BUF634 250mA High-Speed Buffer datasheet (Rev. C)
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 40
Technical content
BUF634 250mA High-Speed Buffer
1 Features
- A newer version of this device is now available: BUF634A
- High output current: 250mA
- Slew rate: 2000V/µs
- Pin-selected bandwidth: 30MHz to 180MHz
- Low quiescent current: 1.5mA (30MHz BW)
- Wide supply range: ±2.25V to ±18V
- Internal current limit
- Thermal shutdown protection
- Packages: – 5-pin SOIC – 5-pin TO-220 – 5-pin TO-263 surface-mount
2 Applications
- Valve driver
- Solenoid driver
- Op amp current booster
- Line driver
- Headphone driver
- Video driver
- Motor driver
- Test equipment
- ATE pin driver
3 Description
The BUF634 is a high-speed, unity-gain, open-loop buffer recommended for a wide range of applications. The BUF634 can be used inside the feedback loop of op amps to increase output current, eliminate thermal feedback, and improve capacitive load drive. For low-power applications, the BUF634 operates on 1.5mA quiescent current with 250mA output, 2000V/µs slew rate, and 30MHz bandwidth. Bandwidth can be adjusted from 30MHz to 180MHz by connecting a resistor between V– and the BW pin. Output circuitry is fully protected by internal current limit and thermal shutdown, making the device rugged and easy to use. The BUF634 is available in a variety of packages to meet mechanical and power-dissipation requirements. Types include SOIC‑8 surface-mount, 5 ‑lead TO‑220, and a 5 ‑lead TO‑263 (DDPAK) surface-mount plastic power packages.
Package Information
PART NUMBER PACKAGE(1) PACKAGE SIZE(2) BUF634 D (SOIC, 8) 4.9mm × 6mm KC (TO-220, 5) 10.16mm × 4.45mm KTT (TO-263, 5) 10.16mm × 15.24mm (1) For more information, see Section 11. (2) The package size (length × width) is a nominal value and includes pins, where applicable. OPA 281 0 1 2 Boost the Output Current of any Operational Amplifier BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA.
6.5 Electrical Characteristics: TO-220 and TO-263
6.6 Electrical Characteristics: Wide-Bandwidth Mode
6.7 Electrical Characteristics: Low-Quiescent-
6.8 Typical Characteristics: TO-220 and TO-263
11 Mechanical, Packaging, and Orderable
4 Device Comparison Table
DEVICE VS± (V) IQ/CHANNEL (mA) BW (MHz) SLEW RATE (V/µs) VOLTAGE NOISE (nV/√HZ) AMPLIFIER DESCRIPTION BUF634A ±18 1.5 to 8.5 35 to 210 3750 3.4 Unity-gain, open-loop buffer BUF634 ±18 1.5 to 15 30 to 180 2000 4 Unity-gain, open-loop buffer LMH6321 ±18 11 110 1800 2.8 Unity-gain, open-loop buffer with adjustable current limit BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 www.ti.com
2 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: BUF634
5 Pin Configuration and Functions
V O NC G = 1 Figure 5-1. D Package, 8-Pin SOIC (Top View) G = 1 VO VIN BW 1 2 3 4 5 Figure 5-2. KC Package, 5-Pin TO-220 (Top View) G = 1 VO VIN BW 1 2 3 4 5 Figure 5-3. KTT Package, 5-Pin TO-263 (Top View) Table 5-1. Pin Functions PIN TYPE DESCRIPTION NAME NO. D (SOIC) KC (TO-220) KTT (TO-263) BW 1 1 Input Bandwidth adjust pin NC 2, 5, 8 — — No internal connection V+ 7 5 Input Positive power supply VIN 3 2 Input Input VO 6 4 Output Output V– 4 3 Input Negative power supply www.ti.com BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 3 Product Folder Links: BUF634
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1) MIN MAX UNIT Supply voltage ±18 V Input voltage ±VS Output short-circuit (to ground) Continuous Operating temperature –40 125 °C Junction temperature 150 °C Lead temperature (soldering, 10 s) 300 °C Tstg Storage temperature –55 125 °C (1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
6.2 ESD Ratings
BUF634U in D (SOIC) Package V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2500 V BUF634U in D (SOIC) Package V(ESD) Electrostatic discharge, Charged-device model (CDM), per JEDEC specification JESD22-C101(2) ±1000 V BUF634F in KC (TO-220) and KTT (TO-263) Packages V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2500 V (1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. (2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted) MIN NOM MAX UNIT VS = (V+) – (V–) Supply voltage ±2.25 (4.5) ±15 (30) ±18 (36) V TA Operating temperature -40 25 85 °C
6.4 Thermal Information
THERMAL METRIC(1) BUF634 UNITD (SOIC) KC (TO-220) KTT (TO-263)
8 PINS 5 PINS 5 PINS
RθJA Junction-to-ambient thermal resistance 123 32.1 41.8 °C/W RθJC(top) Junction-to-case (top) thermal resistance 55 25.6 45 °C/W RθJB Junction-to-board thermal resistance 68 18.3 24.8 °C/W ψJT Junction-to-top characterization parameter 12 8.5 13.1 °C/W ψJB Junction-to-board characterization parameter 67 17.7 23.8 °C/W RθJC(bot) Junction-to-case (bottom) thermal resistance N/A 0.7 2.4 °C/W (1) For information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report. BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 www.ti.com
4 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: BUF634
6.5 Electrical Characteristics: TO-220 and TO-263 Packages
