DATASHEET SEARCH SITE

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 19

Technical content

  1. General description The CBTL06GP213 is a six-channel (‘hex’) multiplexer for DisplayPort, HDMI and PCI Express applications at Generation 2 (‘Gen2’) speeds. It provides four differential channels capable of 1 : 2 switching or 2 : 1 multiplexing bidirectional, AC-coupled PCI Express, DisplayPort signals, USB3 SuperSpeed or DC coupled TMDS signals, using high-bandwidth pass-gate technology. It provides support for high common-mode/bias voltage on the high-speed differential channels. Additionally, it provides for switching/multiplexing of the Hot Plug Detect signal as well as the AUX or DDC (Display Data Channel) signals, for a total of six channels on the display side. The AUX and DDC channels provide a four-position multiplexer such that an additional level of multiplexing can be accomplished when AUX and DDC I/Os are on separate pins of the display source device. The CBTL06GP213 is designed for Gen2 speeds, supporting 5.0 Gbit/s for PCI Express, 5.4 Gbit/s for DisplayPort or 6 Gbit/s for HDMI 2.0. It consumes 490 A current (typical) in operational mode and provides a shutdown function to support battery-powered applications. A typical application of CBTL06GP213 is on applications where one of two GPU display sources must be selected to connect to a display sink device or connector. A controller chip selects which path to use by setting a select signal HIGH or LOW. Due to the non-directional nature of the signal paths (which use high-bandwidth pass gate technology), the CBTL06GP213 can also be used in the reverse topology, for example, to connect one display source device to one of two display sink devices or connectors. 2. Features and benefits  1 : 2 switching or 2 : 1 multiplexing of DisplayPort (v1.2 - 5.4 Gbit/s) PCI Express (v2.0 - 5.0 Gbit/s) signals, USB3 SuperSpeed or HDMI 2.0 (6 Gbit/s) TMDS signals  4 high-speed differential channels with 2 : 1 muxing/switching for DisplayPort or PCI Express or HDMI signals  1 channel with 4 : 1 or 4 : 2 muxing/switching for AUX at 1 Mbit/s or DDC signals, USB2 signals  1 channel with 2 : 1 muxing/switching for single-ended HPD signal  High-bandwidth analog pass-gate technology  Supports high-speed signal switching over a wide common-mode range and differential swing  R ON on DP high-speed channels: 7  CBTL06GP213 Second-generation high performance general purpose switch Rev. 3.1 — 13 December 2016 Product data sheet

[1] Industrial temperature range. [2] Total height including solder balls af ter printed circuit board mounting = 1.15 mm. www.nxp.com/products/related/package-markings.html. Table 1. Ordering information

4.1 Ordering options

Table 2. Ordering options

3000 T amb = 40 C to +105 C

Product data sheet Rev. 3.1 — 13 December 2016 4 of 19 NXP Semiconductors CBTL06GP213 Second-generation high performance general purpose switch 6. Pinning information

6.1 Pinning

Fig 2. Pin configuration for TFBGA50 Transparent top view Fig 3. Ball mapping 002aah659 Transparent top view CBTL06GP213EE H J G F E D C A B 2468 91357 ball A1 index area A 002aah660 GPU_SEL VDD DIN1_0− DIN1_1− DIN1_2− DIN1_3+ DIN1_3− 23 456 789 B DOUT_0− DOUT_0+ GND DIN1_0+ DIN1_1+ DIN1_2+ XSD DIN2_0+ DIN2_0− C DDC_AUX _SEL GND D DOUT_1− DOUT_1+ DIN2_1+ DIN2_1− E DOUT_2− DOUT_2+ DIN2_2+ DIN2_2− F DOUT_3− DOUT_3+ DIN2_3+ DIN2_3− G GND GND H AUX− AUX+ HPD_2 GND DDC_CLK2 DAUX2+ GND DDC_CLK1 DAUX1+ J HPDIN HPD_1 VDD DDC_DAT2 DAUX2− DDC_DAT1 DAUX1−DDC_CLK DDC_DAT

6.2 Pin description

Table 3. Pin description path 2 left-side is connected to its corresponding right-side I/O. right-side I/O. Refer to Table 6 for switch connection details. Tri-level select pin. Selects between DDC and AUX paths. DAUX1+ H9 differential I/O High-speed differential pair for AUX signals, path 1, left-side.

Refer to Figure 1 “Functional diagram”. signal is needed for the multiplexer to function. The switch position for the main channels is selected using the select signal GPU_SEL. DDC / AUX channel. The detailed operation is described in Section 7.1.

