16-Bit, Voltage Output, Serial Input Digital-To-Analog Converter datasheet (Rev. B)

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 23

Technical content

16-Bit, Voltage Output, Serial Input DIGITAL-TO-ANALOG CONVERTER

DESCRIPTION

The DAC7731 is a 16-bit Digital-to-Analog Converter (DAC) which provides 16 bits of monotonic performance over the specified operating temperature range and offers a +10V internal reference. Designed for automatic test equipment and industrial process control applications, the DAC7731 output swing can be configured in a ±10V, ±5V, or +10V range. The flexibility of the output configuration allows the DAC7731 to provide both unipolar and bipolar operation by pin strapping. The DAC7731 includes a high-speed output amplifier with a maximum settling time of 5µs to ±0.003% FSR for a 20V full-scale change and only consumes 100mW (typical) of power. The DAC7731 features a standard 3-wire, SPI-compatible serial interface with double buffering to allow asynchronous updates of the analog output as well as a serial data output line for daisy-chaining multiple DAC7731s. A user program- mable reset control forces the DAC output to either min-scale (0000 h) or mid-scale (8000h), overriding both the input and DAC register values. The DAC7731 is available in a SSOP-24 package and three performance grades specified to operate from –40°C to +85°C.

FEATURES

G LOW POWER: 150mW MAXIMUM G +10V INTERNAL REFERENCE G UNIPOLAR OR BIPOLAR OPERATION G SETTLING TIME: 5µs to ±0.003% FSR G 16-BIT MONOTONICITY, –40°C TO +85°C G ±10V, ±5V, OR +10V CONFIGURABLE VOLTAGE OUTPUT G RESET TO ZERO OR MID-SCALE G DOUBLE-BUFFERED DATA INPUT G DAISY-CHAIN FEATURE FOR MULTIPLE DAC7731s ON A SINGLE BUS G SMALL SSOP-24 PACKAGE

APPLICATIONS

G CLOSED-LOOP SERVO CONTROL G MOTOR CONTROL G DATA ACQUISITION SYSTEMS DAC7731 SBAS249B – DECEMBER 2001 – REVISED NOVEMBER 2007 www.ti.com Copyright © 2001-2007, Texas Instruments Incorporated Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Buffer +10V Reference Control Logic Enable Input Register DAC Register DAC REFEN RSTSEL RST LDAC SCLK CS SDO SDI VDD VSS VCC REFADJ REF OUT REF IN VREF R OFFSET RFB2 RFB1 SJ VOUT AGND DGND DAC7731 PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. All trademarks are the property of their respective owners.

SBAS249Bwww.ti.com ABSOLUTE MAXIMUM RATINGS (1) NOTE: (1) Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to absolute maximum conditions for extended periods may affect device reliability. ELECTROSTATIC DISCHARGE SENSITIVITY This integrated circuit can be damaged by ESD. Texas Instru- ments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION (1) SPECIFIED PACKAGE TEMPERATURE PACKAGE ORDERING TRANSPORT PRODUCT PACKAGE-LEAD DESIGNATOR RANGE MARKING NUMBER (2) MEDIA, QUANTITY DAC7731E SSOP-24 DB –40°C to +85°C DAC7731E DAC7731E Rails, 60 "" " " " DAC7731E/1K Tape and Reel,1000 DAC7731EB SSOP-24 DB –40°C to +85°C DAC7731EB DAC7731EB Rails, 60 "" " " " DAC7731EB/1K Tape and Reel, 1000 DAC7731EC SSOP-24 DB –40°C to +85°C DAC7731EC DAC7731EC Rails, 60 "" " " " DAC7731EC/1K Tape and Reel, 1000 NOTE: (1) For the most current package ordering information, see the Package Option Addendum at the end of this data sheet, or see the TI web site at www.ti.com. Top View SSOP PIN CONFIGURATION PIN NAME DESCRIPTION 1V CC Positive Analog Power Supply

2 REF OUT Internal Reference Output

4 REFADJ Internal Reference Trim. (Acts as a gain adjustment input when the internal reference is used.) 5V REF Buffered Output from REFIN, can be used to drive external devices. Internally, this pin directly drives the DAC's circuitry. OFFSET Offsetting Resistor

7 AGND Analog ground

8 RFB2 Feedback Resistor 2, used to configure DAC output

range.

