DAC7800, 7801, 7802: Dual Monolithic CMOS 12-Bit Multiplying D/A Converter datasheet (Rev. B)

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 25

Technical content

DESCRIPTION

The DAC7800, DAC7801 and DAC7802 are members of a new family of monolithic dual 12-bit CMOS multiplying Digi- tal-to-Analog Converters (DACs). The digital interface speed and the AC multiplying performance are achieved by using an advanced CMOS process optimized for data conversion circuits. High stability on-chip resistors provide true 12-bit integral and differential linearity over the wide industrial temperature range of –40°C to +85°C. The DAC7800 features a serial interface capable of clocking- in data at a rate of at least 10MHz. Serial data is clocked (edge triggered) MSB first into a 24-bit shift register and then latched into each DAC separately or simultaneously as required by the application. An asynchronous CLEAR control is provided for power-on reset or system calibration func- tions. It is packaged in a 16-pin 0.3" wide plastic DIP. The DAC7801 has a 2-byte (8 + 4) double-buffered interface. Data is first loaded (level transferred) into the input registers in two steps for each DAC. Then both DACs are updated simultaneously. The DAC7801 features an asynchronous CLEAR control. The DAC7801 is packaged in a 24-pin 0.3" wide plastic DIP. The DAC7802 has a single-buffered 12-bit data word interface. Parallel data is loaded (edge triggered) into the single DAC register for each DAC. The DAC7802 is packaged in a 24-pin 0.3" wide plastic DIP.

FEATURES

G TWO DACs IN A 0.3" WIDE PACKAGE G SINGLE +5V SUPPLY G HIGH-SPEED DIGITAL INTERFACE: Serial—DAC7800 8 + 4-Bit Parallel—DAC7801 12-Bit Parallel—DAC7802 G MONOTONIC OVER TEMPERATURE G LOW CROSSTALK: –94dB min G FULLY SPECIFIED OVER –40 O C TO +85O C

APPLICATIONS

G ATE PIN ELECTRONICS LEVEL SETTING G PROGRAMMABLE FILTERS G PROGRAMMABLE GAIN CIRCUITS G AUTO-CALIBRATION CIRCUITS Dual Monolithic CMOS 12-Bit Multiplying DIGITAL-TO-ANALOG CONVERTERS Serial Interface 8-Bit Interface

8 Bits + 4 Bits

R 12-Bit Interface DAC7802 CSA WR CSB

12 AGND B

R AGND A REF AV DAC7800 DAC7801 DAC7802 SBAS005B – JANUARY 1990 – REVISED FEBRUARY 2004 www.ti.com PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 1990-2004, Texas Instruments Incorporated Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners.

DAC7800, 7801, 78022 SBAS005Awww.ti.com SPECIFIED RELATIVE GAIN PACKAGE TEMPERATURE PACKAGE ORDERING TRANSPORT PRODUCT ACCURACY ERROR PACKAGE-LEAD DESIGNATOR (1) RANGE MARKING NUMBER MEDIA, QUANTITY DAC7800KP ±1LSB ±3LSB DIP-16 N –40°C to +85°C DAC7800KP DAC7800KP Rails, 25 DAC7800LP ±1/2 LSB ±1LSB DIP-16 N DAC7800LP DAC7800LP Rails, 25 DAC7800KU —— SO-16 DW –40°C to +85°C DAC7800KU DAC7800KU/1K Tape and Reel, 1000 DAC7800LU —— SO-16 DW DAC7800LU DAC7800LU/1K Tape and Reel, 1000 DAC7801KP ±1LSB ±3LSB DIP-24 NTG –40°C to +85°C DAC7801KP DAC7801KP Rails, 15 DAC7801LP ±1/2 LSB ±1LSB DIP-24 NTG DAC7801LP DAC7801LP Rails, 15 DAC7801KU —— SO-24 DW –40°C to +85°C DAC7801KU DAC7801KU/1K Tape and Reel, 1000 DAC7801LU —— SO-24 DW DAC7801LU DAC7801LU/1K Tape and Reel, 1000 DAC7802KP ±1LSB ±3LSB DIP-24 NTG –40°C to +85°C DAC7802KP DAC7802KP Rails, 15 DAC7802LP ±1/2 LSB ±1LSB DIP-24 NTG DAC7802LP DAC7802LP Rails, 15 DAC7802KU —— SO-24 DW –40°C to +85°C DAC7802KU DAC7802KU/1K Tape and Reel, 1000 DAC7802LU —— SO-24 DW DAC7802LU DAC7802LU/1K Tape and Reel, 1000 NOTE: (1 ) For the most current specifications and package information, see the package option addendum located at the end of this data sheet.

