BUK207-50Y PHILIPS
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 13
Technical content
Philips Semiconductors Product specification TOPFET high side switch BUK207-50Y SMD version of BUK203-50Y DESCRIPTION QUICK REFERENCE DATA Monolithic temperature and SYMBOL PARAMETER MIN. UNIT overload protected power switch based on MOSFET technology in a I L Nominal load current (ISO) 1.6 A 5 pin plastic surface mount envelope, configured as a single high side switch. SYMBOL PARAMETER MAX. UNIT APPLICATIONS VBG Continuous off-state supply voltage 50 V IL Continuous load current 4 A General controller for driving T j Continuous junction temperature 150 ˚C lamps, motors, solenoids, heaters. RON On-state resistance 220 m Ω FEATURES FUNCTIONAL BLOCK DIAGRAM Vertical power DMOS switch Low on-state resistance
5 V logic compatible input
Overtemperature protection - self resets with hysteresis Overload protection against short circuit load with output current limiting; latched - reset by input High supply voltage load protection Supply undervoltage lock out Status indication for overload protection activated Diagnostic status indication of open circuit load Very low quiescent current Voltage clamping for turn off of inductive loads ESD protection on all pins Reverse battery and overvoltage protection Fig.1. Elements of the TOPFET HSS with internal ground resistor. PINNING - SOT426 PIN CONFIGURATION SYMBOL PIN DESCRIPTION
1 G round
2 Input
3 (connected to mb)
4 Status
5 Load
Fig. 2. Fig. 3. mb B attery BATT LOAD INPUT GROUND STATUS POWER MOSFET RG CONTROL & PROTECTION CIRCUITS mb 12 45 B G L I S HSS TOPFET July 1996 1 Rev 1.000
Philips Semiconductors Product specification TOPFET high side switch BUK207-50Y SMD version of BUK203-50Y LIMITING VALUES Limiting values in accordance with the Absolute Maximum System (IEC 134) SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT Battery voltages VBG Continuous off-state supply voltage - 0 50 V Reverse battery voltages1 External resistors: -VBG Repetitive peak supply voltage R I = RS ≥ 4.7 kΩ , δ ≤ 0.1 - 32 V -VBG Continuous reverse supply voltage RI = RS ≥ 4.7 kΩ -1 6V IL Continuous load current T mb ≤ 110 ˚C - 4 A PD Total power dissipation T mb ≤ 25 ˚C - 50 W Tstg Storage temperature - -55 175 ˚C Tj Continuous junction temperature2 - - 150 ˚C Tsold Lead temperature during soldering - 250 ˚C Input and status I I Continuous input current - -5 5 mA IS Continuous status current - -5 5 mA II Repetitive peak input current δ ≤ 0.1 -20 20 mA IS Repetitive peak status current δ ≤ 0.1 -20 20 mA Inductive load clamping EBL Non-repetitive clamping energy T mb = 150 ˚C prior to turn-off - 1.4 J ESD LIMITING VALUE SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT VC Electrostatic discharge capacitor Human body model; - 2 kV voltage C = 250 pF; R = 1.5 k Ω THERMAL CHARACTERISTIC SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Thermal resistance3 R th j-mb Junction to mounting base - - 2 2.5 K/W 1 Reverse battery voltage is allowed only with external input and status resistors to limit the currents to a safe value. 2 For normal continuous operation. A higher Tj is allowed as an overload condition but at the threshold Tj(TO) the over temperature trip operates to protect the switch. 3 Of the output Power MOS transistor. July 1996 2 Rev 1.000