9 RFB1 Feedback Resistor 1, used to configure DAC output

range.

10 SJ Summing Junction of the Output Amplifier

12 V DD Digital Power Supply

13 DGND Digital Ground

14 TEST Reserved, Connect to DGND

15 NC No Connection

16 RST V

OUT reset; active LOW, depending on the state of RSTSEL, the DAC register is either reset to mid- scale or min-scale. 17 LDAC DAC register load control, rising dege triggered. Data is loaded from the input register to the DAC register. 18 SDI Serial Data Input. Data is latched into the input register on the rising edge of SCLK. 19 SDO Serial Data Output, delayed 16 SCLK clock cycles.

20 CS Chip Select, Active LOW

21 SCLK Serial Clock Input

22 RSTSEL Reset Select; determines the action of RST. If HIGH, RST will reset the DAC register to mid-scale. If LOW, RST will reset the DAC register to min-scale.

23 REFEN Enables internal +10V reference (REF

OUT ), active LOW.

24 V SS Negative Analog Power Supply

V OUT VDD VSS REFEN RSTSEL SCLK CS SDO SDI LDAC RST NC TEST DGND DAC7731 NOTE: RST, LDAC, SDI, CS and SCK are Schmitt-triggered inputs.

SBAS249B www.ti.com DAC7731E DAC7731EB DAC7731EC PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX MIN TYP MAX UNITS ACCURACY Linearity Error (INL) ±6 ±4 ±3L S B TA = 25°C ±5 ±3 ±2L S B Differential Linearity Error (DNL) ±4 ±2 ±1L S B Monotonicity 14 15 16 Bits Offset Error ±0.1 ✻✻ % of FSR Offset Error Drift ±2 ✻✻ ppm/°C Gain Error With Internal REF ±0.4 ±0.25 ±0.15 % of FSR With External REF ±0.25 ±0.1 ✻ % of FSR Gain Error Drift With Internal REF ±15 ±10 ±7 ppm/ °C PSRR (V CC or VSS ) At Full-Scale 50 200 ✻✻ ✻ ✻ ppm/V ANALOG OUTPUT (1) Voltage Output(2) +11.4/–4.75 0 to 10 ✻✻ V +11.4/–6.4 ±5 ✻✻ V Output Current ±5 ✻✻ mA Output Impeadance 0.1 ✻✻ Ω Maximum Load Capacitance 200 ✻✻ pF Short-Circuit Current ±15 ✻✻ mA Short-Circuit Duration AGND Indefinite ✻✻ REFERENCE Reference Output 9.96 10 10.04 9.975 ✻ 10.025 ✻✻ ✻ V REF OUT Impedance 400 ✻✻ Ω REF OUT Voltage Drift ±15 ±10 ±7 ppm/ °C REF OUT Voltage Adjustment(3) ±25 ✻✻ mV REF IN Input Range(4) 4.75 V CC – 1.4 ✻✻ ✻ ✻ V REF IN Input Current 10 ✻✻ nA REFADJ Input Range Absolute Max Value that 01 0 ✻✻ ✻ ✻ V can be applied is VCC REFADJ Input Impedance 50 ✻✻ kΩ VREF Output Current –2+ 2 ✻✻ ✻ ✻ mA VREF Impedance 1 ✻✻ Ω DYNAMIC PERFORMANCE Settling Time to ±0.003% 20V Output Step 3 5 ✻✻ ✻ ✻ µs R L = 5kΩ , CL = 200pF, with external REFOUT to REFIN filter(5) Digital Feedthrough 2 ✻✻ nV-s Output Noise Voltage at 10kHz 100 ✻✻ nV/√Hz DIGITAL INPUT VIH |IH | < 10µA 0.7 • VDD ✻✻ V VIL |IL| < 10µA 0.3 • VDD ✻✻ V DIGITAL OUTPUT VOH IOH = –0.8mA 3.6 ✻✻ V VOL IOL = 1.6mA 0.4 ✻✻ V POWER SUPPLY VSS Bipolar Operation –15.75 –11.4 ✻✻ ✻ ✻ V Unipolar Opeation –15.75 –4.75 ✻✻ ✻ ✻ V IDD 100 ✻✻ µA ICC Unloaded 4 6 ✻✻ ✻ ✻ mA Power No Load, Ext. Reference 85 ✻✻ mW No Load, Int. Reference 100 150 ✻✻ ✻ ✻ mW TEMPERATURE RANGE Specified Performance –40 +85 ✻✻ ✻ ✻ °C ✻ Specifications same as grade to the left. NOTES: (1)With minimum VCC /VSS requirements, internal reference enabled. (2) Please refer to the Theory of Operation section for more information with respect to output voltage configurations. (3) See Figure 11 for gain and offset adjustment connection diagrams when using the internal reference. (4) The minimum value for REFIN must be equal to the greater of VSS +14V and +4.75V, where +4.75V is the minimum voltage allowed. (5) Reference low-pass filter values: 100kΩ , 1.0µF (see Figure 14).

