CX65002 SKYWORKS

Document overview

  • PDF pages: 11

Technical content

Page 1

PDF page 1 diagram

DATA SHEET

CX65002: 700 – 1400 MHz Linear Power Amplifier Driver

Applications

  • AMPS/CDMA/TDMA/GSM handsets
  • Wireless Local Loop (WLL) and Industrial, Scientific, Medical (ISM) bands
  • Repeaters
  • Paging
  • Mobile radios
  • Telematics
  • UHF TV broadcasts

Features

  • 5 V single supply operation
  • Linear POUT of 24 dBm
  • OIP3 of 46 dBm
  • Excellent CDMA performance
  • Internal bias circuits
  • 8-pin SOIC 5.994 x 4.928 mm package with downset paddle
PDF page 1 diagram

RFIN

C1215

Figure 1. CX65002 Pinout – 8-Pin SOIC Package

(Top View)

Description

Skyworks CX65002 power amplifier driver offers a desirable combination of features that provide superb performance and ease of use in a low-cost Surface-Mounted Technology (SMT) package. The Gallium Arsenide (GaAs) Heterojunction Bipolar Transistor (HBT) power amplifier driver was developed and optimized for extreme linear performance in a variety of applications. It is ideal as a driver or output stage for transceivers and repeaters in AMPS/CDMA/TDMA/GSM paging base stations, mobile radios, telematics, and many other applications. The 8-pin Small Outline Integrated Circuit (SOIC) device package and pinout are shown in Figure 1. Figure 2 shows a functional

block diagram for the CX65002. Signal pin assignments and functional pin descriptions are provided in Table 1.

PDF page 1 diagram

VCC1

VCC2

VB

RFOUT

RFIN

C1216

Figure 2. CX65002 Functional Block Diagram

Page 2

Table 1. CX65002 Signal Descriptions

Pin # Name Description Pin # Name Description
1 NC No connection 5 VCC2 Supply voltage
2 VB Input bias for amplifier driver 6 RFOUT RF output
3 RFIN RF input 7 RFOUT RF output
4 Y Output of internal bias circuit 8 VCC1 Supply voltage

Table 2. CX65002 Absolute Maximum Ratings

Parameter Symbol Min Typical Max Units
RF input power PIN 10 dBm
Supply voltage (VCC1 and VCC2 pins) VCC 5.5 V
Supply current (ID + IBIAS) ICC 240 mA
Power dissipation 1.3 W
Case operating temperature TC –40 +85 °C
Storage temperature TST –55 +125 °C
Junction temperature TJ +150 °C

Note: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value.

Technical Description

The CX65002 is a single stage linear amplifier. The device can be externally matched for optimum gain and linearity using two to three passive components. These external components allow the amplifier to be set to a desired operating frequency. The CX65002 contains a bias circuit for optimum temperature tracking performance. An external resistor is used to set the bias current level. The value of this resistor can be selected to set the amplifier operational mode to Class A, B, or AB.

Package and Handling Information

Since the device package is sensitive to moisture absorption, it is baked and vacuum packed before shipping. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. If the part is attached in a reflow oven, the temperature ramp rate should not exceed 5 °C per second. Maximum temperature should not exceed 225 °C and the time spent at a temperature that exceeds 210 °C should be limited to less than 10 seconds. If the part is manually attached, precaution should be taken to

ensure that the part is not subjected to a temperature that exceeds 300 °C for more than 10 seconds.

Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. For packaging details, refer to the Skyworks Application Note, Tape and Reel, document number 101568.

Electrical and Mechanical Specifications

The absolute maximum ratings of the CX65002 are provided in Table 2. The recommended operating conditions are specified in Table 3 and electrical specifications are provided in Table 4. Typical performance characteristics of the CX65002 are shown in Figures 3 through 12. Figure 19 shows the package dimensions for the 8-pin SOIC and Figure 20 provides the tape and reel dimensions.

Electrostatic Discharge (ESD) Sensitivity

The CX65002 is a static-sensitive electronic device. Do not operate or store near strong electrostatic fields. Take proper ESD precautions.

