DAC7724_14 TI1

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 21

Technical content

12-Bit Quad Voltage Output DIGITAL-TO-ANALOG CONVERTER DAC7724 DAC7725

DESCRIPTION

The DAC7724 and DAC7725 are 12-bit quad voltage output digital-to-analog converters with guaranteed 12-bit monotonic performance over the specified tem- perature range. They accept 12-bit parallel input data, have double-buffered DAC input logic (allowing simul- taneous update of all DACs), and provide a readback mode of the internal input registers. An asynchronous reset clears all registers to a mid-scale code of 800 H (DAC7724) or to a zero-scale of 000H (DAC7725). The DAC7724 and DAC7725 can operate from a single +15V supply, or from +15V and –15V supplies. Low power and small size per DAC make the DAC7724 and DAC7725 ideal for automatic test equipment, DAC-per-pin programmers, data acquisition systems, and closed-loop servo-control. The DAC7724 and DAC7725 are available in a PLCC-28 or a SO-28 package, and offer guaranteed specifications over the –40°C to +85°C temperature range.

FEATURES

l LOW POWER: 250mW max l SINGLE SUPPLY OUTPUT RANGE: +10V l DUAL SUPPLY OUTPUT RANGE: ±10V l SETTLING TIME: 10µs to 0.012% l 12-BIT LINEARITY AND MONOTONICITY: –40°C to +85°C l RESET TO MID-SCALE (DAC7724) OR ZERO-SCALE (DAC7725) l DATA READBACK l DOUBLE-BUFFERED DATA INPUTS

APPLICATIONS

l CLOSED-LOOP SERVO-CONTROL l MOTOR CONTROL l DATA ACQUISITION SYSTEMS © 1999 Burr-Brown Corporation PDS-1517B Printed in U.S.A. April, 2000 International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 Twx: 910-952-1111 • Internet: http://www.burr-brown.com/ • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132 DAC ADAC Register A Input Register A I/O Buffer Control Logic DAC BDAC Register B Input Register B DAC CDAC Register C Input Register C DAC DDAC Register D Input Register D VREFHVCCVDD VSS VOUTD VOUTC VOUTB VOUTA VREFLRESET LDAC GND R/W CS DB0-DB11 For most current data sheet and other product information, visit www.burr-brown.com DAC7724 DAC7725 SBAS112

DAC7724, 7725 SPECIFICATION (DUAL SUPPLY) At TA = –40°C to +85°C, VCC = +15V, VDD = +5V, VSS = –15V, VREFH = +10V, VREFL = –10V, unless otherwise noted. The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. DAC7724N, U DAC7724NB, UB DAC7725N, U DAC7725NB, UB PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS ACCURACY Linearity Error ±2 ±1 LSB (1) Linearity Matching(2) ±2 ±1 LSB Differential Linearity Error ±1 ±1 LSB Monotonicity T MIN to TMAX 12 [ Bits Zero-Scale Error Code = 000 H ±2 [ LSB Zero-Scale Drift 1 [ ppm/°C Zero-Scale Matching(2) ±2 ±1 LSB Full-Scale Error Code = FFF H ±2 [ LSB Full-Scale Matching(2) ±2 ±1 LSB Power Supply Sensitivity At Full Scale 10 [ ppm/V ANALOG OUTPUT Voltage Output(3) VREFL VREFH [[ V Output Current ±5 [[ mA Load Capacitance No Oscillation 500 [ pF Short-Circuit Current ±20 [ mA Short-Circuit Duration To V SS , VCC , or GND Indefinite [ REFERENCE INPUT VREFH Input Range VREFL +1.25 +10 [[ V VREFL Input Range –10 VREFH – 1.25 [[ V Ref High Input Current –0.5 3.0 [[ mA Ref Low Input Current –3.5 0 [[ mA DYNAMIC PERFORMANCE Settling Time To ±0.012%, 20V Output Step 8 10 [[ µs Channel-to-Channel Crosstalk Full-Scale Step 0.25 [ LSB Digital Feedthrough 2 [ nV-s Output Noise Voltage f = 10kHz 65 [ nV/√Hz DIGITAL INPUT/OUTPUT Logic Family TTL-Compatible CMOS [ Logic Levels VIH IIH ≤ ±10µA 2.4 V DD +0.3 [[ V VIL IIL ≤ ±10µA –0.3 0.8 [[ V VOH IOH = –0.8mA 3.6 V DD [[ V VOL IOL = 1.6mA 0.0 0.4 [[ V Data Format Straight Binary [ POWER SUPPLY REQUIREMENTS IDD 50 [[ µA ICC 6 8.5 [[ mA ISS –8 –6 [[ mA Power Dissipation 180 250 [[ mW TEMPERATURE RANGE Specified Performance –40 +85 [[ °C NOTES: (1) LSB means Least Significant Bit, when VREFH equals +10V and VREFL equals –10V, then one LSB equals 4.88mV. (2) All DAC outputs will match within the specified error band. (3) Ideal output voltage, does not take into account zero or full-scale error.