at TA = +25°C(1), VS = ±15 V, specifications are for both low quiescent-current mode and wide-bandwidth mode (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT INPUT Offset voltage ±30 ±100 mV Offset voltage vs temperature Specified temperature range ±100 µV/°C Offset voltage vs power supply VS = ±2.25 V(2) to ±18 V 0.1 1 mV/V Input bias current VIN = 0 V Low quiescent current mode ±0.5 ±2 µA Wide bandwidth mode ±5 ±20 Input impedance RL = 100 Ω Low quiescent current mode 80 || 8 MΩ || pF Wide bandwidth mode 8 || 8 Noise voltage f = 10 kHz 4 nV/√Hz GAIN Gain RL = 1 kΩ, VO = ±10 V 0.95 0.99 V/VRL = 100 Ω, VO = ±10 V 0.85 0.93 RL = 67 Ω, VO = ±10 V 0.8 0.9 OUTPUT Current output, continuous ±250 mA Voltage output Positive IO = 10 mA (V+) – 2.1 (V+) – 1.7 V Negative IO = –10 mA (V–) + 2.1 (V–) + 1.8 Positive IO = 100 mA (V+) – 3 (V+) – 2.4 Negative IO = –100 mA (V–) + 4 (V–) + 3.5 Positive IO = 150 mA (V+) – 4 (V+) – 2.8 Negative IO = –150 mA (V–) + 5 (V–) +4 Short-circuit current Low quiescent current mode ±350 ±550 mA Wide bandwidth mode ±400 ±550 DYNAMIC RESPONSE Bandwidth, –3dB RL = 1 kΩ Low quiescent current mode 30 MHz Wide bandwidth mode 180 RL = 100 Ω Low quiescent current mode 20 Low quiescent current mode 160 Slew rate 20 Vp-p, RL = 100 Ω 2000 V/µs Settling time 0.1% 20-V step, RL = 100 Ω 200 ns 1% 50 Differential gain 3.58 MHz, VO = 0.7 V, RL = 150 Ω Low quiescent current mode 4% Wide bandwidth mode 0.4% Differential phase 3.58 MHz, VO = 0.7 V, RL = 150 Ω Low quiescent current mode 2.5 Wide bandwidth mode 0.1 www.ti.com BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 5 Product Folder Links: BUF634
6.5 Electrical Characteristics: TO-220 and TO-263 Packages (continued)
at TA = +25°C(1), VS = ±15 V, specifications are for both low quiescent-current mode and wide-bandwidth mode (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT POWER SUPPLY Specified operating voltage ±15 V Operating voltage ±2.25(2) ±18 V IQ Quiescent current IO = 0 mA Low quiescent current mode ±1.5 ±2 mA Wide bandwidth mode ±15 ±20 TEMPERATURE TJ Thermal shutdown temperature 175 °C (1) Tests are performed on high-speed automatic test equipment, at approximately 25°C junction temperature. The power dissipation of this product causes some parameters to shift when warmed up. See Section 6.8 for overtemperature performance. (2) Limited output swing available at low supply voltage. See output voltage specifications. BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 www.ti.com
6 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: BUF634
6.6 Electrical Characteristics: Wide-Bandwidth Mode for SOIC Package
at TA = 25°C, VS = ±15 V, BW pin connected to V–, and RL = 100 Ω connected to mid-supply (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT AC PERFORMANCE BW Bandwidth, –3 dB RL = 1 kΩ 210 MHz RL = 100 Ω 200 Bandwidth for 0.1-dB flatness VO = 10 mVPP, RL = 100 Ω, RS = 50 Ω 50 MHz SR Slew rate VO = 20-V step, VIN-SR = 4000 V/µs 3750 V/µs Rise and fall time VO = 200-mV step 1.3 ns Settling time to 0.1% VO = 20-V step, VIN-SR = 2500 V/µs 90 ns Settling time to 1% VO = 20-V step, VIN-SR = 2500 V/µs 20 ns en Voltage noise f = 1 kHz 3.4 nV/√Hz in Current noise f = 100 kHz 0.85 pA/√Hz HD2 2nd-harmonic distortion VO = 2 VPP, f = 20 kHz –77 dBc VO = 10 VPP, f = 20 kHz –69 HD3 3rd-harmonic distortion VO = 2 VPP, f = 20 kHz –77 dBc VO = 10 VPP, f = 20 kHz –56 DC PERFORMANCE VOS Input offset voltage TA = 25℃ 36 65 mV Input offset voltage drift(1) TA = –40℃ to 125℃ 175 µV/℃ IB Input bias current VIN = 0 V 0.25 2 µA G Gain VO = ±10 V, RL = 1 kΩ 0.95 0.99 V/VVO = ±10 V, RL = 100 Ω 0.93 0.95 VO = ±10 V, RL = 67 Ω 0.91 0.93 INPUT Linear input voltage range RL = 1 kΩ, IB < 10 µA –13 13 V ZIN Input impedance RL = 100 Ω 180 || 5 MΩ || pF OUTPUT Output headroom to supplies IO = ±10 mA 1.6 1.8 VIO = ±100 mA 2.0 2.2 IO = ±150 mA 2.2 2.5 IO Current output, continuous ±250 mA ISC Short-circuit current ±375 ±550 mA ZO Output impedance DC, IO = 10 mA 5 Ω POWER SUPPLY VS Operating voltage range ±2.25 ±18 V IQ Quiescent current IO = 0 mA 8.5 12 mA PSRR Power-supply rejection ratio VS = ±2.25 V to ±18 V 64 75 dB THERMAL SHUTDOWN Thermal shutdown temperature 180 ℃ (1) Based on electrical characterization over temperature of 35 devices. www.ti.com BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 7 Product Folder Links: BUF634
6.7 Electrical Characteristics: Low-Quiescent-Current Mode for SOIC Package
at TA = 25°C, VS = ±15 V, BW pin left open, and RL = 100 Ω connected to mid-supply (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT AC PERFORMANCE BW Bandwidth, –3 dB RL = 1 kΩ 35 MHz RL = 100 Ω 31 Bandwidth for 0.1-dB flatness VO = 10 mVPP, RL = 100 Ω, RS = 50 Ω 2.3 MHz SR Slew rate VO = 20-V step, VIN-SR = 4000 V/µs 3750 V/µs Rise and fall time VO = 200-mV step 4 ns Settling time to 0.1% VO = 20-V step, VIN-SR = 2500 V/µs 400 ns Settling time to 1% VO = 20-V step, VIN-SR = 2500 V/µs 90 ns en Voltage noise f = 1 kHz 8.1 nV/√Hz in Current noise f = 10 kHz 0.3 pA/√Hz HD2 2nd-harmonic distortion VO = 2 VPP, f = 20 kHz –54 dBc VO = 10 VPP, f = 20 kHz –65 HD3 3rd-harmonic distortion VO = 2 VPP, f = 20 kHz –40 dBc VO = 10 VPP, f = 20 kHz –44 DC PERFORMANCE VOS Input offset voltage TA = 25℃ 36 65 mV Input offset voltage drift(1) TA = –40℃ to 125℃ 175 µV/℃ IB Input bias current VIN = 0 V 0.03 0.25 µA G Gain VO = ±10 V, RL = 1 kΩ 0.95 0.99 V/VVO = ±10 V, RL = 100 Ω 0.93 0.95 VO = ±10 V, RL = 67 Ω 0.91 0.93 INPUT Linear input voltage range RL = 1 kΩ, IB < 10 µA –13 13 V ZIN Input impedance RL = 100 Ω 1400 || 5 MΩ || pF OUTPUT Output headroom to supplies IO = ±10 mA 1.6 1.8 VIO = ±100 mA 2.0 2.2 IO = ±150 mA 2.2 2.5 IO Current output, continuous ±250 mA ISC Short-circuit current ±350 ±550 mA ZO Output impedance DC, IO = 10 mA 7 Ω POWER SUPPLY VS Operating voltage range ±2.25 ±18 V IQ Quiescent current IO = 0 mA 1.5 2.3 mA PSRR Power-supply rejection ratio VS = ±2.25 V to ±18 V 64 80 dB THERMAL SHUTDOWN Thermal shutdown temperature 180 ℃ (1) Based on electrical characterization over temperature of 35 devices. BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 www.ti.com
