BTA216X-600F

BTA216X PHILIPS

Document overview

• Manufacturer or author: Provided By digicamel.com
• PDF pages: 5

Technical content

Philips Semiconductors Objective specification Three quadrant triacs BTA216X series D, E and F guaranteed commutation GENERAL DESCRIPTION QUICK REFERENCE DATA Passivated guaranteed commutation SYMBOL PARAMETER MAX. MAX. UNIT triacs in a full pack, plastic envelope intended for use in motor control circuits BTA216X- 600D - or with other highly inductive loads. BTA216X- 600E 800E These devices balance the BTA216X- 600F 800F requirements of commutation V DRM Repetitive peak off-state 600 800 V performance and gate sensitivity. The voltages "sensitive gate" E series and "logic level" I T(RMS) RMS on-state current 16 16 A D series are intended for interfacing with ITSM Non-repetitive peak on-state 140 140 A low power drivers, including micro current controllers. PINNING - SOT186A PIN CONFIGURATION SYMBOL PIN DESCRIPTION 1 main terminal 1 2 main terminal 2 3 gate case isolated LIMITING VALUES Limiting values in accordance with the Absolute Maximum System (IEC 134). SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT -600 -800 VDRM Repetitive peak off-state - 600 1 800 V voltages IT(RMS) RMS on-state current full sine wave; - 16 A Ths ≤ 38 ˚C ITSM Non-repetitive peak full sine wave; on-state current T j = 25 ˚C prior to surge t = 20 ms - 140 A t = 16.7 ms - 150 A I 2tI 2t for fusing t = 10 ms - 98 A 2s dIT/dt Repetitive rate of rise of ITM = 20 A; IG = 0.2 A; 100 A/ µs on-state current after dIG /dt = 0.2 A/µs triggering IGM Peak gate current - 2 A VGM Peak gate voltage - 5 V PGM Peak gate power - 5 W PG(AV) Average gate power over any 20 ms - 0.5 W period Tstg Storage temperature -40 150 ˚C Tj Operating junction - 125 ˚C temperature T1T2 G123 case 1 Although not recommended, off-state voltages up to 800V may be applied without damage, but the triac may switch to the on-state. The rate of rise of current should not exceed 15 A/µs. October 1999 1 Rev 1.000

Philips Semiconductors Objective specification Three quadrant triacs BTA216X series D, E and F guaranteed commutation ISOLATION LIMITING VALUE & CHARACTERISTIC Ths = 25 ˚C unless otherwise specified SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT V isol R.M.S. isolation voltage from all f = 50-60 Hz; sinusoidal - - 2500 V three terminals to external waveform; heatsink R.H. ≤ 65% ; clean and dustfree C isol Capacitance from T2 to external f = 1 MHz - 10 - pF heatsink THERMAL RESISTANCES SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT R th j-hs Thermal resistance full or half cycle junction to heatsink with heatsink compound - - 4.0 K/W without heatsink compound - - 5.5 K/W R th j-a Thermal resistance in free air - 55 - K/W junction to ambient STATIC CHARACTERISTICS Tj = 25 ˚C unless otherwise stated SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT IGT Gate trigger current2 VD = 12 V; IT = 0.1 A T2+ G+ - - 5 10 25 mA T2+ G- - - 5 10 25 mA T2- G- - - 5 10 25 mA IL Latching current V D = 12 V; IGT = 0.1 A T2+ G+ - - 15 20 25 mA T2+ G- - - 25 30 40 mA T2- G- - - 25 30 40 mA I H Holding current V D = 12 V; IGT = 0.1 A - - 15 25 30 mA VT On-state voltage I T = 20 A - 1.2 1.5 V VGT Gate trigger voltage V D = 12 V; IT = 0.1 A - 0.7 1.5 V VD = 400 V; IT = 0.1 A; 0.25 0.4 - V Tj = 125 ˚C ID Off-state leakage current VD = VDRM(max) ; - 0.1 0.5 mA Tj = 125 ˚C 2 Device does not trigger in the T2-, G+ quadrant. October 1999 2 Rev 1.000

Philips Semiconductors Objective specification Three quadrant triacs BTA216X series D, E and F guaranteed commutation DYNAMIC CHARACTERISTICS Tj = 25 ˚C unless otherwise stated SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT dVD /dt Critical rate of rise of VDM = 67% VDRM(max) ;3 0 6 0 7 0 - - V / µs off-state voltage T j = 110 ˚C; exponential waveform; gate open circuit dIcom /dt Critical rate of change of VDM = 400 V; Tj = 110 ˚C; 1.8 3.5 4.5 - - A/ms commutating current I T(RMS) = 16 A; dVcom /dt = 20v/µs; gate open circuit dIcom /dt Critical rate of change of VDM = 400 V; Tj = 110 ˚C; 4.3 5.3 6.3 - - A/ms commutating current I T(RMS) = 16 A; dVcom /dt = 0.1v/µs; gate open circuit tgt Gate controlled turn-on ITM = 20 A; VD = VDRM(max) ;- - - 2 - µs time I G = 0.1 A; dIG /dt = 5 A/µs October 1999 3 Rev 1.000

Philips Semiconductors Objective specification Three quadrant triacs BTA216X series D, E and F guaranteed commutation MECHANICAL DATA Dimensions in mm Net Mass: 2 g Fig.1. SOT186A; The seating plane is electrically isolated from all terminals. Notes 1. Refer to mounting instructions for F-pack envelopes. 2. Epoxy meets UL94 V0 at 1/8". 10.3 max 3.2 3.0 4.6 max 2.9 max 2.8 seating plane 6.4 15.8 max 0.6 2.5 2.54 5.08 123 3 max. not tinned 0.5 2.5 0.9 0.7 M0.4 15.8 max. max. 13.5 min. Recesses (2x) 2.5 0.8 max. depth 1.0 (2x) 1.3 October 1999 4 Rev 1.000

Philips Semiconductors Objective specification Three quadrant triacs BTA216X series D, E and F guaranteed commutation DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications. Limiting values Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of this specification is not implied. Exposure to limiting values for extended periods may affect device reliability.

Application information

Where application information is given, it is advisory and does not form part of the specification.  Philips Electronics N.V. 1999 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, it is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. October 1999 5 Rev 1.000