18-Channel, Gamma Voltage Generator with Two Programmable Vcom Channels datasheet (Rev. E)
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 31
Technical content
FEATURES
/C006818-CHANNEL GAMMA CORRECTION /C00682-CHANNEL PROGRAMMABLE V COM : 100mA IOUT /C006810-BIT RESOLUTION /C0068RAIL-TO-RAIL OUTPUT /C0068LOW SUPPLY CURRENT: 900 µA/ch /C0068SUPPLY VOLTAGE: 7V to 18V /C0068DIGITAL SUPPLY: 2.0V to 5.5V /C0068INDUSTRY-STANDARD, TWO-WIRE INTERFACE: 3.4MHz High-Speed Mode /C0068HIGH ESD RATING: 4kV HBM, 1kV CDM, 200V MM /C0068DEMO BOARD AND SOFTWARE AVAILABLE REFH OUT REFH Digital (2.0V to 5.5V) Analog (7V to 18V) REFLAOLD SCL SDA REFL OUT OUT 18 OUT 17 DAC Registers Control IF OUT 1 OUT 2
18 Output Channels plus
APPLICATIONS
/C0068REPLACES RESISTOR-BASED GAMMA SOLUTIONS /C0068TFT-LCD REFERENCE DRIVERS /C0068DYNAMIC GAMMA CONTROL
DESCRIPTION
The BUF20800 is a programmable voltage reference generator designed for gamma correction in TFT-LCD panels. It provides 18 programmable outputs for gamma correction and two channels for V COM adjustment, each with 10-bit resolution. This programmability replaces the traditional, time- consuming process of changing resistor values to optimize the various gamma voltages and allows designers to determine the correct gamma voltages for a panel very quickly. Required changes can also be easily implemented without hardware changes. The BUF20800 uses TI’s latest, small-geometry analog CMOS process, which makes it a very competitive choice for full production, not just evaluation. Programming of each output occurs through an industry- standard, two-wire serial interface. Unlike existing programmable buffers, the BUF20800 offers a high-speed mode that allows clock speeds up to 3.4MHz. For lower channel count, please contact your local sales or marketing representative. The BUF20800 is available in an HTSSOP-38 PowerPAD package. It is specified from −40°C to +85°C. BUF20800 RELATED PRODUCTS FEATURES PRODUCT 18-Channel Programmable, Two VCOM + OTP Memory BUF20820 12-Channel Programmable Buffer, 10-Bit BUF12800 Programmable VCOM BUF01900 11-, 6-, 4-Channel Gamma Correction Buffer, 18V SupplyBUFxx704 High-Speed VCOM , 1 and 2 Channels SN10501 Complete LCD DC/DC Solution TPS65100 BUF20800 SBOS329E − JUNE 2005 − REVISED DECEMBER 2007 18-Channel GAMMA VOLTAGE GENERATOR with Two Programmable VCOM Channels /C0080/C0082/C0079/C0068/C0085/C0067/C0084/C0073/C0079/C0078 /C0068/C0065/C0084/C0065 /C0105/C0110/C0102/C0111/C0114/C0109/C0097/C0116/C0105/C0111/C0110 /C0105/C0115 /C0099/C0117/C0114/C0114/C0101/C0110/C0116 /C0097/C0115 /C0111/C0102 /C0112/C0117/C0098/C0108/C0105/C0099/C0097/C0116/C0105/C0111/C0110 /C0100/C0097/C0116/C0101/C0046 /C0080/C0114/C0111/C0100/C0117/C0099/C0116/C0115 /C0099/C0111/C0110/C0102/C0111/C0114/C0109 /C0116/C0111 /C0115/C0112/C0101/C0099/C0105/C0102/C0105/C0099/C0097/C0116/C0105/C0111/C0110/C0115 /C0112/C0101/C0114 /C0116/C0104/C0101 /C0116/C0101/C0114/C0109/C0115 /C0111/C0102 /C0084/C0101/C0120/C0097/C0115 /C0073/C0110/C0115/C0116/C0114/C0117/C0109/C0101/C0110/C0116/C0115 /C0115/C0116/C0097/C0110/C0100/C0097/C0114/C0100 /C0119/C0097/C0114/C0114/C0097/C0110/C0116/C0121/C0046 /C0080/C0114/C0111/C0100/C0117/C0099/C0116/C0105/C0111/C0110 /C0112/C0114/C0111/C0099/C0101/C0115/C0115/C0105/C0110/C0103 /C0100/C0111/C0101/C0115 /C0110/C0111/C0116 /C0110/C0101/C0099/C0101/C0115/C0115/C0097/C0114/C0105/C0108/C0121 /C0105/C0110/C0099/C0108/C0117/C0100/C0101 /C0116/C0101/C0115/C0116/C0105/C0110/C0103 /C0111/C0102 /C0097/C0108/C0108 /C0112/C0097/C0114/C0097/C0109/C0101/C0116/C0101/C0114/C0115/C0046 www.ti.com Copyright 2005−2007, Texas Instruments Incorporated Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPAD is a registered trademark of Texas Instruments. All other trademarks are the property of their respective owners.