8 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: BUF634
6.8 Typical Characteristics: TO-220 and TO-263 Packages
at TA = 25°C, VS = ±15 V (unless otherwise noted) Frequency (Hz) 1M 10M 100M 1G Phase (°) –10 –20 –30 –40 –50 IQ = 15mA IQ = 9mA IQ = 4mA IQ = 2.5mA IQ = 1.5mA –10 –15 Gain (dB) RL = 100Ω RS = 50Ω VO = 10mV Figure 6-1. Gain and Phase vs Frequency vs Quiescent Current Frequency (Hz) 1M 10M 100M 1G Phase (°) –10 –20 –30 –40 –50 TJ = –40°C TJ = 25°C TJ = 125°C –10 –15 Gain (dB) Wide BW Wide BW Low IQ Low IQ RL = 100Ω RS = 50Ω VO = 10mV Figure 6-2. Gain and Phase vs Frequency vs Temperature Frequency (Hz) 1M 10M 100M 1G Phase (°) –10 –20 –30 –40 –50 RS = 0Ω RS = 50Ω RS = 100Ω –10 –15 Gain (dB) Wide BW Low IQ Low IQ Wide BW RL = 100Ω VO = 10mV Figure 6-3. Gain and Phase vs Frequency vs Source Resistance Frequency (Hz) 1M 10M 100M 1G Phase (°) –10 –20 –30 –40 –50 RL = 1kΩ RL = 100Ω RL = 50Ω –10 –15 Gain (dB) RS = 50Ω VO = 10mV Wide BW Low IQ Low IQ Wide BW Figure 6-4. Gain and Phase vs Frequency vs Load Resistance Frequency (Hz) 1M 10M 100M 1G Phase (°) –10 –20 –30 –40 –50 CL = 0pF CL = 50pF CL = 200pF CL = 1nF –10 –15 Gain (dB) Low IQ Mode RL = 100Ω RS = 50Ω VO = 10mV Figure 6-5. Gain and Phase vs Frequency vs Load Capacitance Frequency (Hz) 1M 10M 100M 1G Phase (°) –10 –20 –30 –40 –50 CL = 0 CL = 50pF CL = 200pF CL = 1nF –10 –15 Gain (dB)Wide BW Mode RL = 100Ω RS = 50Ω VO = 10mV Figure 6-6. Gain and Phase vs Frequency vs Load Capacitance www.ti.com BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 9 Product Folder Links: BUF634
6.8 Typical Characteristics: TO-220 and TO-263 Packages (continued)
at TA = 25°C, VS = ±15 V (unless otherwise noted) Frequency (Hz) 1M 10M 100M 1G Phase (°) –10 –20 –30 –40 –50 VS = ±18V VS = ±12V VS = ±5V VS = ±2.25V –10 –15 Gain (dB) Wide BW Low IQ Low IQ Wide BW RL = 100Ω RS = 50Ω VO = 10mV Figure 6-7. Gain and Phase vs Frequency vs Power Supply Voltage 100 1k 10k 100k 1M 10M Frequency (Hz) Wide BW Low IQ Power Supply Rejection (dB) Figure 6-8. Power Supply Rejection vs Frequency Resistance ( ) Ω 10 100 1k 10k Quiescent Current (mA) 15mA at R = 0 1.5mA at R = ∞ R – 15V +15V BW Figure 6-9. Quiescent Current vs Bandwidth Control Resistance 500 450 400 350 300 250 200 –50 –25 0 25 50 75 100 125 150 Junction Temperature (°C) Wide Bandwidth Mode Low IQ Mode Limit Current (mA) Figure 6-10. Short-Circuit Current vs Temperature Quiescent Current (mA) Junction Temperature (°C) –50 –25 0 25 50 75 100 125 150 175 200 Cooling Thermal Shutdown Low IQ Mode »10°C Figure 6-11. Quiescent Current vs Temperature Junction Temperature (°C) –50 –25 0 25 50 75 100 125 150 175 200 Thermal Shutdown »10°C Cooling Wide BW Mode Quiescent Current (mA) Figure 6-12. Quiescent Current vs Temperature BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 www.ti.com
10 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: BUF634
at TA = 25°C, VS = ±15 V (unless otherwise noted) –10 –11 –12 –13 0 50 100 150 200 250 300 |Output Current| (mA) TJ = –40°C TJ = 25°C TJ = 125°C VIN = 13V VIN = –13V VS = ±15V Low IQ Mode Output Voltage Swing (V) Figure 6-13. Output Voltage Swing vs Output Current –10 –11 –12 –13 0 50 100 150 200 250 300 |Output Current| (mA) TJ = –40°C TJ = 25°C TJ = 125°C VIN = 13V VIN = –13V VS = ±15V Wide BW Mode Output Voltage Swing (V) Figure 6-14. Output Voltage Swing vs Output Current Ambient Temperature (°C) –50 –25 0 25 50 75 100 125 150 Power Dissipation (W) TO-220 and DDPAK Free Air JA = 65°C/WΘ 8-Pin DIP JA = 100°C/WΘ SO-8 JA = 150°C/WΘ Figure 6-15. Maximum Power Dissipation vs Temperature Ambient Temperature (°C) Power Dissipation (W) –50 –25 0 25 50 75 100 125 150 TO-220 and DDPAK Infinite Heat Sink JC = 6°C/WΘ TO-220 and DDPAK Free Air JA = 65°C/WΘ Figure 6-16. Maximum Power Dissipation vs Temperature Input Wide BW Mode Low I Mode Q 100mV/div 20ns/div RS = 50 Ω, RL = 100 Ω Figure 6-17. Small-Signal Response Input Wide BW Mode Low I Mode Q 100mV/div 20ns/div RS = 50 Ω, RL = 100 Ω Figure 6-18. Large-Signal Response www.ti.com BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 11 Product Folder Links: BUF634
6.9 Typical Characteristics: SOIC Package