DAC7724, 7725 SPECIFICATION (SINGLE SUPPLY) At TA = –40°C to +85°C, VCC = +15V, VDD = +5V, VSS = GND, VREFH = +10V, VREFL = 0V, unless otherwise noted. DAC7724N, U DAC7724NB, UB DAC7725N, U DAC7725NB, UB PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS ACCURACY Linearity Error(1) ±2 ±1 LSB (2) Linearity Matching(3) ±2 ±1 LSB Differential Linearity Error ±1 ±1 LSB Monotonicity T MIN to TMAX 12 [ Bits Zero-Scale Error Code = 004 H ±4 [ LSB Zero-Scale Drift 2 [ ppm/°C Zero-Scale Matching(3) ±4 ±2 LSB Full-Scale Error Code = FFF H ±4 [ LSB Full-Scale Matching(3) ±4 ±2 LSB Power Supply Sensitivity At Full Scale 20 [ ppm/V ANALOG OUTPUT Voltage Output(4) VREFL VREFH [[ V Output Current ±5 [ mA Load Capacitance No Oscillation 500 [ pF Short-Circuit Current ±20 [ mA Short-Circuit Duration To V CC or GND Indefinite [ REFERENCE INPUT VREFH Input Range VREFL +1.25 +10 [[ V VREFL Input Range 0 VREFH – 1.25 [[ V Ref High Input Current –0.3 1.5 [[ mA Ref Low Input Current –2.0 0 [[ mA DYNAMIC PERFORMANCE Settling Time(5) To ±0.012%, 10V Output Step 8 10 [[ µs Channel-to-Channel Crosstalk 0.25 [ LSB Digital Feedthrough 2 [ nV-s Output Noise Voltage f = 10kHz 65 [ nV/√Hz DIGITAL INPUT/OUTPUT Logic Family TTL-Compatible CMOS [ Logic Levels VIH IIH ≤ ±10µA 2.4 V DD +0.3 [[ V VIL IIL ≤ ±10µA –0.3 0.8 [[ V VOH IOH = –0.8mA 3.6 V DD [[ V VOL IOL = 1.6mA 0.0 0.4 [[ V Data Format Straight Binary [ POWER SUPPLY REQUIREMENTS VCC 14.25 15.75 [[ V IDD 50 [[ µA ICC 3.0 [[ mA Power Dissipation 45 [ mW TEMPERATURE RANGE Specified Performance –40 +85 [[ °C NOTES: (1) If VSS = 0V, specification applies at code 004H and above. (2) LSB means Least Significant Bit, when VREFH equals +10V and VREFL equals 0V, then one LSB equals 2.44mV. (3) All DAC outputs will match within the specified error band. (4) Ideal output voltage, does not take into account zero or full-scale error. (5) Full-scale positive 10V step and negative step from code FFFH to 004H .