7.1 Multiplexer/switc h select functions

DDC_AUX_SEL as described below. DAUX2+ H6 differential I/O High-speed differential pair for AUX signals, path 2, left-side. HPD_1 J2 single-ended I/O Single ended channel for the HPD signal, path 1, left-side. HPD_2 H3 single-ended I/O Single ended channel for the HPD signal, path 2, left-side. HPDIN J1 single-ended I/O Single ended channel for the HPD signal, right-side. VDD A2, J4 power supply 3.3 V power supply. Table 3. Pin description …continued Table 4. Multiplexer/switch select control for DIN and DOUT channels Table 5. Multiplexer/switch sele ct control for HPD channel

7.2 Shutdown function

current consumption to near-zero. Table 6. Multiplexer/switch select control for DDC and AUX channels Table 7. Shutdown function

Technology Association, Arlington, VA, USA.

  1. Recommended operating conditions

10.1 General characteristics

Table 8. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Table 9. Recommended operating conditions Table 10. General characteristics

10.2 DisplayPort channel characteristics

with Common-mode voltage of 3 V. Table 11. DisplayPort channel characteristics

10.3 AUX and DDC ports

[1] Time from DDC/AUX input changing state to AUX output changing state. Includes DDC/AUX rise/fall time. and 50  single-ended impedance reference. Table 12. AUX and DDC port characteristics

10.4 HPDIN input , HPD_x outputs

[1] Time from HPDIN changing state to HPD_x changing state. Includes HPD rise/fall time.

10.5 GPU_SEL, DDC_AUX_SEL, XSD inputs

Table 13. HPD input and output characteristics Table 14. GPU_SEL, DDC_AUX_SEL, XSD input characteristics

Product data sheet Rev. 3.1 — 13 December 2016 12 of 19 NXP Semiconductors CBTL06GP213 Second-generation high performance general purpose switch 11. Package outline Fig 5. Package outline TFBGA50 (SOT1345-1) 5HIHUHQFHV2XWOLQH YHUVLRQ (XURSHDQ SURMHFWLRQ ,VVXHGDWH ,(& -('(& -(,7$ 627 02 VRWBSR 8QLW PP PD[ QRP PLQ 'LPHQVLRQV PPDUHWKHRULJLQDOGLPHQVLRQV 7)%*$ SODVWLFWKLQILQHSLWFKEDOOJULGDUUD\\SDFNDJH EDOOV $ $ E'(HH H Y Z 627 PP VFDOH GHWDLO; EDOO$ LQGH[DUHD EDOO$ LQGH[DUHD H H $ &%‘Y &‘ZE &\\ \\ H H

Product data sheet Rev. 3.1 — 13 December 2016 13 of 19 NXP Semiconductors CBTL06GP213 Second-generation high performance general purpose switch 12. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 “Surface mount reflow soldering description”.

12.1 Introduction to soldering

Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization.

12.2 Wave and reflow soldering

Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following:

  • Through-hole components
  • Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are:
  • Board specifications, including the board finish, solder masks and vias
  • Package footprints, including solder thieves and orientation
  • The moisture sensitivity level of the packages
  • Package placement
  • Inspection and repair
  • Lead-free soldering versus SnPb soldering

12.3 Wave soldering

Key characteristics in wave soldering are:

  • Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave
  • Solder bath specifications, including temperature and impurities

12.4 Reflow soldering

  • Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 6) than a SnPb process, thus reducing the process window
  • Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board
  • Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 15 and 16 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 6.

Table 15. SnPb eutectic process (from J-STD-020D) Table 16. Lead-free process (from J-STD-020D)

“Surface mount reflow soldering description”. Table 17. Abbreviations

Table 18. Revision history

Product data sheet Rev. 3.1 — 13 December 2016 17 of 19 NXP Semiconductors CBTL06GP213 Second-generation high performance general purpose switch 15. Legal information

15.1 Data sheet status

[1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.

15.2 Definitions

Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet.

15.3 Disclaimers

Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification.

Product data sheet Rev. 3.1 — 13 December 2016 18 of 19 NXP Semiconductors CBTL06GP213 Second-generation high performance general purpose switch Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications. Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions.

15.4 Licenses

15.5 Trademarks

Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 16. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Purchase of NXP ICs with HDMI technology Use of an NXP IC with HDMI technology in equipment that complies with the HDMI standard requires a license from HDMI Licensing LLC, 1060 E. Arques Avenue Suite 100, Sunnyvale CA 94085, USA, e-mail: admin@hdmi.org

NXP Semiconductors CBTL06GP213 Second-generation high performance general purpose switch © NXP Semiconductors N.V. 2016. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 13 December 2016 Document identifier: CBTL06GP213 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. 17. Contents

10.5 GPU_SEL, DDC_AUX_SEL, XSD

inputs . . . . 11