DATASHEET SEARCH SITE
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 21
Technical content
- General description The CBTL05024 is a multiplexer/demultiplexer switch chip optimized to interface the Thunderbolt/MiniDP connector with Thunderbolt systems. It supports 10.3125 Gbit/s Thunderbolt or DisplayPort v1.2 channels. The TB MUX is a 3 : 1 switch that selects between Thunderbolt data path and DisplayPort v1.2 side-band signals — either DDC or AUX. The DP MUX is a 2 : 1 switch that selects between DP ML (DisplayPort Main Link) and LS TX/RX signals. Both LSTX and LSRX are the side-band signals for Thunderbolt channel. This chip also includes HPD and CA_DET buffers for HPD_IN and CA_DET control signals. CBTL05024 is powered by a 3.3 V supply and it is available in a 3 mm 3 mm HVQFN24 package with 0.4 mm pitch. 2. Features and benefits
2.1 TB MUX 3 : 1 switch
This 3 : 1 switch is implemented by two cascaded 2 : 1 switches The first 2 : 1 10G MUX is controlled by TB_ENA, AUXIO_EN and DP_PD pins The second 2 : 1 AUX MUX is controlled by CA_DET signal multiplexing of the
720 Mbit/s Differential FAUX (or 1 Mbit/s AUX) and DDC (Direct Display Control)
When CA_DET is HIGH, DDC path is selected Differential TB channel Low insertion loss: 1.3 dB at 5 GHz Low return loss: < 20 dB at 5 GHz Low ON-state resistance: 8 Bandwidth: 10 GHz Low off-state isolation: 20 dB at 5 GHz Low crosstalk: 36 dB at 5 GHz Differential input voltage VID: 1.2 V (maximum) Differential AUX channel Low insertion loss: 1.1 dB at 5 MHz; 1.8 dB at 360 MHz Low return loss: 18 dB at 5 MHz; 16 dB at 360 MHz CBTL05024 High performance multiplexer/demultiplexer switch for Thunderbolt applications Rev. 4 — 27 March 2014 Product data sheet
Product data sheet Rev. 4 — 27 March 2014 2 of 21 NXP Semiconductors CBTL05024 High performance MUX/deMUX switch for Thunderbolt applications Low ON-state resistance: 13 (typical); 16 (maximum) Bandwidth: 3 GHz Low off-state isolation: 80 dB at 5 MHz; 55 dB at 360 MHz Low crosstalk: 26 dB at 2.7 GHz Common-mode input voltage VIC: 0 V to 3.3 V Differential input voltage VID: 1.4 V (maximum) DDC channel ON-state resistor: 50 (maximum) 100 kHz 3.3 V voltage swing signal Both AUXIO+ and AUXIO outputs have 85 k (20 %) resistors The 85 k AUXIO pull-up resistor The 85 k AUXIO+ pull-down resistor is always present
2.2 DP MUX 2 : 1 switch
Multiplexes between differential DP ML signal and LSTX/LSRX signals The DP ML (DisplayPort Main Link) runs up to HBR2 data rate of 5.4 Gbit/s The low speed DC-coupled signals LSTX and LSRX are 3.3 V single-ended signals that operate at 1 Mbit/s 5.4 Gbit/s DP-DPMLO path for DP MUX Low insertion loss for DP-DPMLO path: 1.2 dB at 2.7 GHz Low return loss for DP-DPMLO path: 15 dB at 2.7 GHz Low ON-state resistance for DP-DPMLO path: 9 High bandwidth: 5.5 GHz Low off-state isolation: 20 dB at 2.7 GHz Low crosstalk: 25 dB at 2.7 GHz Common-mode input voltage VIC: 0 V to 3.3 V Differential input voltage VID: 1.4 V (maximum) LS-DPMLO path for DP MUX Low insertion loss: single-ended insertion loss (ON) is 1.0 dB at 5 MHz Low return loss: single-ended return loss (ON) is 20 dB at 5 MHz Low ON-state resistance: 16 (typical) for VDD =3 . 3V High bandwidth: Single-ended 3 dB bandwidth is 1 GHz Low off-state isolation: single-ended insertion loss (OFF) is 60 dB at 5 MHz Low crosstalk: 40 dB at 5 GHz
2.3 General
The input of the HPD (Hot Plug Detect) buffer is 5 V tolerant HPDOUT and CA_DETOUT buffers CA_DET input leakage current < 0.1 A to prevent driving the 1 M pull-down to a HIGH level Integrated LSRX buffer with 1 M pull-down resistor (R1) on the LSRX buffer input Integrated 8.75 k pull-up resistor (R4) on the LSTX pin
[1] Maximum package height is 1 mm.
