BA2901FV-E2

BA8391G ROHM

Document overview

• Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 57

Technical content

Features

 Operable with a Single Power Supply  Wide Operating Supply Voltage  Standard Pin Assignments  Input and Output are Ground Sense Operated  Open Collector  Wide Temperature Range Application  General Use  Current Monitor  Battery Monitor  Multi vibrator Key Specifications  Operating Supply Voltage(Single Supply): BA8391G/BA10393F +2.0V to +36.0V BA2903xxxx/BA2901xxx +2.0V to +36.0V BA10339xx +3.0V to +36.0V  Operating Supply Voltage(Split Supply): BA8391G/BA10393F ± 1.0V to ±18.0V BA2903xxxx/BA2901xxx ± 1.0V to ±18.0V BA10339xx ± 1.5V to ±18.0V  Temperature Range: BA8391G/BA10393F/BA10339xx -40°C to +85°C BA2903Sxxx/BA2901Sxx -40°C to +105°C BA2903xxx/BA2901xx -40°C to +125°C  Input Offset Voltage: BA2903Sxxx/BA2901Sxx 7mV(Max) BA8391G/BA2903xxx/BA2901xx 7mV(Max) BA10393F/BA10339xx 5mV(Max) BA2903Wxx 2mV(Max) Packages W(Typ) x D(Typ) x H(Max) SSOP5 2.90mm x 2.80mm x 1.25mm SOP8 5. 00mm x 6.20mm x 1.71mm SSOP-B8 3.00mm x 6.40mm x 1.35mm MSOP8 2.90mm x 4.00mm x 0.90mm SOP14 8.70mm x 6.20mm x 1.71mm SSOP-B14 5.00mm x 6.40mm x 1.35mm Selection Guide BA2903F BA2903FV BA2903FVM BA2903SF BA2903SFV BA2903SFVM +125°C Maximum operating temperature Input Offset Voltage (Max) BA10339F BA10339FV BA10393F BA2901F BA2901FV BA2901SF BA2901SFV +85°C +105°C General Purpose Dual Quad 5mV 5mV BA8391G Single 7mV High Reliability Dual 7mＶ Quad 7mV 2mV BA2903WF BA2903WFV Datasheet

2 VEE

4 OUT

5 VCC

1 OUT1

4 VEE

7 OUT2

8 VCC

Figure 1. Simplified Schematic (one channel only)

www.rohm.com TSZ02201-0RFR0G200200-1-2 TSZ22111 • 15 • 001 BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Se ries Pin Configuration - continued BA10339F, BA2901SF, BA2901F : SOP14 BA10339FV, BA2901SFV, BA2901FV : SSOP-B14 Package SSOP5 SOP8 SSOP-B8 MSOP8 SOP14 SSOP-B14 BA8391G BA10393F BA2903SF BA2903F BA2903WF BA2903SFV BA2903FV BA2903WFV BA2903SFVM BA2903FVM BA10339F BA2901SF BA2901F BA10339FV BA2901SFV BA2901FV

Ordering Information

G : SSOP5 F : SOP8 SOP14 FV : SSOP-B8 SSOP-B14 FVM : MSOP8 Packaging and forming specification E2: Embossed tape and reel (SOP8/SOP14/SSOP-B8/SSOP-B14) TR: Embossed tape and reel (SSOP5/MSOP8) Pin No. Pin Name

