32-Channel, Current-Input Analog-to-Digital Converter datasheet (Rev. D)

Document overview

  • Manufacturer or author: Texas Instruments, Incorporated [SBAS331,D]
  • PDF pages: 35

Technical content

/c68/c83 ADC IN32 IN31 CLK CONV DIN_CFG CLK_CFG RESET Dual Switched Integrator Dual Switched Integrator Dual Switched Integrator Dual Switched Integrator Dual Switched Integrator Dual Switched Integrator Dual Switched Integrator Dual Switched Integrator VREF DVDDAVDD

0.1 F/c109

0.1 F/c1090.1 F/c109 /c68/c83 ADC /c68/c83 ADC /c68/c83 ADC DDC232 www.ti.com SBAS331D –AUGUST 2004–REVISED APRIL 2010 32-Channel,Current-Input Analog-to-DigitalConverter Check forSamples: DDC232 The DDC232 uses a +5V analogsupplyand a +2.7V1FEATURES to +3.6V digitalsupply. Operating over the 2• Single-ChipSolutiontoDirectlyMeasure 32 temperaturerange of 0°C to +70°C, the DDC232Low-Level Currents BGA-64 package is offeredin two versions:the

  • High-Precision,True IntegratingFunction DDC232C for low-power applications,and the DDC232CK when higherspeeds arerequired.• IntegralLinearity: ±0.025% ofReading ±1.0ppm ofFSR
  • Very Low Noise:5.3ppm ofFSR
  • Low Power: 7mW/channel
  • AdjustableFull-ScaleRange
  • AdjustableSpeed – Data Rate up to6kSPS – IntegrationTimes as low as 166.5ms
  • Daisy-ChainableSerialInterface
  • In-PackageBypass CapacitorsSimplifyPCB Design

APPLICATIONS

  • CT Scanner DAS
  • Photodiode Sensors
  • X-Ray DetectionSystems

DESCRIPTION

The DDC232 is a 20-bit,32-channel,current-input analog-to-digital(A/D) converter.Itcombines both current-to-voltageand A/D conversionso that32 separatelow-levelcurrentoutputdevices,such as photodiodes,can be directlyconnectedto itsinputs and digitized. For each of the 32 inputs,the DDC232 providesa dual-switchedintegratorfront-end.Thisconfiguration allowsforcontinuouscurrentintegration:whileone integratoris being digitizedby the onboard A/D converter,the otherisintegratingthe inputcurrent. Adjustableintegrationtimesrange from 166ms to1s, allowingcurrentsfrom fAs tomAs tobe continuously measured withoutstandingprecision. Protectedby US Patent#5841310The DDC232 has a serialinterfacedesigned for daisy-chainingin multi-devicesystems. Simply connectthe outputof one deviceto the inputof the nexttocreatethechain.Common clockingfeedsall thedevicesinthechainso thatthedigitaloverhead ina multi-DDC232systemisminimal. Pleasebe aware thatan importantnoticeconcerningavailability,standardwarranty,and use incriticalapplicationsofTexas Instrumentssemiconductorproductsand disclaimerstheretoappearsattheend ofthisdatasheet. 2Alltrademarksarethepropertyoftheirrespectiveowners. PRODUCTION DATA informationiscurrentas ofpublicationdate. Copyright© 2004–2010,Texas InstrumentsIncorporatedProductsconform to specificationsper the terms of the Texas Instrumentsstandardwarranty.Productionprocessingdoes not necessarilyincludetestingofallparameters.

SBAS331D –AUGUST 2004–REVISED APRIL 2010 www.ti.com This integratedcircuitcan be damaged by ESD. Texas Instrumentsrecommends thatallintegratedcircuitsbe handled with appropriateprecautions.Failuretoobserveproperhandlingand installationprocedurescan cause damage. ESD damage can rangefromsubtleperformancedegradationtocompletedevicefailure.Precisionintegratedcircuitsmay be more susceptibletodamage because verysmallparametricchanges couldcause thedevicenottomeet itspublishedspecifications. DEVICE FAMILY COMPARISON MAXIMUM DATA PACKAGE- PRODUCT # OF CHANNELS FULL-SCALE RATE POWER/CHANNEL LEAD DDC112 2 1000pC (1) 20kSPS 40mW SO-28 DDC112K 2 1000pC (1) 3.3kSPS 40mW TQFP-32 DDC114 4 350pC 3.3kSPS 13mW QFN-48 DDC118 8 350pC 3.3kSPS 13mW QFN-48 DDC316 16 12pC 100kSPS 28mW BGA-64 DDC232C 32 350pC 3.1kSPS 7mW BGA-64 DDC232CK 32 350pC 6.2kSPS 10mW BGA-64 (1) Usingexternalintegrationcapacitors. PACKAGE/ORDERING INFORMATION For the most currentpackage and orderinginformationsee the Package OptionAddendum at the end of this document,orvisitthedeviceproductfolderon www.ti.com. ABSOLUTE MAXIMUM RATINGS (1) AVDD toAGND –0.3Vto+6V DVDD toDGND –0.3Vto+3.6V AGND toDGND ±0.2V VREF InputtoAGND 2.0VtoAVDD + 0.3V AnalogInputtoAGND –0.3Vto+0.7V DigitalInputVoltagetoDGND –0.3VtoDVDD + 0.3V DigitalOutputVoltagetoDGND –0.3VtoAVDD + 0.3V OperatingTemperature 0°C to+70°C StorageTemperature –60°C to+150°C JunctionTemperature(TJ) +150°C (1) Stressesabove theseratingsmay cause permanentdamage. Exposuretoabsolutemaximum conditionsforextendedperiodsmay degradedevicereliability.These arestressratingsonly,and functionaloperationofthedeviceattheseorany otherconditionsbeyond thosespecifiedisnotimplied.