at TA = 25°C, VS = ±15 V, RS = 50 Ω, and RL = 100 Ω (unless otherwise noted). Frequency (Hz) Phase (o) Normalized Gain (dB) 100k 1M 10M 100M 1G -10 -150 -10 -20 -30 -40 -50 D001 8.6 mA 6.6 mA 4.9 mA 2.7 mA 1.5 mA Figure 6-19. Gain and Phase vs Frequency and Quiescent Current Frequency (Hz) Phase (o) Normalized Gain (dB) 100k 1M 10M 100M 1G -10 -20 -30 -40 -50 -10 -15 D002 -40oC 25oC 125oC Solid lines indicate wide-BW mode, dashed lines indicate low-IQ mode Figure 6-20. Gain and Phase vs Frequency and Temperature Frequency (Hz) Phase (o) Normalized Gain (dB) 100k 1M 10M 100M 1G -10 -20 -30 -40 -50 -10 -15 D003 RS = 0 : RS = 50 : RS = 100 : Solid lines indicate wide-BW mode, dashed lines indicate low-IQ mode Figure 6-21. Gain and Phase vs Frequency and Source Resistance Frequency (Hz) Phase (o) Normalized Gain (dB) 100k 1M 10M 100M 1G -10 -150 -10 -20 -30 -40 -50 D004 RL = 1 k: RL = 100 : RL = 50 : Solid lines indicate wide-BW mode, dashed lines indicate low-IQ mode Figure 6-22. Gain and Phase vs Frequency and Load Resistance Frequency (Hz) Phase (o) Normalized Gain (dB) 100k 1M 10M 100M 1G -10 -20 -30 -40 -50 -15 -10 D005 CL = 0 pF CL = 47 pF CL = 220 pF CL = 1 nF Low-IQ mode Figure 6-23. Gain and Phase vs Frequency and Load Capacitance Frequency (Hz) Phase (o) Normalized Gain (dB) 100k 1M 10M 100M 1G -10 -150 -10 -20 -30 -40 -50 D006 CL = 0 pF CL = 47 pF CL = 220 pF CL = 1 nF Wide-BW mode Figure 6-24. Gain and Phase vs Frequency and Load Capacitance BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 www.ti.com
12 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: BUF634
6.9 Typical Characteristics: SOIC Package (continued)
at TA = 25°C, VS = ±15 V, RS = 50 Ω, and RL = 100 Ω (unless otherwise noted). Frequency (Hz) Phase (o) Normalized Gain (dB) 100k 1M 10M 100M 1G -10 -150 -10 -20 -30 -40 -50 D007 VS = ±2.25 V VS = ±5 V VS = ±12 V VS = ±18 V Solid lines indicate wide-BW mode, dashed lines indicate low-IQ mode Figure 6-25. Gain and Phase vs Frequency and Power-Supply Voltage Frequency (Hz) Power Supply Rejection Ratio (dB) 100 10 100 1k 10k 100k 1M 10M D008 D008 PSRR+ PSRR Solid lines indicate wide-BW mode, dashed lines indicate low-IQ mode Figure 6-26. PSRR vs Frequency Frequency (Hz) Voltage Noise (nV/Hz) 10 100 1k 10k 100k D011 Low-IQ Wide-BW Figure 6-27. Voltage Noise Density vs Frequency Frequency (Hz) Current Noise (pA/Hz) 0.1 1 10 100 1k 10k 100k 1M 10M 0.1 100 D017 Low-IQ Wide-BW Figure 6-28. Current Noise Density vs Frequency Frequency (Hz) Harmonic Distortion (dBc) -120 -110 -100 -90 -80 -70 -60 -50 -40 100 1k 10k 100k 1M 10M D012 HD2 HD3 Wide-BW mode, VIN = 10 VPP, RL = 1 kΩ Figure 6-29. Harmonic Distortion vs Frequency Frequency (Hz) Harmonic Distortion (dBc) -80 -70 -60 -50 -40 100 1k 10k 100k 1M 10M D013 HD2 HD3 Wide-BW mode, VIN = 10 VPP, RL = 100 Ω Figure 6-30. Harmonic Distortion vs Frequency www.ti.com BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 13 Product Folder Links: BUF634
at TA = 25°C, VS = ±15 V, RS = 50 Ω, and RL = 100 Ω (unless otherwise noted). Frequency (Hz) Harmonic Distortion (dBc) -100 -90 -80 -70 -60 -50 -40 -30 100 1k 10k 100k 1M 10M D014 HD2 HD3 Low-IQ mode, VIN = 10 VPP, RL = 1 kΩ Figure 6-31. Harmonic Distortion vs Frequency Frequency (Hz) Harmonic Distortion (dBc) -70 -60 -50 -40 -30 100 1k 10k 100k 1M 10M D015 HD2 HD3 Low-IQ mode, VIN = 10 VPP, RL = 100 Ω Figure 6-32. Harmonic Distortion vs Frequency Resistance (:) -3 dB Bandwidth (MHz) 120 150 180 210 240 10 100 1k 10k 100k 1M D001 RL = 1 k: RL = 100 : Figure 6-33. Small-Signal Bandwidth vs Bandwidth Adjustment Resistance Junction Temperature (oC) Limit Current (mA) -50 -25 0 25 50 75 100 125 150 275 300 325 350 375 400 425 D016 Low-IQ Wide-BW Figure 6-34. Short-Circuit Current vs Temperature |Output Current| (mA) Output Voltage Swing - Sourcing (V) Output Voltage Swing - Sinking (V) 0 50 100 150 200 250 12.3 -14 12.6 -13.6 12.9 -13.2 13.2 -12.8 13.5 -12.4 13.8 -12 14.1 -11.6 D035 TA = 25oC TA = -40oC TA = 125oC Wide-BW mode (solid lines indicate sourcing current, dashed lines indicate sinking current) Figure 6-35. Output Voltage Swing vs Output Current |Output Current| (mA) Output Voltage Swing - Sourcing (V) Output Voltage Swing - Sinking (V) 0 50 100 150 200 250 12 -14.4 12.3 -14 12.6 -13.6 12.9 -13.2 13.2 -12.8 13.5 -12.4 13.8 -12 14.1 -11.6 D034 TA = -40oC TA = 25oC TA = 125oC Low-IQ mode (solid lines indicate sourcing current, dashed lines indicate sinking current) Figure 6-36. Output Voltage Swing vs Output Current BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 www.ti.com
14 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: BUF634
at TA = 25°C, VS = ±15 V, RS = 50 Ω, and RL = 100 Ω (unless otherwise noted). Time (50 ns/div) Input and Output Voltage (V) -12 -10 D010 VIN VO-Low-IQ VO-Wide-BW Figure 6-37. Large-Signal Transient Response Time (20 ns/div) Input and Output Voltage (V) -0.15 -0.1 -0.05 0.05 0.1 0.15 0.2 D009 VIN VO-Low-IQ VO-Wide-BW Figure 6-38. Small-Signal Transient Response Output Current (mA) Output Impedance (:) 0 50 100 150 200 250 100 D030 Low-IQ Wide-BW f = 100 kHz Figure 6-39. Output Impedance vs Output Current Frequency (Hz) Output Impedance (:) 10 100 1k 10k 100k 1M 10M 100M D036 Low-IQ: Sinking Low-IQ: Sourcing Wide-BW: Sinking Wide-BW: Sourcing IO = 100 mA Figure 6-40. Output Impedance vs Frequency Supply Voltage (V) Offset Voltage (mV) 4 8 12 16 20 24 28 32 36 D020 TA = 40oC TA = 25oC TA = 85oC TA = 125oC Figure 6-41. Offset Voltage vs Supply Voltage Offset Voltage (mV) No. of Units in Each Bin 1000 2000 3000 4000 5000 6000 D032 14000 devices, µ = 35.7 mV, σ = 2.15 mV Figure 6-42. Offset Voltage Distribution Histogram www.ti.com BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 15 Product Folder Links: BUF634