ELECTRICAL CHARACTERISTICS

At VDD = +5VDC, VREF A = VREF B = +10V, TA = –40°C to +85°C, unless otherwise noted. DAC7800, 7801, 7802K DAC7800, 7801, 7802L PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS ACCURACY Resolution 12 ✻ Bits Relative Accuracy ±1 ±1/2 LSB Differential Nonlinearity ±1 ✻ LSB Gain Error Measured Using R FB A and RFB B. ±3 ±1 LSB All Registers Loaded with All 1s. Gain Temperature Coefficient(1) 25 ✻✻ ppm/°C Output Leakage Current T A = +25°C 0.005 10 ✻✻ nA TA = –40°C to +85°C 3 150 ✻✻ nA REFERENCE INPUT Input Resistance 6 10 14 ✻✻✻ kΩ Input Resistance Match 0.5 3 ✻ 2% DIGITAL INPUTS VIH (Input HIGH Voltage) 2 ✻ V VIL (Input LOW Voltage) 0.8 ✻ V IIN (Input Current) T A = +25°C ±1 ✻ µA TA = –40°C to +85°C ±10 ✻ µA C IN (Input Capacitance) 0.8 10 ✻✻ pF POWER SUPPLY VDD 4.5 5.5 ✻✻ V IDD 0.2 2 ✻✻ mA Power-Supply Rejection V DD from 4.5V to 5.5V 0.002 ✻ %/% ✻ Same specification as for DAC7800, 7801, 7802K. NOTE: (1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. Exposure to absolute maximum conditions for extended periods may affect device reliaiblity. ABSOLUTE MAXIMUM RATINGS (1) At TA = +25°C, unless otherwise noted. ELECTROSTATIC DISCHARGE SENSITIVITY This integrated circuit can be damaged by ESD. Texas Instru- ments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION

DAC7800, 7801, 7802 3 SBAS005A www.ti.com AC PERFORMANCE OUTPUT OP AMP IS OPA602. At VDD = +5VDC, VREF A = VREF B = +10V, TA = +25°C, unless otherwise noted. These specifications are fully characterized but not subject to test. NOTE: (1) Ensured but not tested. DAC7800, 7801, 7802K DAC7800, 7801, 7802L PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS OUTPUT CURRENT SETTLING TIME To 0.01% of Full-Scale 0.4 0.8 ✻✻ µs R L = 100Ω , CL = 13pF DIGITAL-TO-ANALOG GLITCH IMPULSE VREF A = VREF B = 0V 0.9 ✻ nV-s R L = 100Ω , CL = 13pF AC FEEDTHROUGH fVREF = 10kHz –75 –72 ✻✻ dB OUTPUT CAPACITANCE DAC Loaded with All 0s 30 50 ✻✻ pF DAC Loaded with All 1s 70 100 ✻✻ pF CHANNEL-TO-CHANNEL ISOLATION VREF A to IOUT B fVREF A = 10kHz –90 –94 ✻✻ dB VREF B = 0V, Both DACs Loaded with 1s VREF B to IOUT A fVREF B = 10kHz –90 –101 ✻✻ dB VREF A = 0V, Both DACs Loaded with 1s DIGITAL CROSSTALK Full-Scale Transition 0.9 ✻ nV-s R L = 100Ω , CL = 13pF ✻ Same specification as for DAC7800, 7801, and 7802K. DAC7800 BLOCK DIAGRAM DAC A DAC B DAC A Register UPD B I AGND B R V V R I AGND A UPD A OUT B FB B REF B REF A FB A OUT A VDD DGND DAC B Register Bit 0 Bit 11 Bit 12 Bit 23 Control Logic and Shift Register 7 11 CLR DAC7800 Data In CLK CS PIN CONFIGURATION AGND A CLK UPD A Data In CS AGND B I R V V CLR UPD B DGND OUT A FB A REF A OUT B DAC7800 I R V FB B REF B DD CLK UPD A UPD B CS CLR FUNCTION XXXX0 A l l register contents set to 0’s (asynchronous). X X X 1 X No data transfer. X X 0 1 Input data is clocked into input register (location Bit 23) and previous data shifts. X0101 Input register bits 23 (LSB) - 12 (MSB) are loaded into DAC A. X1001 Input register bits 11 (LSB) - 0 (MSB) are loaded into DAC B. X0001 Input register bits 23 (LSB) - 12 (MSB) are loaded into DAC A, and input register bits 11 (LSB) - 0 (MSB) are loaded into DAC B. X = Don’t care. means falling edge triggered. LOGIC TRUTH TABLE Top View DIP