2 SubmitDocumentationFeedback Copyright© 2004–2010,Texas InstrumentsIncorporated

ProductFolderLink(s):DDC232

www.ti.com SBAS331D –AUGUST 2004–REVISED APRIL 2010

ELECTRICAL CHARACTERISTICS

AtTA = +25°C, AVDD = +5V, DVDD = +3.0V,VREF = +4.096V,tINT = 333ms forDDC232C or166ms forDDC232CK, Range 7,and continuousmode operation,unlessotherwisenoted. DDC232C DDC232CK PARAMETER TEST CONDITIONS MIN TYP MAX MIN TYP MAX UNIT ANALOG INPUT RANGE Range 0 12.5 12.5 pC Range 1 45 50 55 45 50 55 pC Range 2 90 100 110 90 100 110 pC Range 3 135 150 165 135 150 165 pC Range 4 180 200 220 180 200 220 pC Range 5 225 250 275 225 250 275 pC Range 6 270 300 330 270 300 330 pC Range 7 315 350 385 315 350 385 pC NegativeFull-ScaleRange –0.4% ofPositiveFull-ScaleRange –0.4% ofPositiveFull-ScaleRange pC DYNAMIC CHARACTERISTICS Data Rate 3 3.125 6 6.2 kSPS IntegrationTime,tINT ContinuousMode 320 1,000,000 160 1,000,000 ms NoncontinuousMode 50 50 ms System Clock(CLK) Clk_4x= 0 1 5 1 10 MHz Clk_4x= 1 4 20 4 40 MHz Data Clock(DCLK) 20 20 MHz ConfigurationClock(CLK_CFG) 20 20 MHz ACCURACY Noise,Low-LevelInput(1) C SENSOR (2)= 50pF 5.3 7 5.3 7 ppm ofFSR (3),rms IntegralLinearityError(4) ±0.025% Reading± 1.0ppm FSR, typ ±0.025% Reading± 1.0ppm FSR, typ ±0.05% Reading ± 1.5ppm FSR, max ±0.05% Reading ± 1.5ppm FSR, max Resolution No MissingCodes,Format= 1 20 19(5) Bits No MissingCodes,Format= 0 16 16 Bits InputBiasCurrent ±0.1 ±10 ±0.1 ±10 pA Range ErrorMatch(6) 0.1 0.5 0.1 0.5 % ofFSR Range SensitivitytoVREF VREF = 4.096±0.1V 1:1 1:1 OffsetError ±200 ±1000 ±200 ±1000 ppm ofFSR OffsetErrorMatch(6) ±100 ±100 ppm ofFSR DC BiasVoltage(7) Low-LevelInput(< 1% FSR) ±0.1 ±2 ±0.1 ±2 mV Power-SupplyRejectionRatio atDC 100 ±800 100 ±800 ppm ofFSR/V (1) Inputislessthan1% offull-scale. (2) C SENSOR isthecapacitanceseen attheDDC232 inputsfromwiring,photodiode,etc. (3) FSR isFull-ScaleRange. (4) A best-fitlineisused inmeasuringnonlinearity. (5) Outputword is20 bitswith19 bitsno missingcodes. (6) Matchingbetween sideA and sideB ofthesame input. (7) Voltageproducedby theDDC232 atitsinputthatisappliedtothesensor. Copyright© 2004–2010,Texas InstrumentsIncorporated SubmitDocumentationFeedback 3 ProductFolderLink(s):DDC232

SBAS331D –AUGUST 2004–REVISED APRIL 2010 www.ti.com ELECTRICAL CHARACTERISTICS (continued) AtTA = +25°C, AVDD = +5V, DVDD = +3.0V,VREF = +4.096V,tINT = 333ms forDDC232C or166ms for DDC232CK, Range 7,and continuousmode operation,unlessotherwisenoted. DDC232C DDC232CK PARAMETER TEST CONDITIONS MIN TYP MAX MIN TYP MAX UNIT PERFORMANCE OVER TEMPERATURE OffsetDrift ±0.5 5(8) ±0.5 5(8) ppm ofFSR/°C OffsetDriftStability ±0.2 2(8) ±0.2 2(8) ppm ofFSR/minute DC BiasVoltageDrift(9) ±3 ±3 mV/°C InputBiasCurrentDrift TA = +25°C to+45°C 0.01 1(8) 0.01 1(8) pA/°C Range Drift(10) 25 50 25 50 ppm/°C Range DriftMatch(11) ±5 ±5 ppm/°C REFERENCE InputCurrent(12) AverageValuewithtINT = 333ms 325 mA AverageValuewithtINT = 166.5ms 650 mA DIGITAL INPUT/OUTPUT LogicLevels VIH 0.8DVDD DVDD + 0.1 0.8DVDD DVDD + 0.1 V VIL –0.1 0.2DVDD –0.1 0.2DVDD V VOH IOH = –500mA DVDD – 0.4 DVDD – 0.4 V VOL IOL = 500mA 0.4 0.4 V InputCurrent(IIN) 0 < VIN < DVDD ±10 ±10 mA Data Format(13) StraightBinary StraightBinary POWER-SUPPLY REQUIREMENTS SupplyCurrent AnalogCurrent 41 60 mA DigitalCurrent 3.7 8.0 mA TotalPower Dissipation 224 288 290 mW Per ChannelPower Dissipation 7 9 10 mW/Channel (8) Ensuredby design,notproductiontested. (9) Voltageproducedby theDDC232 atitsinputthatisappliedtothesensor. (10)Range driftdoes notincludeexternalreferencedrift. (11)Matchingbetween sideA and sideB ofthesame input. (12)InputreferencecurrentdecreaseswithincreasingtINT (seetheVoltageReferencesection,page 10). (13)Data formatisStraightBinarywitha smalloffset.The number ofbitsintheoutputword iscontrolledby theFormatbit.

4 SubmitDocumentationFeedback Copyright© 2004–2010,Texas InstrumentsIncorporated

ProductFolderLink(s):DDC232

IN7 IN9 IN11IN6IN5 IN8 IN10 IN12 IN19 IN29 IN31IN18IN17 IN20 IN30 IN32 IN3 IN13 IN15IN2IN1 IN4 IN14 IN16 AGND AGND AGNDAGNDQGND AGND AGND AGND AVDD AGND VREFAVDDAGND AVDD DGND VREF CLK DOUT DINDGNDDCLK NC DGND CONV IN23 IN25 IN27IN22IN21 IN24 IN26 IN28 Rows CLK_CFG DGND DVDDDIN_CFGDVALID DGND RESET DGND BGA DDC232 www.ti.com SBAS331D –AUGUST 2004–REVISED APRIL 2010 PIN CONFIGURATION PIN DESCRIPTIONS PIN LOCATION FUNCTION DESCRIPTION IN1–32 Rows 1–4 AnalogInput AnalogInputsforChannels1 to32 QGND H5 Analog QuietAnalogGround AGND G5, F5,E5,D5, C5, B5,A5,D6, H6 Analog AnalogGround DGND A7,C6, D7, E7,C8, G8 Digital DigitalGround AVDD E6,F6,G6 Analog AnalogPower Supply,+5V Nominal VREF A6,B6 AnalogInput ExternalVoltageReferenceInput,+4.096V Nominal DVALID H7 DigitalOutput Data ValidOutput,ActiveLow DIN_CFG G7 DigitalInput ConfigurationRegisterData Input CLK_CFG F7 DigitalInput ConfigurationRegisterClockInput RESET C7 DigitalInput DigitalReset,ActiveLow DVDD B7 Digital DigitalPower Supply,3.3VNominal CONV A8 DigitalInput ConversionControlInput;0 = Integrateon SideB,1 = Integrateon SideA DIN B8 DigitalInput SerialData Input DOUT D8 DigitalOutput SerialData Output NC E8 No Connect Do notconnect;must be leftfloating. CLK F8 DigitalInput MasterClockInput DCLK H8 DigitalInput SerialData ClockInput Copyright© 2004–2010,Texas InstrumentsIncorporated SubmitDocumentationFeedback 5 ProductFolderLink(s):DDC232