at TA = 25°C, VS = ±15 V, RS = 50 Ω, and RL = 100 Ω (unless otherwise noted). Ambient Temperature (oC) Offset Voltage (mV) -50 -25 0 25 50 75 100 125 150 D021 35 devices Figure 6-43. Offset Voltage vs Temperature Input Offset Drift (PV/oC) No. of Units in Each Bin 110 115 120 125 130 135 140 145 150 155 D031 TA = –40°C to +125°C, 35 devices, µ = 134 μV/°C, σ = 7.4 μV/°C Figure 6-44. Offset Voltage Drift Distribution Histogram Supply Voltage (V) Input Bias Current (PA) 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 -0.2 -0.15 -0.1 -0.05 0.05 0.1 0.15 0.2 D022 Low-IQ mode, 35 devices Figure 6-45. Input Bias Current vs Supply Voltage Supply Voltage (V) Input Bias Current (PA) 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 -0.8 -0.6 -0.4 -0.2 0.2 0.4 0.6 0.8 D023 Wide-BW mode, 35 devices Figure 6-46. Input Bias Current vs Supply Voltage Supply Voltage (V) Quiescent Current (mA) 4 8 12 16 20 24 28 32 36 1.2 1.3 1.4 1.5 1.6 D024 Low-IQ mode, 35 devices Figure 6-47. Quiescent Current vs Supply Voltage Supply Voltage (V) Quiescent Current (mA) 4 8 12 16 20 24 28 32 36 7.5 8.5 D025 Wide-BW mode, 35 devices Figure 6-48. Quiescent Current vs Supply Voltage BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 www.ti.com
16 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: BUF634
at TA = 25°C, VS = ±15 V, RS = 50 Ω, and RL = 100 Ω (unless otherwise noted). Ambient Temperature (oC) Quiescent Current (mA) -50 -25 0 25 50 75 100 125 1.4 1.5 1.6 1.7 1.8 D028 Low-IQ mode, 35 devices Figure 6-49. Quiescent Current vs Temperature Ambient Temperature (oC) Quiescent Current (mA) -50 -25 0 25 50 75 100 125 7.5 7.9 8.3 8.7 9.1 9.5 D029 Wide-BW mode, 35 devices Figure 6-50. Quiescent Current vs Temperature Ambient Temperature (oC) Gain (V/V) -50 -25 0 25 50 75 100 125 0.93 0.935 0.94 0.945 0.95 0.955 0.96 D026 Low-IQ mode, 35 devices Figure 6-51. Buffer Gain vs Temperature Ambient Temperature (oC) Gain (V/V) -50 -25 0 25 50 75 100 125 0.94 0.945 0.95 0.955 0.96 0.965 0.97 D027 Wide-BW mode, 35 devices Figure 6-52. Buffer Gain vs Temperature Ambient Temperature (oC) Power Dissipation (W) -50 -25 0 25 50 75 100 125 150 0.5 1.5 D033 Figure 6-53. Maximum Power Dissipation vs Temperature www.ti.com BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 17 Product Folder Links: BUF634
7 Detailed Description
7.1 Overview
The BUF634 device is a high-speed, unity-gain open-loop buffer recommended for a wide range of applications. The BUF634 can be used inside the feedback loop of op amps to increase output current, eliminate thermal feedback, and improve capacitive load drive. For low-power applications, the BUF634 operates on 1.5-mA quiescent current with 250-mA output, 2000 ‑V/µs slew rate, and 30-MHz bandwidth. Bandwidth can be adjusted from 30 MHz to 180 MHz by connecting a resistor between V– and the BW pin; see Figure 6-9 and Figure 6-1. Output circuitry is fully protected by internal current limit and thermal shutdown, making this device rugged and easy to use. For a simplified circuit diagram of the BUF634 showing the open-loop complementary follower design, see Section 7.2.
7.2 Functional Block Diagram
200Ω (1) VO BW V– 150Ω 4kΩ Signal path indicated in bold. Note: (1) Stage currents are set by I Thermal Shutdown VIN Figure 7-1. Internal Block Diagram: TO-220 and TO-263 8 k 1.2 k BW VIN VO Thermal Shutdown (1) Figure 7-2. Internal Block Diagram: SOIC BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 www.ti.com
18 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: BUF634
7.3 Feature Description
7.3.1 Output Current
The BUF634 delivers up to ±250-mA continuous output current. Internal circuitry limits output current to approximately ±350 mA; see Figure 6-10 . For many applications, however, the continuous output current is limited by thermal effects. The output voltage swing capability varies with junction temperature and output current; see Figure 6-14 . Although all four package types are tested for the same output performance using a high speed test, the higher junction temperatures with the DIP and SO-8 package types often provide less output voltage swing. Junction temperature is reduced in the TO-263 surface-mount power package because this package is soldered directly to the circuit board. The TO-220 package used with a good heat sink further reduces junction temperature, allowing maximum possible output swing.
7.4 Device Functional Modes
The BUF634 is operational when the power-supply voltage is greater than 4.5 V (±2.25 V). The maximum power supply voltage for the BUF634 is 36 V (±18 V). At low power supply conditions, such as ±2.25 V, the output swing can be limited. For additional information, see Section 6.5. www.ti.com BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 19 Product Folder Links: BUF634
8 Application and Implementation
Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI’s customers are responsible for determining suitability of components for their purposes, as well as validating and testing their design implementation to confirm system functionality.