DAC7800, 7801, 78024 SBAS005Awww.ti.com DATA CS CLK UPD A UPD B CLR t8 t4 NOTES: (1) All input signal rise and fall times are measured from 10% to 90% of +5V. t = t = 5ns. (2) Timing measurement reference level isV + V FR IH IL . PARAMETER MINIMUM t1 — Data Setup Time 15ns t2 — Data Hold Time 15ns t3 — Chip Select to CLK, 15ns Update, Data Setup Time t4 — Chip Select to CLK, 40ns Update, Data Hold Time t5 — CLK Pulse Width 40ns t6 — Clear Pulse Width 40ns t7 — Update Pulse Width 40ns t8 — CLK Edge to UPD A 15ns or UPD B TIMING CHARACTERISTICS VDD = +5V, VREF A = VREF B = +10V, TA = –40°C to +85°C. Data In Bit 0 Bit 23Bit 22Bit 21Bit 20Bit 19Bit 18Bit 17Bit 16Bit 15Bit 14Bit 13Bit 12Bit 11Bit 10Bit 9Bit 8Bit 7Bit 6Bit 5Bit 4Bit 3Bit 2Bit 1 LSB DAC A MSB DAC A LSB DAC B MSB DAC B DAC7800 Data Input Sequence DAC7800 Digital Interface Block Diagram 24-Bit Shift Register DAC A Register UPD A Data In CLK UPD B LSB MSB DAC B Register LSB MSB Bit Bit Bit Bit CLK DATA INPUT FORMAT DAC7800 (Cont.)

DAC7800, 7801, 7802 5 SBAS005A www.ti.com LOGIC TRUTH TABLE BLOCK DIAGRAM PIN CONFIGURATION AGND A CS DB0 DB1 DB2 DB3 DB4 DB5 DGND AGND B I R V V UPD WR CLR DB7 DB6 OUT A FB A REF A FB B REF B DD OUT B DAC7801 I R V DAC7801 CLR UPD CS WR A1 A0 FUNCTION 1 1 1 X X X No Data Transfer 1 1 X 1 X X No Data Transfer

0 X X X X X All Registers Cleared

1 1 0 0 0 0 DAC A LS Input Register Loaded with DB7 - DB0 (LSB) 1 1 0 0 0 1 DAC A MS Input Register Loaded with DB3 (MSB) - DB0 1 1 0 0 1 0 DAC B LS Input Register Loaded with DB7 - DB0 (LSB) 1 1 0 0 1 1 DAC B MS Input Register Loaded with DB3 (MSB) - DB0 1 0 1 0 X X DAC A, DAC B Registers Updated Simultaneously from Input Registers 1 0 0 0 X X DAC A, DAC B Registers are Transparent X = Don’t care. TIMING CHARACTERISTICS VDD = +5V, VREF A = VREF B = +10V, TA = –40°C to +85°C. PARAMETER MINIMUM t1 — Address Valid to Write Setup Time 10ns t2 — Address Valid to Write Hold Time 10ns t3 — Data Setup Time 30ns t4 — Data Hold Time 10ns t5 — Chip Select or Update to Write Setup Time 0ns t6 — Chip Select or Update to Write Hold Time 0ns t7 — Write Pulse Width 40ns t8 — Clear Pulse Width 40ns A0–A1 CLR t2t1 WR CS, UPD t4t3 DATA NOTES: (1) All input signal rise and fall times are measured from 10% to 90% of +5V. t R = t F = 5ns. (2) Timing measurement reference level is .VIH + VIL DAC A I AGND A R V V R I AGND B OUT A FB A REF A REF B FB B OUT B VDD DAC A Register 4 8 DAC A LS Input Reg DAC A MS Input Reg Control Logic DAC B DAC B Register 4 8 DGND DAC B LS Input Reg DAC B MS Input Reg UPD CS WR CLR DAC7801 14 6 DB7 –DB0 Top View DIP