DAC7724, 7725 RefH VSS VCC VDD VCC VSS VDD GND VOUT RefL 1 of 4 Typ of Each Logic Input Pin Typ of Each I/O Pin ABSOLUTE MAXIMUM RATINGS (1) NOTE: (1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. Exposure to absolute maximum conditions for extended periods may affect device reliability. ELECTROSTATIC DISCHARGE SENSITIVITY This integrated circuit can be damaged by ESD. Burr-Brown recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION MAXIMUM MAXIMUM LINEARITY DIFFERENTIAL PACKAGE SPECIFICATION ERROR NONLINEARITY ERROR DRAWING TEMPERATURE ORDERING TRANSPORT PRODUCT (LSB) (LSB) PACKAGE NUMBER RANGE NUMBER (1) MEDIA DAC7724N ±2 ±1 PLCC-28 251 –40 °C to +85°C DAC7724N Rails "" " "" " DAC7724N/750 Tape and Reel DAC7724NB ±1 ±1 PLCC-28 251 –40 °C to +85°C DAC7724NB Rails "" " "" " DAC7724NB/750 Tape and Reel DAC7724U ±2 ±1 SO-28 217 –40 °C to +85°C DAC7724U Rails "" " "" " DAC7724U/1K Tape and Reel DAC7724UB ±1 ±1 SO-28 217 –40 °C to +85°C DAC7724UB Rails "" " "" " DAC7724UB/1K Tape and Reel DAC7725N ±2 ±1 PLCC-28 251 –40 °C to +85°C DAC7725N Rails "" " "" " DAC7725N/750 Tape and Reel DAC7725NB ±1 ±1 PLCC-28 251 –40 °C to +85°C DAC7725NB Rails "" " "" " DAC7725NB/750 Tape and Reel DAC7725U ±2 ±1 SO-28 217 –40 °C to +85°C DAC7725U Rails "" " "" " DAC7725U/1K Tape and Reel DAC7725UB ±1 ±1 SO-28 217 –40 °C to +85°C DAC7725UB Rails "" " "" " DAC7725UB/1K Tape and Reel NOTE: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /750 indicates 750 devices per reel). Ordering 750 pieces of “DAC7724/750” will get a single 750-piece Tape and Reel. ESD PROTECTION CIRCUITS

DAC7724, 7725 Top View PIN CONFIGURATIONS PIN DESCRIPTIONS PIN NAME DESCRIPTION 1V REFH Reference Input Voltage High. Sets maximum output voltage for all DACs. 2V OUTB DAC B Voltage Output. 3V OUTA DAC A Voltage Output. 4V SS Negative Analog Supply Voltage, 0V or –15V. 5 GND Ground. 6 RESET Asynchronous Reset Input. Sets DAC and input registers to either mid-scale (800 H , DAC7724) or zero-scale (000H , DAC7725) when LOW. 7 LDAC Load DAC Input. All DAC Registers are transparent when LOW. 8 DB0 Data Bit 0. Least significant bit of 12-bit word.