3.1 Ordering options
Table 1. Ordering information Table 2. Ordering options
6000 T amb = 20 Ct o+ 8 5C
Product data sheet Rev. 4 — 27 March 2014 4 of 21 NXP Semiconductors CBTL05024 High performance MUX/deMUX switch for Thunderbolt applications 4. Block diagram Fig 1. Block diagram of CBTL05024 002aag997 CONTROL LOGIC TB_ENA AUXIO_EN AUXIO− AUXIO+ AUX MUX 2 : 1 85 kΩ AUX− AUX+ DDC_DAT DDC_CLK CA_DETCA_DETOUT HPDHPDOUT DP MUX 2 : 1 DP+ DP− LSTX LSRX
3.3 V DPMLO+
DPMLO− DP_PD CBTL05024 3.3 V 85 kΩ 10G MUX 2 : 1 8.75 kΩ TB− TB+ LSRX buffer R1 1 MΩ
Product data sheet Rev. 4 — 27 March 2014 5 of 21 NXP Semiconductors CBTL05024 High performance MUX/deMUX switch for Thunderbolt applications 5. Pinning information
5.1 Pinning
(1) Center pad is connected to PCB GND pl ane for electrical grounding and thermal relief. Refer to Section 10 for package-related information. Fig 2. Pin configuration 002aag998 Transparent top view TB_ENA HPD
24 AUXIO_EN
23 AUXIO−
22 AUXIO+
20 DPMLO−
19 DPMLO+
18 CA_DET
21 GND
CA_DETOUT16 AUX− VDD 4DDC_DAT 5DDC_CLK
2 AUX+
DP_PD 6 TB− 7 TB+ 8 DP− 10 DP+ 11 HPDOUT 12 GND 9 GND(1)
5.2 Pin description
Table 3. Pin description AUXIO 23 differential I/O Differential signals for TB MUX. DPMLO 20 differential I/O Differential signals for DP MUX. LSRX 13 single-ended output Single-ended TB low speed receive signal. LSTX 14 single-ended I/O Single-ended TB low speed transmit signal. HPDOUT 12 CMOS output Output buffer for HPD. HPD 17 CMOS input HPD input with 5 V tolerance. CA_DETOUT 16 CMOS output 3.3 V CMOS output buffer for CA_DET. AUXIO_EN 24 CMOS input The control signal for TB MUX.
3.3 V supply option
GND 9, 21 Ground Supply ground (0 V). for both electrical grounding and thermal relief.
Refer to Figure 1 “Block diagram of CBTL05024”.
6.1 Buffer function tables
6.2 AUX MUX function table
6.3 Operation modes of both DPML MUX and TB MUX
[1] HPD must be LOW during Test mode. Table 4. HPD buffer Table 5. CA_DET buffer Table 6. 2 : 1 AUX MUX function
1 DDC
Table 7. Operation modes
0 X 0 X 3-state 3-state DP Standby mode ON ON
0 X 1 X 3-state LS Standby mode ON ON
[1] All voltage values, except differential volt ages, are with respect to network ground terminal. Technology Association, Arlington, VA, USA.