ELECTRICAL CHARACTERISTICS

All specifications at TA = TMIN to TMAX , VCC = +15V, VSS = –15V, VDD = +5V, Internal refi⁄ence enabled, unless otherwise noted.

SBAS249Bwww.ti.com PARAMETER DESCRIPTION MIN TYP MAX UNITS tWH SCLK HIGH Time 25 ns tWL SCLK LOW Time 25 ns tSDI Setup Time: Data in valid before rising SCLK 5 ns tHDI Hold Time: Data in valid after rising SCLK 20 ns tSCS Setup Time: CS falling edge before first rising SCLK 15 ns tHSC Hold Time: CS rising edge after 16th rising SCLK 0 ns tDDO Delay Time: CS Falling Edge to Data Out valid, CL = 20pF on SDO 50 ns tHDO Hold Time: Data Out valid after SCLK rising edge, CL 20pF on SDO 50 ns tDDOZ Delay Time: CS rising edge to SDO = High Impedance 70 ns tWCSH CS HIGH Time 50 ns tWLDL LDAC LOW Time 20 ns tWLDH LDAC HIGH Time 20 ns tSLD Setup Time: 16th Rising SCLK Before LDAC Rising Edge 15 ns tDLD Delay Time: LDAC rising edge to first SCLK rising edge of next 15 ns transfer cycle. tSCLK Setup Time: CS High before falling SCLK edge following 16th 5 ns rising SCLK edge t SRS Setup Time: RSTSEL Valid Before RST LOW 0 ns tHRS Hold Time: RSTSEL valid after RST HIGH 20 ns tWRL RST LOW Time 30 ns tS DAC V OUT Settling Time 5 µs TIMING CHARACTERISTICS VCC = +15V, VSS = –15V, VDD = 5V; RL = 2kΩ to AGND; CL = 200pF to AGND; all specifications –40°C to +85°C, unless otherwise noted. DAC7731 CS SCLK SDI SDO LDAC VOUT tSCS tHCS tWH tWL tSCLKtHDItSDI tDDO tHDO tDDOZ tWLDL tDLD tSLD tS tWLDH tWCSH 12 1 6 B15 B14 B13 B0 A15 A14 A13 A0 C15 C14 C13 C12 B15 B14 B13 B12 Word B Word A Word C Word B ±0.003% of FSR Error Bands RSTSEL (RSTSEL = LOW) (RSTSEL = HIGH) RST VOUT VOUT tSRS tHRS tWRL tS+FS +FS –FS –FS Min-Scale Mid-Scale INTERFACE TIMING RESET TIMING