DAC7800, 7801, 78026 SBAS005Awww.ti.com BLOCK DIAGRAM AGND I R V CS A (LSB) DB0 DB1 DB2 DB3 DB4 DB5 DGND I R V V CS B WR DB11 (MSB) DB10 DB9 DB8 DB7 DB6 OUT A FB A REF A FB B REF B DD OUT B DAC7802 TIMING CHARACTERISTICS At VDD = +5V, and TA = –40oC to +85oC. PARAMETER MINIMUM t1 - Data Setup Time 20ns t2 - Data Hold Time 15ns t3 - Chip Select to Write Setup Time 30ns t4 - Chip Select to Write Hold Time 0ns t5 - Write Pulse Width 30ns LOGIC TRUTH TABLE CSA CSB WR FUNCTION X X 1 No Data Transfer 1 1 X No Data Transfer

0 A Rising Edge on CSA or CSB Loads

Data to the Respective DAC

01 DAC A Register Loaded from Data Bus

10 DAC B Register Loaded from Data Bus

00 DAC A and DAC B Registers Loaded

X = Don’t care. means rising edge triggered. PIN CONFIGURATION DAC7802 DATA 5V CSA, CSB WR t2t1 t3 t4 NOTES: (1) All input signal rise and fall times are measured from 10% to 90% of +5V. tR = tR = 5ns. (2) Timing measurement reference level is VIH + VIL 2 . CK DAC B DAC A DGND CS A 5 CS B 20 WR 19 VDD DAC7802 2 I 3 R OUT A FB A 23 R 24 I

1 AGND

DB11 –DB0 V V REF A REF B Top View DIP

DAC7800, 7801, 7802 7 SBAS005A www.ti.com TYPICAL CHARACTERISTICS OUTPUT OP AMP IS OPA602. TA = +25°C, VDD = +5V. Output Leakage Current (A) OUTPUT LEAKAGE CURRENT vs TEMPERATURE 100n 10n 100p 10p –75 –50 –25 0 +25 +50 +75 +100 +125 Temperature (°C) –60 –65 –70 –75 –80 –85 –90 –95 –100 THD + Noise (dB) THD + NOISE vs FREQUENCY Frequency (Hz) 1k10 100 10k 100k 1Vrms 3Vrms 6Vrms –20 –30 –40 –50 –60 –70 –80 –90 –100 –110 –120 Crosstalk (dB) CHANNEL-TO-CHANNEL ISOLATION vs FREQUENCY Frequency (Hz) 100k1k 10k 1M 10M –10 –20 –30 –40 –50 –60 –70 –80 –90 –100 Feedthrough (dB) FEEDTHROUGH vs FREQUENCY Frequency (Hz) 100k1k 10k 1M 10M +30 +20 +10 –10 –20 –30 –40 –50 Gain (dB) FREQUENCY RESPONSE Frequency (Hz) 100k1k 10k 1M 10M C F = 5pF C F = 10pF C F = 0pF Frequency (Hz) PSRR (dB) PSRR vs FREQUENCY –10 1k 10k 100k 1M DAC Loaded w/0s DAC Loaded w/1s