Noise□(ppm□of□FSR,□rms) 150 140 130 120 110 100 200 300 400 500 600 700 800 900 1000 C (pF)SENSOR Range□1 Range□2 Range□7 DDC232 SBAS331D –AUGUST 2004–REVISED APRIL 2010 www.ti.com TYPICAL CHARACTERISTICS AtTA = +25°C, unlessotherwiseindicated. NOISE vs C SENSOR Figure1. Table1.NOISE vs C SENSOR (ppm ofFSR, rms) NOISE (ppm ofFSR, rms)CSENSOR (pF) Range 0 Range 1 Range 2 Range 3 Range 4 Range 5 Range 6 Range 7 150 100 29 16 12 10 8.7 7.8 7.2 330 180 50 27 19 15 13 11 10 470 250 67 36 25 19 16 14 12 1000 520 130 57 49 37 30 26 22 Table2.NOISE vs C SENSOR (fC,rms) NOISE (fC,rms)CSENSOR (pF) Range 0 Range 1 Range 2 Range 3 Range 4 Range 5 Range 6 Range 7 Table3.NOISE vs C SENSOR (electrons,rms) NOISE (electrons,rms)CSENSOR (pF) Range 0 Range 1 Range 2 Range 3 Range 4 Range 5 Range 6 Range 7 0 2100 2840 3930 5140 6490 7800 9170 10400 22 2960 3740 4930 6080 7240 8580 9920 11100 47 3970 4680 6110 7200 8360 9510 10800 12000 68 4600 5610 6860 7950 9110 10200 11400 12600 100 5770 6860 8110 9260 10300 11500 12700 13700 150 7800 9050 9980 11200 12400 13500 14600 15700 330 14000 15600 16800 17700 18700 20200 20500 21800 470 19500 20900 22400 23400 23700 24900 26200 26200 1000 40500 40500 35500 45800 46100 46800 48600 48000

6 SubmitDocumentationFeedback Copyright© 2004–2010,Texas InstrumentsIncorporated

ProductFolderLink(s):DDC232

Figure 2. The device contains32 identicalinput integratorsfromone sideoftheinputswillbe digitized integratorsare switched to 16 delta-sigma(∆Σ) lowwhen theshiftregistercontainsvaliddata.

12.5pF VREF Range[2]□Bit Range[1]□Bit Range[0]□Bit SRESET SREF2 SADC1A SINTA SREF1 IN1 ESD Protection Diodes Input Current Integrator□B□(same□as□A) Integrator□A Photodiode 3pF T o□Converter SINTB Adjustable□Feedback□Capacitors□(C )F DDC232 SBAS331D –AUGUST 2004–REVISED APRIL 2010 www.ti.com DEVICE OPERATION operationalamplifier.At the beginning of a conversion,the switchesSA/D, SINTA, SINTB, SREF1 , Basic IntegrationCycle SREF2 ,and SRESET areset(seeFigure4). The topologyof the frontend of the DDC232 isan At the completionof an A/D conversion,the charge analog integratoras shown in Figure 3. In this on the integrationcapacitor(CF) isresetwithSREF1 diagram,only inputIN1 is shown. The inputstage and SRESET (see Figure4 and Figure5a).This is consistsof an operationalamplifier,a selectable done during reset.In thismanner, the selected feedback capacitornetwork (CF), and several capacitorischargedtothereferencevoltage,VREF. switchesthatimplement the integrationcycle.The Once theintegrationcapacitorischarged,SREF1 and timingrelationshipsof allof the switchesshown in SRESET are switched so that VREF is no longer Figure 3 are illustratedin Figure 4. Figure 4 connected to the amplifiercircuitwhileitwaitsto conceptualizesthe operationof the integratorinput begin integrating(see Figure 5b). With the rising stageoftheDDC232 and shouldnotbe used as an edge of CONV, SINTA closes,which begins the exacttimingtoolfordesign. integrationofsideA. Thisprocessputstheintegrator stageintoitsintegratemode (seeFigure5c).See Figure5 forthe blockdiagrams of the reset, integrate,wait,and convertstatesof the integrator Charge from the inputsignalis collectedon the sectionof the DDC232. This internalswitching integrationcapacitor,causingthe voltageoutputof networkiscontrolledexternallywiththe convertpin theamplifiertodecrease.The fallingedge ofCONV (CONV) and the system clock(CLK).For the best stops the integrationby switchingthe inputsignal noiseperformance,CONV must be synchronizedwith from sideA to sideB (SINTA and SINTB).Priorto the therisingedge ofCLK. Itisrecommended thatCONV fallingedge of CONV, the signalon side B was togglewithin±10ns oftherisingedge ofCLK. convertedby theA/D converterand resetduringthe Figure3. Basic IntegrationConfigurationforInput1

8 SubmitDocumentationFeedback Copyright© 2004–2010,Texas InstrumentsIncorporated

ProductFolderLink(s):DDC232

Integrator A WaitConvert WaitConvertIntegrate SREF1 SREF2 SINTA SINTB SRESET CONV CLK W ait Reset W ait Reset To ConverterSRESET SREF2 SA/D VREF SREF1 SINT IN CF a) Reset Configuration To ConverterSRESET SREF2 SA/D VREF SREF1 SINT IN CF c) Integrate Configuration To ConverterSRESET SREF2 SA/D VREF SREF1 SINT IN CF d) Convert Configuration To ConverterSRESET SREF2 SA/D VREF SREF1 SINT IN CF b) Wait Configuration DDC232 www.ti.com SBAS331D –AUGUST 2004–REVISED APRIL 2010 Figure4. IntegrationTiming (seeFigure3) Figure5. Four ConfigurationsoftheFront-EndIntegrators Copyright© 2004–2010,Texas InstrumentsIncorporated SubmitDocumentationFeedback 9 ProductFolderLink(s):DDC232

0.10/c109F +5V 10k/c87 10/c109F 4 0.10/c109F 10/c109F OPA350 0.47/c109F +5V To VREF Pin on the DDC232 REF3140 DDC232 SBAS331D –AUGUST 2004–REVISED APRIL 2010 www.ti.com charge needed by the ∆Σ converter.For anIntegrationCapacitors integrationtimeof333ms,thischargetranslatestoan Consequently,allinputsand bothsidesofeach input ItiscriticalthatVREF be stableduringthe differentwillalways have the same full-scalerange.Table 4 modes ofoperation(seeFigure5).The ∆Σ convertershows the capacitorvalue selectedforeach range measures the voltageon the integratorwithrespectselection. to VREF. Since the integratorcapacitorsare initially resetto VREF, any drop inVREF from the timetheTable4.Range Selection capacitorsare resetto the timewhen the converter measures the integratoroutput willintroduceanRANGE CONTROL BITS INPUT C F RANGE offset.ItisalsoimportantthatVREF be stableover RANGE Range[2] Range[1] Range[0] (pF,typ) (pC,typ) longerperiodsof time because changes in VREF 0 0 0 0 3 –0.04to12.5 corresponddirectlytochanges inthefull-scalerange. 1 0 0 1 12.5 –0.2to50 Finally,VREF should introduceas littleadditional 2 0 1 0 25 –0.4to100 noiseas possible. 3 0 1 1 37.5 –0.6to150 For these reasons,itisstronglyrecommended that 4 1 0 0 50 –0.8to200 the externalreferencesource be bufferedwith an 5 1 0 1 62.5 –0.1to250 operationalamplifier,as shown in Figure6. In this 6 1 1 0 75 –1.2to300 circuit,the voltagereferenceis generated by a 7 1 1 1 87.5 –1.4to350 +4.096V reference.A low-passfilterto reduce noise connects the referenceto an operationalamplifier configuredas a buffer.Thisamplifiershouldhave lowVoltageReference noise and input/outputcommon-mode ranges that The externalvoltagereferenceisused to resetthe supportVREF. Even though the circuitin Figure6 integrationcapacitorsbefore an integrationcycle mightappear to be unstabledue to the largeoutput begins.Itisalsoused by the∆Σ converterwhilethe capacitors,it works well for most operational converteris measuring the voltagestoredon the amplifiers.It is not recommended that series integratorsafteran integrationcycleends.Duringthis resistancebe placedin the outputlead to improve sampling,the externalreferencemust supply the stabilitysincethiscan cause a drop inVREF, which produceslargeoffsets. Figure6. Recommended ExternalVoltageReferenceCircuitforBest Low-Noise Operation

