Quad Current Input, 20-Bit Analog-To-Digital Converter datasheet (Rev. C)
Document overview
- Manufacturer or author: Texas Instruments, Incorporated [SBAS255,C]
- PDF pages: 36
Technical content
FEATURES
/C0068SINGLE-CHIP SOLUTION TO DIRECTLY MEASURE FOUR LOW-LEVEL CURRENTS /C0068HIGH PRECISION, TRUE INTEGRATING FUNCTION /C0068INTEGRAL LINEARITY: ±0.01% of Reading ±0.5ppm of FSR /C0068VERY LOW NOISE: 5.2ppm of FSR /C0068LOW POWER: 13.5mW/channel /C0068ADJUSTABLE DATA RATE: Up to 3.125kSPS /C0068PROGRAMMABLE FULL SCALE /C0068DAISY-CHAINABLE SERIAL INTERFACE
APPLICATIONS
/C0068CT SCANNER DAS /C0068PHOTODIODE SENSORS /C0068INFRARED PYROMETERS /C0068LIQUID/GAS CHROMATOGRAPHY Protected by US Patent #5841310 Dual Switched Integrator Dual Switched Integrator Modulator Digital Filter Digital Input/Output FORMAT DCLK DCLK DVALID DOUT DOUT DIN DIN Control IN3 IN1 VREF DVDDAVDD DGNDAGND Dual Switched Integrator Dual Switched Integrator Modulator Digital Filter IN4 IN2 CLK CONV RANGE0 RANGE1 RANGE2 TEST CLK_4X HISPD/LOPWR RESET
DESCRIPTION
The DDC114 is a 20-bit, quad channel, current-input analog-to-digital (A/D) converter. It combines both current-to-voltage and A/D conversion so that four low-level current output devices, such as photodiodes, can be directly connected to its inputs and digitized. For each of the four inputs, the DDC114 provides a dual-switched integrator front-end. This design allows for continuous current integration: while one integrator is being digitized by the onboard A/D converter, the other is integrating the input current. Adjustable full-scale ranges from 12pC to 350pC and adjustable integration times from 50µs to 1s allow currents from fAs to µAs to be measured with outstanding precision. Low-level linearity is ±0.5ppm of the full-scale range and noise is 5.2ppm of the full-scale range. Two modes of operation are provided. In Low-Power mode, total power dissipation is only 13.5mW per channel with a maximum data rate of 2.5kSPS. High-Speed mode supports data rates up to 3.125kSPS with a corresponding dissipation of 18mW per channel. The DDC114 has a serial interface designed for daisy-chaining in multi-device systems. Simply connect the output of one device to the input of the next to create the chain. Common clocking feeds all the devices in the chain so that the digital overhead in a multi-DDC114 system is minimal. The DDC114 is a single-supply device using a +5V analog supply and supporting a +2.7V to +5.25V digital supply. Operating over the industrial temperature range of −40°C to +85°C, the DDC114 is offered in a QFN-48 package. DDC114 SBAS255C − JUNE 2004 − REVISED APRIL 2009 Quad Current Input, 20-Bit Analog-To-Digital Converter www.ti.com Copyright 2004−2009, Texas Instruments