9 DB1 Data Bit 1

10 DB2 Data Bit 2

11 DB3 Data Bit 3

12 DB4 Data Bit 4

13 DB5 Data Bit 5

14 DB6 Data Bit 6

15 DB7 Data Bit 7

16 DB8 Data Bit 8

17 DB9 Data Bit 9

18 DB10 Data Bit 10

19 DB11 Data Bit 11. Most significant bit of 12-bit word. 20 R/W Read/Write Control Input (read = HIGH, write = LOW). 21 A1 Register/DAC Select (C or D = HIGH, A or B = LOW). 22 A0 Register/DAC Select (B or D = HIGH, A or C = LOW). 23 CS Chip Select Input. 24 V DD Positive Digital Supply, +5V. 25 V CC Positive Analog Supply Voltage, +15V nominal. 26 V OUTD DAC D Voltage Output. 27 V OUTC DAC C Voltage Output. 28 V REFL Reference Input Voltage Low. Sets minimum output voltage for all DACs. V REFH VOUTB VOUTA VSS GND RESET LDAC (LSB) DB0 DB1 DB2 DB3 DB4 DB5 DB6 V REFL VOUTC VOUTD VCC VDD CS R/W DB11 (MSB) DB10 DB9 DB8 DB7 DAC7724 DAC7725 GND RESET LDAC (LSB) DB0 DB1 DB2 DB3 VCC VDD CS R/W DB11 (MSB) VSS VOUTA VOUTB VREFH VREFL VOUTC VOUTD DB4 DB5 DB6 DB7 DB8 DB9 DB10 4 3 2 1 28 27 26 12 13 14 15 16 17 18 DAC7724 DAC7725 SO PLCC

DAC7724, 7725 TYPICAL PERFORMANCE CURVES: V SS = 0V At TA = +25°C, VCC = +15V, VDD = +5V, VSS = 0V, VREFH = +10V, VREFL = 0V, representative unit, unless otherwise specified. 000H 200H 400H 600H 800H Digital Input Code A00H C00 H E00H FFF H LINEARITY ERROR AND DIFFERENTIAL LINEARITY ERROR vs CODE Single Channel 25°C (Typical of Each Output Channel) 0.50.4 0.3 0.2 0.10–0.1 –0.2 –0.3 –0.4 –0.5 0.50.4 0.3 0.2 0.10–0.1 –0.2 –0.3 –0.4 –0.5 LE (LSB)DLE (LSB) 0.50.4 0.3 0.2 0.10–0.1 –0.2 –0.3 –0.4 –0.5 0.50.4 0.3 0.2 0.10–0.1 –0.2 –0.3 –0.4 –0.5 LE (LSB)DLE (LSB) 000H 200H 400H 600H 800H Digital Input Code A00H C00 H E00H FFF H LINEARITY ERROR AND DIFFERENTIAL LINEARITY ERROR vs CODE Single Channel 85°C (Typical of Each Output Channel) 000H 200H 400H 600H 800H Digital Input Code A00H C00 H E00H FFF H LINEARITY ERROR AND DIFFERENTIAL LINEARITY ERROR vs CODE Single Channel –40°C (Typical of Each Output Channel) 0.50.4 0.3 0.2 0.10–0.1 –0.2 –0.3 –0.4 –0.5 0.5 0.4 0.3 0.2 0.1 –0.1 –0.2 –0.3 –0.4 –0.5 LE (LSB)DLE (LSB) –30 –20 –10 0 10 20 30 40 50 60 70 80 90–40 Temperature (°C) ZERO-SCALE ERROR vs TEMPERATURE (Code 004H ) Zero-Scale Error (mV) 2.0 1.5 1.0 0.5 –0.5 –1.0 –1.5 –2.0 DAC A DAC B DAC C DAC D –30 –20 –10 0 10 20 30 40 50 60 70 80 90–40 Temperature (°C) FULL-SCALE ERROR vs TEMPERATURE (Code FFFH ) Full-Scale Error (mV) 2.0 1.5 1.0 0.5 –0.5 –1.0 –1.5 –2.0 DAC A DAC B DAC C DAC D 1.2 1.0 0.8 0.6 0.4 0.2 –0.2 –0.4 –0.2 –0.4 –0.6 –0.8 –1.0 –1.2 –1.4 –1.6 VREF Current (mA)VREF Current (mA) 000H 200H 400H 600H 800H Digital Input Code A00H C00 H E00H FFF H CURRENT vs CODE All DACs Sent to Indicated Code VREFH VREFL

