIONS OPTIMIZING RESISTOR VALUES Since the OPA830 is a unity-gain stable, voltage-feedback op amp, a wide range of resistor values may be used for the feedback and gain setting resistors. The primary limits on these values are set by dynamic range (noise and distortion) and parasitic capacitance considerations. For a noninverting unity-gain follower application, the feedback connection should be made with a direct short. Below 200Ω, the feedback network will present additional output loading which can degrade the harmonic distortion performance of the OPA830. Above 1kΩ, the typical parasitic capacitance (approximately 0.2pF) across the feedback resistor may cause unintentional band limiting in the amplifier response. A good rule of thumb is to target the parallel combination of R F and RG (see Figure 3) to be less than about 400Ω. The combined impedance RF || RG interacts with the inverting input capacitance, placing an additional pole in the feedback network, and thus a zero in the forward response. Assuming a 2pF total parasitic on the inverting node, holding R F || RG < 400Ω will keep this pole above 200MHz. By itself, this constraint implies that the feedback resistor RF can increase to several kΩ at high gains. This is acceptable as long as the pole formed by RF and any parasitic capacitance appearing in parallel is kept out of the frequency range of interest. In the inverting configuration, an additional design consideration must be noted. R G becomes the input resistor and therefore the load impedance to the driving source. If impedance matching is desired, R G may be set equal to the required termination value. However, at low inverting gains, the resultant feedback resistor value can present a significant load to the amplifier output. For example, an inverting gain of 2 with a 50Ω input matching resistor (= R G ) would require a 100Ω feedback resistor, which would contribute to output loading in parallel with the external load. In such a case, it would be preferable to increase both the RF and RG values, and then achieve the input matching impedance with a third resistor to ground (see Figure 9). The total input impedance becomes the parallel combination of R G and the additional shunt resistor. BANDWIDTH vs GAIN: NONINVERTING OPERATION Voltage-feedback op amps exhibit decreasing closed-loop bandwidth as the signal gain is increased. In theory, this relationship is described by the Gain Bandwidth Product (GBP) shown in the specifications. Ideally, dividing GBP by the noninverting signal gain (also called the Noise Gain, or NG) will predict the closed-loop bandwidth. In practice, this only holds true when the phase margin approaches 90°, as it does in high-gain configurations. At low gains (increased feedback factors), most amplifiers will exhibit a more complex response with lower phase margin. The OPA830 is compensated to give a slightly peaked response in a noninverting gain of 2 (see Figure 3). This results in a typical gain of +2 bandwidth of 110MHz, far exceeding that predicted by dividing the 110MHz GBP by 2. Increasing the gain will cause the phase margin to approach 90° and the bandwidth to more closely approach the predicted value of (GBP/NG). At a gain of +10, the 11MHz bandwidth shown in the Electrical Characteristics agrees with that predicted using the simple formula and the typical GBP of 110MHz. Frequency response in a gain of +2 may be modified to achieve exceptional flatness simply by increasing the noise gain to 3. One way to do this, without affecting the +2 signal gain, is to add an 2.55kΩ resistor across the two inputs, as shown in Figure 7. A similar technique may be used to reduce peaking in unity-gain (voltage follower) applications. For example, by using a 750Ω feedback resistor along with a 750Ω resistor across the two op amp inputs, the voltage follower response will be similar to the gain of +2 response of Figure 2. Further reducing the value of the resistor across the op amp inputs will further dampen the frequency response due to increased noise gain. The OPA830 exhibits minimal bandwidth reduction going to single-supply (+5V) operation as compared with ±5V. This minimal reduction is because the internal bias control circuitry retains nearly constant quiescent current as the total supply voltage between the supply pins is changed. INVERTING AMPLIFIER OPERATION All of the familiar op amp application circuits are available with the OPA830 to the designer. See Figure 9 for a typical inverting configuration where the I/O impedances and signal gain from Figure 1 are retained in an inverting circuit configuration. Inverting operation is one of the more common requirements and offers several performance benefits. It also allows the input to be biased at V S/2 without any headroom issues. The output voltage can be independently moved to be within the output voltage range with coupling capacitors, or bias adjustment resistors.
output and the capacitive load. output pin (see the Board Layout Guidelines section). typical characteristic curves. Figure 10. Noise Analysis Model specification for the op amp voltage noise alone.