/C0066/C0085/C0070/C0050/C0048/C0056/C0048/C0048 SBOS329E − JUNE 2005 − REVISED DECEMBER 2007 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ABSOLUTE MAXIMUM RATINGS (1) Signal Input Terminals, SCL, SDA, AO, LD: ESD Rating: (1)Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not supported. (2)Short-circuit to ground, one amplifier per package. ORDERING INFORMATION (1) PRODUCT PACKAGE-LEAD PACKAGE DESIGNATOR PACKAGE MARKING BUF20800 HTSSOP-38 DCP BUF20800 (1)For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com.
/C0066/C0085/C0070/C0050/C0048/C0056/C0048/C0048 SBOS329E − JUNE 2005 − REVISED DECEMBER 2007 www.ti.com
ELECTRICAL CHARACTERISTICS
Boldface limits apply over the specified temperature range, TA = −40°C to +85°C. At TA = +25°C, VS = 18V, VSD = 5V, RL = 1.5kΩ connected to ground, and CL = 200pF, unless otherwise noted. BUF20800 PARAMETER CONDITIONS MIN TYP MAX UNIT ANALOG Gamma Output Swing—High OUT 1−9, Sourcing 10mA, VREFH = 17.8V, Code 1023 17.7 17.8 V OUT 10−18, Sourcing 10mA, VREFH = 17.8V, Code 1023 17.0 17.2 V Gamma Output Swing—Low OUT 1−9, Sinking 10mA, VREFL = 0.2V, Code 00 0.6 1.0 V OUT 10−18, Sinking 10mA, VREFL = 0.2V, Code 00 0.2 0.3 V VCOM Buffer Output Swing—High VCOM , Sourcing 100mA, VREFH = 17.8V 13 15.5 V VCOM Buffer Output Swing—Low VCOM , Sinking 100mA, VREFL = 0.2V 1 2.0 V Output Current(1) IO All Channels, Code 512, Sinking/Sourcing 40 45 mA REFH Input Range(2) 4 VS V REFL Input Range(2) GND VS − 4 V Integral Nonlinearity INL No Load, V REFH = 17V, VREFL = 1V 0.3 1.5 Bits Differential Nonlinearity DNL No Load, V REFH = 17V, VREFL = 1V 0.3 1 Bits Gain Error 0.12 % Program to Out Delay tD 5 µs Output Accuracy No Load, VREFH = 17V, VREFL = 1V ±20 ±50 mV Over Temperature ±25 mV Input Resistance at VREFH and VREFL R INH 100 M Ω Load Regulation, All ReferencesREG V OUT = VS/2, IOUT = +5mA to −5mA Step 0.5 1.5 mV/mA 40mA, All Channels VOUT = VS/2, ISINKING = 40mA, ISOURCING = 40mA 0.5 1.5 mV/mA ANALOG POWER SUPPLY Operating Range VS 7 18 V Total Analog Supply Current IS No Load 18 28 mA over Temperature 28 mA DIGITAL Logic 1 Input Voltage VIH 0.7 × VSD V Logic 0 Input Voltage VIL 0.3 × VSD V Logic 0 Output Voltage VOL ISINK = 3mA 0.15 0.4 V Input Leakage ±0.01 ±10 µA Clock Frequency fCLK Standard/Fast Mode 400 kHz High-Speed Mode 3.4 MHz DIGITAL POWER SUPPLY Operating Voltage Range VSD 2.0 5.5 V Digital Supply Current(3) ISD Outputs at Reset Values, No-Load, Two-Wire Bus Inactive 25 50 µA over Temperature 100 µA TEMPERATURE Specified Temperature Range −40 +85 °C Operating Temperature Range Junction Temperature < +125°C −40 +95 °C Storage Temperature Range −65 +150 °C Thermal Resistance, HTSSOP-38 Junction-to-Ambient /C0113JA 30 °C/W Junction-to-Case /C0113JC 15 °C/W (1)See typical characteristic Output Voltage vs Output Current. (2)See applications information section REFH and REFL Input Range. (3)See typical characteristic Digital Supply Current vs Temperature.