1 OUT2

2 OUT1

3 VCC

12 VEE

13 OUT4

14 OUT3

-IN1 +IN1 -IN2 +IN2 OUT3 OUT4 VEE +IN4 -IN4 +IN3 -IN3 － ＋ － ＋ － ＋ 7 8 CH1 CH3CH2 － ＋ CH4

www.rohm.com TSZ02201-0RFR0G200200-1-2 TSZ22111 • 15 • 001 BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Se ries Line-up Operating Temperature Range Input Offset Voltage (Max) Supply Current (Typ) Package Orderable Part Number -40°C to +85°C 7mV 0.3mA SSOP5 Reel of 3000 BA8391G-TR 5mV 0.4mA SOP8 Reel of 2500 BA10393F-E2 0.8mA SOP14 Reel of 2500 BA10339F-E2 SSOP-B14 Reel of 2500 BA10339FV-E2 -40°C to +105°C 7mV 0.6mA SOP8 Reel of 2500 BA2903SF-E2 SSOP-B8 Reel of 2500 BA2903SFV-E2 MSOP8 Reel of 3000 BA2903SFVM-TR 0.8mA SOP14 Reel of 2500 BA2901SF-E2 SSOP-B14 Reel of 2500 BA2901SFV-E2 -40°C to +125°C 0.6mA SOP8 Reel of 2500 BA2903F-E2 SSOP-B8 Reel of 2500 BA2903FV-E2 MSOP8 Reel of 3000 BA2903FVM-TR 2mV SOP8 Reel of 2500 BA2903WF-E2 SSOP-B8 Reel of 2500 BA2903WFV-E2 7mV 0.8mA SOP14 Reel of 2500 BA2901F-E2 SSOP-B14 Reel of 2500 BA2901FV-E2 Absolute Maximum Ratings (Ta=25°C) Parameter Symbol Rating Unit BA8391G Supply Voltage VCC-VEE +36 V Power Dissipation PD SSOP5 0.67 (Note1,2) W Differential Input Voltage (Note 3) VID +36 V Input Common-mode Voltage Range VICM (VEE-0.3) to (VEE+36) V Input Current (Note 4) II -10 mA Operating Supply Voltage Vopr +2.0 to +36.0 (±1.0 to ±18.0) V Operating Temperature Range Topr -40 to +85 °C Storage Temperature Range Tstg -55 to +150 °C Maximum Junction Temperature Tjmax +150 °C (Note 1) To use at temperature above TA＝25°C reduce 5.4mW. (Note 2) Mounted on a FR4 glass epoxy PCB(70mm×70mm×1.6mm). (Note 3) The voltage difference between inverting input and non-inverting input is the differential input voltage. Then input terminal voltage is set to more than VEE. (Note 4) Excessive input current will flow if a differential input voltage in excess of approximately 0.6V is applied between the input unless some limiting resistance is used. Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over the absolute maximum ratings.

www.rohm.com TSZ02201-0RFR0G200200-1-2 TSZ22111 • 15 • 001 BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Se ries Absolute Maximum Ratings - continued Parameter Symbol Rating Unit BA10393F BA10339xx Supply Voltage VCC-VEE +36 V Power Dissipation PD SOP8 0.62 (Note 5,8) - W SOP14 - 0.49 (Note 6,8) SSOP-B14 - 0.70 (Note 7,8) Differential Input Voltage(Note 9) VID (VEE to VCC) V Input Common-mode Voltage Range VICM (VEE-0.3) to VCC V Input Current(Note 10) II -10 mA Operating Supply Voltage Vopr +2.0 to +36.0 (±1.0 to ±18.0) +3.0 to +36.0 (±1.5 to ±18.0) V Operating Temperature Range Topr -40 to +85 °C Storage Temperature Range Tstg -55 to +125 °C Maximum Junction Temperature Tjmax +125 °C (Note 5) To use at temperature above TA＝25°C reduce 6.2mW. (Note 6) To use at temperature above TA＝25°C reduce 4.9mW. (Note 7) To use at temperature above TA＝25°C reduce 7.0mW. (Note 8) Mounted on a FR4 glass epoxy PCB(70mm×70mm×1.6mm). (Note 9) The voltage difference between inverting input and non-inverting input is the differential input voltage. Then input terminal voltage is set to more than VEE. (Note 10) Excessive input current will flow if a differential input voltage in excess of approximately 0.6V is applied between the input unless some limiting resistance is used. Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as a dding a fuse, in case the IC is operated over the absolute maximum ratings. Parameter Symbol Rating Unit BA2903Sxxx BA2901Sxx BA2903xxx BA2901xx Supply Voltage VCC-VEE +36 V Power Dissipation PD SOP8 0.77 (Note 11,16) - 0.77 (Note 11,16) - W SSOP-B8 0.68 (Note 12,16) - 0.68 (Note 12,16) - MSOP8 0.58 (Note 13,16) - 0.58 (Note 13,16) - SOP14 - 0.61 (Note 14,16) - 0.61 (Note 14,16) SSOP-B14 - 0.87 (Note 15,16) - 0.87 (Note 15,16) Differential Input Voltage (Note 17) VID 36 V Input Common-mode Voltage Range VICM (VEE-0.3) to (VEE+36) V Input Current (Note 18) II -10 mA Operating Supply Voltage Vopr +2.0 to +36.0 (±1.0 to ±18.0) V Operating Temperature Range Topr -40 to +105 -40 to +125 °C Storage Temperature Range Tstg -55 to +150 °C Maximum Junction Temperature Tjmax +150 °C (Note 11) To use at temperature above TA＝25°C reduce 6.2mW. (Note 12) To use at temperature above TA＝25°C reduce 5.5mW. (Note 13) To use at temperature above TA＝25°C reduce 4.7mW. (Note 14) To use at temperature above TA＝25°C reduce 4.9mW. (Note 15) To use at temperature above TA＝25°C reduce 7.0mW. (Note 16) Mounted on a FR4 glass epoxy PCB(70mm×70mm×1.6mm). (Note 17) The voltage difference between inverting input and non-inverting input is the differential input voltage. Then input terminal voltage is set to more than VEE. (Note 18) Excessive input current will flow if a differential input voltage in excess of approximately 0.6V is applied between the input unless some limiting resistance is used. Caution: Operating the IC over the absolute maximum ratings may damage the I C. The damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over the absolute maximum ratings.