/C0079/C0080/C0065/C0056/C0051/C0048 SBOS263F − AUGUST 2004 − REVISED AUGUST 2008 www.ti.com resistances), using worst-case +25°C input offset voltage and current specifications, gives a worst-case output offset voltage equal to: (NG = noninverting signal gain at DC) ±(NG × VOS(MAX) ) + (RF × IOS(MAX) ) = ±14.38mV A fine-scale output offset null, or DC operating point adjustment, is often required. Numerous techniques are available for introducing DC offset control into an op amp circuit. Most of these techniques are based on adding a DC current through the feedback resistor. In selecting an offset trim method, one key consideration is the impact on the desired signal path frequency response. If the signal path is intended to be noninverting, the offset control is best applied as an inverting summing signal to avoid interaction with the signal source. If the signal path is intended to be inverting, applying the offset control to the noninverting input may be considered. Bring the DC offsetting current into the inverting input node through resistor values that are much larger than the signal path resistors. This will insure that the adjustment circuit has minimal effect on the loop gain and hence the frequency response. THERMAL ANALYSIS Maximum desired junction temperature will set the maximum allowed internal power dissipation, as described below. In no case should the maximum junction temperature be allowed to exceed 150°C. Operating junction temperature (T J) is given by TA +P D × /C0113JA. The total internal power dissipation (PD ) is the sum of quiescent power (PDQ ) and additional power dissipated in the output stage (PDL ) to deliver load power. Quiescent power is simply the specified no-load supply current times the total supply voltage across the part. P DL will depend on the required output signal and load; though, for resistive loads connected to mid-supply (V S/2), PDL is at a maximum when the output is fixed at a voltage equal to VS/4 or 3VS/4. Under this condition, PDL =V S2/(16× R L), where R L includes feedback network loading. Note that it is the power in the output stage, and not into the load, that determines internal power dissipation. As a worst-case example, compute the maximum TJ using an OPA830 (SOT23-5 package) in the circuit of Figure 1 operating at the maximum specified ambient temperature of +85°C and driving a 150Ω load at mid-supply. Maximum T J = +85°C + (0.051W × 150°C/W) = 93°C. Although this is still well below the specified maximum junction temperature, system reliability considerations may require lower ensured junction temperatures. The highest possible internal dissipation will occur if the load requires current to be forced into the output at high output voltages or sourced from the output at low output voltages. This puts a high current through a large internal voltage drop in the output transistors. BOARD LAYOUT GUIDELINES Achieving optimum performance with a high-frequency amplifier like the OPA830 requires careful attention to board layout parasitics and external component types. Recommendations that will optimize performance include: a) Minimize parasitic capacitance to any AC ground for all of the signal I/O pins. Parasitic capacitance on the output and inverting input pins can cause instability: on the noninverting input, it can react with the source impedance to cause unintentional bandlimiting. To reduce unwanted capacitance, a window around the signal I/O pins should be opened in all of the ground and power planes around those pins. Otherwise, ground and power planes should be unbroken elsewhere on the board. b) Minimize the distance ( < 0.25”) from the power-supply pins to high-frequency 0.1µF decoupling capacitors. At the device pins, the ground and power-plane layout should not be in close proximity to the signal I/O pins. Avoid narrow power and ground traces to minimize inductance between the pins and the decoupling capacitors. Each power- supply connection should always be decoupled with one of these capacitors. An optional supply decoupling capacitor (0.1µF) across the two power supplies (for bipolar operation) will improve 2nd-harmonic distortion performance. Larger (2.2µF to 6.8 µF) decoupling capacitors, effective at lower frequency, should also be used on the main supply pins. These may be placed somewhat farther from the device and may be shared among several devices in the same area of the PC board. c) Careful selection and placement of external components will preserve the high-frequency perfor- mance. Resistors should be a very low reactance type. Surface-mount resistors work best and allow a tighter overall layout. Metal film or carbon composition axially-leaded resistors can also provide good high- frequency performance. Again, keep their leads and PC board traces as short as possible. Never use wire-wound type resistors in a high-frequency application. Since the output pin and inverting input pin are the most sensitive to parasitic capacitance, always position the feedback and series output resistor, if any, as close as possible to the output pin. Other network components, such as noninverting input termination resistors, should also be placed close to the package. Where double-side component mounting is allowed, place the feedback resistor directly under the package on the other side of the board between the output and inverting input pins. Even with a low parasitic capacitance shunting the external resistors, excessively high resistor values can create
significant time constants that can degrade performance. output into the terminating impedance. e) Socketing a high-speed part is not recommended. Figure 11. Internal ESD Protection
SBOS263F − AUGUST 2004 − REVISED AUGUST 2008 www.ti.com
Revision History
DATE REV PAGE SECTION DESCRIPTION 8/08 F 2 Absolute Maximum Ratings Changed Storage Temperature minimum value from −40°C to −65°C. 8/07 E 1 Features Changed 550V/ns to 550V/µs. NOTE : Page numbers for previous revisions may differ from page numbers in the current version.
Orderable Device Status(1) Package Type Package Drawing Pins Package Qty Eco Plan(2) Lead/Ball FinishMSL Peak Temp (3) OPA830ID ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA830IDBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA830IDBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA830IDBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA830IDBVTG4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA830IDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA830IDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA830IDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR (1)The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2)Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontentfor the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS):TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt):This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br):TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. PACKAGE OPTION ADDENDUM www.ti.com 16-Feb-2009 Addendum-Page 1
*All dimensions are nominal Device Package Type Package Drawing Pins SPQ Reel Diameter (mm) Reel Width W1 (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) W (mm) Pin1 Quadrant PACKAGE MATERIALS INFORMATION www.ti.com 20-May-2008 Pack Materials-Page 1
*All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) OPA830IDBVR SOT-23 DBV 5 3000 190.5 212.7 31.8 OPA830IDBVT SOT-23 DBV 5 250 190.5 212.7 31.8 OPA830IDR SOIC D 8 2500 346.0 346.0 29.0 PACKAGE MATERIALS INFORMATION www.ti.com 20-May-2008 Pack Materials-Page 2
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DLP® Products www.dlp.com Communications and www.ti.com/communications Telecom DSP dsp.ti.com Computers and www.ti.com/computers Peripherals Clocks and Timers www.ti.com/clocks Consumer Electronics www.ti.com/consumer-apps Interface interface.ti.com Energy www.ti.com/energy Logic logic.ti.com Industrial www.ti.com/industrial Power Mgmt power.ti.com Medical www.ti.com/medical Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Space, Avionics & www.ti.com/space-avionics-defense Defense RF/IF and ZigBee® Solutionswww.ti.com/lprf Video and Imaging www.ti.com/video Wireless www.ti.com/wireless-apps Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2010, Texas Instruments Incorporated