DAC7800, 7801, 780210 SBAS005Awww.ti.com If an application requires the DAC to have zero gain error, the circuit may be used, see Figure 6. Resistors R2 and R4 induce a positive gain error greater than worst-case initial negative gain error. Trim resistors R 1 and R 3 provide a variable negative gain error and have sufficient trim range to correct for the worst-case initial positive gain error plus the error produced by R 2 and R4. DATA INPUT ANALOG OUTPUT MSB ↓↓ LSB 1111 1111 1111 +V REF (2047/2048) 1000 0000 0001 +V REF (1/2048) 1000 0000 0000 0 Volts 0111 1111 1111 –V REF (1/2048) 0000 0000 0000 –VREF (2048/2048) TABLE III. Bipolar Output Code. FIGURE 5. Bipolar Configuration. DAC7802 has a single analog common, AGND. For a bipolar DAC with 13 bits of resolution, two solutions are possible. The addition of a precision difference amplifier and a high speed JFET switch provides a 12-bit plus sign voltage- output DAC, see Figure 7. When the switch selects the op amp output, the difference amplifier serves as a noninverting output buffer. If the analog ground side of the switch is selected, the output of the difference amplifier is inverted. Another option, see Figure 8, also produces a 12-bit plus sign output without the additional switch and digital control line. DIGITALLY PROGRAMMABLE ACTIVE FILTER See Figure 9 for the DAC780x in a digitally programmable active filter application. The design is based on the state- variable filter, Texas Instruments UAF42, an active filter topol- ogy that offers stable and repeatable filter characteristics. DAC1 and DAC2 can be updated in parallel with a single word to set the center frequency of the filter. DAC 4, which makes use of the uncommitted op amp in UAF42, sets the Q of the filter. DAC3 sets the gain of the filter transfer function without changing the Q of the filter. The reverse is also true. The center frequency is determined by f C = 1/2πRC where R is the ladder resistance of the DAC (typical value, 10kΩ ) and C the internal capacitor value (1000pF) of the UAF42. External capacitors can be added to lower the center frequency of the filter. But the highest center frequency for this circuit will be about 16kHz because the effective series resistance of the DAC cannot be less than 10kΩ . Note that the ladder resistance of the DAC may vary from device to device. Thus, for best tracking, DAC2 and DAC3 should be in the same package. Some calibration may be necessary from one filter to another.

FIGURE 6. Bipolar Configuration with Gain Trim. DAC7802 has a single analog common, AGND. FIGURE 7. 12-Bit Plus Sign DAC. DAC7802 has a single analog common, AGND.

13 Bits

FIGURE 8. 13-Bit Bipolar DAC. DAC7802 has a single analog common, AGND. FIGURE 9. Digitally Programmable Universal Active Filter.