Incorporated Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. /C0080/C0082/C0079/C0068/C0085/C0067/C0084/C0073/C0079/C0078 /C0068/C0065/C0084/C0065 /C0105/C0110/C0102/C0111/C0114/C0109/C0097/C0116/C0105/C0111/C0110 /C0105/C0115 /C0099/C0117/C0114/C0114/C0101/C0110/C0116 /C0097/C0115 /C0111/C0102 /C0112/C0117/C0098/C0108/C0105/C0099/C0097/C0116/C0105/C0111/C0110 /C0100/C0097/C0116/C0101/C0046 /C0080/C0114/C0111/C0100/C0117/C0099/C0116/C0115 /C0099/C0111/C0110/C0102/C0111/C0114/C0109 /C0116/C0111 /C0115/C0112/C0101/C0099/C0105/C0102/C0105/C0099/C0097/C0116/C0105/C0111/C0110/C0115 /C0112/C0101/C0114 /C0116/C0104/C0101 /C0116/C0101/C0114/C0109/C0115 /C0111/C0102 /C0084/C0101/C0120/C0097/C0115 /C0073/C0110/C0115/C0116/C0114/C0117/C0109/C0101/C0110/C0116/C0115 /C0115/C0116/C0097/C0110/C0100/C0097/C0114/C0100 /C0119/C0097/C0114/C0114/C0097/C0110/C0116/C0121/C0046 /C0080/C0114/C0111/C0100/C0117/C0099/C0116/C0105/C0111/C0110 /C0112/C0114/C0111/C0099/C0101/C0115/C0115/C0105/C0110/C0103 /C0100/C0111/C0101/C0115 /C0110/C0111/C0116 /C0110/C0101/C0099/C0101/C0115/C0115/C0097/C0114/C0105/C0108/C0121 /C0105/C0110/C0099/C0108/C0117/C0100/C0101 /C0116/C0101/C0115/C0116/C0105/C0110/C0103 /C0111/C0102 /C0097/C0108/C0108 /C0112/C0097/C0114/C0097/C0109/C0101/C0116/C0101/C0114/C0115/C0046
/C0068/C0068/C0067/C0049/C0049/C0052 SBAS255C − JUNE 2004 − REVISED APRIL 2009 www.ti.com PACKAGE/ORDERING INFORMATION For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. ABSOLUTE MAXIMUM RATINGS (1) (1)Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not implied. This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
/C0068/C0068/C0067/C0049/C0049/C0052 SBAS255C − JUNE 2004 − REVISED APRIL 2009 www.ti.com
ELECTRICAL CHARACTERISTICS
At TA = +25°C, AVDD = +5V, DVDD = 3V, VREF = +4.096V, Range 5 (250pC), and continuous mode operation, unless otherwise noted. Low-Power Mode: TINT = 400µs and CLK = 4MHz; High-Speed Mode: TINT = 320µs and CLK = 4.8MHz. Low-Power Mode High-Speed Mode PARAMETER TEST CONDITIONS MIN TYP MAX MIN TYP MAX UNITS ANALOG INPUT RANGE Range 0 10.2 12 13.8 ∗(1) ∗ ∗ pC Range 1 47.5 50 52.5 ∗ ∗ ∗ pC Range 2 95 100 105 ∗ ∗ ∗ pC Range 3 142.5 150 157.5 ∗ ∗ ∗ pC Range 4 190 200 210 ∗ ∗ ∗ pC Range 5 237.5 250 262.5 ∗ ∗ ∗ pC Range 6 285 300 315 ∗ ∗ ∗ pC Range 7 332.5 350 367.5 ∗ ∗ ∗ pC Negative Full-Scale Range −0.4% of Positive Full-Scale Range ∗ pC Input Current(2) 750 ∗ µA DYNAMIC CHARACTERISTICS Data Rate 2.5 3.125 kSPS Integration Time, TINT Continuous Mode 400 1,000,000 320 ∗ µS Integration Time, TINT Non-continuous Mode, Range 1 to 7 50 ∗ µS System Clock Input (CLK) CLK_4X = 0 4 4.8 MHz CLK_4X = 1 16 19.2 MHz Data Clock (DCLK) 16 ∗ MHz ACCURACY Noise, Low-Level Input(3) C SENSOR (4) = 50pF, Range 5 (250pC) 5.2 6.5 5.5 7 ppm