8.1 Application Information
Figure 8-1 shows the BUF634 device connected as an open-loop buffer. The source impedance and optional input resistor, R S, influence frequency response: see Section 6.8. Bypass power supplies with capacitors connected close to the device pins. Capacitor values as low as 0.1 µF provide stable operation in most applications, but high output current and fast output slewing can demand large current transients from the power supplies. Solid tantalum 10-µF capacitors are recommended. High-frequency, open-loop applications can benefit from special bypassing and layout considerations. For more information, see Section 8.1.1. 10µF 10µF VOBUF634 Optional connection for wide bandwidth — see text. RS 3 RL4 VIN DIP/SO-8 Pinout shown Figure 8-1. Buffer Connections
8.1.1 High Frequency Applications
The excellent bandwidth and fast slew rate of the BUF634 device are useful in a variety of high frequency open-loop applications. When operated open-loop, printed-circuit-board layout and bypassing technique can affect dynamic performance. For best results, use a ground plane-type circuit board layout and bypass the power supplies with 0.1-µF ceramic chip capacitors at the device pins in parallel with solid tantalum 10-µF capacitors. Source resistance affects high-frequency peaking, step-response overshoot and ringing. Best response is usually achieved with a series input resistor of 25 Ω to 200 Ω, depending on the signal source. Response with some loads (especially capacitive) can be improved with a resistor of 10 Ω to 150 Ω in series with the output. Figure 8-2. High Performance Headphone Driver BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 www.ti.com
20 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: BUF634
8.2 Typical Application
8.2.1 Boosting Op Amp Output Current
The BUF634 device can be connected inside the feedback loop of most op amps to increase output current (see Figure 8-6). When connected inside the feedback loop, the offset voltage of the BUF634 device and other errors are corrected by the feedback of the op amp. OP AMP RECOMMENDA TIONS OPA177, OPA1013 Use Low I Q mode. G = 1 stable. OPA111, OPA2111 OPA121, OPA234(1), OPA130(1) OPA27, OPA2107 Low I Q mode is stable. Increasing C L may cause OPA602, OPA131(1) excessive ringing or instability. Use Wide BW mode. OPA627, OPA132(1) Use Wide BW mode, C 1 = 200pF. G = 1 stable. OPA637, OPA37 Use Wide BW mode. These op amps are not G = 1 stable. Use in G > 4. NOTE: (1) Single, dual, and quad versions. OP A NOTE: (1) C1 not required for most common op amps. Use with unity-gain stable high speed op amps. V IN VO BUF634 C1(1) Wide BW mode (if required) BW Figure 8-6. Boosting Op Amp Output Current
8.2.1.1 Design Requirements
- Boost the output current of an OPA627
- Operate from ±15V power supplies
- Operate from -40°C to +85°C
- Gain = 23.5 V/V
- Output current = ±250 mA
- Bandwidth greater than 100 kHz
8.2.1.2 Detailed Design Procedure
To make sure that the composite amplifier remains stable, the phase shift of the BUF634 must remain small throughout the loop gain of the circuit. For a G = +1 op-amp circuit, the BUF634 must contribute little additional phase shift (approximately 20° or less) at the unity-gain frequency of the op amp. Phase shift is affected by various operating conditions that can affect stability of the op amp; see Section 6.8. Most general-purpose or precision op amps remain unity-gain stable with the BUF634 connected inside the feedback loop as shown. Large capacitive loads can require the BUF634 to be connected for wide bandwidth and stable operation. High-speed or fast-settling op amps generally require the wide bandwidth mode to remain stable and to maintain good dynamic performance. To check for stability with an op amp, look for oscillations or excessive ringing on signal pulses with the intended load, and worst-case conditions that affect phase response of the buffer. Connect the circuit as shown in Figure 8-6. Choose resistors to provide a voltage gain of 23.5 V/V. Select the feedback resistor to be 2.7 kΩ. Choose the input resistor to be 120 Ω. BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 www.ti.com
22 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: BUF634
8.2.1.3 Application Curve
Frequency (Hz) Gain (db) 100 1k 10k 100k 1M Figure 8-7. Frequency Response of Composite Amplifier
8.3 Power Supply Recommendations
The BUF634 is specified for operation from 4.5V to 36 V (±2.25 V to ±18 V). Many specifications apply from –40°C to +85°C. Parameters that can exhibit significant variance with regard to operating voltage or temperature are presented in Section 6.8.
8.4 Layout
8.4.1 Layout Guidelines
For best operational performance of the device, use good printed circuit board (PCB) layout practices, including:
- Noise can propagate into analog circuitry through the power pins of the circuit. Bypass capacitors are used to reduce the coupled noise by providing low-impedance power sources local to the analog circuitry. – Connect low-ESR, 0.1-µF ceramic bypass capacitors between each supply pin and ground, placed as close to the device as possible. A single bypass capacitor from V+ to ground is applicable for single- supply applications.
- Separate grounding for analog and digital portions of circuitry is one of the simplest and most-effective methods of noise suppression. One or more layers on multilayer PCBs are usually devoted to ground planes. A ground plane helps distribute heat and reduces EMI noise pickup. Make sure to physically separate digital and analog grounds paying attention to the flow of the ground current. For more detailed information refer to Circuit Board Layout Techniques, SLOA089.
- To reduce parasitic coupling, run the input traces as far away from the supply or output traces as possible. If these traces cannot be kept separate, crossing the sensitive trace perpendicular is much better as opposed to in parallel with the noisy trace.
- Place the external components as close to the device as possible. As illustrated in Figure 8-9
- Keep the length of input traces as short as possible. Always remember that the input traces are the most sensitive part of the circuit.
- Clean the PCB following board assembly for best performance.
- Any precision integrated circuit can experience performance shifts due to moisture ingress into the plastic package. Following any aqueous PCB cleaning process, bake the PCB assembly to remove moisture introduced into the device packaging during the cleaning process. A low temperature, post cleaning bake at 85°C for 30 minutes is sufficient for most circumstances. Power dissipated in the BUF634 causes the junction temperature to rise. A thermal protection circuit in the BUF634 disables the output when the junction temperature reaches approximately 175°C. When the thermal protection is activated, the output stage is disabled, allowing the device to cool. Quiescent current is approximately 6 mA during thermal shutdown. When the junction temperature cools to approximately 165°C, the output circuitry is again enabled. The die overheating can cause the protection circuit to cycle on and off with a www.ti.com BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 23 Product Folder Links: BUF634
period ranging from a fraction of a second to several minutes or more, depending on package type, signal, load and thermal environment. The thermal protection circuit is designed to prevent damage during abnormal conditions. Any tendency to activate the thermal protection circuit during normal operation is a sign of an inadequate heat sink or excessive power dissipation for the package type. The TO-220 package provides the best thermal performance. When the TO-220 is used with a properly sized heat sink, output is not limited by thermal performance. The TO-263 also has excellent thermal characteristics; for good heat dissipation, solder the mounting tab to a circuit board copper area. Figure 8-8 shows typical thermal resistance from junction to ambient as a function of the copper area. The mounting tab of the TO-220 and TO-263 packages is electrically-connected to the V– power supply. The DIP and SO-8 surface-mount packages are excellent for applications requiring high output current with low average power dissipation. To achieve the best possible thermal performance with the DIP or SO-8 packages, solder the device directly to a circuit board. Because much of the heat is dissipated by conduction through the package pins, sockets degrade thermal performance. Use wide circuit board traces on all the device pins, including pins that are not connected. With the DIP package, use traces on both sides of the printed circuit board if possible. Circuit Board Copper Area BUF634F Surface Mount Package THERMAL RESISTANCE vs CIRCUIT BOARD COPPER AREA Thermal Resistance, Θ JA (°C/W) 0 1 2 3 4 5 Copper Area (inches )2 BUF634F Surface Mount Package 1oz copper Figure 8-8. Thermal Resistance vs Circuit Board Copper Area
8.4.1.1 Power Dissipation
Power dissipation depends on power supply voltage, signal, and load conditions. With dc signals, power dissipation is equal to the product of output current times the voltage across the conducting output transistor, VS – V O. Power dissipation can be minimized by using the lowest possible power supply voltage necessary to provide the required output voltage swing. For resistive loads, the maximum power dissipation occurs at a dc output voltage of one-half the power supply voltage. Dissipation with ac signals is lower. The Power Amplifier Stress And Power Handling Limitations application bulletin explains how to calculate or measure power dissipation with unusual signals and loads. Any tendency to activate the thermal protection circuit indicates excessive power dissipation or an inadequate heat sink. For reliable operation, limit the junction temperature to 150°C, maximum. To estimate the margin of safety in a complete design, increase the ambient temperature until the thermal protection is triggered. The thermal protection triggers more than 45°C greater than the maximum expected ambient condition of your application. BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 www.ti.com
24 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: BUF634
8.4.2 Layout Example
VS± GND Ground (GND) plane on another layer OutputVIN Run the input trace as far away from the supply lines as possible Use low-ESR, ceramic bypass capacitor RS Place all passive components close to the device to reduce parasitic errors Use low-ESR, ceramic bypass capacitor Optional: Use for wide bandwidth
applications
10 µF 10 µF BUF634 SOIC Package Figure 8-9. BUF634 Layout Example www.ti.com BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 25 Product Folder Links: BUF634
9 Device and Documentation Support
9.1 Device Support
9.1.1 Development Support
9.1.1.1 TINA-TI™ Simulation Software (Free Download)
TINA-TI™ simulation software is a simple, powerful, and easy-to-use circuit simulation program based on a SPICE engine. TINA-TI simulation software is a free, fully-functional version of the TINA™ software, preloaded with a library of macromodels, in addition to a range of both passive and active models. TINA-TI simulation software provides all the conventional dc, transient, and frequency domain analysis of SPICE, as well as additional design capabilities. Available as a free download from the Design tools and simulation web page, TINA-TI simulation software offers extensive post-processing capability that allows users to format results in a variety of ways. Virtual instruments offer the ability to select input waveforms and probe circuit nodes, voltages, and waveforms, creating a dynamic quick-start tool. Note These files require that either the TINA software or TINA-TI software be installed. Download the free TINA-TI simulation software from the TINA-TI™ software folder.