/C0066/C0085/C0070/C0050/C0048/C0056/C0048/C0048 SBOS329E − JUNE 2005 − REVISED DECEMBER 2007 www.ti.com PIN CONFIGURATIONS Top View HTSSOP (1) NC denotes no connection. (2) GNDD and GNDA are internally connected and must be at the same voltage potential. VCOM OUT 2 REFH NC (1) NC (1) OUT 1 OUT 2 OUT 3 OUT 4 OUT 5 OUT 6 GND A (2) VS OUT 7 OUT 8 OUT 9 REFH OUT V SD SCL SDA VCOM OUT 1 REFL NC (1) NC (1) REFL OUT OUT 18 OUT 17 OUT 16 OUT 15 OUT 14 GND A(2) VS OUT 13 OUT 12 OUT 11 OUT 10 GND D (2) LD AO PowerPAD Lead−Frame Die Pad Exposed on Underside
(2)GND A and GNDD must be connected together. (3)Connecting a capacitor to this node is not recommended. Figure 8. Typical Application Configuration
/C0066/C0085/C0070/C0050/C0048/C0056/C0048/C0048 SBOS329E − JUNE 2005 − REVISED DECEMBER 2007 www.ti.com DATA RATES The two-wire bus operates in one of three speed modes: /C0068Standard: allows a clock frequency of up to 100kHz; /C0068Fast: allows a clock frequency of up to 400kHz; and /C0068High-speed mode (or Hs mode): allows a clock frequency of up to 3.4MHz. The BUF20800 is fully compatible with all three modes. No special action is required to use the device in Standard or Fast modes, but High-speed mode must be activated. To activate High-speed mode, send a special address byte of 00001xxx, with SCL = 400kHz, following the START condition; xxx are bits unique to the Hs-capable master, which can be any value. This byte is called the Hs master code. (Note that this is different from normal address bytes—the low bit does not indicate read/write status.) The BUF20800 will respond to the High-speed command regardless of the value of these last three bits. The BUF20800 will not acknowledge this byte; the communication protocol prohibits acknowledgement of the Hs master code. On receiving a master code, the BUF20800 will switch on its Hs mode filters, and communicate at up to 3.4MHz. Additional high-speed transfers may be initiated without resending the Hs mode byte by generating a repeat START without a STOP. The BUF20800 will switch out of Hs mode with the next STOP condition. GENERAL CALL RESET AND POWER-UP The BUF20800 responds to a General Call Reset, which is an address byte of 00h (0000 0000) followed by a data byte of 06h (0000 0110). The BUF20800 acknowledges both bytes. Upon receiving a General Call Reset, the BUF20800 performs a full internal reset, as though it had been powered off and then on. It always acknowledges the General Call address byte of 00h (0000 0000), but does not acknowledge any General Call data bytes other than 06h (0000 0110). The BUF20800 automatically performs a reset upon power up. As part of the reset, all outputs are set to REFH −V REFL )/2. Other reset values are available as a custom modification—contact your TI representative for details. The BUF20800 resets all outputs to (VREFH −V REFL )/2 after sending the device address, if a valid DAC address is sent with bits D7 to D5 set to ‘100’. If these bits are set to ‘010’, only the DAC being addressed in this most significant byte (MSB) and the following least significant byte (LSB) will be reset. OUTPUT VOLTAGE Buffer output values are determined by the reference voltages (VREFH and VREFL ) and the decimal value of the binary input code used to program that buffer. The value is calculated using Equation 1: VOUT /C0043/C0426 VREFH /C0042VREFL 1024 /C0032Decimal Value of Code/C0427/C0041VREFL The valid voltage ranges for the reference voltages are: 4V /C0118V REFH /C0118VS /C00420.2V and 0.2V/C0118VREFL /C0118VS /C00424V The BUF20800 outputs are capable of a full-scale voltage output change in typically 5µs—no intermediate steps are required. OUTPUT LATCH Updating the DAC register is not the same as updating the DAC output voltage, because the BUF20800 features a double-buffered register structure. There are three methods for latching transferred data from the storage registers into the DACs to update the DAC output