CX77105 SKYWORKS
Document overview
- PDF pages: 17
Technical content
Page 1
The CX77105, a dual-mode, Code Division Multiple Access (CDMA) / Advanced Mobile Phone Service (AMPS) Power Amplifier Module (PAM), is a fully matched, 10-pin surface mount module developed for cellular handsets and wireless local loop applications. This small and efficient power amplifier module packs a full 824–849 MHz bandwidth coverage into a single compact package. The device meets the stringent IS95 CDMA linearity requirements to and exceeding 28 dBm output power, and can be driven to levels beyond 31 dBm for high efficiency in FM mode operation. A low current digital pin (VCONT) provides improved efficiency for the low RF power range of operation.
The single Gallium Arsenide (GaAs) Microwave Monolithic Integrated Circuit (MMIC) contains all active circuitry in the module. The MMIC contains on-board bias circuitry, as well as input and interstage matching circuits. The output match is realized off-chip and within the module package to optimize efficiency and power performance into a 50 Ω load. This device is manufactured with Skyworks’ GaAs Heterojunction Bipolar Transistor (HBT) process that provides for all positive voltage DC supply operation while maintaining high efficiency and good linearity. Primary bias to the CX77105 is supplied directly from a three-cell nickel cadmium, a single-cell lithium ion, or other
suitable battery with an output in the 3–4 volt range. Power down is accomplished by setting the voltage on the low current reference pin to zero volts. No external supply side switch is needed as typical “off” leakage is a few microamperes with full primary voltage supplied from the battery.
Functional Block Diagram
Distinguishing Features
- Low voltage positive bias supply (3.2 V to 4.2 V, typical)
- Good linearity
- High efficiency
- Dual mode operation
- Large dynamic range
- 10-pin package (4 x 4 x 1.5 mm)
- Power down control
- Low power-state control
- InGaP
- IS 95/CDMA2000
Applications
- Digital cellular (CDMA)
- Analog cellular (AMPS)
- Wireless local loop (WLL)

Data Sheet © 2001, 2002 Skyworks Solutions, Inc., All Rights Reserved.
Page 2
Electrical Specifications
Electrical Specifications
The following tables list the electrical characteristics of the CX77105 Power Amplifier. Table 2 lists the recommended operating conditions for achieving the electrical performance listed in
Table 4. Table 3 lists the electrical performance of the CX77105 Power Amplifier over the recommended operating conditions.
Table 1. Absolute Maximum Ratings(1)
| Parameter | Symbol | Minimum | Nominal | Maximum | Unit |
|---|---|---|---|---|---|
| RF Input Power | PIN | — | 4.0 | 7.0 | dBm |
| Supply Voltage | VCC | — | 3.4 | 6.0 | Volts |
| Reference Voltage | VREF | — | 3.0 | 3.1 | Volts |
| Case Operating Temperature | TC | –30 | 25 | +110 | oC |
| Storage Temperature | TSTG | –55 | — | +125 | oC |
| NOTE(S): (1) No damage assuming only one parameter is set at limit at a time with all other parameters set at or below nominal value. | |||||
Table 2. Recommended Operating Conditions
| Parameter | Symbol | Minimum | Nominal | Maximum | Unit |
|---|---|---|---|---|---|
| Supply Voltage | VCC | 3.2 | 3.4 | 4.2 | Volts |
| PA On Reference Voltage PA Off | VREF | 2.95 | 3.0 | 3.05 | Volts |
| VREF | — | — | 0.5 | ||
| High Bias Mode Input Impedance >2.5 kΩ Low Bias | VCONT | 0.0 | — | 0.5 | Volts |
| VCONT | 2.5 | — | 3.0 | ||
| Operating Frequency | FO | 824.0 | 836.5 | 849.0 | MHz |
| Operating Temperature | TO | –30 | — | +85 | °C |
Table 3. Power Range Truth Table
| Power Mode | VREF | VCONT | Range |
| High Power | 3.0 V | 0.0–0.5 V | 16 dBm–28 dBm |
| Low Power | 3.0 V | 2.5–3.0 V | ≤ 16 dBm |
| Shut Down | 0.0 V | 0.0 V | — |
Page 3
Electrical Specifications
Table 4. Electrical Specifications for CDMA / AMPS Nominal Operating Conditions(1)