www.rohm.com TSZ02201-0RFR0G200200-1-2 TSZ22111 • 15 • 001 BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Se ries

Electrical Characteristics

○BA8391G(Unless otherwise specified VCC=+5V, VEE=0V, TA=25°C) Parameter Symbol Temperature Range Limit Unit Conditions Min Typ Max Input Offset Voltage (Note 19,20) VIO 25°C - 2 7 mV OUT=1.4V Full range - - 15 VCC=5 to 36V, OUT=1.4V Input Offset Current (Note 19,20) IIO 25°C - 5 50 nA OUT=1.4V Full range - - 200 Input Bias Current (Note 20,21) IB 25°C - 50 250 nA OUT=1.4V Full range - - 500 Input Common-mode Voltage Range VICM 25°C 0 - VCC -1.5 V - Large Signal Voltage Gain AV 25°C 25 100 - V/mV VCC=15V, OUT=1.4 to 11.4V RL=15kΩ, VRL=15V 88 100 - dB Supply Current (Note 20) ICC 25°C - 0.3 0.7 mA OUT=Open Full range - - 1.3 OUT=Open, VCC=36V Output Sink Current(Note 22) ISINK 25°C 6 16 - mA +IN=0V, -IN=1V OUT=1.5V Output Saturation Voltage (Note 20) (Low Level Output Voltage) VOL 25°C - 150 400 mV +IN= 0V, -IN=1V ISINK=4mA Full range - - 700 Output Leakage Current (Note 20) (High Level Output Current) ILEAK 25°C - 0.1 - nA +IN=1V, -IN=0V OUT=5V Full range - - 1 μA +IN=1V, -IN=0V OUT=36V Response Time tRE 25°C - 1.3 - μs RL=5.1kΩ, VRL=5V IN=100mVP-P, Overdrive=5mV - 0.4 - RL=5.1kΩ, VRL=5V, IN=TTL Logic Swing, VREF=1.4V (Note 19) Absolute value (Note 20) Full range TA=-40°C to +85°C (Note 21) Current Direction: Because the first stage is composed with PNP transistor, input bias current flows out of IC. (Note 22) Please determine the output current value in consideration of the power dissipation of the IC under high temperature environment. When the output terminal is continuously shorted, output current may be reduced by the temperature rise of the IC.