Philips Semiconductors Product specification TOPFET high side switch BUK207-50Y SMD version of BUK203-50Y STATIC CHARACTERISTICS Tmb = 25 ˚C unless otherwise stated SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Clamping voltages VBG Battery to ground I G = 1 mA 50 55 65 V VBL Battery to load I L = IG = 1 mA 50 55 65 V -VLG Negative load to ground I L = 1 mA 12 17 21 V Supply voltage battery to ground VBG Operating range1 -5 - 4 0 V Currents VBG = 13 V IL Nominal load current2 VBL = 0.5 V; Tmb = 85 ˚C 1.6 - - A IB Quiescent current3 VIG = 0 V; VLG = 0 V - 0.1 2 µA IG Operating current4 VIG = 5 V; IL = 0 A 1.5 2.2 4 mA IL Off-state load current5 VBL = 13 V; VIG = 0 V - 0.1 1 µA Resistances R ON On-state resistance6 VBG = 13 V; IL = 2 A; tp = 300 µs - 160 220 m Ω R ON On-state resistance V BG = 5 V; IL = 0.5 A; tp = 300 µs - 225 320 m Ω R G Internal ground resistance IG = 10 mA - 150 - Ω INPUT CHARACTERISTICS Tmb = 25 ˚C; VBG = 13 V SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT II Input current V IG = 5 V 35 60 100 µA VIG Input clamping voltage I I = 200 µA 6 7.5 8.5 V VIG(ON) Input turn-on threshold voltage - 2.1 2.7 V VIG(OFF) Input turn-off threshold voltage 1.5 2 - V 1 On-state resistance is increased if the supply voltage is less than 9 V. Refer to figure 8. 2 Defined as in ISO 10483-1. 3 This is the continuous current drawn from the battery when the input is low and includes leakage current to the load. 4 This is the continuous current drawn from the battery with no load connected, but with the input high. 5 The measured current is in the load pin only. 6 The supply and input voltage for the RON tests are continuous. The specified pulse duration tp refers only to the applied load current. July 1996 3 Rev 1.000
Philips Semiconductors Product specification TOPFET high side switch BUK207-50Y SMD version of BUK203-50Y PROTECTION FUNCTIONS AND STATUS INDICATIONS Truth table for normal, open-circuit load and overload conditions and abnormal supply voltages. FUNCTIONS TRUTH TABLE THRESHOLD SYMBOL CONDITION INPUT STATUS OUTPUT MIN. TYP. MAX. UNIT Normal on-state 1 1 1 Normal off-state 0 1 0 IL(OC) Open circuit load1 1 0 1 30 90 150 mA Open circuit load 0 1 0 Tj(TO) Over temperature2 1 0 0 150 175 - ˚C Over temperature3 00 0 VBL(TO) Short circuit load4 1 0 0 9 10.5 12 V Short circuit load 0 1 0 VBG(TO) Low supply voltage5 X1 0 3 4 5 V VBG(LP) High supply voltage6 X1 0 4 0 4 5 5 0 V For input ‘0’ equals low, ‘1’ equals high, ‘X’ equals don’t care. For status ‘0’ equals low, ‘1’ equals open or high. For output switch ‘0’ equals off, ‘1’ equals on. STATUS CHARACTERISTICS Tmb = 25 ˚C. The status output is an open drain transistor, and requires an external pull-up circuit to indicate a logic high. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT VSG Status clamping voltage I S = 100 µA; VIG = 0 V 6 7 8 V VSG Status low voltage I S = 50 µA; VBG = 13 V; VIG = 5 V - 0.7 0.8 V IS Status leakage current V SG = 5 V - 0.1 1 µA IS Status saturation current7 VSS = 5 V; RS = 0 Ω ; VBG = 13 V - 5 - mA
Application information