www.ti.com 11-Nov-2025 PACKAGING INFORMATION Orderable part number Status (1) Material type (2) Package | Pins Package qty | Carrier RoHS (3) Lead finish/ Ball material (4) MSL rating/ Peak reflow (5) Op temp (°C) Part marking (6) DAC7800KU Active Production SOIC (DW) | 16 40 | TUBE Yes NIPDAU Level-3-260C-168 HR -40 to 85 DAC7800KU DAC7800KU.A Active Production SOIC (DW) | 16 40 | TUBE Yes NIPDAU Level-3-260C-168 HR -40 to 85 DAC7800KU DAC7800KU/1K Active Production SOIC (DW) | 16 1000 | LARGE T&R Yes NIPDAU Level-3-260C-168 HR -40 to 85 DAC7800KU DAC7800KU/1K.A Active Production SOIC (DW) | 16 1000 | LARGE T&R Yes NIPDAU Level-3-260C-168 HR -40 to 85 DAC7800KU DAC7800LP NRND Production PDIP (N) | 16 25 | TUBE Yes Call TI N/A for Pkg Type -40 to 85 DAC7800LP DAC7800LP.A NRND Production PDIP (N) | 16 25 | TUBE Yes Call TI N/A for Pkg Type -40 to 85 DAC7800LP DAC7800LU NRND Production SOIC (DW) | 16 40 | TUBE Yes NIPDAU Level-3-260C-168 HR -40 to 85 DAC7800LU DAC7800LU.A NRND Production SOIC (DW) | 16 40 | TUBE Yes NIPDAU Level-3-260C-168 HR -40 to 85 DAC7800LU DAC7801KU Active Production SOIC (DW) | 24 25 | TUBE Yes NIPDAU Level-3-260C-168 HR -40 to 85 DAC7801KU DAC7801KU.A Active Production SOIC (DW) | 24 25 | TUBE Yes NIPDAU Level-3-260C-168 HR -40 to 85 DAC7801KU DAC7801KU/1K Active Production SOIC (DW) | 24 1000 | LARGE T&R Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7801KU DAC7801KU/1K.A Active Production SOIC (DW) | 24 1000 | LARGE T&R Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7801KU DAC7801LU Active Production SOIC (DW) | 24 25 | TUBE Yes NIPDAU Level-3-260C-168 HR -40 to 85 DAC7801LU DAC7801LU.A Active Production SOIC (DW) | 24 25 | TUBE Yes NIPDAU Level-3-260C-168 HR -40 to 85 DAC7801LU DAC7802KU Active Production SOIC (DW) | 24 25 | TUBE Yes NIPDAU Level-3-260C-168 HR -40 to 85 DAC7802KU DAC7802KU.A Active Production SOIC (DW) | 24 25 | TUBE Yes NIPDAU Level-3-260C-168 HR -40 to 85 DAC7802KU DAC7802KU/1K Active Production SOIC (DW) | 24 1000 | LARGE T&R Yes NIPDAU Level-3-260C-168 HR -40 to 85 DAC7802KU DAC7802KU/1K.A Active Production SOIC (DW) | 24 1000 | LARGE T&R Yes NIPDAU Level-3-260C-168 HR -40 to 85 DAC7802KU DAC7802LU Active Production SOIC (DW) | 24 25 | TUBE Yes NIPDAU Level-3-260C-168 HR -40 to 85 DAC7802LU DAC7802LU.A Active Production SOIC (DW) | 24 25 | TUBE Yes NIPDAU Level-3-260C-168 HR -40 to 85 DAC7802LU DAC7802LUG4 Active Production SOIC (DW) | 24 25 | TUBE Yes NIPDAU Level-3-260C-168 HR -40 to 85 DAC7802LU (1) Status: For more details on status, see our product life cycle. (2) Material type: When designated, preproduction parts are prototypes/experimental devices, and are not yet approved or released for full production. Testing and final process, including without limitation quality assurance, reliability performance testing, and/or process qualification, may not yet be complete, and this item is subject to further changes or possible discontinuation. If available for ordering, purchases will be subject to an additional waiver at checkout, and are intended for early internal evaluation purposes only. These items are sold without warranties of any kind. (3) RoHS values: Yes, No, RoHS Exempt. See the TI RoHS Statement for additional information and value definition. Addendum-Page 1

www.ti.com 11-Nov-2025 (4) Lead finish/Ball material: Parts may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two lines if the finish value exceeds the maximum column width. (5) MSL rating/Peak reflow: The moisture sensitivity level ratings and peak solder (reflow) temperatures. In the event that a part has multiple moisture sensitivity ratings, only the lowest level per JEDEC standards is shown. Refer to the shipping label for the actual reflow temperature that will be used to mount the part to the printed circuit board. (6) Part marking: There may be an additional marking, which relates to the logo, the lot trace code information, or the environmental category of the part. Multiple part markings will be inside parentheses. Only one part marking contained in parentheses and separated by a "~" will appear on a part. If a line is indented then it is a continuation of the previous line and the two combined represent the entire part marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2

PACKAGE MATERIALS INFORMATION www.ti.com 10-Aug-2026 TAPE AND REEL INFORMATION Reel Width (W1) REEL DIMENSIONS A0B0K0WDimension designed to accommodate the component lengthDimension designed to accommodate the component thicknessOverall width of the carrier tapePitch between successive cavity centersDimension designed to accommodate the component width TAPE DIMENSIONSK0 P1B0WA0Cavity QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE Pocket QuadrantsSprocket HolesQ1Q1Q2Q2Q3Q3Q4Q4User Direction of Feed P1ReelDiameter *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Reel Diameter (mm) Reel Width W1 (mm) (mm) (mm) (mm) (mm) W (mm) Pin1 Quadrant Pack Materials-Page 1

PACKAGE MATERIALS INFORMATION www.ti.com 10-Aug-2026 TAPE AND REEL BOX DIMENSIONS Width (mm) W LH *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) DAC7800KU/1K SOIC DW 16 1000 350.0 350.0 43.0 DAC7801KU/1K SOIC DW 24 1000 350.0 350.0 43.0 DAC7802KU/1K SOIC DW 24 1000 350.0 350.0 43.0 Pack Materials-Page 2