of FSR (5), rms Integral Linearity Error(6) ±0.01% Reading ± 0.5ppm FSR, typ ∗ Integral Linearity Error(6) ±0.025% Reading ± 1.0ppm FSR, max ∗ Resolution FORMA T = 1 20 ∗ BitsResolution FORMA T = 0 16 ∗ Bits Input Bias Current 0.1 10 ∗ ∗ pA Range Error Match(7) All Ranges 0.1 0.5 ∗ ∗ % of FSR Range Sensitivity to VREF VREF = 4.096 ± 0.1V 1:1 ∗ Offset Error ±400 ±1000 ∗ ∗ ppm of FSR Offset Error Match(7) ±100 ∗ ppm of FSR DC Bias Voltage(9) Low-Level Input (< 1% FSR) ±0.05 ±2 ∗ ∗ mV Power-Supply Rejection Ratio at dc ±25 ±200 ∗ ∗ ppm of FSR/V Internal Test Signal 11 ∗ pC Internal Test Accuracy ±10 ∗ % PERFORMANCE OVER TEMPERA TURE Offset Drift ±0.5 ±3(8) ∗ ∗ ppm of FSR/°C Offset Drift Stability ±0.2 ±1(8) ∗ ∗ ppm of FSR/ minute DC Bias Voltage Drift(9) 3 ∗ µV/°C Input Bias Current Drift TA = +25°C to +45°C 0.01 1(8) ∗ ∗ pA/°C Range Drift(10) 25 ∗ ppm/°C REFERENCE Voltage 4.000 4.096 4.200 ∗ ∗ ∗ V Input Current(11) Average Value 75 95 µA (1)∗ indicates that specification is the same as Low-Power Mode. (2)Exceeding maximum input current specification may damage device. (3)Input is less than 1% of full scale. (4)C SENSOR is the capacitance seen at the DDC114 inputs from wiring, photodiode, etc. (5)FSR is Full-Scale Range. (6)A best-fit line is used in measuring nonlinearity. (7)Matching between side A and side B of the same input. (8)Ensured by design, not production tested. (9)Voltage produced by the DDC114 at its input which is applied to the sensor. (10)Range drift does not include external reference drift. (11)Input reference current decreases with increasing TINT (see the Voltage Reference section, page 11).
/C0068/C0068/C0067/C0049/C0049/C0052 SBAS255C − JUNE 2004 − REVISED APRIL 2009 www.ti.com ELECTRICAL CHARACTERISTICS (continued) At TA = +25°C, AVDD = +5V, DVDD = 3V, VREF = +4.096V, Range 5 (250pC), and continuous mode operation, unless otherwise noted. Low-Power Mode: TINT = 400µs and CLK = 4MHz; High-Speed Mode: TINT = 320µs and CLK = 4.8MHz. High-Speed ModeLow-Power Mode PARAMETER UNITSMAXTYPMINMAXTYPMINTEST CONDITIONS DIGITAL INPUT/OUTPUT Logic Levels VIH 0.8DVDD DVDD + 0.1 ∗ ∗ V VIL − 0.1 0.2DVDD ∗ ∗ V VOH IOH = −500µA DVDD − 0.4 V VOL IOL = 500µA 0.4 ∗ V Input Current (IIN) 0 < VIN < DVDD ±10 ∗ µA Data Format(12) Straight Binary ∗ POWER-SUPPL Y REQUIREMENTS Analog Power-Supply Voltage (AVDD) 4.75 5.25 ∗ ∗ V Digital Power-Supply Voltage (DVDD) 2.7 5.25 ∗ ∗ V Supply Current Total Analog Current 10.5 14.0 mA Total Digital Current DVDD = +3V 0.5 0.67 mA Total Power Dissipation DVDD = +3V 54 75 72 100 mW Total Power Dissipation per Channel DVDD = +3V 13.5 18.75 18 25 mW (12)Data format is Straight Binary with a small offset. The number of bits in the output word is controlled by the FORMAT pin (see text).
