D221I ETC1
Document overview
- Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
Key Features:
- 2W Output Power
- 3,000 VDC Isolation
- Miniature SIP Case
- Single & Dual Outputs
- >2 MHour MTBF
- 28 Standard Models
- Industry Standard Pin-Out MicroPower Direct
232 Tosca Drive
Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com D200I High IsolationHigh Isolation Miniature, 2W SIPMiniature, 2W SIP DC/DC Con vert ersDC/DC Con vert ers Series Electrical Specifi cations Specifi cations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice. Input Parameter Conditions Min. Typ. Max. Units Input Voltage Range 5 VDC Input 4.5 5.0 5.5 VDC12 VDC Input 10.8 12.0 13.2 24 VDC Input 21.6 24.0 26.4 48 VDC Input 42.0 48.0 52.0 Input Filter Internal Capacitor Reverse Polarity Input Current 0.3 A Output Parameter Conditions Min. Typ. Max. Units Output Voltage Accuracy ±1.0 ±3.0 % Output Voltage Balance Dual Output , Balanced Loads ±1.0 % Line Regulation For Vin Change of 1% ±1.2 % Load Regulation (Note 1) See Model Selection Guide Ripple & Noise (20 MHz) (Note 2) 75 mV P - P Output Power Protection 120 % Temperature Coeffi cient ±0.02 %/ºC Output Short Circuit Momentary (0.5 Sec.) General Parameter Conditions Min. Typ. Max. Units Isolation Voltage 60 Seconds 3,000 VDC Isolation Resistance 500 VDC 1,000 MΩ Isolation Capacitance 100 kHz, 1V 60 pF Switching Frequency 125 kHz Environmental Parameter Conditions Min. Typ. Max. Units Operating Temperature Range Ambient -40 +25 +85 ºC Operating Temperature Range Case +100 ºC Storage Temperature Range -40 +125 ºC Cooling Free Air Convection Humidity RH, Non-condensing 95 % Physical Case Material Non-Conductive Black Plastic (UL94-V0) Weight 0.09 Oz (2.7g) Reliability Specifi cations Parameter Conditions Min. Typ. Max. Units MTBF MIL HDBK 217F, 25ºC, Gnd Benign 2.0 MHours Absolute Maximum Ratings Parameter Conditions Min. Typ. Max. Units Input Voltage Surge (1 Sec) 5 VDC Input -0.7 9.0 VDC12 VDC Input -0.7 18.0 24 VDC Input -0.7 30.0 48 VDC Input -0.7 55.0 Lead Temperature 1.5 mm From Case For 10 Sec 260 ºC Internal Power Dissipation All Models 650 mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
Notes: All dimensions are typical in inches (mm) Tolerance x.xx = ±0.01 (±0.25) Pin 1 is marked by a “dot” or indentation on the side of the unit Notes: 1. Output load regulation is specifi ed for a load change of 20% to 100%. 2. When measuring output ripple, it is recommended that an external ceramic capacitor (approx 10 µF) be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. 3. All 3.3, 5 and ±5 VDC output models may be operated to +85ºC ambient with an unobstructed airfl ow of 3.6 ft/S (1.1 m/S). 4. The 5V, 12V and 24V input units do not require external components to operate, but the use of an input capacitor (10 µF) may enhance performance in some applications. An output capacitor (1.0 µF to 10 µF) may be used to reduce ripple. The 48V input models require an input capacitor of 4.7 uF to 47 uF (dependent upon the application). 5. Dual output units may be connected to provide a 10V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and fl oat the output common. 6. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating. Derating Curve MicroPower Direct www.micropowerdirect.com 232 Tosca Drive Stoughton, MA 02072 ■ TEL: (781) 344-8226 ■ FAX: (781) 344-8481 ■ E-Mail: sales@micropowerdirect.com Model Selection Guide Mechanical Dimensions Pin Connections Single Output (μF Max) 470 Dual Output (μF Max) ±390 Capacitive Load Model Number Input Output Load Regulation (%, Max) Effi ciency (%, Typ) Fuse Rating Slow-Blow (mA) Voltage (VDC) Current (mA) Voltage (VDC) Current (mA, Max) Current (mA, Min)Nominal Range Full-Load No-Load Pin Single Dual 1 +Vin +Vin 2 -Vin -Vin 5 -Vout -Vout