SBAS249B www.ti.com TYPICAL CHARACTERISTICS TA = +25°C (unless otherwise noted). 2.0 1.5 1.0 0.5 0.0 –0.5 –1.0 –1.5 –2.0 INL (LSB)DNL (LSB) LINEARITY ERROR AND DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 0000H 2000H 4000H 6000H 8000H Digital Input Code A000H C000 H E000H FFFF H Bipolar Configuration: VOUT = –10V to +10V TA = 85°C, Internal Reference Enabled 2.0 1.5 1.0 0.5 0.0 –0.5 –1.0 –1.5 –2.0 INL (LSB)DNL (LSB) LINEARITY ERROR AND DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 0000H 2000H 4000H 6000H 8000H Digital Input Code A000H C000 H E000H FFFF H Bipolar Configuration: VOUT = –10V to +10V TA = 25°C, Internal ReferenceEnabled 2.0 1.5 1.0 0.5 0.0 –0.5 –1.0 –1.5 –2.0 INL (LSB)DNL (LSB) LINEARITY ERROR AND DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 0000H 2000H 4000H 6000H 8000H Digital Input Code A000H C000 H E000H FFFF H Bipolar Configuration: VOUT = –10V to +10V TA = –40°C, Internal Reference Enabled Ext. Ref, Unipolar Mode: VOUT = 0 to +10V Int. Ref, Unipolar Mode: VOUT = 0 to +10V Ext. Ref, Bipolar Mode: VOUT = –10 to +10V Int. Ref, Bipolar Mode: VOUT = –10 to +10V 0.000 –0.010 –0.020 –0.030 –0.040 –0.050 –0.060 –0.070 –0.080 –0.090 –0.100 Error (%) –40 –15 10 35 60 85 Temperature (°C) GAIN ERROR vs TEMPERATURE Load = 200pF, 2kΩ 4.4 4.3 4.2 4.1 4.0 3.9 3.8 3.7 ICC (mA) 0000H 2000H 4000H 6000H 8000H Digital Input Code A000H C000 H E000H FFFF H VCC SUPPLY CURRENT vs DIGITAL INPUT CODE Bipolar Configuration: VOUT = –10V to +10V Internal Reference Enabled, TA = 25°C 1.00 0.75 0.50 0.25 0.00 –0.25 –0.50 –0.75 –1.00 Error (mV) OFFSET ERROR vs TEMPERATURE –40 –15 10 35 60 85 Temperature (°C) VOUT = 0 to +10V VOUT = –10 to +10V

SBAS249Bwww.ti.com TYPICAL CHARACTERISTICS (Cont.) TA = +25°C (unless otherwise noted). 3.4 3.3 3.2 3.1 3.0 2.9 2.8 2.7 ICC (mA) 0000H 2000H 4000H 6000H 8000H Digital Input Code A000H C000 H E000H FFFF H VCC SUPPLY CURRENT vs DIGITAL INPUT CODE Bipolar Configuration: VOUT = –10V to +10V External Reference, REFEN = 5V, TA = 25°C –1.50 –1.75 –2.00 –2.25 –2.50 –2.75 ISS (mA) 0000H 2000H 4000H 6000H 8000H Digital Input Code A000H C000 H E000H FFFF H VSS SUPPLY CURRENT vs DIGITAL INPUT CODE Bipolar Configuration: VOUT = –10V to +10V TA = 25°C SUPPLY CURRENT vs TEMPERATURE Load Current Excluded VCC = +15V, VSS = –15V Bipolar VOUT Configuration: –10V to +10V ICC ISS ICC , ISS (mA) –40 –15 10 35 60 85 Temperature (°C) 1800 1600 1400 1200 1000 800 600 400 200 IDD (µA) VLOGIC (V) SUPPLY CURRENT vs LOGIC INPUT VOLTAGE TA = 25°C, Transition Shown for a Single Input (Applies to CS, SCLK,D IN and LDAC inputs) 100 Frequency HISTOGRAM OF V CC CURRENT CONSUMPTION ICC (mA) Bipolar Output Configuration Internal Reference Enabled Code = 5555 H 100 Frequency HISTOGRAM OF V SS CURRENT CONSUMPTION ISS (mA) Bipolar Output Configuration Internal Reference Enabled Code = 5555 H