/C0068/C0068/C0067/C0049/C0049/C0052 SBAS255C − JUNE 2004 − REVISED APRIL 2009 www.ti.com PIN CONFIGURATIONS Top View QFN DIN DIN NC NC RESET TEST DGND DGND AGND AVDD AGND AGND DGND DGND CONV DGND DVALID DGND CLK DGND DCLK DCLK DGND DVDD AGND AGND AIN4 AGND AIN3 AGND AGND AGND AIN2 AGND AIN1 AGND DOUT DOUT CLK_4X FORMAT HISPD/LOPWR RANGE0 RANGE1 RANGE2 AGND VREF AGND AGND 48 47 46 45 44 43 42 41 40 39 38 13 14 15 16 17 18 19 20 21 22 23 DDC114 PIN DESCRIPTIONS PIN NUMBER FUNCTION DESCRIPTION DOUT 1 Digital Output Serial Data Output DOUT 2 Digital Output Serial Data Output: Complementary Signal CLK_4X 3 Digital Input Master Clock Divider Control: 0 = divide by 1, 1 = divide by 4 FORMAT 4 Digital Input Digital Output Word Format: 0 = 16 Bits, 1 = 20 Bits HISPD/LOPWR 5 Digital Input Mode Control: 0 = Low-Power, 1 = High-Speed RANGE0 6 Digital Input Range Control 0 (least significant bit) RANGE1 7 Digital Input Range Control 1 RANGE2 8 Digital Input Range Control 2 (most significant bit) AGND 9, 11-14, 16, 18-20, 22, 24-26, 28 Analog Analog Ground VREF 10 Analog Input External Voltage Reference Input, 4.096V Nominal AIN4 15 Analog Input Analog Input 4 AIN3 17 Analog Input Analog Input 3 AIN2 21 Analog Input Analog Input 2 AIN1 23 Analog Input Analog Input 1 AVDD 27 Analog Analog Power Supply, 5V Nominal DGND 29, 30, 38, 41, 43, 45, 47, 48 Digital Digital Ground TEST 31 Digital Input Test Mode Control RESET 32 Digital Input Resets the Digital Circuitry, Active Low NC 33, 34 — No Connection DIN 35 Digital Input Serial Data Input: Complementary Signal (optional, see text on page 13) DIN 36 Digital Input Serial Data Input DVDD 37 Digital Digital Power Supply, 3V Nominal DCLK 39 Digital Input Serial Data Clock Input: Complementary Signal (optional, see text on page 13) DCLK 40 Digital Input Serial Data Clock Input CLK 42 Digital Input Master Clock Input DVALID 44 Digital Output Data Valid Output, Active Low CONV 46 Digital Input Conversion Control Input: 0 = Integrate on Side B, 1 = Integrate on Side A
/C0068/C0068/C0067/C0049/C0049/C0052 SBAS255C − JUNE 2004 − REVISED APRIL 2009 www.ti.com TYPICAL CHARACTERISTICS At TA = +25°C, characterization done with Range 5 (250pC), AVDD = +5V, DVDD = 3V, VREF = +4.096V, Low Power Mode: TINT = 400µs and CLK = 4MHz, unless otherwise noted. NOISE vs CSENSOR 100 40005 0 0 300200 C SENSOR (pF) N o i s e( p p mo fF S R ,r m s ) Range 1 Range 2 Range 7 NOISE vs TINT 1 10000.1 100 10 TINT (µs) Noise (ppm of FSR, rms) C SENSOR = 50pF C SENSOR =0 p F Range 5 NOISE vs TEMPERATURE −40 −15 10 35 60 85 Temperature (/C0095C) Noise (ppm of FSR, rms) C SENSOR =5 0 p F Range 1 Range 3Range 2 Range 7 NOISE vs CSENSOR Noise (ppm of FSR, rms) C SENSOR (pF) 100 150 200 300 500 Range 23.6 30.8 36.3 41.3 46.1 57.0 68.1 89.3 134.0 Range 7.3 10.4 12.3 14.4 16.0 18.8 