R S External pull-up resistor8 VSS = 5 V - 100 - k Ω 1 In the on-state, the switch detects whether the load current is less than the quoted open load threshold current. This is for status indication only. Typical hysteresis equals 25 mA. The thresholds are specified for supply voltage within the normal working range. 2 After cooling below the reset temperature the switch will resume normal operation. The reset temperature is lower than the trip temperature by typically 10 ˚C. 3 If the overtemperature protection has operated, status remains low to indicate the overtemperature condition even if the input is taken low, providing the device has not cooled below the reset temperature. 4 After short circuit protection has operated, the input voltage must be toggled low for the switch to resume normal operation. 5 Undervoltage sensor causes the device to switch off. Typical hysteresis equals 0.7 V. 6 Overvoltage sensor causes the device to switch off to protect the load. Typical hysteresis equals 1.3 V. 7 In a fault condition with the pull-up resistor short circuited while the status transistor is conducting. 8 The pull-up resistor also protects the status pin during reverse battery conditions. July 1996 4 Rev 1.000
Philips Semiconductors Product specification TOPFET high side switch BUK207-50Y SMD version of BUK203-50Y DYNAMIC CHARACTERISTICS Tmb = 25 ˚C; VBG = 13 V SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Inductive load turn-off -VLG Negative load voltage1 VIG = 0 V; IL = 2 A; tp = 300 µs1 5 2 0 2 5 V Short circuit load protection2 VIG = 5 V; RL ≤ 10 mΩ td sc Response time - 75 - µs IL Load current prior to turn-off t < td sc -1 7- A Overload protection3 IL(lim) Load current limiting V BL = 9 V; tp = 300 µs1 2 1 5 2 2 A SWITCHING CHARACTERISTICS Tmb = 25 ˚C, VBG = 13 V, for resistive load RL = 13 Ω . SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT During turn-on to VIG = 5 V td on Delay time to 10% V L -1 6- µs dV/dton Rate of rise of load voltage - 1.3 3 V/ µs t on Total switching time to 90% V L -4 0- µs During turn-off to VIG = 0 V td off Delay time to 90% V L -2 0- µs dV/dtoff Rate of fall of load voltage - 1.6 3 V/ µs t off Total switching time to 10% V L -3 5- µs CAPACITANCES Tmb = 25 ˚C; f = 1 MHz; VIG = 0 V SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT C ig Input capacitance V BG = 13 V - 15 20 pF C bl Output capacitance V BL = VBG = 13 V - 120 170 pF C sg Status capacitance V SG = 5 V - 11 15 pF 1 For a high side switch, the load pin voltage goes negative with respect to ground during the turn-off of an inductive load. This negative voltage is clamped by the device. 2 The load current is self-limited during the response time for short circuit load protection. Response time is measured from when input goes high. 3 If the load resistance is low, but not a complete short circuit, such that the on-state voltage remains less than VBL(TO), the device remains in current limiting until the overtemperature protection operates. July 1996 5 Rev 1.000
Philips Semiconductors Product specification TOPFET high side switch BUK207-50Y SMD version of BUK203-50Y Fig.4. High side switch measurements schematic. (current and voltage conventions) Fig.5. Normalised limiting power dissipation. PD % = 100⋅PD /PD (25 ˚C) = f(Tmb ) Fig.6. Limiting continuous on-state load current. IL = f(Tmb ); conditions: VIG = 5 V, VBG = 13 V Fig.7. Typical on-state characteristics, Tj = 25 ˚C. IL = f(VBL); parameter VBG ; tp = 250 µs Fig.8. Typical on-state resistance, Tj = 25 ˚C. R ON = f(VBG ); conditions: IL = 2 A; tp = 300 µs Fig.9. Typical on-state resistance, tp = 300 µs. R ON = f(Tj); parameter VBG ; condition IL = 0.5 A L I S TOPFET HSS B G IB IG II IS IL VBG VIG VSG RS VLG LOAD VBL 0 1 2 VBL / V IL / A BUK207-50Y10 1.50.5 VBG / V = 13 0 20 40 60 80 100 120 140 Tmb / C PD% Normalised Power Derating120 110 100 1 10 100 VBG / V RON / Ohm BUK207-50Y400 300 200 100 0 20 40 60 80 100 120 140 Tmb / C IL / A BUK207-50Y8 -60 -20 20 60 100 140 180 Tj / C RON / Ohm BUK207-50Y0.5 0.4 0.3 0.2 0.1 5 V 13 V VBG = typ. July 1996 6 Rev 1.000
