DAC7614 TI

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 18

Technical content

© 1998 Burr-Brown Corporation PDS-1445C Printed in U.S.A. December, 1998 Quad, Serial Input, 12-Bit, Voltage Output DIGITAL-TO-ANALOG CONVERTER

FEATURES

l LOW POWER: 20mW l UNIPOLAR OR BIPOLAR OPERATION l SETTLING TIME: 10ms to 0.012% l 12-BIT LINEARITY AND MONOTONICITY: –40°C to +85°C l USER SELECTABLE RESET TO MID- SCALE OR ZERO-SCALE l SECOND-SOURCE for DAC8420 l SMALL 20-LEAD SSOP PACKAGE

APPLICATIONS

l CLOSED-LOOP SERVO-CONTROL l MOTOR CONTROL l DATA ACQUISITION SYSTEMS

DESCRIPTION

The DAC7614 is a quad, serial input, 12-bit, voltage output digital-to-analog converter (DAC) with guar- anteed 12-bit monotonic performance over the –40°C to +85°C temperature range. An asynchronous reset clears all registers to either mid-scale (800 H ) or zero- scale (000H ), selectable via the RESETSEL pin. The device can be powered from a single +5V supply or from dual +5V and –5V supplies. International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 Twx: 910-952-1111 • Internet: http://www.burr-brown.com/ • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132 Low power and small size makes the DAC7614 ideal for process control, data acquisition systems, and closed-loop servo-control. The device is available in 16-pin plastic DIP, 16-lead SOIC, or 20-lead SSOP packages, and is guaranteed over the –40°C to +85°C temperature range. DAC ADAC Register A DAC BDAC Register B DAC CDAC Register C DAC DDAC Register D VREFHVDD VSS VOUTD VOUTC VOUTB VOUTA VREFL GND CLK CS SDI RESET RESETSELLOADDACS Serial-to- Parallel Shift Register DAC Select SBAS092

At TA = –40°C to +85°C, VDD = +5V, VSS = –5V, VREFH = +2.5V, and VREFL = –2.5V, unless otherwise noted. DAC7614E, P, U DAC7614EB, PB, UB PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS ACCURACY Linearity Error(1) VSS = 0V or –5V –2 –1 LSB (2) Linearity Matching(3) VSS = 0V or –5V –2 –1 LSB Differential Linearity Error V SS = 0V or –5V –1 –1 LSB Monotonicity 12 [ Bits Zero-Scale Error Code = 000 H –4 [ LSB Zero-Scale Drift 25 [[ ppm/°C Zero-Scale Matching(3) –2 –1 LSB Full-Scale Error Code = FFF H –4 [ LSB Full-Scale Matching(3) –2 –1 LSB Zero-Scale Error Code = 00A H , VSS = 0V –8 [ LSB Zero-Scale Drift V SS = 0V 5 10 [[ ppm/°C Zero-Scale Matching(3) VSS = 0V –4 –2 LSB Full-Scale Error Code = FFF H , VSS = 0V –8 [ LSB Full-Scale Matching(3) VSS = 0V –4 –2 LSB Power Supply Rejection 30 [ ppm/V ANALOG OUTPUT Voltage Output(4) VSS = 0V or –5V V REFL VREFH [[ V Output Current –1.25 +1.25 [[ mA Load Capacitance No Oscillation 100 [ pF Short-Circuit Current +5, –15 [ mA Short-Circuit Duration Indefinite [ REFERENCE INPUT VREFH Input Range V SS = 0V or –5V VREFL +1.25 +2.5 [[ V VREFL Input Range V SS = 0V 0 VREFH –1.25 [[ V VREFL Input Range V SS = –5V –2.5 VREFH –1.25 [[ V DYNAMIC PERFORMANCE Settling Time(5) To –0.012% 5 10 [[ ms Channel-to-Channel Crosstalk Full-Scale Step 0.1 [ LSB On Any Other DAC, RL = 2kW Output Noise Voltage Bandwidth: 0Hz to 1MHz 40 [ nV/ÖHz DIGITAL INPUT/OUTPUT Logic Family TTL-Compatible CMOS [ Logic Levels VIH | IIH | £ 10mA 2.4 V DD +0.3 [[ V VIL | IIL | £ 10mA –0.3 0.8 [[ V Data Format Straight Binary [ POWER SUPPLY REQUIREMENTS VDD 4.75 5.25 [[ V VSS If VSS „ 0V –5.25 –4.75 [[ V IDD 1.5 1.9 [[ mA ISS –2.1 –1.6 [[ mA Power Dissipation V SS = –5V 15 20 [[ mW VSS = 0V 7.5 10 [[ mW TEMPERATURE RANGE Specified Performance –40 +85 [[ °C The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. [ Specification same as grade to the left. NOTES: (1) If VSS = 0V, specification applies at code 00AH and above. (2) LSB means Least Significant Bit, with VREFH equal to +2.5V and VREFL equal to –2.5V, one LSB is 1.22mV. (3) All DAC outputs will match within the specified error band. (4) Ideal output voltage, does not take into account zero or full-scale error. (5) If VSS = –5V, full-scale step from code 000H to FFFH or vice-versa. If VSS = 0V, full-scale positive step from code 000H to FFFH and negative step from code FFF H to 00AH .