21.7 27.7 38.9 Range 5.2 6.7 8.2 8.9 10.0 11.9 13.5 16.3 22.4 Range 4.4 5.5 6.5 7.2 8.0 9.2 10.2 12.5 16.6 Range 4.2 4.9 5.6 6.0 6.7 7.8 8.6 10.6 13.5 Range 4.0 4.5 5.1 5.4 5.9 6.8 7.6 9.0 11.7 Range 3.8 4.3 4.8 5.1 5.4 6.1 6.8 8.1 10.4 Range 3.7 4.1 4.4 4.7 5.0 5.7 6.4 7.4 9.5 NOISE vs INPUT LEVEL 20 3010 800 100 60 70 9040 50 Input Level (% of Full−Scale) Noise (ppm of FSR, rms) C SENSOR = 50pF C SENSOR = 0pF Range 5 RANGE DRIFT vs TEMPERATURE −40 −15 10 35 60 85 Temperature (/C0095C) Range Drift (ppm) 2000 1500 1000 500 −500 −1000 −1500 −2000 All Ranges
/C0068/C0068/C0067/C0049/C0049/C0052 SBAS255C − JUNE 2004 − REVISED APRIL 2009 www.ti.com TYPICAL CHARACTERISTICS (continued) At TA = +25°C, characterization done with Range 5 (250pC), AVDD = +5V, DVDD = 3V, VREF = +4.096V, Low Power Mode: TINT = 400µs and CLK = 4MHz, unless otherwise noted. IB vs TEMPERATURE 25 35 45 55 65 75 85 Temperature (/C0095C) IB (pA) 0.1 0.01 All Ranges ANALOG SUPPLY CURRENT vs TEMPERATURE −40 −15 10 35 60 85 Temperature (/C0095C)Temperature (/C0095C) Current (mA) Low−Power Mode POWER CONSUMPTION HISTOGRAM 12.00 12.25 12.50 12.75 13.00 13.25 13.50 13.75 14.00 14.25 14.50 14.75 15.00 15.25 15.50 15.75 16.00 Power per Channel (mW) Occurences (%) Low−Power ModeData collected from multiple lots. OFFSET DRIFT vs TEMPERATURE 25 35 45 55 65 75 85 Temperature (/C0095C) Offset Drift (ppm of FSR) 100 −50 −100 DIGITAL SUPPLY CURRENT vs TEMPERATURE 1.2 1.0 0.8 0.6 0.4 0.2 −40 −15 10 35 60 85 Temperature (/C0095C) Current (mA) DVDD = 3V DVDD = 5V Low Power− Mode OFFSET DRIFT OVER TIME HISTOGRAM 600 500 400 300 200 100 Offset Drift (ppm of FSR/minute) Occurences Range 5Repeated measurement of offset drift over a one minute interval.
cases where a large number of converters are needed. shifted out or while CONV is transitioning. Table 3. CLK_4X Pin Operation sponding typical power of 18.0mW/channel. Table 4. HISPD/LOPWR Pin Operation 7 or t8 to insure data is valid. Figure 9. Reset Timing INT to be adjusted in steps of 62.5ns.
integrated by one of the two sides of each input. Table 5. State Descriptions
1 Ncont Complete m/r/az of side A, then side B (if previous
2 Ncont Prepare side A for integration. 4 Cont Integrate on side B; m/r/az on side A. 5 Cont Integrate on side A; m/r/az on side B. 7 Ncont Prepare side B for integration.
8 Ncont Complete m/r/az of side B, then side A (if previous
6 CONV
Figure 10. Integrate/Measure State Diagram During cont mode, mbsy is not active when CONV toggles. integrating when the other side finishes its integration. and 6, only perform an integration (no m/r/az cycle). the integrations always alternate between sides A and B. relationship during ncont mode. state is either 1 or 8, depending on the initial level of CONV. For CONV held high at power-up, the beginning state is 1.