10 SubmitDocumentationFeedback Copyright© 2004–2010,Texas InstrumentsIncorporated

ProductFolderLink(s):DDC232

− 10 − 20 − 30 − 40 − 50 0.1 tINT 1001 tINT Frequency Gain (dB) tINT tINT DDC232 www.ti.com SBAS331D –AUGUST 2004–REVISED APRIL 2010 Frequency Response CONFIGURATION REGISTER The frequencyresponseoftheDDC232 issetby the Some aspectsof deviceoperationare controlledby front-endintegratorsand is that of a traditional the onboard configurationregister.The DIN_CFG, continuoustimeintegrator,as shown inFigure7.By CLK_CFG, and RESET pinsareused towritetothis adjustingtINT, the user can change the 3dB register.When beginninga writeoperation,hold bandwidth and the locationof the notches in the CONV low and strobeRESET; see Figure8. Then response. The frequency response of the ∆Σ beginshiftingintheconfigurationdataon DIN_CFG. converterthatfollowsthefront-endintegratorisofno Data are writtento the configurationregistermost consequence because the convertersamples a held significantbitfirst.The dataare internallylatchedon signalfrom the integrators.That is,the inputto the the fallingedge of CLK_CFG. Partialwritesto the ∆Σ converterisalwaysa DC signal.Sincetheoutput configurationregisterare notallowed— make sureto ofthefront-endintegratorsaresampled,aliasingcan send all12 bitswhen updatingtheregister. occur.Whenever the frequencyof the inputsignal Optionalreadback of the configurationregisterisexceeds one-halfofthesamplingrate,thesignalwill availableimmediatelyafter the write sequence.foldback down tolowerfrequencies. During readback, the 12-bit configurationdata followedby a 4-bitrevisionID and thetestpatternare shiftedout on the DOUT pin on the risingedge of DCLK. NOTE: Wth Format = 1,thetestpatternis304 bits, withonlythelast72 bitsnon-zero.Thissequence of outputsis repeated twice for each DDC232 and daisy-chainingissupportedinconfigurationreadback. Table 5 shows the testpatternconfigurationduring readback. Table 6 shows the timing for the configurationregisterread and write operations. StrobeCONV tobeginnormaloperation. Table5.TestPatternDuring Readback TEST PATTERN TOTAL Format BIT (Hex) READBACK BITS 0 30F066012480F6h 512 Figure7. Frequency Response 1 30F066012480F69055h 640 Copyright© 2004–2010,Texas InstrumentsIncorporated SubmitDocumentationFeedback 11 ProductFolderLink(s):DDC232

Write Configuration Register Data Configuration Register Operations Test Pattern Read Configuration Register and Test Pattern RESET CLK_CFG DIN_CFG DCLK DOUT CONV Normal Operation tWTWR tWTRST MSB LSB MSB LSB tSTCF tRST tHDCF DDC232 SBAS331D –AUGUST 2004–REVISED APRIL 2010 www.ti.com NOTE: CLK must be runningduringConfigurationRegisterwriteand readoperations. Figure8. ConfigurationRegisterWriteand Read Operations Table6.Timing fortheConfigurationRegisterRead/Write SYMBOL DESCRIPTION MIN TYP MAX UNITS tWTRST WaitRequiredfromResetHightoFirstRisingEdge ofCLK_CFG 2 ms WaitRequiredfromLastCLK-CFG ofWriteOperationtotWTWR 2 msFirstCLK_CFG ofRead Operation tSTCF Set-UpTime fromDIN_CFG toFallingEdge ofCLK_CFG 10 ns tHDCF HoldTime forDIN_CFG AfterFallingEdge ofCLK_CFG 10 ns tRST PulseWidthforRESET Active 1 ms

12 SubmitDocumentationFeedback Copyright© 2004–2010,Texas InstrumentsIncorporated

ProductFolderLink(s):DDC232

www.ti.com SBAS331D –AUGUST 2004–REVISED APRIL 2010 Table7.ConfigurationRegister Bit11 Bit10 Bit9 Bit8 Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 Range[2] Range[1] Range[0] Format Version Clk_4x 0 0 0 0 0 Test Bits11–9 Range[2:0].Full-scalerange. 000:12.5pC 100:200pC 001:50pC 101:250pC 010:100pC 110:300pC 011:150pC 111:350pC (default) Bit8 Format.Data outputformat.Thisbitselectshow many bitsareused inthedataoutputword. 0:16-BitOutput 1:20-BitOutput(default) Bit7 Version.Deviceversionsetting. Must be setto'0'forDDC232C Must be setto'1'forDDC232CK Bit6 Clk_4x.System clockdivider.The Clk_4xinputenablesan internaldivideron thesystemclock. When Clk_4x= 1,thesystemclockisdividedby 4.Thisallowsa 4X fastersystemclock,which inturnprovidesa finerquantizationoftheintegrationtimebecause theCONV signalneeds tobe synchronizedwiththesystemclockforthebestperformance. 0:InternalClockDivider= 1 (default) 1:InternalClockDivider= 4 Clk_4x BIT CLK DIVIDER VALUE CLK FREQUENCY INTERNAL CLOCK FREQUENCY 0 1 5MHz 5MHz 1 4 20MHz 5MHz Bits5–1 These bitsmust be setto'0'. Bit0 Test.Diagnostictestmode enable.When Testmode isused,theinputs(IN1throughIN32)are disconnectedfromtheDDC232 integratorstoenabletheusertomeasure a zeroinputsignal regardlessofthecurrentsuppliedtotheinputs.Testmode workswithbothContinuousand Noncontinuousmodes. 0:TestMode Off(default) 1:TestMode On Copyright© 2004–2010,Texas InstrumentsIncorporated SubmitDocumentationFeedback 13 ProductFolderLink(s):DDC232

RESET > 1µs DDC232 SBAS331D –AUGUST 2004–REVISED APRIL 2010 www.ti.com DIGITAL INTERFACE DVALID eliminates any concern about this fundamentallyindependent of the data retrieval Reset (RESET)process. Consequently, the CLK and DCLK frequenciesneed not be the same, though forbest The DDC232 isresetasynchronouslyby takingthe performance,itishighlyrecommended thattheybe RESET inputlow,as shown inFigure9. Make sure derivedfrom the same clockingsource to keep the thereleasepulseisatleast1ms wide.Afterresetting phase relationshipconstant.DIN isonlyused when the DDC232, waitat leastfourconversionsbefore multipleconvertersare cascaded and shouldbe tied using the data.Itis very importantthatRESET is to DGND otherwise.Depending on tINT, CLK, and glitch-freetoavoidunintentionalresets. DCLK, it is possible to daisy-chainmultiple converters.Thisgreatlysimplifiestheinterconnection and routingofthedigitaloutputsinthoseapplications where a largenumber of convertersare needed. Configurationof the DDC232 isset by a dedicated registeraddressed using the DIN_CFG and CLK_CFG pins. Figure9. Reset TimingSystem and Data Clocks (CLK and CONV) The system clockissuppliedto CLK and the data Conversion RateclockissuppliedtoDCLK. Itisrecommended thatthe The conversionrate of the DDC232 is set by aCLK pin be drivenby a free-runningclocksource combinationof the integrationtime (determinedby(thatis, do not startand stop CLK between the user) and the speed of the A/D conversionconversions).Make sure the clock signalsare process.The A/D conversiontime is primarilyaclean— avoid overshoot or ringing.For best functionof the system clock(CLK) speed.One A/Dperformance,generateboth clocksfrom the same conversioncycleencompasses theconversionoftwoclocksource.DCLK shouldbe disabledby takingit signals(one sideofeach dualintegratorfeedingthelow afterthe data has been shiftedout or while modulator)and the reset time for each of theCONV istransitioning. In the event thatthe A/D conversiontakes longer thantheintegrationtime,theDDC232 willswitchintoData Valid(DVALID) DVALID signalwillhave a random phase relationship with CONV. This uncertaintyis ±1/fCLK . Polling