ABSOLUTE MAXIMUM RATINGS (1) NOTE: (1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. Exposure to absolute maximum conditions for extended periods may affect device reliability. ELECTROSTATIC DISCHARGE SENSITIVITY This integrated circuit can be damaged by ESD. Burr-Brown recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION MAXIMUM MAXIMUM LINEARITY DIFFERENTIAL PACKAGE SPECIFICATION ERROR LINEARITY DRAWING TEMPERATURE ORDERING TRANSPORT PRODUCT (LSB) (LSB) PACKAGE NUMBER (1) RANGE NUMBER (2) MEDIA DAC7614P –2 –1 16-Pin DIP 180 –40 °C to +85°C DAC7614P Rails DAC7614PB –1 """ " DAC7614PB Rails DAC7614U –2 –1 16-Lead SOIC 211 –40 °C to +85°C DAC7614U Rails "" """ " DAC7614U/1K Tape and Reel DAC7614UB –1 –1 16-Lead SOIC 211 –40 °C to +85°C DAC7614UB Rails "" """ " DAC7614UB/1K Tape and Reel DAC7614E –2 –1 20-Lead SSOP 334 –40 °C to +85°C DAC7614E Rails "" """ " DAC7614E/1K Tape and Reel DAC7614EB –1 –1 20-Lead SSOP 334 –40 °C to +85°C DAC7614EB Rails "" """ " DAC7614EB/1K Tape and Reel NOTES: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book. (2) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /1K indicates 1000 devices per reel). Ordering 1000 pieces of “DAC7614EB/1K” will get a single 1000-piece Tape and Reel. For detailed Tape and Reel mechanical information, refer to Appendix B of Burr-Brown IC Data Book.

PIN CONFIGURATION—P, U Packages Top View PDIP, SOIC PIN DESCRIPTIONS—P, U Packages PIN LABEL DESCRIPTION 1V DD Positive Analog Supply Voltage, +5V nominal. 2V OUTD DAC D Voltage Output 3V OUTC DAC C Voltage Output 4V REFL Reference Input Voltage Low. Sets minimum out- put voltage for all DACs. 5V REFH Reference Input Voltage High. Sets maximum out- put voltage for all DACs. 6V OUTB DAC B Voltage Output 7V OUTA DAC A Voltage Output 8V SS Negative Analog Supply Voltage, 0V or –5V nomi- nal.

9 GND Ground

10 SDI Serial Data Input

11 CLK Serial Data Clock

12 CS Chip Select Input

13 NIC Not Internally Connected.

14 LOADDACS The selected DAC register becomes transparent

when LOADDACS is LOW. It is in the latched state when LOADDACS is HIGH. 15 RESET Asynchronous Reset Input. Sets all DAC registers to either zero-scale (000 H ) or mid-scale (800H ) when LOW. RESETSEL determines which code is active.

16 RESETSEL When LOW, a LOW on RESET will cause all DAC

registers to be set to code 000H . When RESETSEL is HIGH, a LOW on RESET will set the registers to code 800H . PIN CONFIGURATION—E Package Top View SSOP PIN DESCRIPTIONS—E Package PIN LABEL DESCRIPTION 1V DD Positive Analog Supply Voltage, +5V nominal. 2V OUTD DAC D Voltage Output 3V OUTC DAC C Voltage Output 4V REFL Reference Input Voltage Low. Sets minimum out- put voltage for all DACs. 5 NIC Not Internally Connected. 6 NIC Not Internally Connected. REFH Reference Input Voltage High. Sets maximum out- put voltage for all DACs. 8V OUTB DAC B Voltage Output. 9V OUTA DAC A Voltage Output.