Figure 12. Timing Diagram of the Internal Operation in Continuous Mode of the DDC114 Table 7. Timing for the Internal Operation in Continuous Mode
integrations are being measured, reset and auto-zeroed.
- When the m/r/az cycles are completed, time
of ncont mode is slightly different from that of cont mode. Figure 13. Non-Continuous Mode Timing
0.4% of the positive full−scale. Table 9. Ideal Output Code(1) vs Input Signal (1)Excludes the effects of noise, INL, offset, and gain errors. data while CONV changes as this can introduce noise. multichannel systems requiring only 16 bits of resolution. Figure 20. Digital Interface Timing Diagram for Data Retrieval From a Single DDC114 Table 10. Timing for the DDC114 Data Retrieval (1)With a maximum load of one DDC114 (4pF typical) with an additional load of 5pF.
NOTE: 64τDCLK is used for FORMAT = low. Figure 23. Readback Before CONV Toggles
NOTE: 64τDCLK is used for FORMAT = low. 41 (or 52 for FORMAT = low). Figure 24. Readback After CONV Toggles
SBAS255C − JUNE 2004 − REVISED APRIL 2009 www.ti.com
Revision History
DATE REV PAGE SECTION DESCRIPTION 4/09 C 1 Front Page Updated front page appearance. 4/09 C 9 Theory of Operation Changed last sentence of first paragraph on page 9. NOTE : Page numbers for previous revisions may differ from page numbers in the current version.
www.ti.com 11-Nov-2025 PACKAGING INFORMATION Orderable part number Status (1) Material type (2) Package | Pins Package qty | Carrier RoHS (3) Lead finish/ Ball material (4) MSL rating/ Peak reflow (5) Op temp (°C) Part marking (6) DDC114IRTCR Active Production VQFN (RTC) | 48 2500 | LARGE T&R Yes SN Level-3-260C-168 HR -40 to 85 DDC114 DDC114IRTCR.B Active Production VQFN (RTC) | 48 2500 | LARGE T&R Yes SN Level-3-260C-168 HR -40 to 85 DDC114 DDC114IRTCT Active Production VQFN (RTC) | 48 250 | SMALL T&R Yes SN Level-3-260C-168 HR -40 to 85 DDC114 DDC114IRTCT.B Active Production VQFN (RTC) | 48 250 | SMALL T&R Yes SN Level-3-260C-168 HR -40 to 85 DDC114 (1) Status: For more details on status, see our product life cycle. (2) Material type: When designated, preproduction parts are prototypes/experimental devices, and are not yet approved or released for full production. Testing and final process, including without limitation quality assurance, reliability performance testing, and/or process qualification, may not yet be complete, and this item is subject to further changes or possible discontinuation. If available for ordering, purchases will be subject to an additional waiver at checkout, and are intended for early internal evaluation purposes only. These items are sold without warranties of any kind. (3) RoHS values: Yes, No, RoHS Exempt. See the TI RoHS Statement for additional information and value definition. (4) Lead finish/Ball material: Parts may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two lines if the finish value exceeds the maximum column width. (5) MSL rating/Peak reflow: The moisture sensitivity level ratings and peak solder (reflow) temperatures. In the event that a part has multiple moisture sensitivity ratings, only the lowest level per JEDEC standards is shown. Refer to the shipping label for the actual reflow temperature that will be used to mount the part to the printed circuit board. (6) Part marking: There may be an additional marking, which relates to the logo, the lot trace code information, or the environmental category of the part. Multiple part markings will be inside parentheses. Only one part marking contained in parentheses and separated by a "~" will appear on a part. If a line is indented then it is a continuation of the previous line and the two combined represent the entire part marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1