14 SubmitDocumentationFeedback Copyright© 2004–2010,Texas InstrumentsIncorporated

ProductFolderLink(s):DDC232

5CONV • mbsy CONV • mbsy State Diagram Notation: CONV • mbsy = CONV high AND mbsy active. CONV|mbsy = CONV high OR mbsy active. CONV • mbsy CONV • mbsy CONV • mbsy CONV • mbsy CONV CONV Int B/Meas A Cont Ncont Ncont Int A Cont Ncont Ncont Int B Cont

6 CONV

CONV|mbsy CONV|mbsy DDC232 www.ti.com SBAS331D –AUGUST 2004–REVISED APRIL 2010 Continuous and Noncontinuous Operational Four signalsare used to controlprogressionaround Modes the state diagram: CONV, mbsy, and their measurement/reset/auto-zero(m/r/az)cycle is in progress. During the Continuous(Cont)mode, mbsy is not activewhen CONV toggles.The nonintegratingside isalways ready to beginintegratingwhen the other sidefinishesitsintegration.Consequently,monitoring the currentstatusof CONV isallthatisneeded to know the current state.Cont mode operation correspondstostates3 to6.Two ofthestates,3 and 6, only perform an integration(thatis,no m/r/az cycle). mbsy becomes importantwhen operatingin the Noncontinuous(Ncont)mode (states1,2,7,and 8). Whenever CONV istoggledwhilembsy isactive,the DDC232 willenteror remain ineitherNcont state1 (or8).Aftermbsy goes inactive,state2 (or7) is entered.Thisstatepreparestheappropriatesidefor integration.In the Ncont states,the inputsto the DDC232 aregrounded. One interestingobservationfromthestatediagramis thatthe integrationsalways alternatebetween sides A and B. This relationshipholds for any CONV patternand isindependentofthemode. States2 and 7 ensurethisrelationshipduringtheNcontmode. When power is firstappliedto the DDC232, the beginningstateis either1 or 8, depending on the initiallevelof CONV. For CONV held high at power-up,the beginningstateis1. Conversely,for CONV heldlow atpower-up,thebeginningstateis8. Ingeneral,thereisa symmetry inthestatediagram between states1–8, 2–7, 3–6, and 4–5. Inverting CONV resultsinthestatesprogressingthroughtheirFigure10. Integrate/MeasureStateDiagram symmetricalmatch. Table8.StateDescriptions STATE MODE DESCRIPTION Completem/r/azofsideA,thensideB (ifpreviousstateisstate4).Initialpower-upstate1 Ncont when CONV isinitiallyheldhigh. 2 Ncont PreparesideA forintegration. 3 Cont Integrateon sideA. 4 Cont Integrateon sideB;m/r/azon sideA. 5 Cont Integrateon sideA;m/r/azon sideB. 6 Cont Integrateon sideB. 7 Ncont PreparesideB forintegration. Completem/r/azofsideB,thensideA (ifpreviousstateisstate5).Initialpower-upstate8 Ncont when CONV isinitiallyheldlow. Copyright© 2004–2010,Texas InstrumentsIncorporated SubmitDocumentationFeedback 15 ProductFolderLink(s):DDC232

Integrate AIntegrate B Integrate B Integrate A m/r/az B m/r/az A m/r/az B CONV State Integration Status m/r/az Status mbsy DVALID tMRAZ tCMDR t = 0 Power−Up Side B Data Side A Data Side B Data DDC232 SBAS331D –AUGUST 2004–REVISED APRIL 2010 www.ti.com TIMING EXAMPLES topsignalisCONV and issuppliedby theuser.TheContinuous Mode next lineindicatesthe currentstatein the state Figure11 shows a few integrationcyclesbeginning datatothecorrespondingintegration. withinitialpower-up fora Cont mode example.The Figure11. Continuous Mode Timing Table9.Timing SpecificationsGeneralizedinCLK Periods VALUE (CLK PeriodswithClk_4x = 0) SYMBOL DESCRIPTION DDC232C DDC232CK tMRAZ Continuousmode, m/r/azcycle 1552 ± 2 1612 ± 2 tCMDR Continuousmode, dataready 1382 ± 2 1382 ± 2

16 SubmitDocumentationFeedback Copyright© 2004–2010,Texas InstrumentsIncorporated

ProductFolderLink(s):DDC232

Odd Channels (Internal) A/D Conversion Even Channels (Internal) tIRST tADRST tADCONV DDC232 www.ti.com SBAS331D –AUGUST 2004–REVISED APRIL 2010 In Figure11, the firststateis Ncont state8. The Ncont modes describedearlierintheContinuousand DDC232 alwayspowers up intheNcont mode. Inthis NoncontinuousOperationalModes section.DVALID case, the firststateis 8 because CONV is initially goes low afterCONV togglesintimetCMDR ,indicating low.Afterthefirsttwo states,Cont mode operationis thatdataarereadytobe retrieved. reachedand thestatesbegintogglingbetween 4 and See Figure12 forthe timingdiagram of the internal5. From now on, the inputis being continuously operations occurring during Continuous modeintegrated,eitheron side A or side B. The time operation.Table10 givesthetimingspecificationsofneeded forthe m/r/azcycle,tMRAZ , isthe same time the internaloperationsoccurringduringContinuousthatdeterminestheboundarybetween theCont and mode operation. Figure12. InternalOperationinContinuous Mode Timing Table10.Timing CharacteristicsfortheInternalOperationinContinuous Mode DDC232C DDC232CK (CLK = 5MHz, Clk_4x = 0) (CLK = 10MHz, Clk_4x = 0) SYMBOL DESCRIPTION MIN TYP MAX MIN TYP MAX UNITS tINT IntegrationPeriod(continuousmode) 320 1,000,000 160 1,000,000 ms tADCONV A/D ConversionTime (internallycontrolled) 135.6 68 ms tADRST A/D ConversionResetTime (internallycontrolled) 3.2 2.2 ms tIRST IntegratorResetTime (internallycontrolled) 36 21.8 ms Copyright© 2004–2010,Texas InstrumentsIncorporated SubmitDocumentationFeedback 17 ProductFolderLink(s):DDC232