Page 3

Table 3. CX65002 Recommended Operating Conditions

Parameter Symbol Min Typical Max Units
Supply voltage (VCC1 and VCC2 pins) VCC 5 V
Operating frequency FO 700 1400 MHz
Junction temperature TJ 140 °C
Maximum bias condition (VCC × ID) < (TJ_RECOMMENDED – TC)/RTH,J-C

Table 4. CX65002 Electrical Characteristics

(VCC = 5 V, TC = 25 °C)

Parameter Symbol Test Conditions Min Typical Max Units
OIP3 Match, Frequency = 900 MHz (Note 1)
Quiescent current (lD + lBIAS) Iq RBIAS = 270 Ω 120 130 mA
Small signal gain G PIN = –15 dBm 16.5 18 dB
Linear output power (Note 2) POUT PIN = +7 dBm 22.5 24 dBm
Power Added Efficiency PAE PIN = +7 dBm 34 38 %
Noise Figure (NF) NF 5 6 dB
Output IP3 OIP3 Two CW tones with 1 MHz spacing, PIN = –12 dBm per tone 40 44 dBm
Thermal resistance (junction – case) RTH,J-C 65 °C/W
ACPR Match, Frequency = 881.5 MHz (Note 3)
Quiescent current (lD + lBIAS) Iq RBIAS = 270 Ω 115 135 mA
Small signal gain G PIN = –15 dBm 15.5 17 dB
Peak envelope power (Note 2) PPEP IS95 downlink CDMA signal, 9 ch Fwd, PIN = 3 dBm 29 dBm
Average output power @ ACPR = –45 dBc, 885 kHz offset POUTACPR IS95 downlink CDMA signal, 9 ch Fwd, PIN = 4.5 dBm 19.5 21.5 dBm

Note 1: Device matched for optimum OIP3 according to circuit shown in Figure 15. Note 2: For reliable operation, do not violate the maximum input drive level specified in Table 2. Note 3: Device matched for optimum ACPR according to circuit shown in Figure 16.

PDF page 3 diagram

Figure 3. Typical POUT vs PIN @ 900 MHz Over Temperature (Circuit

Figure 4. Typical PAE vs PIN @ 900 MHz Over Temperature

Match for Optimum OIP3)

(Circuit Match for Optimum OIP3)

Page 4

PDF page 4 diagram

Figure 5. Typical Small Signal Gain From 700 to 850 MHz Over Temperature (Circuit Match for Optimum Gain)

PDF page 4 diagram

Figure 7. Typical Small Signal Gain From 1.1 to 1.4 GHz Over Temperature (Circuit Match for Optimum Gain)

PDF page 4 diagram

Figure 9. Typical NF From 850 to 960 MHz Over Temperature

(Circuit Match for Optimum OIP3)

PDF page 4 diagram

Figure 6. Typical Small Signal Gain From 850 to 960 MHz Over Temperature (Circuit Match for Optimum OIP3)

PDF page 4 diagram

Figure 8. Typical NF From 700 to 850 MHz Over Temperature

(Circuit Match for Optimum Gain)

PDF page 4 diagram

Figure 10. Typical NF From 1.1 to 1.4 GHz Over Temperature (Circuit Match for Optimum Gain)

Page 5

PDF page 5 diagram

Figure 11. Typical OIP3 vs Frequency Over Temperature (Circuit Match for Optimum OIP3)

Evaluation Board Description

Skyworks CX65002 Evaluation Board is used to test the performance of the CX65002 power amplifier driver. An Evaluation Board schematic diagram, optimized for the 3rd Order Output Intercept Point (OIP3), is shown in Figure 13. A schematic diagram optimized for Adjacent Channel Power Rejection (ACPR) is provided in Figure 14. The Evaluation Board assembly diagram is shown in Figure 15 and the Evaluation Board layer detail is shown in Figure 16. The mounting footprint for the CX65002 is shown in Figure 17.

Circuit Design Configurations The following design considerations are general in nature and must be followed regardless of final use or configuration. 1. Paths to ground should be made as short as possible. 2. The ground pad of the CX65002 power amplifier has special electrical and thermal grounding requirements. This pad is the main thermal conduit for heat dissipation. Since the circuit board acts as the heat sink, it must shunt as much heat as possible from the amplifier. As such, design the connection to the ground pad to dissipate the maximum wattage produced to the circuit board. Multiple vias to the grounding layer are required.

NOTE: Junction temperature (TJ) of the device increases with a poor connection to the slug and ground. This reduces the lifetime of the device.