DAC7724, 7725 TYPICAL PERFORMANCE CURVES: V SS = 0V (Cont.) At TA = +25°C, VCC = +15V, VDD = +5V, VSS = 0V, VREFH = +10V, VREFL = 0V, representative unit, unless otherwise specified. 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 –0.5 POWER SUPPLY CURRENT vs TEMPERATURE Quiescent Current (mA) Temperature (°C) –40 –30 –20 –10 0 10 20 30 40 50 60 70 80 90 100 IDD ICC IDD ICC POSITIVE SUPPLY CURRENT vs DIGITAL INPUT CODE 3.00 2.50 2.00 1.50 1.00 0.50 ICC (mA) No Load 200H 400H 600H 800H A00H C00 H E00H FFF H000H Digital Input Code OUTPUT VOLTAGE MID-SCALE GLITCH PERFORMANCE Time (1µs/div) 800H to 7FFH +5V LDAC Output Voltage (200mV/div) OUTPUT VOLTAGE MID-SCALE GLITCH PERFORMANCE Time (1µs/div) 7FFH to 800H +5V LDAC Output Voltage (200mV/div) OUTPUT VOLTAGE vs SETTLING TIME (+10V to 0V) Time (2µs/div) Large Signal Settling Time: 5V/div +5V LDAC Small Signal Settling Time: 1LSB/div Output Voltage OUTPUT VOLTAGE vs SETTLING TIME (0V to +10V) Large Signal Settling Time: 5V/div Small Signal Settling Time: 1LSB/div +5V LDAC Output Voltage Time (2µs/div)

DAC7724, 7725 TYPICAL PERFORMANCE CURVES: V SS = 0V (Cont.) At TA = +25°C, VCC = +15V, VDD = +5V, VSS = 0V, VREFH = +10V, VREFL = 0V, representative unit, unless otherwise specified. +15V +5V POWER SUPPLY REJECTION RATIO vs FREQUENCY Frequency (Hz) PSRR (dB) –10 –20 –30 –40 –50 –60 –70 –80 –90 –100 –110 –120 2 103 104 105 106101 SINGLE SUPPLY CURRENT LIMIT vs INPUT CODE –10 –15 –20 IOUT (mA) 200H 400H 600H 800H A00H C00 H E00H FFF H000H Digital Input Code Short to Ground Short to VCC R LOAD (kW) 0.01 0.1 1 10 100 OUTPUT VOLTAGE vs R LOAD VOUT (V) Source Sink LOGIC SUPPLY CURRENT vs LOGIC INPUT LEVEL FOR DATA BITS Logic Input Level for Data Bits (V) Logic Supply Current (mA) OUTPUT NOISE vs FREQUENCY Frequency (kHz) Noise (nV/√Hz) 1000 100 0.1 1 10 100 1000 100000 Code 004H Code FFFH

DAC7724, 7725 TYPICAL PERFORMANCE CURVES: V SS = –15V At TA = +25°C, VCC = +15V, VDD = +5V, VSS = –15V, VREFH = +10V, VREFL = –10V, representative unit, unless otherwise specified. –30 –20 –10 0 10 20 30 40 50 60 70 80 90–40 Temperature (°C) POSITIVE FULL-SCALE ERROR vs TEMPERATURE (Code FFFH ) Positive Full-Scale Error (mV) 2.0 1.5 1.0 0.5 –0.5 –1.0 –1.5 –2.0 DAC A DAC B DAC C DAC D –30 –20 –10 0 10 20 30 40 50 60 70 80 90–40 Temperature (°C) BIPOLAR ZERO-SCALE ERROR vs TEMPERATURE (Code 800H ) Bipolar Zero-Scale Error (mV) DAC A DAC B DAC C DAC D 2.0 1.5 1.0 0.5 –0.5 –1.0 –1.5 –2.0 2.5 2.0 1.5 1.0 0.5 –0.5 VREF Current (mA) CURRENT vs CODE All DACs Sent to Indicated Code VREFH VREFL 000H 200H 400H 600H 800H Digital Input Code A00H C00 H E000H FFF H –0.5 –1.0 –1.5 –2.0 –2.5 –3.0 VREF Current (mA) 000H 200H 400H 600H 800H Digital Input Code A00H C00 H E00H FFF H LINEARITY ERROR AND DIFFERENTIAL LINEARITY ERROR vs CODE Single Channel –40°C (Typical of Each Output Channel) 0.50.4 0.3 0.2 0.10–0.1 –0.2 –0.3 –0.4 –0.5 0.50.4 0.3 0.2 0.1 0–0.1 –0.2 –0.3 –0.4 –0.5 LE (LSB)DLE (LSB) 000H 200H 400H 600H 800H Digital Input Code A00H C00 H E00H FFF H LINEARITY ERROR AND DIFFERENTIAL LINEARITY ERROR vs CODE Single Channel 85°C (Typical of Each Output Channel) 0.50.4 0.3 0.2 0.10–0.1 –0.2 –0.3 –0.4 –0.5 0.50.4 0.3 0.2 0.10–0.1 –0.2 –0.3 –0.4 –0.5 LE (LSB)DLE (LSB) 000H 200H 400H 600H 800H Digital Input Code A00H C00 H E00H FFF H LINEARITY ERROR AND DIFFERENTIAL LINEARITY ERROR vs CODE Single Channel 25°C (Typical of Each Output Channel) 0.50.4 0.3 0.2 0.10–0.1 –0.2 –0.3 –0.4 –0.5 0.50.4 0.3 0.2 0.10–0.1 –0.2 –0.3 –0.4 –0.5 LE (LSB)DLE (LSB)