Side B Data ReadySide A Data Ready Start Integration Side AStart Integration Side A CONV A/D Conversion Odd Channels A/D Conversion Even Channels DVALID tADCONV tADCONV tINT tINT tADRST tNCIRST tNCRL CONV A/D Conversion Odd Channels A/D Conversion Even Channels DVALID Release State End Integration Side B Start Integration Side A End Integration Side A Wait State Side B Data Ready Side A Data Ready Start Integration Side BStart Integration Side B DDC232 SBAS331D –AUGUST 2004–REVISED APRIL 2010 www.ti.com Noncontinuous Mode Figure13 and Figure14 illustrateoperationinNoncontinuousmode. Figure13. Conversion DetailfortheInternalOperationofNoncontinuous Mode withSide A IntegratedFirst Table11.Timing CharacteristicsfortheInternalOperationinNoncontinuous Mode DDC232C DDC232CK (CLK = 5MHz, Clk_4x = 0) (CLK = 10MHz, Clk_4x = 0) SYMBOL DESCRIPTION MIN TYP MAX MIN TYP MAX UNITS tINT IntegrationTime (Noncontinuousmode) 50 1,000,000 50 1,000,000 ms tADCONV A/D ConversionTime (internallycontrolled) 135.6 67.8 ms tADRST A/D ConversionResetTime (internallycontrolled) 3.2 1.6 ms NoncontinuousMode IntegratorResetTime (internally mstNCIRST 30.4 15.2controlled) tNCRL ReleaseTime 0.4 0.2 ms tNCDR1 1stNoncontinuousMode Data Ready 276.5 138.2 ms tNCDR2 2nd NoncontinuousMode Data Ready 304.8 152.4 ms BLANKSPACE Figure14. InternalOperationNoncontinuous Mode Timing withSide B IntegratedFirst

18 SubmitDocumentationFeedback Copyright© 2004–2010,Texas InstrumentsIncorporated

ProductFolderLink(s):DDC232

m/r/az B m/r/az A m/r/az B m/r/az A m/r/az B Integrate A Integrate B Int AInt A Int B CONV 42143 3State mbsy m/r/az Status Integration Status m/r/az A m/r/az B m/r/az A Int BInt A Integrate A Integrate B Noncontinuous Continuous DDC232 www.ti.com SBAS331D –AUGUST 2004–REVISED APRIL 2010 isincreasedso thattINT isalways≥ tMRAZ as shown inChanging Between Modes Figure16 (see Figure13 and Table 11, page 18). Changing fromNcont toCont mode occurswhen tINT Figure15. Changing from Continuous Mode toNoncontinuous Mode Figure16. Changing from Noncontinuous Mode toContinuous Mode Copyright© 2004–2010,Texas InstrumentsIncorporated SubmitDocumentationFeedback 19 ProductFolderLink(s):DDC232

Input□32 MSB Input LSB Input MSB Input□5 LSB Input□4 MSB Input□2 LSB Input□1 MSB Input□1 LSB Input□32 MSB DCLK DOUT DDC232 SBAS331D –AUGUST 2004–REVISED APRIL 2010 www.ti.com Table12.IdealOutput Code (1)vs InputSignalDATA FORMAT INPUT IDEAL OUTPUT CODE IDEAL OUTPUT CODEThe serialoutputdataareprovidedinan offsetbinary SIGNAL FORMAT = 1 FORMAT = 0code as shown in Table 12. The Format bitin the ≥ 100% FS 1111 1111 1111 1111 1111 1111 1111 1111 1111configurationregisterselectshow many bitsareused 0.001531% FS 0000 0001 0000 0001 0000 0000 0001 0000 0001in the outputword. When Format = 1, 20 bitsare 0.001436% FS 0000 0001 0000 0000 1111 0000 0001 0000 0000used. When Format = 0, the lower 4 bitsare 0.000191% FS 0000 0001 0000 0000 0010 0000 0001 0000 0000truncatedso thatonly16 bitsareused.Note thatthe LSB sizeis16 timesbiggerwhen Format = 0. An 0.000096% FS 0000 0001 0000 0000 0001 0000 0001 0000 0000 offsetis includedin the output to allow slightly 0% FS 0000 0001 0000 0000 0000 0000 0001 0000 0000 negativeinputs(forexample,from board leakages) –0.3955% FS 0000 0000 0000 0000 0000 0000 0000 0000 0000 fromclippingthereading.Thisoffsetisapproximately 0.4% ofthepositivefull-scale. (1) Excludestheeffectsofnoise,INL,offset,and gainerrors. BLANKSPACE DATA RETRIEVAL Make sure not to retrievedata around changes in InboththeContinuousand Noncontinuousmodes of CONV because thiscan introducenoise.Stop activity operation,the data from the lastconversionare on DCLK at least10ms before or aftera CONV availableforretrievalon the fallingedge of DVALID transition. (seeFigure17 and Table13).Data areshiftedouton Settingthe Format bit= 0 (16-bitoutputword) willthefallingedge ofthedataclock,DCLK. reducethetimeneeded toretrievedataby 20% since therearefewerbitstoshiftout.Thiscan be usefulin multichannelsystems requiringonly 16 bits of resolution. Figure17. DigitalInterfaceTiming forData RetrievalFrom a SingleDDC232 Table13.Timing forDDC232 Data Retrieval SYMBOL DESCRIPTION MIN TYP MAX UNITS tPDCDV PropagationDelayfromFallingEdge ofCLK toDVALID Low 10 ns tPDDCDV PropagationDelayfromFallingEdge ofDCLK toDVALID High 5 ns tHDDODV HoldTime thatDOUT isValidBeforetheFallingEdge ofDVALID 400 ns tHDDODC HoldTime thatDOUT isValidAfterFallingEdge ofDCLK 4 ns tPDDCDO (1) PropagationDelayfromFallingEdge ofDCLK toValidDOUT 25 ns (1) Witha maximum loadofone DDC232 (4pFtypical)withan additionalloadof5pF.

20 SubmitDocumentationFeedback Copyright© 2004–2010,Texas InstrumentsIncorporated

ProductFolderLink(s):DDC232

IN32 IN31 IN30 IN29 IN4 IN3 IN2 IN1 IN32 IN31 IN30 IN29 IN4 IN3 IN2 IN1 IN32 IN31 IN30 IN29 IN4 IN3 IN2 IN1 IN32 IN31 IN30 IN29 IN4 IN3 IN2 IN1 128 127 126 125 100 99 98 97 96 95 94 93 68 67 66 65 64 63 62 61 36 35 34 33 32 31 30 29 4 3 2 1Sensor DINDOUT DDC232 DV ALID DCLK Data Retrieval Output Data Clock DINDOUT DDC232 DV ALID DCLK DINDOUT DDC232 DV ALID DCLK DINDOUT DDC232 DV ALID DCLK CLK DVALID DCLK DIN tSTDIDC tHDDIDC DOUT Input 128 MSB Input 128 MSB Input 128 LSB Input 127 MSB Input□3 LSB Input□2 MSB Input□2 LSB Input□1 MSB Input□1 LSB DDC232 www.ti.com SBAS331D –AUGUST 2004–REVISED APRIL 2010 Cascading MultipleConverters Figure19 shows the timingdiagram when the DIN inputisused todaisy-chainseveraldevices.Table14MultipleDDC232 unitscan be connected in serial givesthe timingspecificationfordata retrievalusingconfiguration;see Figure18. DIN. DOUT can be used withDIN to daisy-chainmultiple DDC232 devicestogetherto minimizewiring.In this mode of operation,the serialdata outputisshifted throughmultipleDDC232s; see Figure18. Figure18. Daisy-ChainedDDC232s Figure19. Timing When Using DDC232 DIN Function;See Figure18 Table14.Timing forDDC232 Data RetrievalUsing DIN SYMBOL DESCRIPTION MIN TYP MAX UNITS tSTDIDC Set-UpTime fromDIN toFallingEdge ofDCLK 10 ns tHDDIDC HoldTime forDIN AfterFallingEdge ofDCLK 10 ns Copyright© 2004–2010,Texas InstrumentsIncorporated SubmitDocumentationFeedback 21 ProductFolderLink(s):DDC232