10 V SS Negative Analog Supply Voltage, 0V or –5V nomi-

nal.

11 GND Ground

12 SDI Serial Data Input

13 CLK Serial Data Clock

14 CS Chip Select Input

15 NIC Not Internally Connected. 16 NIC Not Internally Connected. 17 NIC Not Internally Connected.

18 LOADDACS The selected DAC register becomes transparent

when LOADDACS is LOW. It is in the latched state when LOADDACS is HIGH. 19 RESET Asynchronous Reset Input. Sets all DAC registers to either zero-scale (000 H ) or mid-scale (800H ) when LOW. RESETSEL determines which code is active.

20 RESETSEL When LOW, a LOW on RESET will cause all DAC

registers to be set to code 000H . When RESETSEL is HIGH, a LOW on RESET will set the registers to code 800H . V DD VOUTD VOUTC VREFL VREFH VOUTB VOUTA VSS RESETSEL RESET LOADDACS NIC CS CLK SDI GND DAC7614P, U V DD VOUTD VOUTC VREFL NIC NIC VREFH VOUTB VOUTA VSS RESETSEL RESET LOADDACS NIC NIC NIC CS CLK SDI GND DAC7614E

TYPICAL PERFORMANCE CURVES: V SS = 0V At TA = +25°C, VDD = +5V, VSS = 0V, VREFH = +2.5V, and VREFL = 0V, representative unit, unless otherwise specified. LINEARITY ERROR and DIFFERENTIAL LINEARITY ERROR vs CODE (DAC A) 200H000H Digital Input Code DLE (LSB) LE (LSB) 0.50 0.00 –0.25 –0.50 0.50 0.25 0.00 –0.50 –0.25 0.25 400H 600H 800H A00H C00 H E00H FFF H LINEARITY ERROR and DIFFERENTIAL LINEARITY ERROR vs CODE (DAC B) 000H Digital Input Code DLE (LSB) LE (LSB) 0.50 0.00 –0.25 –0.50 0.50 0.25 0.00 –0.50 –0.25 0.25 200H 400H 600H 800H A00H C00 H E00H FFF H LINEARITY ERROR and DIFFERENTIAL LINEARITY ERROR vs CODE (DAC C) 000H Digital Input Code DLE (LSB) LE (LSB) 0.50 0.00 –0.25 –0.50 0.50 0.25 0.00 –0.50 –0.25 0.25 200H 400H 600H 800H A00H C00 H E00H FFF H LINEARITY ERROR and DIFFERENTIAL LINEARITY ERROR vs CODE (DAC D) 000H Digital Input Code DLE (LSB) LE (LSB) 0.50 0.00 –0.25 –0.50 0.50 0.25 0.00 –0.50 –0.25 0.25 200H 400H 600H 800H A00H C00 H E00H FFF H LINEARITY ERROR vs CODE (DAC A, –40°C and +85°C) 000H Digital Input Code LE (LSB) LE (LSB) 0.50 0.00 –0.25 –0.50 0.50 0.25 0.00 –0.50 –0.25 0.25 +85°C –40°C 200H 400H 600H 800H A00H C00 H E00H FFF H LINEARITY ERROR vs CODE (DAC B, –40°C and +85°C) 000H Digital Input Code LE (LSB) LE (LSB) 0.50 0.00 –0.25 –0.50 0.50 0.25 0.00 –0.50 –0.25 0.25 +85°C –40°C 200H 400H 600H 800H A00H C00 H E00H FFF H

TYPICAL PERFORMANCE CURVES: V SS = 0V (CONT) At TA = +25°C, VDD = +5V, VSS = 0V, VREFH = +2.5V, and VREFL = 0V, representative unit, unless otherwise specified. LINEARITY ERROR vs CODE (DAC C, –40°C and +85°C) 000H Digital Input Code LE (LSB) LE (LSB) 0.50 0.00 –0.25 –0.50 0.50 0.25 0.00 –0.50 –0.25 0.25 +85°C –40°C 200H 400H 600H 800H A00H C00 H E00H FFF H LINEARITY ERROR vs CODE (DAC D, –40°C and +85°C) 000H Digital Input Code LE (LSB) LE (LSB) 0.50 0.00 –0.25 –0.50 0.50 0.25 0.00 –0.50 –0.25 0.25 +85°C –40°C 200H 400H 600H 800H A00H C00 H E00H FFF H POSITIVE SLEW RATE and SETTLING TIME –2 8 –1 Time (µs) A: Output Voltage (V) B: Output Voltage, Deviation from +2.5V (LSB) –0.25 2.25 1.75 2.75 1.25 0.75 0.25 0 1 2 3 4 5 6 7 LOADDACS A B NEGATIVE SLEW RATE and SETTLING TIME –2 8 –1 Time (µs) A: Output Voltage (V) B: Output Voltage, Deviation from Code 00AH (LSB) –0.25 2.25 1.75 2.75 1.25 0.75 0.25 0 1 2 3 4 5 6 7 LOADDACS A B