voltages. Method 1 requires externally setting the latch pin (LD) LOW, LD = LOW, which will update each DAC output voltage whenever its corresponding register is updated. Method 2 externally sets LD = HIGH to allow all DAC output voltages to retain their values during data transfer and until LD = LOW, which will then simultaneously update the output voltages of all DACs to the new register values. Use this method to transfer a future data set in advance to prepare for a very fast output voltage update. Method 3 uses software control. LD is maintained HIGH, and all DACs are updated when the master writes a 1 in bit 15 of any DAC register. The update will occur after receiving the 16-bit data for the currently-written register. The General Call Reset and the power-up reset will update the DAC regardless of the state of the latch pin. READ/WRITE OPERATIONS The BUF20800 is able to read from a single DAC, or multiple DACs, or write to the register of a single DAC, or multiple DACs in a single communication transaction. DAC addresses begin with 0000 0000, which corresponds to DAC_1, through 0001 0011, which corresponds to V COM OUT2. Write commands are performed by setting the read/write bit LOW. Setting the read/write bit HIGH will perform a read transaction. (1) (2)
- Send a START condition on the bus.
- Send the device address and read/write bit = LOW.
The BUF20800 will acknowledge this byte.
- Send a DAC address byte. Bits D7−D5 must be set to
- Bits D4−D0 are the DAC address. Only DAC
acknowledged. Table 3 shows the DAC addresses.
- Send two bytes of data for the specified DAC register.
after receiving the second byte.
- Send a STOP condition on the bus.
Table 3. DAC Addresses
- Send a START condition on the bus.
- Send the device address and read/write bit = LOW.
The BUF20800 will acknowledge this byte.
- Send either the DAC_1 address byte to start at the first
be the first in the sequence of DACs to be updated. through subsequent DACs in sequential order.
- Send the bytes of data; begin by sending the most
automatically updated after receiving the second byte. DAC register is updated after receiving the fourth byte. following DACs have been updated.
- Send a STOP condition on the bus.
register. See the Output Latch section.
- Send a START condition on the bus.
- Send the device address and read/write bit = LOW.
The BUF20800 will acknowledge this byte.
- Send the DAC address byte. Bits D7−D5 must be set
- Send a START or STOP/START condition on the bus.
- Send correct device address and read/write
- Receive two bytes of data. They are for the specified
- Acknowledge after receiving the first byte.
- Do not acknowledge the second byte to end the read
/C0066/C0085/C0070/C0050/C0048/C0056/C0048/C0048 SBOS329E − JUNE 2005 − REVISED DECEMBER 2007 www.ti.com To Read Multiple DACs: 1. Send a START condition on the bus. 2. Send the device address and read/write bit = LOW. The BUF20800 will acknowledge this byte. 3. Send either the DAC_1 address byte to start at the first DAC, or send the address byte for whichever DAC will be the first in the sequence of DACs to be read. The BUF20800 will begin with this DAC and step through subsequent DACs in sequential order. 4. Send a START or STOP/START condition on the bus. 5. Send correct device address and read/write bit = HIGH. The BUF20800 will acknowledge this byte. 6. Receive two bytes of data. They are for the specified DAC. The first received byte is the most significant byte (bits D15−D8, only bits D9 and D8 have meaning); the next byte is the least significant byte (bits D7−D0). 7. Acknowledge after receiving each byte of data except for the last byte. The acknowledge bit of the last byte should be HIGH to end the read operation. 8. When all desired DACs have been read, send a STOP or repeated START condition on the bus. Communication may be terminated by sending a premature STOP or START condition on the bus, or by not sending the acknowledge.