9.1.1.2 TI Reference Designs
TI reference designs are analog solutions created by TI’s precision analog applications experts. TI reference designs offer the theory of operation, component selection, simulation, complete PCB schematic and layout, bill of materials, and measured performance of many useful circuits. TI reference designs are available online at https://www.ti.com/reference-designs.
9.2 Documentation Support
9.2.1 Related Documentation
For related documentation see the following:
- Texas Instruments, Combining an Amplifier With the BUF634 application bulletin
- Texas Instruments, Add Current Limit to the BUF634 application bulletin
- Texas Instruments, Power Amplifier Stress and Power Handling Limitations application bulletin
- Texas Instruments, Shelf-Life Evaluation of Lead-Free Component Finishes application report
9.3 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. Click on Notifications to register and receive a weekly digest of any product information that has changed. For change details, review the revision history included in any revised document.
9.4 Support Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight from the experts. Search existing answers or ask your own question to get the quick design help you need. Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 www.ti.com
26 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: BUF634
9.5 Trademarks
TINA-TI™ and TI E2E™ are trademarks of Texas Instruments. TINA™ is a trademark of DesignSoft, Inc. All trademarks are the property of their respective owners.
9.6 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
9.7 Glossary
TI Glossary This glossary lists and explains terms, acronyms, and definitions. NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision B (March 2019) to Revision C (March 2024) Page Changes from Revision A (November 2015) to Revision B (March 2019) Page
- Changed amplifier to OPA2810 and deleted table from Boost the Output Current of any Operational Amplifier Changes from Revision * (September 2000) to Revision A (April 2015) Page
- Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and
11 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. www.ti.com BUF634 SBOS030C – AUGUST 2000 – REVISED MARCH 2024 Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 27 Product Folder Links: BUF634
www.ti.com 18-Sep-2026 PACKAGING INFORMATION Orderable part number Status (1) Material type (2) Package | Pins Package qty | Carrier RoHS (3) Lead finish/ Ball material (4) MSL rating/ Peak reflow (5) Op temp (°C) Part marking (6) BUF634F/500 Last Time Buy Production DDPAK/ TO-263 (KTT) | 5 500 | LARGE T&R Yes SN Level-2-260C-1 YEAR -40 to 125 BUF634F BUF634F/500.A NRND Production DDPAK/ TO-263 (KTT) | 5 500 | LARGE T&R Yes SN Level-2-260C-1 YEAR -40 to 125 BUF634F BUF634F/500E3 NRND Production DDPAK/ TO-263 (KTT) | 5 500 | LARGE T&R Yes SN Level-2-260C-1 YEAR -40 to 125 BUF634F BUF634FKTTT Last Time Buy Production DDPAK/ TO-263 (KTT) | 5 250 | SMALL T&R Yes SN Level-2-260C-1 YEAR -40 to 125 BUF634F BUF634FKTTT.A NRND Production DDPAK/ TO-263 (KTT) | 5 250 | SMALL T&R Yes SN Level-2-260C-1 YEAR -40 to 125 BUF634F BUF634FKTTTE3 NRND Production DDPAK/ TO-263 (KTT) | 5 250 | SMALL T&R Yes SN Level-2-260C-1 YEAR -40 to 125 BUF634F BUF634T Last Time Buy Production TO-220 (KC) | 5 49 | TUBE Yes SN N/A for Pkg Type -40 to 125 BUF634T BUF634T.A NRND Production TO-220 (KC) | 5 49 | TUBE Yes SN N/A for Pkg Type -40 to 125 BUF634T BUF634TG3 NRND Production TO-220 (KC) | 5 49 | TUBE Yes SN N/A for Pkg Type -40 to 125 BUF634T BUF634U NRND Production SOIC (D) | 8 75 | TUBE Yes NIPDAU Level-3-260C-168 HR -40 to 125 BUF 634U BUF634U.B NRND Production SOIC (D) | 8 75 | TUBE Yes NIPDAU Level-3-260C-168 HR -40 to 125 BUF 634U BUF634U/2K5 Active Production SOIC (D) | 8 2500 | LARGE T&R Yes NIPDAU Level-3-260C-168 HR -40 to 125 BUF 634U BUF634U/2K5.B Active Production SOIC (D) | 8 2500 | LARGE T&R Yes NIPDAU Level-3-260C-168 HR -40 to 125 BUF 634U (1) Status: For more details on status, see our product life cycle. (2) Material type: When designated, preproduction parts are prototypes/experimental devices, and are not yet approved or released for full production. Testing and final process, including without limitation quality assurance, reliability performance testing, and/or process qualification, may not yet be complete, and this item is subject to further changes or possible discontinuation. If available for ordering, purchases will be subject to an additional waiver at checkout, and are intended for early internal evaluation purposes only. These items are sold without warranties of any kind. (3) RoHS values: Yes, No, RoHS Exempt. See the TI RoHS Statement for additional information and value definition. Addendum-Page 1
www.ti.com 18-Sep-2026 (4) Lead finish/Ball material: Parts may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two lines if the finish value exceeds the maximum column width. (5) MSL rating/Peak reflow: The moisture sensitivity level ratings and peak solder (reflow) temperatures. In the event that a part has multiple moisture sensitivity ratings, only the lowest level per JEDEC standards is shown. Refer to the shipping label for the actual reflow temperature that will be used to mount the part to the printed circuit board. (6) Part marking: There may be an additional marking, which relates to the logo, the lot trace code information, or the environmental category of the part. Multiple part markings will be inside parentheses. Only one part marking contained in parentheses and separated by a "~" will appear on a part. If a line is indented then it is a continuation of the previous line and the two combined represent the entire part marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2