SBAS249B www.ti.com TYPICAL CHARACTERISTICS (Cont.) TA = +25°C (unless otherwise noted). –10 –20 –30 –40 –50 –60 –70 –80 PSRR (dB) 0.1K 1K 10K 100K 1M 10M Frequency (Hz) Bipolar Configuration: ±10V VOUT Code 8000H –VSS , VCC = 15V + 1Vp-p VDD = 5V + 0.5Vp-p VSS VCC VDD POWER-SUPPY REJECTION RATIO vs FREQUENCY (Measured at VOUT ) 10 –10 –20 –30 –40 –50 –60 –70 –80 PSRR (dB) 0.01K 0.1K 1K 10K 100K 1M 10M POWER-SUPPY REJECTION RATIO vs FREQUENCY (Measured at VOUT ) Frequency (Hz) VSS VCC VDD Bipolar Configuration: ±10V VOUT , Code FFFFH –VSS , VCC = 15V + 1Vp-p, VDD = 5V + 0.5Vp-p INTERNAL REFERENCE START-UP VCC (5V/div)REF OUT (2V/div) Time (2ms/div) 15V 10V 10.015 10.010 10.005 10.000 9.995 9.990 9.985 REF OUT (V) –40 –15 10 35 60 85 Temperature (°C) INTERNAL REFERENCE OUTPUT vs TEMPERATURE Source Sink OUTPUT VOLTAGE vs R LOAD –12 VOUT (V) R LOAD (kΩ) Loaded to VCC VCC = +15V Loaded to AGND 11.0 10.5 10.0 9.5 9.0 8.5 REF OUT (V) REF OUT LOAD(kΩ ) REF OUT VOLTAGE vs LOAD 1 10 100 1K

SBAS249Bwww.ti.com TYPICAL CHARACTERISTICS (Cont.) TA = +25°C (unless otherwise noted). 900 800 700 600 500 400 300 200 100 Output Noise (nV/Hz) 0.01K 0.1K 1K 10K 100K 1M 10M OUTPUT NOISE vs FREQUENCY Frequency (Hz) Unipolar Configuration, Internal Reference Enabled Code FFFFH Code 0000H 800 700 600 500 400 300 200 100 Output Noise (nV/rtHz) 0.01K 0.1K 1K 10K 100K 1M 10M OUTPUT NOISE vs FREQUENCY Frequency (Hz) Bipolar Configuration: ±10V, Internal Reference Enabled Code 0000H Code FFFFH Code 8000H BROADBAND NOISE VOUT (V, 50µV/div) Time (100µs/div) Internal Reference Enabled Filtered with 1.6Hz Low-Pass Code FFFF H , Bipolar ±10V Configuration 10kHz Measurement BW Unipolar Configuration: VOUT = 0 to +10V Zero-Scale to +Full-Scale Change 5kΩ , 200pF Load Large-Signal Output (5V/div) UNIPOLAR FULL-SCALE SETTLING TIME Time (2µs/div) Small-Signal Error (150µV/div) Bipolar Configuration: VOUT = –10 to +10V –Full-Scale to +Full-Scale 5kΩ , 200pF Load Large-Signal Output (5V/div) BIPOLAR FULL-SCALE SETTLING TIME Time (2µs/div) Small-Signal Error (300µV/div) –10 –20 –30 –40 –50 –60 –70 –80 PSRR (dB) 1 10 100 1K 10K 100K 1M 10M POWER-SUPPY REJECTION RATIO vs FREQUENCY (Measured at REFOUT ) Frequency (Hz) VSS VCC VDD Internal Reference Enabled SS , VCC = 15V + 1Vp-p, VDD = 5V + 0.5Vp-p

SBAS249B www.ti.com TYPICAL CHARACTERISTICS (Cont.) TA = +25°C (unless otherwise noted). Unipolar Configuration: VOUT = 0V to +10V +Full-Scale to Zero-Scale Change 5kΩ , 200pF Load Large-Signal Output (5V/div) UNIPOLAR FULL-SCALE SETTLING TIME Time (2µs/div) Small-Signal Error (150µV/div) Bipolar Configuration: VOUT = –10 to +10V +Full-Scale to –Full-Scale 5kΩ , 200pF Load Large-Signal Output (5V/div) BIPOLAR FULL-SCALE SETTLING TIME Time (2µs/div) Small-Signal Error (300µV/div) Code 8000H to 7FFFH Bipolar Configuration: ±10V VOUT MID-SCALE GLITCH Time (1µs/div) VOUT (V, 100mV/div) MID-SCALE GLITCH Time (1µs/div) VOUT (V, 100mV/div) Code 7FFFH to 8000H Bipolar Configuration: ±10V VOUT

FIGURE 4. Basic Operation: VOUT = –10V to +10V. rails, specified over the –40°C to +85°C temperature range. ±12V supplies with a typical 5% tolerance. operation of the device is not ensured.