Write single DAC register. P4−P0 specify DAC address. If D15 = 0, the DACs are updated on the Latch pin. If D15 = 1, all DACs are updated when the current DAC register is updated. Write OperationWrite multiple DAC registers. P4−P0 specify start DAC address. If D15 = 0, the DACs are updated on the Latch pin. If D15 = 1, all DACs are updated when the current DAC register is updated. If D15 = 0, the DACs are uploaded on the Latch pin. If D15 = 1, all the DACs are updated when the current DAC register is updated. Figure 9. Timing Diagram for Write DAC Register
Read Operat ionRead single DAC register. P4−P0 specify DAC address. Read OperationRead multiple DAC registers. P4−P0 specify start DAC address. Figure 10. Timing Diagram for Read DAC Register
18 Gamma Channels
Figure 14. 20 Gamma Channel Solution −
18 Output Channels
NOTE: (1) Expected availability is Q4’ 06. Figure 15. 22-Channel Gamma Solution
register input structure, see the Output Latch section. Step 1: Check if LD pin is placed in HIGH state. Step 2: Write DAC Registers 1−18 with bit 15 always ‘0’. Figure 16. Dynamic Gamma Control
Figure 18. Industrial Applications for the BUF20800
/C0066/C0085/C0070/C0050/C0048/C0056/C0048/C0048 SBOS329E − JUNE 2005 − REVISED DECEMBER 2007 www.ti.com GENERAL POWERPAD DESIGN CONSIDERATIONS The BUF20800 is available in a thermally-enhanced PowerPAD package. This package is constructed using a downset leadframe upon which the die is mounted, as shown in Figure 20(a) and Figure 20(b). This arrangement results in the lead frame being exposed as a thermal pad on the underside of the package; see Figure 20(c). This thermal pad has direct thermal contact with the die; thus, excellent thermal performance is achieved by providing a good thermal path away from the thermal pad. The PowerPAD package allows for both assembly and thermal management in one manufacturing operation. During the surface-mount solder operation (when the leads are being soldered), the thermal pad must be soldered to a copper area underneath the package. Through the use of thermal paths within this copper area, heat can be conducted away from the package into either a ground plane or other heat-dissipating device. Soldering the PowerPAD to the printed circuit board (PCB) is always required, even with applications that have low power dissipation. This provides the necessary thermal and mechanical connection between the lead frame die pad and the PCB. The PowerPAD must be connected to the most negative supply voltage on the device, GND A and GNDD . 1. Prepare the PCB with a top-side etch pattern. There should be etching for the leads as well as etch for the thermal pad. 2. Place recommended holes in the area of the thermal pad. Ideal thermal land size and thermal via patterns (2x5) can be seen in the technical brief, PowerPAD Thermally-Enhanced Package (SLMA002), available for download at www.ti.com. These holes should be 13 mils (0.330mm) in diameter. Keep them small, so that solder wicking through the holes is not a problem during reflow. 3. Additional vias may be placed anywhere along the thermal plane outside of the thermal pad area. This helps dissipate the heat generated by the BUF20800 IC. These additional vias may be larger than the 13-mil diameter vias directly under the thermal pad. They can be larger because they are not in the thermal pad area to be soldered; thus, wicking is not a problem. 4. Connect all holes to the internal plane that is at the same voltage potential as the GND pins. 5. When connecting these holes to the internal plane, do not use the typical web or spoke via connection methodology. Web connections have a high thermal resistance connection that is useful for slowing the heat transfer during soldering operations. This makes the soldering of vias that have plane connections easier. In this application, however, low thermal resistance is desired for the most efficient heat transfer. Therefore, the holes under the BUF20800 PowerPAD package should make their connection to the internal plane with a complete connection around the entire circumference of the plated-through hole. 6. The top-side solder mask should leave the terminals of the package and the thermal pad area with its ten holes exposed. The bottom-side solder mask should cover the holes of the thermal pad area. This masking prevents solder from being pulled away from the thermal pad area during the reflow process. 7. Apply solder paste to the exposed thermal pad area and all of the IC terminals. 8. With these preparatory steps in place, the BUF20800 IC is simply placed in position and run through the solder reflow operation as any standard surface-mount component. This preparation results in a properly installed part.