DAC7724, 7725 TYPICAL PERFORMANCE CURVES: V SS = –15V (Cont.) At TA = +25°C, VCC = +15V, VDD = +5V, VSS = –15V, VREFH = +10V, VREFL = –10V, representative unit, unless otherwise specified. OUTPUT VOLTAGE vs SETTLING TIME (+10V to –10V) Time (2µs/div) +5V LDAC Small Signal Settling Time: 0.5LSB/div Large Signal Settling Time: 5V/div Output Voltage OUTPUT VOLTAGE vs SETTLING TIME (–10V to +10V) Time (2µs/div) +5V LDAC Small Signal Settling Time: 0.5LSB/div Large Signal Settling Time: 5V/div Output Voltage –10 –15 R LOAD (kΩ ) 0.01 0.1 1 10 100 OUTPUT VOLTAGE vs R LOAD VOUT (V) Sink Source SUPPLY CURRENT vs CODE –6 Supply Current (mA) IDD ISS 200H 400H 600H 800H A00H C00 H E00H FFF H000H Digital Input Code Data = FFFH (all DACs) No Load ICC Data = FFFH (all DACs) No Load POWER SUPPLY CURRENT vs TEMPERATURE Quiescent Current (mA) Temperature (°C) –40 –30 –20 –10 0 10 20 30 40 50 60 70 80 90 ICC IDD ISS –30 –20 –10 0 10 20 30 40 50 60 70 80 90–40 Temperature (°C) NEGATIVE FULL-SCALE ERROR vs TEMPERATURE (Code 000H ) Negative Full-Scale Error (mV) DAC A DAC B DAC C DAC D 2.0 1.5 1.0 0.5 –0.5 –1.0 –1.5 –2.0

DAC7724, 7725 TYPICAL PERFORMANCE CURVES: V SS = –15V (Cont.) At TA = +25°C, VCC = +15V, VDD = +5V, VSS = –15V, VREFH = +10V, VREFL = –10V, representative unit, unless otherwise specified. BROADBAND NOISE Time (1ms/div) Noise Voltage (500µV/div) BW = 1MHz Code = 800H OUTPUT VOLTAGE MID-SCALE GLITCH PERFORMANCE Time (1µs/div) +5V LDAC Output Voltage (200mV/div) 7FFH to 800H 800H to 7FFH –15V +5V POWER SUPPLY REJECTION RATIO vs FREQUENCY Frequency (Hz) PSRR (dB) –10 –20 –30 –40 –50 –60 –70 –80 –90 –100 –110 –120 2 103 104 105 106101 +15V DUAL SUPPLY CURRENT LIMIT vs INPUT CODE SHORT TO GROUND –10 –15 –20 IOUT (mA) 200H 400H 600H 800H A00H C00 H E00H FFF H000H Digital Input Code Noise at any code OUTPUT NOISE vs FREQUENCY Frequency (kHz) Noise (nV/√Hz) 1000 100 0.1 1 10 100 1000 100000 DATA BUS FEEDTHROUGH GLITCH Time (0.5µs/div) +5V DATA BUS Output Voltage (20mV/div)