1 Internal Reference disabled;

0 Internal Reference enabled;

information regarding the reset operation. H H X X X Shift Register is disabled on the serial bus. XH X ↑ X Data in Input Register is Loaded into DAC Register. X L H X X Resets Input and DAC Registers to mid-scale. X L L X X Resets Input and DAC Registers to min-scale. TABLE III. DAC7731 Logic Truth Table. TABLE II. DAC7731 Data Format. other system components requiring an external reference.

SBAS249Bwww.ti.com LAYOUT A precision analog component requires careful layout, adequate bypassing, and clean, well-regulated power supplies. The DAC7731 offers separate digital and analog supplies, as it will often be used in close proximity with digital logic, microcontrollers, microprocessors, and digital signal processors. The more digital logic present in the design and the higher the switching speed, the more important it will become to separate the analog and digital ground and supply planes at the device. Since the DAC7731 has both analog and digital ground pins, return currents can be better controlled and have less effect on the DAC output error. Ideally, AGND would be connected directly to an analog ground plane and DGND to the digital ground plane. The analog ground plane would be separate from the ground connection for the digital components until they were connected at the power-entry point of the system. The voltages applied to V CC and VSS should be well regulated and low noise. Switching power supplies and DC/DC convert- ers will often have high-frequency glitches or spikes riding on the output voltage. In addition, digital components can create similar high-frequency spikes as their internal logic switches states. This noise can easily couple into the DAC output voltage through various paths between the power connec- tions and analog output. In addition, a 1µF to 10µF bypass capacitor in parallel with a 0.1µF bypass capacitor is strongly recommended for each supply input. In some situations, additional bypassing may be required, such as a 100µF electrolytic capacitor or even a Pi filter made up of inductors and capacitors–all designed to essentially low-pass filter the analog supplies, removing any high frequency noise components.

www.ti.com 11-Nov-2025 PACKAGING INFORMATION Orderable part number Status (1) Material type (2) Package | Pins Package qty | Carrier RoHS (3) Lead finish/ Ball material (4) MSL rating/ Peak reflow (5) Op temp (°C) Part marking (6) DAC7731E Active Production SSOP (DB) | 24 60 | TUBE Yes NIPDAU Level-3-260C-168 HR -40 to 85 DAC7731E DAC7731E.A Active Production SSOP (DB) | 24 60 | TUBE Yes NIPDAU Level-3-260C-168 HR -40 to 85 DAC7731E DAC7731E/1K Active Production SSOP (DB) | 24 1000 | LARGE T&R Yes NIPDAU Level-3-260C-168 HR -40 to 85 DAC7731E DAC7731E/1K.A Active Production SSOP (DB) | 24 1000 | LARGE T&R Yes NIPDAU Level-3-260C-168 HR -40 to 85 DAC7731E DAC7731EB Active Production SSOP (DB) | 24 60 | TUBE Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7731E DAC7731EB.A Active Production SSOP (DB) | 24 60 | TUBE Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7731E DAC7731EB/1K Active Production SSOP (DB) | 24 1000 | LARGE T&R Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7731E DAC7731EB/1K.A Active Production SSOP (DB) | 24 1000 | LARGE T&R Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7731E DAC7731EC Active Production SSOP (DB) | 24 60 | TUBE Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7731E DAC7731EC.A Active Production SSOP (DB) | 24 60 | TUBE Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7731E DAC7731EC/1K Active Production SSOP (DB) | 24 1000 | LARGE T&R Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7731E DAC7731EC/1K.A Active Production SSOP (DB) | 24 1000 | LARGE T&R Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7731E DAC7731ECG4 Active Production SSOP (DB) | 24 60 | TUBE Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7731E (1) Status: For more details on status, see our product life cycle. (2) Material type: When designated, preproduction parts are prototypes/experimental devices, and are not yet approved or released for full production. Testing and final process, including without limitation quality assurance, reliability performance testing, and/or process qualification, may not yet be complete, and this item is subject to further changes or possible discontinuation. If available for ordering, purchases will be subject to an additional waiver at checkout, and are intended for early internal evaluation purposes only. These items are sold without warranties of any kind. (3) RoHS values: Yes, No, RoHS Exempt. See the TI RoHS Statement for additional information and value definition. (4) Lead finish/Ball material: Parts may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two lines if the finish value exceeds the maximum column width. (5) MSL rating/Peak reflow: The moisture sensitivity level ratings and peak solder (reflow) temperatures. In the event that a part has multiple moisture sensitivity ratings, only the lowest level per JEDEC standards is shown. Refer to the shipping label for the actual reflow temperature that will be used to mount the part to the printed circuit board. (6) Part marking: There may be an additional marking, which relates to the logo, the lot trace code information, or the environmental category of the part. Addendum-Page 1