Philips Semiconductors Product specification TOPFET high side switch BUK207-50Y SMD version of BUK203-50Y Fig.10. Typical supply characteristics, 25 ˚C. IG = f(VBG ); parameter VIG Fig.11. Typical operating supply current. IG = f(Tj); parameter VBG ; condition VIG = 5 V Fig.12. Typical supply quiescent current. IB = f(Tj); condition VBG = 13 V, VIG = 0 V, VLG = 0 V Fig.13. Typical off-state leakage current. IL = f(Tj); conditions: VBL = 13 V = VBG ; VIG = 0 V. Fig.14. Typical input characteristics, Tj = 25 ˚C. II = f(VIG); parameter VBG Fig.15. Typical input current, Tj = 25 ˚C. II = f(VBG ); condition VIG = 5 V 0 20 40 60 VBG / V IG / mA BUK207-50Y5 OPERATING QUIESCENT CLAMPING HIGH VOLTAGE 10 30 50 VIG = 3 V VIG = 0 V -60 -20 20 60 100 140 180 Tj / C IL BUK207-50Y100 uA 10 uA 1 uA 100 nA 10 nA 1 nA -60 -20 20 60 100 140 180 Tj / C IG / mA BUK207-50Y3 VBG / V = 0 2 4 6 8 VIG / V II / uA BUK207-50Y200 150 100 VBG / V = 5 -60 -20 20 60 100 140 180 Tj / C IB BUK207-50Y100 uA 10 uA 1 uA 100 nA 10 nA 0 20 40 VBG / V II / uA BUK207-50Y100 10 30 50 July 1996 7 Rev 1.000
Philips Semiconductors Product specification TOPFET high side switch BUK207-50Y SMD version of BUK203-50Y Fig.16. Typical input threshold voltages. VIG = f(Tj); conditions VBG = 13 V, IL = 100 mA Fig.17. Typical input clamping voltage. VIG = f(Tj); conditions II = 200 µA, VBG = 13 V Fig.18. Typical status characteristic, Tj = 25 ˚C. IS = f(VSG ); conditions VIG = VBG = 0 V Fig.19. Typical status leakage current. IS = f(Tj); conditions VSG = 5 V, VIG = VBG = 0 V Fig.20. Typical status low characteristic, Tj = 25 ˚C. IS = f(VSG ); conditions VIG = 5 V, VBG = 13 V, IL = 0 A Fig.21. Typical status low voltage, VSG = f(Tj). conditions IS = 50 µA, VIG = 5 V, VBG = 13 V, IL = 0 A -60 -20 20 60 100 140 180 Tj / C VIG / V BUK207-50Y3.0 2.5 2.0 1.5 1.0 VIG(ON) VIG(OFF) -60 -20 20 60 100 140 180 Tj / C IS BUK207-50Y10 uA 1 uA 100 nA 10 nA -60 -20 20 60 100 140 180 Tj / C VIG / V BUK207-50Y8.0 7.5 7.0 6.5 VSG / V IS / uA BUK207-50Y500 400 300 200 100 0 2 4 6 8 10 VSG / V IS / mA BUK207-50Y20 -60 -20 20 60 100 140 180 Tj / C VSG / V BUK207-50Y1 0.8 0.6 0.4 0.2 July 1996 8 Rev 1.000
Philips Semiconductors Product specification TOPFET high side switch BUK207-50Y SMD version of BUK203-50Y Fig.22. Typical status clamping voltage, VSG = f(Tj). parameter VIG; conditions IS = 100 µA, VBG = 13 V Fig.23. Low load current detection threshold. IL(OC) = f(Tj); conditions VIG = 5 V; VBG = 13 V Fig.24. Supply typical undervoltage thresholds. VBG(TO) = f(Tj); conditions VIG = 3 V; IL = 100 mA Fig.25. Supply typical overvoltage thresholds. VBG(LP) = f(Tj); conditions VIG = 5 V; IL = 100 mA Fig.26. Typical battery to ground clamping voltage. VBG = f(Tj); parameter IG Fig.27. Typical negative load clamping characteristic. IL = f(VLG ); conditions VIG = 0 V, tp = 300 µs, 25 ˚C -60 -20 20 60 100 140 180 Tj / C VSG / V BUK207-50Y8.0 7.5 7.0 6.5 VIG / V = -60 -20 20 60 100 140 180 Tj / C VBG(LP) / V BUK207-50Y47 on off -60 -20 20 60 100 140 180 Tj / C IL(OC) / mA BUK207-50Y200 100 typ. max. min. -60 -20 20 60 100 140 180 Tj / C VBG / V BUK207-50Y65 10 uA 1 mA IG = -60 -20 20 60 100 140 180 Tj / C VBG(TO) / V BUK207-50Y5 on off VLG / V IL / A BUK207-50Y10 July 1996 9 Rev 1.000