Page 4
Electrical Specifications
Table 4. Electrical Specifications for CDMA / AMPS Nominal Operating Conditions(1)
| Characteristics | Symbol | Condition | Minimum | Typical | Maximum | Unit |
|---|---|---|---|---|---|---|
| Noise Power in RX Band 869-894 MHz | RxBN | PO ≤ 28 dBm | — | –137 | — | dBm/Hz |
| Noise Figure | NF | — | — | 4.6 | 5.0 | dB |
| Input Voltage Standing Wave Ratio | VSWR | — | — | — | 1.9:1 | — |
| Stability (Spurious output) | S | 5:1 VSWR all phases | — | — | –60.0 | dBc |
| Ruggedness—No damage(4) | Ru | PO ≤ 28 dBm | 10:1 | — | — | VSWR |
| NOTE(S): (1) VCC = +3.4 V, VREF = +3.0 V, Freq = 836.5 MHz, TC = 25 °C, unless otherwise specified. (2) ACP is specified per IS95 as the ratio of the total in-band power (1.23 MHz BW) to adjacent power in a 30 kHz BW. (3) CDMA2000 is configured as DCCH = 9600, SCHO = 9600, PCH (Walsh 0) = – 3.75 dB, and Peak-to-Average Ratio (CCDF = 1%) = 4.5 dB. For CDMA2000, 0.5 dB back-off in output power is required. (4) All phases, time = 10 seconds. | ||||||
Table 5. Electrical Specifications for CDMA / AMPS Recommended Operating Conditions(1)

Page 5
Electrical Specifications
Table 5. Electrical Specifications for CDMA / AMPS Recommended Operating Conditions(1)
| Characteristics | Symbol | Condition | Minimum | Maximum | Unit |
|---|---|---|---|---|---|
| Noise Power in RX Band 869-894 MHz | RxBN | PO ≤ 28 dBm | — | –134.0 | dBm/Hz |
| Noise Figure | NF | — | — | 7.0 | dB |
| Input Voltage Standing Wave Ratio (VSWR) | VSWR | — | — | 2.0:1 | — |
| Stability (Spurious output) | S | 5:1 VSWR All phases | — | –60.0 | dBc |
| Ruggedness – No damage(4) | Ru | PO ≤ 28dBm | 10:1 | — | VSWR |
| NOTE(S): (1) Per Table 2, unless otherwise specified. (2) ACP is specified per IS95 as the ratio of the total in-band power (1.23 MHz BW) to adjacent power in a 30 kHz BW. (3) CDMA2000 is configured as DCCH = 9600, SCHO = 9600, PCH (Walsh 0) = –3.75 dB, and Peak-to-Average Ratio (CCDF = 1%) = 4.5 dB. For CDMA2000, 0.5 dB back-off in output power is required. (4) All phases, time = 10 seconds. | |||||
Page 6
Characterization Data
Characterization Data
The following graphs illustrate the characteristics of a typical CX77105 power amplifier designed for operation in the cellular frequency band (824–849 MHz). This amplifier was selected by
characterizing a group of devices and then selecting a part with average electrical performance for both nominal and the full range of recommended operating conditions, including worst case limits.
Figures 1 through 7 illustrate the digital signal characteristics of the CX77105. Shown are power sweep characteristics for key performance parameters, over temperature and frequency, up to 28.5
dBm output power. The data was taken up to and including 16 dBm output power with the bias mode control pin setting of VCONT = 2.5 volts. Beyond 16 dBm output power, the VCONT was set to 0 volts.
Figure 1. Digital Mode Gain vs. Output Power


Page 7
Characterization Data
Figure 2. Primary Bias Current vs. Output Power

Figure 3. Power Added Efficiency vs. Output Power


Page 8
Characterization Data
Figure 4. Adjacent Channel Power for 885 kHz Offset Current vs. Output Power

Figure 5. Adjacent Channel Power for 1.98 MHz Offset vs. Output Power


Page 9
Characterization Data
Figure 6. Second Harmonic Rejection vs. Output Power

Figure 7. Third Harmonic Rejection vs. Output Power


Page 10
Characterization Data
Figure 8. Noise Figure as Function of Operating Conditions


Page 11
Evaluation Board Description
Evaluation Board Description
The evaluation board is a platform for testing and interfacing design circuitry. To accommodate the interface testing of the CX77105, the evaluation board schematic and diagrams are included for preliminary analysis and design. Figure 10 shows the basic schematic of the board for the 824 MHz to 849 MHz range.
Figure 10. Evaluation Board Schematic

Figure 11. Evaluation Board Assembly Diagram





Page 12
Package Dimensions and Pin Descriptions
Package Dimensions and Pin Descriptions
The CX77105 is a multi-layer laminate base, overmold encapsulated modular package designed for surface mount solder attachment to a printed circuit board.
Figure 12 is a mechanical drawing of the pad layout for this package. The pin numbering convention starts with pin 1 in the upper left, as indicated in Figure 12, and increments
counter-clockwise around the package. Table 6 describes each pin function and Figure 13 illustrates typical case markings.
Figure 12. CX77105 Package Dimensional Drawing

Page 13
Package Dimensions and Pin Descriptions
Table 6. Pin Descriptions
| Pin # | Function | Pin # | Function | Pin # | Function |
| 1 | VREF | 5 | VCC1(1) | 9 | GND |
| 2 | VCONT | 6 | VCC2(1) | 10 | GND |
| 3 | GND | 7 | GND | GND PAD(2) | GND |
| 4 | RF IN | 8 | RF OUT | ||
| NOTE(S): (1) All supply pins may be connected together at the supply. (2) GROUND PAD is package underside. | |||||
Figure 13. Typical Case Markings