www.ti.com 11-Nov-2025 Multiple part markings will be inside parentheses. Only one part marking contained in parentheses and separated by a "~" will appear on a part. If a line is indented then it is a continuation of the previous line and the two combined represent the entire part marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2

PACKAGE MATERIALS INFORMATION www.ti.com 10-Aug-2026 TAPE AND REEL INFORMATION Reel Width (W1) REEL DIMENSIONS A0B0K0WDimension designed to accommodate the component lengthDimension designed to accommodate the component thicknessOverall width of the carrier tapePitch between successive cavity centersDimension designed to accommodate the component width TAPE DIMENSIONSK0 P1B0WA0Cavity QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE Pocket QuadrantsSprocket HolesQ1Q1Q2Q2Q3Q3Q4Q4User Direction of Feed P1ReelDiameter *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Reel Diameter (mm) Reel Width W1 (mm) (mm) (mm) (mm) (mm) W (mm) Pin1 Quadrant Pack Materials-Page 1

PACKAGE MATERIALS INFORMATION www.ti.com 10-Aug-2026 TAPE AND REEL BOX DIMENSIONS Width (mm) W LH *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) DAC7731E/1K SSOP DB 24 1000 353.0 353.0 32.0 DAC7731EB/1K SSOP DB 24 1000 353.0 353.0 32.0 DAC7731EC/1K SSOP DB 24 1000 353.0 353.0 32.0 Pack Materials-Page 2

PACKAGE MATERIALS INFORMATION www.ti.com 10-Aug-2026 TUBE L - Tube length T - Tube height W - Tube width B - Alignment groove width *All dimensions are nominal Device Package Name Package Type Pins SPQ L (mm) W (mm) T (µm) B (mm) DAC7731E DB SSOP 24 60 530 10.5 4000 4.1 DAC7731E.A DB SSOP 24 60 530 10.5 4000 4.1 DAC7731EB DB SSOP 24 60 530 10.5 4000 4.1 DAC7731EB.A DB SSOP 24 60 530 10.5 4000 4.1 DAC7731EC DB SSOP 24 60 530 10.5 4000 4.1 DAC7731EC.A DB SSOP 24 60 530 10.5 4000 4.1 DAC7731ECG4 DB SSOP 24 60 530 10.5 4000 4.1 Pack Materials-Page 3

MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE 4040065 /E 12/01

28 PINS SHOWN

8,20 7,40 0,55 0,95 0,25 12,90 12,30 10,50 8,50 Seating Plane 9,907,90 10,50 9,90 0,38 5,60 5,00 0,22 A 2016 6,506,50 0,05 MIN 5,905,90 DIM A MAX A MIN PINS ** 2,00 MAX 6,90 7,50 0,65 M0,15 0°–/C02578° 0,10 0,09 0,25 NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. C. Body dimensions do not include mold flash or protrusion not to exceed 0,15. D. Falls within JEDEC MO-150

IMPORTANT NOTICE AND DISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, regulatory or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you fully indemnify TI and its representatives against any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI’s products are provided subject to TI’s Terms of Sale, TI’s General Quality Guidelines, or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products. Unless TI explicitly designates a product as custom or customer-specified, TI products are standard, catalog, general purpose devices. TI objects to and rejects any additional or different terms you may propose. IMPORTANT NOTICE Copyright © 2026, Texas Instruments Incorporated Last updated 10/2025