Philips Semiconductors Product specification TOPFET high side switch BUK207-50Y SMD version of BUK203-50Y Fig.28. Typical negative load clamping voltage. VLG = f(Tj); parameter IL; condition VIG = 0 V. Fig.29. Typical battery to load clamping voltage. VBL = f(Tj); parameter IL; condition IG = 5 mA. Fig.30. Typical reverse battery characteristic. IG = f(VBG ); conditions IL = 0 A, Tj = 25 ˚C Fig.31. Typical reverse diode characteristic. IL = f(VBL); conditions VIG = 0 V, Tj = 25 ˚C Fig.32. Typical output capacitance. Tmb = 25 ˚C C bl = f(VBL); conditions f = 1 MHz, VIG = 0 V Fig.33. Typical overload characteristic, Tmb = 25 ˚C. IL = f(VBL); condition VBG = 13 V; parameter tp -60 -20 20 60 100 140 180 Tj / C VLG / V BUK207-50Y -22 -20 -18 -16 -14 -12 -10 2 A 1 mA IL = tp = 300 us VBL / V IL / A BUK207-50Y0 -10 -15 -20 -60 -20 20 60 100 140 180 Tj / C VBL / V BUK207-50Y65 100 uA 1 mA 1 A IL = tp = 300 us 0 20 40 VBL / V Cbl / pF BUK207-50Y1000 100 503010 -20 -10 0 VBG / V IG / mA BUK207-50Y0 -50 -100 -150 -15 -5 0 4 8 12 16 20 24 28 VBL / V IL / A BUK207-50Y20 current limiting i.e. before short circuit load trip 50 us VBL(TO) typ. tp = 300 us July 1996 10 Rev 1.000
Philips Semiconductors Product specification TOPFET high side switch BUK207-50Y SMD version of BUK203-50Y Fig.34. Typical overload current, VBL = 9 V. IL = f(Tmb ); conditions VBG = 13 V; tp = 100 µs Fig.35. Typical short circuit load threshold voltage. VBL(TO) = f(VBG ); condition Tmb = 25 ˚C Fig.36. Typical short circuit load threshold voltage. VBL(TO) = f(Tmb ); condition VBG = 13 V Fig.37. Transient thermal impedance. Zth j-mb = f(t); parameter D = tp/T -60 -20 20 60 100 140 180 Tmb / C IL(LIM) / A BUK207-50Y20 -60 -20 20 60 100 140 180 Tmb / C VBL(TO) / V BUK207-50Y15 0 10 20 30 40 VBG / V VBL(TO) / V BUK207-50Y12 100n 10u 1m 100m 10 t / s Zth j-mb / (K/W) BUK207-50Y10 0.1 0.01 0.5 0.2 0.1 0.05 0.02 1u 100u 10m 1 D = tp tp T TP t D D = July 1996 11 Rev 1.000
Philips Semiconductors Product specification TOPFET high side switch BUK207-50Y SMD version of BUK203-50Y MECHANICAL DATA Dimensions in mm Net Mass: 1.5 g Fig.38. SOT426 mounting base connected to centre pin (cropped short) MOUNTING INSTRUCTIONS Dimensions in mm Fig.39. SOT426 soldering pattern for surface mounting.
10.3 MAX
11 MAX
15.4 2.5 0.5
1.4 MAX
4.5 MAX
0.85 MAX
(x4) 3.4 3.4 1.7 1.7 11.5 9.0 3.8 1.3 (x4) 1.7 3.4 1.7 17.5 July 1996 12 Rev 1.000
Philips Semiconductors Product specification TOPFET high side switch BUK207-50Y SMD version of BUK203-50Y DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications. Limiting values Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of this specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Where application information is given, it is advisory and does not form part of the specification. Philips Electronics N.V. 1996 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, it is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. July 1996 13 Rev 1.000