www.ti.com 11-Nov-2025 PACKAGING INFORMATION Orderable part number Status (1) Material type (2) Package | Pins Package qty | Carrier RoHS (3) Lead finish/ Ball material (4) MSL rating/ Peak reflow (5) Op temp (°C) Part marking (6) BUF20800AIDCPR Active Production HTSSOP (DCP) | 38 2000 | LARGE T&R Yes NIPDAU Level-2-260C-1 YEAR -40 to 95 BUF20800 BUF20800AIDCPR.A Active Production HTSSOP (DCP) | 38 2000 | LARGE T&R Yes NIPDAU Level-2-260C-1 YEAR -40 to 95 BUF20800 BUF20800AIDCPRG4 Active Production HTSSOP (DCP) | 38 2000 | LARGE T&R Yes NIPDAU Level-2-260C-1 YEAR -40 to 95 BUF20800 BUF20800AIDCPRG4.A Active Production HTSSOP (DCP) | 38 2000 | LARGE T&R Yes NIPDAU Level-2-260C-1 YEAR -40 to 95 BUF20800 (1) Status: For more details on status, see our product life cycle. (2) Material type: When designated, preproduction parts are prototypes/experimental devices, and are not yet approved or released for full production. Testing and final process, including without limitation quality assurance, reliability performance testing, and/or process qualification, may not yet be complete, and this item is subject to further changes or possible discontinuation. If available for ordering, purchases will be subject to an additional waiver at checkout, and are intended for early internal evaluation purposes only. These items are sold without warranties of any kind. (3) RoHS values: Yes, No, RoHS Exempt. See the TI RoHS Statement for additional information and value definition. (4) Lead finish/Ball material: Parts may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two lines if the finish value exceeds the maximum column width. (5) MSL rating/Peak reflow: The moisture sensitivity level ratings and peak solder (reflow) temperatures. In the event that a part has multiple moisture sensitivity ratings, only the lowest level per JEDEC standards is shown. Refer to the shipping label for the actual reflow temperature that will be used to mount the part to the printed circuit board. (6) Part marking: There may be an additional marking, which relates to the logo, the lot trace code information, or the environmental category of the part. Multiple part markings will be inside parentheses. Only one part marking contained in parentheses and separated by a "~" will appear on a part. If a line is indented then it is a continuation of the previous line and the two combined represent the entire part marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF BUF20800 : Addendum-Page 1
www.ti.com 11-Nov-2025
- Automotive : BUF20800-Q1 NOTE: Qualified Version Definitions:
- Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 2
PACKAGE MATERIALS INFORMATION www.ti.com 15-Jul-2025 TAPE AND REEL INFORMATION Reel Width (W1) REEL DIMENSIONS A0B0K0WDimension designed to accommodate the component lengthDimension designed to accommodate the component thicknessOverall width of the carrier tapePitch between successive cavity centersDimension designed to accommodate the component width TAPE DIMENSIONSK0 P1B0WA0Cavity QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE Pocket QuadrantsSprocket HolesQ1Q1Q2Q2Q3Q3Q4Q4User Direction of Feed P1ReelDiameter *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Reel Diameter (mm) Reel Width W1 (mm) (mm) (mm) (mm) (mm) W (mm) Pin1 Quadrant Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION www.ti.com 15-Jul-2025 TAPE AND REEL BOX DIMENSIONS Width (mm) W LH *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) BUF20800AIDCPR HTSSOP DCP 38 2000 350.0 350.0 43.0 BUF20800AIDCPRG4 HTSSOP DCP 38 2000 350.0 350.0 43.0 Pack Materials-Page 2