- Recommended operating conditions
DPMLO+/ must work. The initial Ron of DP MUX in Table 14 should be < 50 . Table 8. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Table 9. Operating conditions
9.1 Device general characteristics
[1] Do not include current through R4. [2] Outputs are undefined during reconfiguration, incl uding enable and disable time of the multiplexers. Table 10. General characteristics Table 11. TB channel of 2 : 1 10G MUX dynamic and static characteristics
Table 11. TB channel of 2 : 1 10G MUX dynamic and static characteristics …continued Table 12. AUX - AUXIO channel of AUX MUX dynamic and static characteristics
9.3 DP MUX channel characteristics
Table 13. DDC - AUXIO channel of AUX MUX dynamic and static characteristics Table 14. Channel dynamic and static characteristics
9.4 Control signals characteristics
[1] The leakage current on CA_DET pin must not drive the 1 M pull-down to a HIGH level. Table 14. Channel dynamic and static characteristics …continued Table 15. CA_DET input buffer characteristics Table 16. HPD input buffer characteristics Table 17. TB_ENA, DP_PD or AUXIO_EN input characteristics Table 18. CA_DETOUT and HPDOUT output buffer characteristics
9.5 Integrated LSRX buffer characteristics
9.6 Bias resistor characteristics
Table 19. LSRX buffer characteristics Table 20. Characteristics of AUXIO+ pin in DP/DP++ mode Table 21. Characteristics of AUXIO pin in DP/DP++ mode Table 22. Characteristics of DPMLO pin in TB mode Table 23. Characteristics of LSTX pin
Product data sheet Rev. 4 — 27 March 2014 14 of 21 NXP Semiconductors CBTL05024 High performance MUX/deMUX switch for Thunderbolt applications 10. Package outline Fig 3. Package outline SOT905-1 (HVQFN24) 5()(5(1&(6287/,1( 9(56,21 (8523($1 ,(& -('(& -(,7$ 627 1RWH 3ODVWLFRUPHWDOSURWUXVLRQVRIPPPD[LPXPSHUVLGHDUHQRWLQFOXGHG 81,7 $ PD[ PP ',0(16,216 PPDUHWKHRULJLQDOGLPHQVLRQV +94)1 SODVWLFWKHUPDOHQKDQFHGYHU\\WKLQTXDGIODWSDFNDJH QROHDGV WHUPLQDOV ERG\\[[PP PP VFDOH E E F ' (K H H H Y Z 627 \\&\\ WHUPLQDO LQGH[DUHD % $' GHWDLO; F H H E H H $&%Y 0 &Z 0 WHUPLQDO LQGH[DUHD E E 'K /
Product data sheet Rev. 4 — 27 March 2014 15 of 21 NXP Semiconductors CBTL05024 High performance MUX/deMUX switch for Thunderbolt applications 11. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 “Surface mount reflow soldering description”.
11.1 Introduction to soldering
Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization.
11.2 Wave and reflow soldering
Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following:
- Through-hole components
- Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are:
- Board specifications, including the board finish, solder masks and vias
- Package footprints, including solder thieves and orientation
- The moisture sensitivity level of the packages
- Package placement
- Inspection and repair
- Lead-free soldering versus SnPb soldering
11.3 Wave soldering
Key characteristics in wave soldering are:
- Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave
- Solder bath specifications, including temperature and impurities
11.4 Reflow soldering
- Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 4) than a SnPb process, thus reducing the process window
- Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board
- Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 24 and 25 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 4.
Table 24. SnPb eutectic process (from J-STD-020D) Table 25. Lead-free process (from J-STD-020D)
“Surface mount reflow soldering description”. Table 26. Abbreviations
Table 27. Revision history
Product data sheet Rev. 4 — 27 March 2014 19 of 21 NXP Semiconductors CBTL05024 High performance MUX/deMUX switch for Thunderbolt applications 14. Legal information
14.1 Data sheet status
[1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.
14.2 Definitions
Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet.
14.3 Disclaimers
Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification.
Product data sheet Rev. 4 — 27 March 2014 20 of 21 NXP Semiconductors CBTL05024 High performance MUX/deMUX switch for Thunderbolt applications Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications. Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions.
14.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 15. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com
NXP Semiconductors CBTL05024 High performance MUX/deMUX switch for Thunderbolt applications © NXP Semiconductors N.V. 2014. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 27 March 2014 Document identifier: CBTL05024 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. 16. Contents