  1. External bypass capacitors are required on the VCC line and on pins 4, 5, and 8.
PDF page 5 diagram

Figure 12. Typical ACPR vs POUT @ 881.5 MHz, 750 kHz Offset, 25 °C (Circuit Match for Optimum ACPR)

  1. Bias resistor R1 is used to control the reference voltage of the bias circuit (VCC1) at pin 8. 5. Inductor L2 is placed between the bias circuit output (pin 4) and the base of the RF transistor (pin 2) for bias circuit and RF transistor connection. Suggested matching circuits are shown in Figures 13 and 14.

Testing Procedure Use the following procedure to set up the CX65002 Evaluation Board for testing. Refer to Figure 18 for guidance: 1. Connect a 5.0 V supply to VCC. If available, enable the current limiting function of the power supply to 240 mA. 2. Connect a signal generator to the RF signal input port. Set it to the desired RF frequency at a power level of –15 dBm or less to the Evaluation Board but do NOT enable the RF signal. 3. Connect a spectrum analyzer to the RF signal output port. 4. Enable the power supply. 5. Enable the RF signal. 6. Take measurements.

CAUTION: If any of the input signals exceed the rated maximum values, the CX65002 Evaluation Board can be permanently damaged.

Page 6

Power Supply

PDF page 6 diagram

Figure 13. Application Schematic Optimized for OIP3 @ 900 MHz

Power Supply

PDF page 6 diagram

Figure 14. Application Schematic Optimized for ACPR @ 881.5 MHz

Page 7

J3

JP1 C7 R1 C5 L1 C8 R2 C10
C9 L3 C1 C2 L2 C4 C6

J1 (RF In)

J2 (RF Out)

C1434

Figure 15. Evaluation Board Assembly Diagram

Page 8

PDF page 8 diagram

Layer 1: Top Metal

PDF page 8 diagram

Layer 4: Ground

C1440

Figure 16. Evaluation Board Layer Detail

Page 9

PDF page 9 diagram

Dimensions are in millimeters

C1218

Figure 17. PCB Mounting Footprint

PDF page 9 diagram

C1240f

Figure 18. CX65002 Evaluation Board Testing Configuration

Page 10

PDF page 10 diagram

2.464 ± .051

PDF page 10 diagram

Top View

Bottom View

PDF page 10 diagram

o

PDF page 10 diagram

1.473 ± .076

Side View

End View

PDF page 10 diagram

Gauge Plane Seating Plane

Detail A

All measurements are in millimeters

C1444

Figure 19. CX65002 8-Pin SOIC Package Dimensions

PDF page 10 diagram

A

B

  1. Carrier tape: black conductive polycarbonate or polystyrene. 2. Cover tape material: transparent conductive PSA. 3. Cover tape size: 9.3 mm wide. 4. All measurements are in millimeters.

C1242

Figure 20. CX65002 8-Pin SOIC Tape and Reel Dimensions

Page 11

Ordering Information

Model Name Manufacturing Part Number Evaluation Kit Part Number
CX65002 700-1400 MHz Linear Power Amplifier Driver CX65002-12 TW10-D252 (tuned for optimum OIP3 @ 900 MHz ) TW10-D253 (tuned for optimum ACPR @ 881.5 MHz)

Copyright © 2003, 2004, Skyworks Solutions, Inc. All Rights Reserved.

Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products. These materials are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials. Skyworks may make changes to its documentation, products, specifications and product descriptions at any time, without notice. Skyworks makes no commitment to update the information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from future changes to its documentation, products, specifications and product descriptions.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by or under this document. Except as may be provided in Skyworks Terms and Conditions of Sale for such products, Skyworks assumes no liability whatsoever in association with its documentation, products, specifications and product descriptions.

THESE MATERIALS ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED OR OTHERWISE, RELATING TO SALE AND/OR USE OF SKYWORKS PRODUCTS INCLUDING WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. SKYWORKS FURTHER DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THESE MATERIALS WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGE.

Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale.

The following are trademarks of Skyworks Solutions, Inc.: Skyworks™, the Skyworks logo, and Breakthrough Simplicity™. Product names or services listed in this publication are for identification purposes only, and may be trademarks of Skyworks or other third parties. Third-party brands and names are the property of their respective owners. Additional information, posted at www.skyworksinc.com, is incorporated by reference.