www.ti.com GENERIC PACKAGE VIEW This image is a representation of the package family, actual package may vary. Refer to the product data sheet for package details. PowerPAD TSSOP - 1.2 mm max heightDCP 38 SMALL OUTLINE PACKAGE4.4 x 9.7, 0.5 mm pitch 4224560/B
www.ti.com PACKAGE OUTLINE C 36X 0.5 38X 0.27 0.17 6.6
6.2 TYP
0.15 0.05 0.25 GAGE PLANE 0 -8
1.2 MAX
2X 0.95 MAX NOTE 5 2X 0.95 MAX NOTE 5 4.70 3.94 2.90 2.43 B 4.5 4.3 A 9.8 9.6 NOTE 3 0.75 0.50 (0.15) TYP PowerPAD TSSOP - 1.2 mm max heightDCP0038A SMALL OUTLINE PACKAGE 4218816/A 10/2018 19 20
0.08 C A B
0.1 C NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed 0.15 mm per side. 4. Reference JEDEC registration MO-153. 5. Features may differ or may not be present. TM PowerPAD is a trademark of Texas Instruments. A 20 DETAIL A TYPICAL SCALE 2.000 THERMAL PAD 19 20
www.ti.com EXAMPLE BOARD LAYOUT
0.05 MAX
0.05 MIN
38X (1.5) 38X (0.3) 36X (0.5) (5.8) (R0.05) TYP (3.4) NOTE 9 (9.7) NOTE 9 ( 0.2) TYP VIA (2.9) (4.7) (1.2) (0.6) TYP 3X (1.2) PowerPAD TSSOP - 1.2 mm max heightDCP0038A SMALL OUTLINE PACKAGE 4218816/A 10/2018 NOTES: (continued) 6. Publication IPC-7351 may have alternate designs. 7. Solder mask tolerances between and around signal pads can vary based on board fabrication site. 8. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature 9. Size of metal pad may vary due to creepage requirement. 10. Vias are optional depending on application, refer to device data sheet. It is recommended that vias under paste be filled, plugged or tented. TM LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE: 8X SYMM SYMM 19 20 METAL COVERED BY SOLDER MASK SOLDER MASK DEFINED PAD SEE DETAILS 15.000 METALSOLDER MASK OPENING METAL UNDER SOLDER MASK SOLDER MASK OPENING EXPOSED METALEXPOSED METAL SOLDER MASK DETAILS NON-SOLDER MASK DEFINED SOLDER MASK DEFINED
www.ti.com EXAMPLE STENCIL DESIGN 38X (1.5) 38X (0.3) 36X (0.5) (5.8) (R0.05) TYP (4.7) BASED ON
0.125 THICK
(2.9) BASED ON PowerPAD TSSOP - 1.2 mm max heightDCP0038A SMALL OUTLINE PACKAGE 4218816/A 10/2018 2.45 X 3.970.175 2.65 X 4.290.15 2.90 X 4.70 (SHOWN)0.125 3.24 X 5.250.1 SOLDER STENCIL OPENING STENCIL THICKNESS NOTES: (continued) 11. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 12. Board assembly site may have different recommendations for stencil design. TM SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE: 8X SYMM SYMM 19 20 METAL COVERED BY SOLDER MASK SEE TABLE FOR DIFFERENT OPENINGS FOR OTHER STENCIL THICKNESSES
IMPORTANT NOTICE AND DISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, regulatory or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you fully indemnify TI and its representatives against any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI’s products are provided subject to TI’s Terms of Sale, TI’s General Quality Guidelines, or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products. Unless TI explicitly designates a product as custom or customer-specified, TI products are standard, catalog, general purpose devices. TI objects to and rejects any additional or different terms you may propose. IMPORTANT NOTICE Copyright © 2025, Texas Instruments Incorporated Last updated 10/2025