tINT /C0042/C0466tCMDR /C0041tSDCV /C0467 (20 /C003232)/C0116DCLK 1000/C0109s /C0042286.8/C0109s (640)(100ns) /C004311.14/C017911 DDC232 Side B Data Side A Data tINT tINT tCMDR tSDCV CONV DVALID DCLK DOUT DDC232 SBAS331D –AUGUST 2004–REVISED APRIL 2010 www.ti.com RETRIEVAL BEFORE CONV TOGGLES (CONTINUOUS MODE) (1) Data retrievalbefore CONV togglesis the most NOTE: (16 × 32)tDCLK isused forFormat = 0,wherestraightforwardmethod. Data retrievalbegins soon tDCLK istheperiodofthedataclock.For example,ifafterDVALID goes low and finishesbeforeCONV tINT = 1000ms and DCLK = 10MHz, the maximumtoggles, as shown in Figure 20. For best number of DDC232s withFormat = 1 is shown inperformance,data retrievalmust stop tSDCV before Equation2:CONV toggles.Thismethod ismost appropriatefor longerintegrationtimes.The maximum timeavailable forreadbackistINT – tCMDR – tSDCV . (2) For DCLK = 10MHz and CLK = 5MHz, themaximum (or13 forFormat= 0)number of DDC232s that can be daisy-chained together(Format= 1)iscalculatedby Equation1: Figure20. Readback BeforeCONV Toggles Table15.Timing CharacteristicsforReadback SYMBOL DESCRIPTION MIN TYP MAX UNITS tSDCV Data RetrievalShutdown BeforeorAfterEdge ofCONV 10 ms

22 SubmitDocumentationFeedback Copyright© 2004–2010,Texas InstrumentsIncorporated

ProductFolderLink(s):DDC232

(20 /C003232)/C0116DCLK tINT tCMDR tSDCV tHDDODV tINT tINT … … … … … … Side A Data Side B Data Side A Data CONV DVALID DCLK DOUT DDC232 www.ti.com SBAS331D –AUGUST 2004–REVISED APRIL 2010 RETRIEVAL AFTER CONV TOGGLES (CONTINUOUS MODE) (3) For shorterintegrationtimes,more timeisavailableif NOTE: (16× 32)tDCLK isforFormat= 0.data retrievalbeginsafterCONV togglesand ends beforethe new data are ready.Data retrievalmust For DCLK = 10MHz, the maximum number of waittSDCV afterCONV togglesbeforebeginning.See DDC232s isfour(orfiveforFormat= 0). Figure21 foran example ofthis.The maximum time availableforretrievalis tCMDR – (tSDCV + tHDDODV ), regardlessoftINT.The maximum number ofDDC232s thatcan be daisy-chainedtogetherwithFormat = 1 is calculatedby Equation3: Figure21. Readback AfterCONV Toggles Copyright© 2004–2010,Texas InstrumentsIncorporated SubmitDocumentationFeedback 23 ProductFolderLink(s):DDC232

tINT /C0042/C0466tSDCV /C0041tSDCV /C0041tHDDODV /C0467 (20 /C003232)/C0116DCLK DCLK DVALID CONV DOUT Side B Data Side A Data tINT tSDCV tSDCV tHDDODV tINT tINT DDC232 SBAS331D –AUGUST 2004–REVISED APRIL 2010 www.ti.com RETRIEVAL BEFORE AND AFTER CONV TOGGLES (CONTINUOUS MODE) (4) For the absolutemaximum time fordata retrieval, NOTE: (16× 32)tDCLK isused forFormat= 0.datacan be retrievedbeforeand afterCONV toggles. Nearly allof tINT is availablefor data retrieval. For tINT = 400ms and DCLK = 10MHz, themaximum Figure22 illustrateshow thisisdone by combining number of DDC232s is five (or seven for thetwo previousmethods.Pause theretrievalduring Format= 0). CONV togglingtopreventdigitalnoise,as discussed previously,and finishbeforethenextdataareready. The maximum number of DDC232s that can be daisy-chainedtogetherwithFormat= 1 is: Figure22. Readback Beforeand AfterCONV Toggles

24 SubmitDocumentationFeedback Copyright© 2004–2010,Texas InstrumentsIncorporated

ProductFolderLink(s):DDC232

… … … … tINT tINT tNCDR 1 tINT tINT tNC DR2 Side A Data Side B Data CONV DVALID DCLK DOUT DDC232 www.ti.com SBAS331D –AUGUST 2004–REVISED APRIL 2010 RETRIEVAL: NONCONTINUOUS MODE untilthe second integrationcompletes,leavingless retrieval must be delayed Figure23. Readback inNoncontinuous Mode Copyright© 2004–2010,Texas InstrumentsIncorporated SubmitDocumentationFeedback 25 ProductFolderLink(s):DDC232

Power□Supplies RESET tPOR tRST CONV AVDD DVDD AGND DGND DDC232

10 F/c109

SBAS331D –AUGUST 2004–REVISED APRIL 2010 www.ti.com POWER-UP SEQUENCING LAYOUT Priorto power-up,alldigitaland analoginputsmust POWER SUPPLIES AND GROUNDINGbe low.At the timeof power-up,allof thesesignals should remain low untilthe power supplieshave Both AVDD and DVDD should be as quiet as stabilized,as shown inFigure24.At thistime,begin possible.Itisparticularlyimportanttoeliminatenoise supplyingthe master clocksignalto the CLK pin. fromAVDD thatisnonsynchronouswiththeDDC232 Wait fortime tPOR , then givea RESET pulse.After operation.Figure25 illustrateshow to supplypower releasingRESET, the configurationregistermust be to the DDC232. Each supplyof the DDC232 should programmed. Table 16 shows the timingfor the be bypassed with10mF solidtantalumcapacitors.Itis power-upsequence. recommended that both the analog and digital grounds(AGND and DGND) be connectedtoa single groundplaneon theprintedcircuitboard(PCB). Figure24. DDC232 Timing atPower-Up Figure25. Power-Supply Connections Table16.Timing CharacteristicsforDDC232 Power-Up Sequence ShieldingAnalog SignalPaths SYMBOL DESCRIPTION MIN TYP MAX UNITS As withany precisioncircuit,carefulPCB layoutwill WaitAfterPower-Up ensurethebestperformance.ItisessentialtomaketPOR 250 msUntilReset short,directinterconnectionsand avoidstraywiring tRST ResetLow Width 1 ms capacitance— particularlyattheanaloginputpinsand QGND. These analoginputpinsare high-impedance BLANKSPACE and extremelysensitiveto extraneousnoise.The QGND pin shouldbe treatedas a sensitiveanalogBLANKSPACE signaland connected directlyto the supplyground BLANKSPACE withpropershielding.Leakage currentsbetween the PCB tracescan exceed theinputbiascurrentoftheBLANKSPACE DDC232 if shieldingis not implemented.Digital signalsshouldbe kept as faras possiblefrom the analoginputsignalson thePCB.