Page 14
Package and Handling Information
Package and Handling Information
Because of its sensitivity to moisture absorption, this device package is baked and vacuum packed prior to shipment. Instructions on the shipping container label must be followed regarding exposure to moisture after the container seal is broken, otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly.
The CX77105 is capable of withstanding an MSL 3/240 °C solder reflow. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. If the part is attached in a reflow oven, the temperature ramp rate should not exceed 5 °C per second; maximum temperature should not exceed 240 °C. If the part is manually attached, precaution should be taken to insure that the part is not subjected to temperatures exceeding 240 °C for more than 10 seconds. For details on both attachment techniques, precautions, and handling procedures recommended by Skyworks, please refer to Application Note: PCB Design and SMT
Assembly/Rework, Document Number 101752. Additional information on standard SMT reflow profiles can also be found in the JEDEC Standard J–STD–020B.
Production quantities of this product are shipped in the standard tape-and-reel format. For packaging details, refer to Application Note: Tape and Reel, Document Number 101568.
Page 15
Electrostatic Discharge Sensitivity
Electrostatic Discharge Sensitivity
The CX77105 is a Class I device. Figure 14 lists the Electrostatic Discharge (ESD) immunity level for each pin of the CX77105 product. The numbers in Figure 14 specify the ESD threshold level
for each pin where the I-V curve between the pin and ground starts to show degradation. The ESD testing was performed in compliance with MIL-STD-883E Method 3015.7 using the Human Body
Model. Since 2000 volts represents the maximum measurement limit of the test equipment used, pins marked > 2000 V pass 2000V ESD stress.
Figure 14. ESD Sensitivity Ares (Top View)

Various failure criteria can be utilized when performing ESD testing. Many vendors employ relaxed ESD failure standards which fail devices only after “the pin fails the electrical specification
limits” or “the pin becomes completely non-functional”. Skyworks employs most stringent criteria, fails devices as soon as the pin begins to show any degradation on a curve tracer.
To avoid ESD damage, both latent and visible, it is very important that the product assembly and test areas follow the Class-1 ESD handling precautions listed in Table 7.
Table 7. Precautions for GaAs ICs with ESD Thresholds Greater Than 200 V But Less Than 2000 V
| Personnel Grounding Wrist Straps Conductive Smocks, Gloves and Finger Cots Antistatic ID Badges | Facility Relative Humidity Control and Air Ionizers Dissipative Floors (less than 109 Ω to GND) |
| Protective Workstation Dissipative Table Tops Protective Test Equipment (Properly Grounded) Grounded Tip Soldering Irons Conductive Solder Suckers Static Sensors | Protective Packaging & Transportation Bags and Pouches (Faraday Shield) Protective Tote Boxes (Conductive Static Shielding) Protective Trays Grounded Carts Protective Work Order Holders |
Page 16
Ordering Information
| Model Number | Manufacturing Part Number | Product Revision | Package | Operating Temperature |
|---|---|---|---|---|
| CX77105 | CX77105-16P | 16 | 4x4LM-10 | –30 °C to +85 °C |
Revision History
| Revision | Level | Date | Description |
|---|---|---|---|
| A | December 10, 2002 | Initial Release |
References
Application Note: PCB Design and SMT Assembly/Rework, Document Number 101752.
Application Note: Tape and Reel, Document Number 101568
JEDEC Standard J–STD–020B.
© 2001, 2002, Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. ("Skyworks") products. These materials are provided by Skyworks as a service to its customers and may be used for informational purposes only. Skyworks assumes no responsibility for errors or omissions in these materials. Skyworks may make changes to its products, specifications and product descriptions at any time, without notice. Skyworks makes no commitment to update the information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from future changes to its products and product descriptions.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as may be provided in Skyworks' Terms and Conditions of Sale for such products, Skyworks assumes no liability whatsoever.
THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, RELATING TO SALE AND/OR USE OF SKYWORKS™ PRODUCTS INCLUDING WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. SKYWORKS FURTHER DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THESE
MATERIALS.
Skyworks™ products are not intended for use in medical, lifesaving or life-sustaining applications. Skyworks' customers using or selling Skyworks™ products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale.
The following are trademarks of Skyworks Solutions, Inc.: Skyworks™, the Skyworks symbol, and "Breakthrough Simplicity"™. Product names or services listed in this publication are for identification purposes only, and may be trademarks of third parties. Thirdparty brands and names are the property of their respective owners.
Additional information, posted at www.skyworksinc.com, is incorporated by reference.
Page 17

General Information: Skyworks Solutions, Inc. 4311 Jamboree Rd. Newport Beach, CA. 92660-3007 www.skyworksinc.com