TYPICAL PERFORMANCE CURVES: V SS = –5V At TA = +25°C, VDD = +5V, VSS = –5V, VREFH = +2.5V, and VREFL = –2.5V, representative unit, unless otherwise specified. LINEARITY ERROR and DIFFERENTIAL LINEARITY ERROR vs CODE (DAC A) 000H Digital Input Code DLE (LSB) LE (LSB) 0.50 0.00 –0.25 –0.50 0.50 0.25 0.00 –0.50 –0.25 0.25 200H 400H 600H 800H A00H C00 H E00H FFF H LINEARITY ERROR and DIFFERENTIAL LINEARITY ERROR vs CODE (DAC B) 000H Digital Input Code DLE (LSB) LE (LSB) 0.50 0.00 –0.25 –0.50 0.50 0.25 0.00 –0.50 –0.25 0.25 200H 400H 600H 800H A00H C00 H E00H FFF H LINEARITY ERROR and DIFFERENTIAL LINEARITY ERROR vs CODE (DAC C) 000H Digital Input Code DLE (LSB) LE (LSB) 0.50 0.00 –0.25 –0.50 0.50 0.25 0.00 –0.50 –0.25 0.25 200H 400H 600H 800H A00H C00 H E00H FFF H LINEARITY ERROR and DIFFERENTIAL LINEARITY ERROR vs CODE (DAC D) 000H Digital Input Code DLE (LSB) LE (LSB) 0.50 0.00 –0.25 –0.50 0.50 0.25 0.00 –0.50 –0.25 0.25 200H 400H 600H 800H A00H C00 H E00H FFF H LINEARITY ERROR vs CODE (DAC A, –40°C and +85°C) 000H Digital Input Code LE (LSB) LE (LSB) 0.50 0.00 –0.25 –0.50 0.50 +85°C –40°C 0.25 0.00 –0.50 –0.25 0.25 200H 400H 600H 800H A00H C00 H E00H FFF H LINEARITY ERROR vs CODE (DAC B, –40°C and +85°C) 000H Digital Input Code LE (LSB) LE (LSB) 0.50 0.00 –0.25 –0.50 0.50 +85°C –40°C 0.25 0.00 –0.50 –0.25 0.25 200H 400H 600H 800H A00H C00 H E00H FFF H

TYPICAL PERFORMANCE CURVES: V SS = –5V (CONT) At TA = +25°C, VDD = +5V, VSS = –5V, VREFH = +2.5V, and VREFL = –2.5V, representative unit, unless otherwise specified. LINEARITY ERROR vs CODE (DAC C, –40°C and +85°C) 200H000H Digital Input Code LE (LSB) LE (LSB) 0.50 0.00 –0.25 –0.50 0.50 +85°C –40°C 0.25 0.00 –0.50 –0.25 0.25 400H 600H 800H A00H C00 H E00H FFF H 600 VREFH CURRENT vs CODE (All DACs Set to Indicated Code) 000H FFF H400H C00 H800H Digital Input Code VREH Current (µA) 100 200 300 400 500 NEGATIVE SLEW RATE and SETTLING TIME –2 8 –1 Time (µs) A: Output Voltage (V) B: Output Voltage, Deviation from –2.5V (LSB) 0 1 2 3 4 5 6 7 LOADDACS AB POSITIVE SLEW RATE and SETTLING TIME –2 8 –1 Time (µs) A: Output Voltage (V) B: Output Voltage, Deviation from +2.5V (LSB) 0 1 2 3 4 5 6 7 LOADDACS A B VREFL CURRENT vs CODE (All DACs Set to Indicated Code) 000H FFF H400H C00 H800H Digital Input Code VREL Current (µA) –600 –500 –400 –300 –200 –100 LINEARITY ERROR vs CODE (DAC D, –40˚C and +85˚C) 000H 200H Digital Input Code LE (LSB) LE (LSB) 0.50 0.00 –0.25 –0.50 0.50 +85˚C –40˚C 0.25 0.00 –0.50 –0.25 0.25 400H 600H 800H A00H C00 H E00H FFF H

offset voltage (essentially, the offset of the output op amp). operation of the device is not guaranteed. possible to the DAC7614 package is strongly recommended. FIGURE 3. DAC7614 Timing. TABLE I. Timing Specifications (TA = –40°C to +85°C).