PACKAGE MATERIALS INFORMATION www.ti.com 10-Aug-2026 TUBE L - Tube length T - Tube height W - Tube width B - Alignment groove width *All dimensions are nominal Device Package Name Package Type Pins SPQ L (mm) W (mm) T (µm) B (mm) DAC7800KU DW SOIC 16 40 506.98 12.7 4826 6.6 DAC7800KU.A DW SOIC 16 40 506.98 12.7 4826 6.6 DAC7800LP N PDIP 16 25 506 13.97 11230 4.32 DAC7800LP.A N PDIP 16 25 506 13.97 11230 4.32 DAC7800LU DW SOIC 16 40 506.98 12.7 4826 6.6 DAC7800LU.A DW SOIC 16 40 506.98 12.7 4826 6.6 DAC7801KU DW SOIC 24 25 506.98 12.7 4826 6.6 DAC7801KU.A DW SOIC 24 25 506.98 12.7 4826 6.6 DAC7801LU DW SOIC 24 25 506.98 12.7 4826 6.6 DAC7801LU.A DW SOIC 24 25 506.98 12.7 4826 6.6 DAC7802KU DW SOIC 24 25 506.98 12.7 4826 6.6 DAC7802KU.A DW SOIC 24 25 506.98 12.7 4826 6.6 DAC7802LU DW SOIC 24 25 506.98 12.7 4826 6.6 DAC7802LU.A DW SOIC 24 25 506.98 12.7 4826 6.6 DAC7802LUG4 DW SOIC 24 25 506.98 12.7 4826 6.6 Pack Materials-Page 3

www.ti.com GENERIC PACKAGE VIEW This image is a representation of the package family, actual package may vary. Refer to the product data sheet for package details. SOIC - 2.65 mm max heightDW 16 SMALL OUTLINE INTEGRATED CIRCUIT7.5 x 10.3, 1.27 mm pitch 4224780/A

www.ti.com PACKAGE OUTLINE C TYP10.63 9.97

2.65 MAX

14X 1.27 16X 0.51 0.31 8.89 TYP0.33 0.10 0 - 8 0.3 0.1 (1.4) 0.25 GAGE PLANE 1.27 0.40 A NOTE 3 10.5 10.1 B NOTE 4 7.6 7.4 4220721/A 07/2016 SOIC - 2.65 mm max heightDW0016A SOIC NOTES: 1. All linear dimensions are in millimeters. Dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed 0.15 mm, per side. 4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm, per side. 5. Reference JEDEC registration MS-013. 1 16

0.25 C A B

0.1 C SEE DETAIL A DETAIL A TYPICAL SCALE 1.500

www.ti.com EXAMPLE BOARD LAYOUT

0.07 MAX

0.07 MIN

(9.3) 14X (1.27) R0.05 TYP 16X (2) 16X (0.6) 4220721/A 07/2016 SOIC - 2.65 mm max heightDW0016A SOIC NOTES: (continued) 6. Publication IPC-7351 may have alternate designs. 7. Solder mask tolerances between and around signal pads can vary based on board fabrication site. METAL SOLDER MASK OPENING NON SOLDER MASK DEFINED SOLDER MASK DETAILS OPENING SOLDER MASK METAL SOLDER MASK DEFINED LAND PATTERN EXAMPLE SCALE:7X SYMM 8 9 SEE DETAILS SYMM

www.ti.com EXAMPLE STENCIL DESIGN R0.05 TYP 16X (2) 16X (0.6) 14X (1.27) (9.3) 4220721/A 07/2016 SOIC - 2.65 mm max heightDW0016A SOIC NOTES: (continued) 8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 9. Board assembly site may have different recommendations for stencil design. SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE:7X SYMM SYMM 8 9

IMPORTANT NOTICE AND DISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, regulatory or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you fully indemnify TI and its representatives against any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI’s products are provided subject to TI’s Terms of Sale, TI’s General Quality Guidelines, or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products. Unless TI explicitly designates a product as custom or customer-specified, TI products are standard, catalog, general purpose devices. TI objects to and rejects any additional or different terms you may propose. IMPORTANT NOTICE Copyright © 2026, Texas Instruments Incorporated Last updated 10/2025