tional amplifier that serves as a buffer, as shown in Figure 1. Figures 2 and 3 for the basic operation of the DAC7724/25. FIGURE 1. DAC7724/25 Architecture. FIGURE 2. Basic Single-Supply Operation of the DAC7724/25.

5 GND

6 RESET

NOTE: (1) Reset LOW sets all DACs to code 800H on the DAC7724 and to code 000H on the DAC7725.

provided that VREFH is at least 1.25V greater than VREFL . of the device is not guaranteed. ESD protection diodes” (see page 4). FIGURE 3. Basic Dual-Supply Operation of the DAC7724/25. NOTE: (1) Reset LOW sets all DACs to code 800H on the DAC7724 and to code 000H on the DAC7725.

DAC7724, 7725 V OUT = V REFL + V REFH ±V REFL() ·N 4096 STATE OF SELECTED SELECTED STATE OF INPUT INPUT ALL DAC A1 A0 R/W CS RESET LDAC REGISTER REGISTER REGISTERS L(1) LLL H (2) L A Transparent Transparent L H L L H L B Transparent Transparent H L L L H L C Transparent Transparent H H L L H L D Transparent Transparent LLLLHH A Transparent Latched L H L L H H B Transparent Latched H L L L H H C Transparent Latched H H L L H H D Transparent Latched L L H L H H A Readback Latched L H H L H H B Readback Latched H L H L H H C Readback Latched H H H L H H D Readback Latched X(3) X X H H L NONE (All Latched) Transparent X X X H H H NONE (All Latched) Latched XXXXL X A L L Reset(4) Reset(4) NOTES: (1) L = Logic LOW. (2) H= Logic HIGH. (3) X = Don’t Care. (4) DAC7724 resets to 800H , DAC7725 resets to 000H . When RESET rises, all registers that are in their latched state retain the reset value. TABLE I. DAC7724 and DAC7725 Control Logic Truth Table. DIGITAL INTERFACE Table I shows the basic control logic for the DAC7724/25. Note that each internal register is level triggered and not edge triggered. When the appropriate signal is LOW, the register becomes transparent. When this signal is returned HIGH, the digital word currently in the register is latched. The first set of registers (the Input Registers) are triggered via the A0, A1, R/W, and CS inputs. Only one of these registers is transparent at any given time. The second set of registers (the DAC Registers) are all transparent when LDAC input is pulled LOW. Each DAC can be updated independently by writing to the appropriate Input Register and then updating the DAC Register. Alternatively, the entire DAC Register set can be configured as always transparent by keeping LDAC LOW— the DAC update will occur when the Input Register is written. The double buffered architecture is mainly designed so that each DAC Input Register can be written at any time and then all DAC output voltages updated simultaneously by pulling LDAC LOW. It also allows a DAC Input Register to be written to at any point and the DAC voltage to be synchro- nously changed via a trigger signal connected to LDAC. DIGITAL TIMING Figure 4 and Table II provide detailed timing for the digital interface of the DAC7724 and DAC7725. DIGITAL INPUT CODING The DAC7724 and DAC7725 input data is in straight binary format. The output voltage is given by the following equa- tion: where N is the digital input code. This equation does not include the effects of offset (zero-scale) errors.