1 LSB

A1 A0 LOADDACS RESET REGISTER REGISTER L(1) L L H A Transparent L H L H B Transparent H L L H C Transparent H H L H D Transparent X (2) X H H NONE (All Latched) X X X L ALL Reset (3) NOTES: (1) L = Logic LOW. (2) X = Don’t Care. (3) Resets to either 000H or 800H , per the RESETSEL state (LOW = 000H , HIGH = 800H ). When RESET rises, all registers that are in their latched state retain the reset value. TABLE II. Control Logic Truth Table. CS (1) CLK (1) LOADDACS RESET SERIAL SHIFT REGISTER H (2) X(3) H H No Change L(4) L H H No Change L ›(5) H H Advanced One Bit › L H H Advanced One Bit H (6) XL (7) H No Change H (6) XHL (8) No Change NOTES: (1) CS and CLK are interchangeable. (2) H = Logic HIGH. (3) X = Don’t Care. (4) L = Logic LOW (5) = Positive Logic Transition. (6) A HIGH value is suggested in order to avoid a “false clock” from advancing the shift register and changing the shift register. (7) If data is clocked into the serial register while LOADDACS is LOW, the selected DAC register will change as the shift register bits “flow” through A1 and A0. This will corrupt the data in each DAC register that has been erroneously selected. (8) RESET LOW causes no change in the contents of the serial shift register. TABLE III. Serial Shift Register Truth Table. Note that CS and CLK are combined with an OR gate and the output controls the serial-to-parallel shift register inter- nal to the DAC7614 (see the block diagram on the front of this data sheet). These two inputs are completely inter- changeable. In addition, care must be taken with the state of CLK when CS rises at the end of a serial transfer. If CLK is LOW when CS rises, the OR gate will provide a rising edge to the shift register, shifting the internal data one additional bit. The result will be incorrect data and possible selection of the wrong DAC. If both CS and CLK are used, then CS should rise only when CLK is HIGH. If not, then either CS or CLK can be used to operate the shift register. See Table III for more information. Digital Input Coding The DAC7614 input data is in Straight Binary format. The output voltage is given by the following equation: where N is the digital input code (in decimal). This equation does not include the effects of offset (zero-scale) or gain (full-scale) errors. (VREFH – VREFL ) • N 4096V OUT = VREFL +

equate bypassing, and clean, well-regulated power supplies. performance from the converter. point of the system (see Figure 4). FIGURE 4. Suggested Power and Ground Connections for a DAC7614 Sharing a +5V Supply with a Digital System.

www.ti.com 23-May-2025 PACKAGING INFORMATION Orderable part number Status (1) Material type (2) Package | Pins Package qty | Carrier RoHS (3) Lead finish/ Ball material (4) MSL rating/ Peak reflow (5) Op temp (°C) Part marking (6) DAC7614E Active Production SSOP (DB) | 20 70 | TUBE Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7614E DAC7614E.A Active Production SSOP (DB) | 20 70 | TUBE Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7614E DAC7614E/1K Active Production SSOP (DB) | 20 1000 | LARGE T&R Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7614E DAC7614E/1K.A Active Production SSOP (DB) | 20 1000 | LARGE T&R Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7614E DAC7614EB Active Production SSOP (DB) | 20 70 | TUBE Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7614E B DAC7614EB.A Active Production SSOP (DB) | 20 70 | TUBE Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7614E B DAC7614EB/1K Active Production SSOP (DB) | 20 1000 | LARGE T&R Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7614E DAC7614EB/1K.A Active Production SSOP (DB) | 20 1000 | LARGE T&R Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7614E DAC7614U Active Production SOIC (DW) | 16 40 | TUBE Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7614U DAC7614U.A Active Production SOIC (DW) | 16 40 | TUBE Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7614U DAC7614U/1K Active Production SOIC (DW) | 16 1000 | LARGE T&R Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7614U DAC7614U/1K.A Active Production SOIC (DW) | 16 1000 | LARGE T&R Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7614U DAC7614UB Active Production SOIC (DW) | 16 40 | TUBE Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7614U B DAC7614UB.A Active Production SOIC (DW) | 16 40 | TUBE Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7614U B DAC7614UB/1K Active Production SOIC (DW) | 16 1000 | LARGE T&R Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7614U DAC7614UB/1K.A Active Production SOIC (DW) | 16 1000 | LARGE T&R Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7614U DAC7614UBG4 Active Production SOIC (DW) | 16 40 | TUBE Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7614U B DAC7614UG4 Active Production SOIC (DW) | 16 40 | TUBE Yes Call TI Level-3-260C-168 HR -40 to 85 DAC7614U (1) Status: For more details on status, see our product life cycle. (2) Material type: When designated, preproduction parts are prototypes/experimental devices, and are not yet approved or released for full production. Testing and final process, including without limitation quality assurance, reliability performance testing, and/or process qualification, may not yet be complete, and this item is subject to further changes or possible discontinuation. If available for ordering, purchases will be subject to an additional waiver at checkout, and are intended for early internal evaluation purposes only. These items are sold without warranties of any kind. (3) RoHS values: Yes, No, RoHS Exempt. See the TI RoHS Statement for additional information and value definition. Addendum-Page 1