26 SubmitDocumentationFeedback Copyright© 2004–2010,Texas InstrumentsIncorporated

ProductFolderLink(s):DDC232

www.ti.com SBAS331D –AUGUST 2004–REVISED APRIL 2010

REVISION HISTORY

NOTE: Page numbers forpreviousrevisionsmay differfrompage numbers inthecurrentversion. Changes from RevisionC (September 2006)toRevisionD Page Copyright© 2004–2010,Texas InstrumentsIncorporated SubmitDocumentationFeedback 27 ProductFolderLink(s):DDC232

www.ti.com 6-Feb-2026 PACKAGING INFORMATION Orderable part number Status (1) Material type (2) Package | Pins Package qty | Carrier RoHS (3) Lead finish/ Ball material (4) MSL rating/ Peak reflow (5) Op temp (°C) Part marking (6) 201-000795 Active Production NFBGA (ZXG) | 64 1000 | LARGE T&R Yes SNAGCU Level-3-260C-168 HR 0 to 70 DDC232 DDC232CKZXGR Active Production NFBGA (ZXG) | 64 1000 | LARGE T&R Yes SNAGCU Level-3-260C-168 HR 0 to 70 DDC232K DDC232CKZXGR.A Active Production NFBGA (ZXG) | 64 1000 | LARGE T&R Yes SNAGCU Level-3-260C-168 HR 0 to 70 DDC232K DDC232CKZXGT Active Production NFBGA (ZXG) | 64 250 | SMALL T&R Yes SNAGCU Level-3-260C-168 HR 0 to 70 DDC232K DDC232CKZXGT.A Active Production NFBGA (ZXG) | 64 250 | SMALL T&R Yes SNAGCU Level-3-260C-168 HR 0 to 70 DDC232K DDC232CZXGR Active Production NFBGA (ZXG) | 64 1000 | LARGE T&R Yes SNAGCU Level-3-260C-168 HR 0 to 70 DDC232 DDC232CZXGR.A Active Production NFBGA (ZXG) | 64 1000 | LARGE T&R Yes SNAGCU Level-3-260C-168 HR 0 to 70 DDC232 DDC232CZXGT Active Production NFBGA (ZXG) | 64 250 | SMALL T&R Yes SNAGCU Level-3-260C-168 HR 0 to 70 DDC232 DDC232CZXGT.A Active Production NFBGA (ZXG) | 64 250 | SMALL T&R Yes SNAGCU Level-3-260C-168 HR 0 to 70 DDC232 (1) Status: For more details on status, see our product life cycle. (2) Material type: When designated, preproduction parts are prototypes/experimental devices, and are not yet approved or released for full production. Testing and final process, including without limitation quality assurance, reliability performance testing, and/or process qualification, may not yet be complete, and this item is subject to further changes or possible discontinuation. If available for ordering, purchases will be subject to an additional waiver at checkout, and are intended for early internal evaluation purposes only. These items are sold without warranties of any kind. (3) RoHS values: Yes, No, RoHS Exempt. See the TI RoHS Statement for additional information and value definition. (4) Lead finish/Ball material: Parts may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two lines if the finish value exceeds the maximum column width. (5) MSL rating/Peak reflow: The moisture sensitivity level ratings and peak solder (reflow) temperatures. In the event that a part has multiple moisture sensitivity ratings, only the lowest level per JEDEC standards is shown. Refer to the shipping label for the actual reflow temperature that will be used to mount the part to the printed circuit board. (6) Part marking: There may be an additional marking, which relates to the logo, the lot trace code information, or the environmental category of the part. Multiple part markings will be inside parentheses. Only one part marking contained in parentheses and separated by a "~" will appear on a part. If a line is indented then it is a continuation of the previous line and the two combined represent the entire part marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative Addendum-Page 1

www.ti.com 6-Feb-2026 and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2

PACKAGE MATERIALS INFORMATION www.ti.com 5-Dec-2023 TAPE AND REEL INFORMATION Reel Width (W1) REEL DIMENSIONS A0B0K0WDimension designed to accommodate the component lengthDimension designed to accommodate the component thicknessOverall width of the carrier tapePitch between successive cavity centersDimension designed to accommodate the component width TAPE DIMENSIONSK0 P1B0WA0Cavity QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE Pocket QuadrantsSprocket HolesQ1Q1Q2Q2Q3Q3Q4Q4User Direction of Feed P1ReelDiameter *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Reel Diameter (mm) Reel Width W1 (mm) (mm) (mm) (mm) (mm) W (mm) Pin1 Quadrant Pack Materials-Page 1

PACKAGE MATERIALS INFORMATION www.ti.com 5-Dec-2023 TAPE AND REEL BOX DIMENSIONS Width (mm) W LH *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) DDC232CKZXGR NFBGA ZXG 64 1000 350.0 350.0 43.0 Pack Materials-Page 2

www.ti.com PACKAGE OUTLINE C 1.45 1.27 0.41

0.31 TYP

5.6 TYP

5.6 TYP

0.8 TYP

64X 0.51 0.41 A 8.1 7.9 B 8.1 7.9 (1.2) TYP (1.2) TYP NFBGA - 1.45 mm max heightZXG0064A PLASTIC BALL GRID ARRAY 4220377/A 03/2023 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. This package is lead-free. BALL A1 CORNER SEATING PLANE BALL TYP 0.12 C

0.15 C A B

0.08 C SYMM SYMM BALL A1 CORNER A 2 3 4 5 6 7 8 B C D E F G H SCALE 1.500

www.ti.com EXAMPLE BOARD LAYOUT 64X ( 0.4) (0.8) TYP (0.8) TYP ( 0.4) METAL

0.05 MAX

( 0.4) SOLDER MASK OPENING

0.05 MIN

NFBGA - 1.45 mm max heightZXG0064A PLASTIC BALL GRID ARRAY 4220377/A 03/2023 NOTES: (continued) 4. Final dimensions may vary due to manufacturing tolerance considerations and also routing constraints. For information, see Texas Instruments literature number SPRAA99 (www.ti.com/lit/spraa99). SYMM SYMM LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE:12X A 2 3 4 5 6 7 8 B C D E F G H NON-SOLDER MASK DEFINED (PREFERRED) SOLDER MASK DETAILS NOT TO SCALE EXPOSED METAL SOLDER MASK DEFINED EXPOSED METAL

www.ti.com EXAMPLE STENCIL DESIGN (0.8) TYP (0.8) TYP ( 0.4) TYP NFBGA - 1.45 mm max heightZXG0064A PLASTIC BALL GRID ARRAY 4220377/A 03/2023 NOTES: (continued) 5. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. SYMM SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE:12X SYMM A 2 3 4 5 6 7 8 B C D E F G H

IMPORTANT NOTICE AND DISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, regulatory or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you fully indemnify TI and its representatives against any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI’s products are provided subject to TI’s Terms of Sale, TI’s General Quality Guidelines, or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products. Unless TI explicitly designates a product as custom or customer-specified, TI products are standard, catalog, general purpose devices. TI objects to and rejects any additional or different terms you may propose. IMPORTANT NOTICE Copyright © 2026, Texas Instruments Incorporated Last updated 10/2025