PACKAGE MATERIALS INFORMATION www.ti.com 10-Aug-2026 TAPE AND REEL INFORMATION Reel Width (W1) REEL DIMENSIONS A0B0K0WDimension designed to accommodate the component lengthDimension designed to accommodate the component thicknessOverall width of the carrier tapePitch between successive cavity centersDimension designed to accommodate the component width TAPE DIMENSIONSK0 P1B0WA0Cavity QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE Pocket QuadrantsSprocket HolesQ1Q1Q2Q2Q3Q3Q4Q4User Direction of Feed P1ReelDiameter *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Reel Diameter (mm) Reel Width W1 (mm) (mm) (mm) (mm) (mm) W (mm) Pin1 Quadrant BUF634F/500 DDPAK/ TO-263 BUF634FKTTT DDPAK/ TO-263 Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION www.ti.com 10-Aug-2026 TAPE AND REEL BOX DIMENSIONS Width (mm) W LH *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) BUF634F/500 DDPAK/TO-263 KTT 5 500 356.0 356.0 45.0 BUF634FKTTT DDPAK/TO-263 KTT 5 250 356.0 356.0 45.0 BUF634U/2K5 SOIC D 8 2500 353.0 353.0 32.0 Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION www.ti.com 10-Aug-2026 TUBE L - Tube length T - Tube height W - Tube width B - Alignment groove width *All dimensions are nominal Device Package Name Package Type Pins SPQ L (mm) W (mm) T (µm) B (mm) BUF634T KC TO-220 5 49 546 31 11930 3.17 BUF634T.A KC TO-220 5 49 546 31 11930 3.17 BUF634TG3 KC TO-220 5 49 546 31 11930 3.17 BUF634U D SOIC 8 75 506.6 8 3940 4.32 BUF634U.B D SOIC 8 75 506.6 8 3940 4.32 Pack Materials-Page 3
www.ti.com PACKAGE OUTLINE C .228-.244 TYP [5.80-6.19] .069 MAX [1.75] 6X .050 [1.27] 8X .012-.020 [0.31-0.51] .150 [3.81] .005-.010 TYP [0.13-0.25] 0 - 8 .004-.010 [0.11-0.25] .010 [0.25].016-.050 [0.41-1.27] 4X (0 -15 ) A .189-.197 [4.81-5.00] NOTE 3 B .150-.157 [3.81-3.98] NOTE 4 4X (0 -15 ) (.041) [1.04] SOIC - 1.75 mm max heightD0008A SMALL OUTLINE INTEGRATED CIRCUIT 4214825/C 02/2019 NOTES: 1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed .006 [0.15] per side. 4. This dimension does not include interlead flash. 5. Reference JEDEC registration MS-012, variation AA. 1 8 .010 [0.25] C A B PIN 1 ID AREA SEATING PLANE .004 [0.1] C SEE DETAIL A DETAIL A TYPICAL SCALE 2.800
www.ti.com EXAMPLE BOARD LAYOUT .0028 MAX [0.07] ALL AROUND .0028 MIN [0.07] ALL AROUND (.213) [5.4] 6X (.050 ) [1.27] 8X (.061 ) [1.55] 8X (.024) [0.6] (R.002 ) TYP [0.05] SOIC - 1.75 mm max heightD0008A SMALL OUTLINE INTEGRATED CIRCUIT 4214825/C 02/2019 NOTES: (continued) 6. Publication IPC-7351 may have alternate designs. 7. Solder mask tolerances between and around signal pads can vary based on board fabrication site. METAL SOLDER MASK OPENING NON SOLDER MASK DEFINED SOLDER MASK DETAILS EXPOSED METAL OPENING SOLDER MASK METAL UNDER SOLDER MASK SOLDER MASK DEFINED EXPOSED METAL LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE:8X SYMM 4 5 SEE DETAILS SYMM
www.ti.com EXAMPLE STENCIL DESIGN 8X (.061 ) [1.55] 8X (.024) [0.6] 6X (.050 ) [1.27] (.213) [5.4] (R.002 ) TYP [0.05] SOIC - 1.75 mm max heightD0008A SMALL OUTLINE INTEGRATED CIRCUIT 4214825/C 02/2019 NOTES: (continued) 8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 9. Board assembly site may have different recommendations for stencil design. SOLDER PASTE EXAMPLE BASED ON .005 INCH [0.125 MM] THICK STENCIL SCALE:8X SYMM SYMM 4 5
www.ti.com PACKAGE OUTLINE C B 9.25 7.67 6.86 5.69 3.05 2.54 14.73 12.29 5X 1.02 0.64 4X 1.7 8.89 6.86 12.88 10.08 (6.275) 4.83 4.06 1.40 1.14 3.05 2.03 0.61 0.30 -3.96 3.71 6.8 2X (R1) OPTIONAL 16.51 MAX A10.67 9.65 (4.25) 4215009/A 01/2017 TO-220 - 16.51 mm max heightKC0005A TO-220 NOTES: 1. All controlling linear dimensions are in inches. Dimensions in brackets are in millimeters. Any dimension in brackets or parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. Shape may vary per different assembly sites.
0.25 C A B
(OPTIONAL) 1 5 OPTIONAL CHAMFER SCALE 0.850 NOTE 3 1 5 A A A A
www.ti.com EXAMPLE BOARD LAYOUT
0.07 MAX
ALL AROUND0.07 MAX ALL AROUND (1.45) (2) (R0.05) TYP 4X (1.45) 4X (2) 5X ( 1.2) (1.7) TYP (6.8) FULL R TYP TO-220 - 16.51 mm max heightKC0005A TO-220 4215009/A 01/2017 LAND PATTERN NON-SOLDER MASK DEFINED SCALE:12X PKG PKG METAL TYP SOLDER MASK OPENING, TYP 1 5
IMPORTANT NOTICE AND DISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, regulatory or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you fully indemnify TI and its representatives against any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI’s products are provided subject to TI’s Terms of Sale, TI’s General Quality Guidelines, or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products. Unless TI explicitly designates a product as custom or customer-specified, TI products are standard, catalog, general purpose devices. TI objects to and rejects any additional or different terms you may propose. IMPORTANT NOTICE Copyright © 2026, Texas Instruments Incorporated Last updated 10/2025