www.ti.com 23-May-2025 (4) Lead finish/Ball material: Parts may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two lines if the finish value exceeds the maximum column width. (5) MSL rating/Peak reflow: The moisture sensitivity level ratings and peak solder (reflow) temperatures. In the event that a part has multiple moisture sensitivity ratings, only the lowest level per JEDEC standards is shown. Refer to the shipping label for the actual reflow temperature that will be used to mount the part to the printed circuit board. (6) Part marking: There may be an additional marking, which relates to the logo, the lot trace code information, or the environmental category of the part. Multiple part markings will be inside parentheses. Only one part marking contained in parentheses and separated by a "~" will appear on a part. If a line is indented then it is a continuation of the previous line and the two combined represent the entire part marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2

PACKAGE MATERIALS INFORMATION www.ti.com 23-May-2025 TAPE AND REEL INFORMATION Reel Width (W1) REEL DIMENSIONS A0B0K0WDimension designed to accommodate the component lengthDimension designed to accommodate the component thicknessOverall width of the carrier tapePitch between successive cavity centersDimension designed to accommodate the component width TAPE DIMENSIONSK0 P1B0WA0Cavity QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE Pocket QuadrantsSprocket HolesQ1Q1Q2Q2Q3Q3Q4Q4User Direction of Feed P1ReelDiameter *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Reel Diameter (mm) Reel Width W1 (mm) (mm) (mm) (mm) (mm) W (mm) Pin1 Quadrant Pack Materials-Page 1

PACKAGE MATERIALS INFORMATION www.ti.com 23-May-2025 TAPE AND REEL BOX DIMENSIONS Width (mm) W LH *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) DAC7614E/1K SSOP DB 20 1000 356.0 356.0 35.0 DAC7614EB/1K SSOP DB 20 1000 356.0 356.0 35.0 DAC7614U/1K SOIC DW 16 1000 356.0 356.0 35.0 DAC7614UB/1K SOIC DW 16 1000 356.0 356.0 35.0 Pack Materials-Page 2

PACKAGE MATERIALS INFORMATION www.ti.com 23-May-2025 TUBE L - Tube length T - Tube height W - Tube width B - Alignment groove width *All dimensions are nominal Device Package Name Package Type Pins SPQ L (mm) W (mm) T (µm) B (mm) DAC7614E DB SSOP 20 70 530 10.5 4000 4.1 DAC7614E.A DB SSOP 20 70 530 10.5 4000 4.1 DAC7614EB DB SSOP 20 70 530 10.5 4000 4.1 DAC7614EB.A DB SSOP 20 70 530 10.5 4000 4.1 DAC7614U DW SOIC 16 40 507 12.83 5080 6.6 DAC7614U.A DW SOIC 16 40 507 12.83 5080 6.6 DAC7614UB DW SOIC 16 40 507 12.83 5080 6.6 DAC7614UB.A DW SOIC 16 40 507 12.83 5080 6.6 DAC7614UBG4 DW SOIC 16 40 507 12.83 5080 6.6 DAC7614UG4 DW SOIC 16 40 507 12.83 5080 6.6 Pack Materials-Page 3

IMPORTANT NOTICE AND DISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, regulatory or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products. TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2025, Texas Instruments Incorporated