PACKAGE MATERIALS INFORMATION www.ti.com 5-Dec-2023 TAPE AND REEL INFORMATION Reel Width (W1) REEL DIMENSIONS A0B0K0WDimension designed to accommodate the component lengthDimension designed to accommodate the component thicknessOverall width of the carrier tapePitch between successive cavity centersDimension designed to accommodate the component width TAPE DIMENSIONSK0 P1B0WA0Cavity QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE Pocket QuadrantsSprocket HolesQ1Q1Q2Q2Q3Q3Q4Q4User Direction of Feed P1ReelDiameter *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Reel Diameter (mm) Reel Width W1 (mm) (mm) (mm) (mm) (mm) W (mm) Pin1 Quadrant Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION www.ti.com 5-Dec-2023 TAPE AND REEL BOX DIMENSIONS Width (mm) W LH *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) DDC114IRTCR VQFN RTC 48 2500 350.0 350.0 43.0 Pack Materials-Page 2
www.ti.com GENERIC PACKAGE VIEW Images above are just a representation of the package family, actual package may vary. Refer to the product data sheet for package details. VQFNP - 0.9 mm max heightRTC 48 PLASTIC QUAD FLATPACK - NO LEAD7 x 7, 0.5 mm pitch 4224601/A
RTC (S-PVQFN-N48) PLASTIC QUAD FLATPACK NO-LEAD 6,90 6,85 ___ ., 6,65 B -----. _L1__Q_ Pin 1 Identifier c::;; r r . . 0,90 Max / \\ 0, 2 0 ting p I an e 0, 70 0,05 Max. 0,00 SIZE 61j2_ SHAPE SHOWN ON SPARATE SHEET L 0,60T 4X O 24 0,50 48X 0,30 NOTES: A. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.SM-1994. B. This drawing is subject to change without notice. C. QFN (Quad Flotpack No-Lead) Package configuration. D. The pockoge thermal pad must be soldered to the board for thermal and mechanical performance. 4205143/D 05/11 E. See the additional figure in the Product Data Sheet for details regarding the exposed thermal pad features and dimensions. ,t;TEXAS INSTRUMENTS www.ti.com
RTC (S-PVQFN-N48) PLASTIC QUAD FLATPACK NO-LEAD Note D Example Board Layout !OOOOOOOOOOOD CJ I I le,_; 1 5,10 C) -+ CJ617 8C) CJ ' ' Example Stencil Design
0.125 Thick Stencil
(Note E) 0,25 C) CJ I I I I C) --- CJ □-9□ .DD DD I 7,8 i i i i i Non Solder Mask Defined Pad Example Solder Mask Opening 0,08 R0,14 (Note F) (63% Printed Solder Coverage by Area) 25x00,3 Example Via Layout Design Via layout may vary depending on layout constraints (Note D, F) 20x1 ,0 0 0 0 0 I I \\ 0,07 JI I I Pad Geometry (Note C) 0 0 0 0 '\\'.'II Around I NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. C. Publication IPC-7351 is recommended for alternate designs. 4210029-2/D 05/11 D. This package is designed to be soldered to a thermal pad on the board. Refer to Application Note, Quad Flat-Pack for specific thermal information, via requirements, and recommended board layout. These documents are available at E. Laser cutting apertures with trapezoidal walls and also rounding corners will offer better paste release. Customers should contact their board assembly site for stencil design recommendations. Refer to IPC 7525 for stencil design considerations. F. Customers should contact their board fabrication site for recommended solder mask tolerances and via tenting recommendations for vias placed in the thermal pad. ,t;TEXAS INSTRUMENTS www.ti.com
IMPORTANT NOTICE AND DISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, regulatory or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you fully indemnify TI and its representatives against any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI’s products are provided subject to TI’s Terms of Sale, TI’s General Quality Guidelines, or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products. Unless TI explicitly designates a product as custom or customer-specified, TI products are standard, catalog, general purpose devices. TI objects to and rejects any additional or different terms you may propose. IMPORTANT NOTICE Copyright © 2025, Texas Instruments Incorporated Last updated 10/2025