TABLE II. Timing Specifications (TA = –40°C to +85°C). FIGURE 4. Digital Input and Output Timing.

www.ti.com 24-Aug-2014 Addendum-Page 1 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/Ball Finish (6) MSL Peak Temp (3) Op Temp (°C) Device Marking (4/5) Samples DAC7724N ACTIVE PLCC FN 28 37 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-245C-168 HR -40 to 85 DAC7724N DAC7724N/750 ACTIVE PLCC FN 28 750 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-245C-168 HR -40 to 85 DAC7724N DAC7724NB ACTIVE PLCC FN 28 37 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-245C-168 HR -40 to 85 DAC7724N B DAC7724NB/750 ACTIVE PLCC FN 28 750 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-245C-168 HR -40 to 85 DAC7724N B DAC7724NB/750G4 ACTIVE PLCC FN 28 750 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-245C-168 HR -40 to 85 DAC7724N B DAC7724NBG4 ACTIVE PLCC FN 28 37 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-245C-168 HR -40 to 85 DAC7724N B DAC7724U ACTIVE SOIC DW 28 20 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR -40 to 85 DAC7724U B DAC7724U/1K ACTIVE SOIC DW 28 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR -40 to 85 DAC7724U B DAC7724UB ACTIVE SOIC DW 28 20 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR -40 to 85 DAC7724U B DAC7724UB/1K ACTIVE SOIC DW 28 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR -40 to 85 DAC7724U B DAC7724UBG4 ACTIVE SOIC DW 28 20 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR -40 to 85 DAC7724U B DAC7724UG4 ACTIVE SOIC DW 28 20 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR -40 to 85 DAC7724U B DAC7725N ACTIVE PLCC FN 28 37 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-245C-168 HR -40 to 85 DAC7725N DAC7725NB ACTIVE PLCC FN 28 37 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-245C-168 HR -40 to 85 DAC7725N B DAC7725NB/750 ACTIVE PLCC FN 28 750 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-245C-168 HR -40 to 85 DAC7725N B DAC7725NB/750G4 ACTIVE PLCC FN 28 750 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-245C-168 HR -40 to 85 DAC7725N B DAC7725NBG4 ACTIVE PLCC FN 28 37 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-245C-168 HR -40 to 85 DAC7725N B

www.ti.com 24-Aug-2014 Addendum-Page 2 Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/Ball Finish (6) MSL Peak Temp (3) Op Temp (°C) Device Marking (4/5) Samples DAC7725U ACTIVE SOIC DW 28 20 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR -40 to 85 DAC7725U B DAC7725UB ACTIVE SOIC DW 28 20 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR -40 to 85 DAC7725U B DAC7725UB/1K ACTIVE SOIC DW 28 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR -40 to 85 DAC7725U B DAC7725UB/1KG4 ACTIVE SOIC DW 28 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR -40 to 85 DAC7725U B DAC7725UBG4 ACTIVE SOIC DW 28 20 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR -40 to 85 DAC7725U B DAC7725UG4 ACTIVE SOIC DW 28 20 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR -40 to 85 DAC7725U B (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device.

www.ti.com 24-Aug-2014 Addendum-Page 3 (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

*All dimensions are nominal Device Package Type Package Drawing Pins SPQ Reel Diameter (mm) Reel Width W1 (mm) (mm) (mm) (mm) (mm) W (mm) Pin1 Quadrant PACKAGE MATERIALS INFORMATION www.ti.com 18-Aug-2014 Pack Materials-Page 1

*All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) DAC7724N/750 PLCC FN 28 750 346.0 346.0 41.0 DAC7724NB/750 PLCC FN 28 750 346.0 346.0 41.0 DAC7724U/1K SOIC DW 28 1000 367.0 367.0 55.0 DAC7724UB/1K SOIC DW 28 1000 367.0 367.0 55.0 DAC7725NB/750 PLCC FN 28 750 346.0 346.0 41.0 DAC7725UB/1K SOIC DW 28 1000 367.0 367.0 55.0 PACKAGE MATERIALS INFORMATION www.ti.com 18-Aug-2014 Pack Materials-Page 2

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic”are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2014, Texas Instruments Incorporated