www.rohm.com TSZ02201-0RFR0G200200-1-2 TSZ22111 • 15 • 001 BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Se ries Electrical Characteristics - continued ○BA10393F (Unless otherwise specified VCC=+5V, VEE=0V, TA=25°C) Parameter Symbol Temperature Range Limit Unit Conditions Min Typ Max Input Offset Voltage (Note 23) VIO 25°C - 1 5 mV OUT=1.4V Input Offset Current (Note 23) IIO 25°C - 5 50 nA OUT=1.4V Input Bias Current (Note 24) IB 25°C - 50 250 nA OUT=1.4V Input Common-mode Voltage Range VICM 25°C 0 - VCC -1.5 V - Large Signal Voltage Gain AV 25°C 50 200 - V/mV VCC=15V, OUT=1.4 ~ 11.4V RL=15kΩ, VRL=15V 94 106 - dB Supply Current ICC 25°C - 0.4 1 mA RL=∞, All Comparators Output Sink Current (Note 25) ISINK 25°C 6 16 - mA -IN=1V, +IN=0V OUT=1.5V Output Saturation Voltage (Low Level Output Voltage) VOL 25°C - 250 400 mV -IN=1V, +IN=0V ISINK=4mA Output Leakage Current (High Level Output Current) ILEAK 25°C - 0.1 - nA -IN=0V, +IN=1V OUT=5V 25°C - - 1 μA -IN=0V, +IN=1V OUT=36V Response Time tRE 25°C - 1.3 - μs RL=5.1kΩ, VRL=5V IN=100mVP-P, Overdrive=5mV - 0.4 - RL=5.1kΩ, VRL=5V, IN=TTL Logic Swing, VREF=1.4V (Note 23) Absolute value (Note 24) Current Direction: Because the first stage is composed with PNP transistor, input bias current flows out of IC. (Note 25) Please determine the output current value in consideration of the power dissipation of the IC under high temperature environm ent. When the output terminal is continuously shorted, output current may be reduced by the temperature rise of the IC. ○BA10339 xx(Unless otherwise specified VCC=+5V, VEE=0V, TA=25°C) Parameter Symbol Temperature Range Limit Unit Conditions Min Typ Max Input Offset Voltage (Note 26) VIO 25°C - 1 5 mV OUT=1.4V Input Offset Current (Note 26) IIO 25°C - 5 50 nA OUT=1.4V Input Bias Current (Note 27) IB 25°C - 50 250 nA OUT=1.4V Input Common-mode Voltage Range VICM 25°C 0 - VCC -1.5 V - Large Signal Voltage Gain AV 25°C 50 200 - V/mV VCC=15V, OUT=1.4 ~ 11.4V RL=15kΩ, VRL=15V 94 106 - dB Supply Current ICC 25°C - 0.8 2 mA RL=∞, All Comparators Output Sink Current(Note 28) ISINK 25°C 6 16 - mA -IN=1V, +IN=0V OUT=1.5V Output Saturation Voltage (Low Level Output Voltage) VOL 25°C - 250 400 mV -IN=1V, +IN=0V ISINK=4mA Output Leakage Current (High Level Output Current) ILEAK 25°C - 0.1 - nA -IN=0V, +IN=1V OUT=5V 25°C - - 1 μA -IN=0V, +IN=1V OUT=36V Response Time tRE 25°C - 1.3 - μs RL=5.1kΩ, VRL=5V IN=100mVP-P, Overdrive=5mV - 0.4 - RL=5.1kΩ, VRL=5V, IN=TTL Logic Swing, VREF=1.4V (Note 26) Absolute value (Note 27) Current Direction: Because the first stage is composed with PNP transistor, input bias current flows out of IC. (Note 28) Please determine the output current value in consideration of the power dissipation of the IC under high temperature environm ent. When the output terminal is continuously shorted, output current may be reduced by t he temperature rise of the IC.

www.rohm.com TSZ02201-0RFR0G200200-1-2 TSZ22111 • 15 • 001 BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Se ries Electrical Characteristics - continued ○BA2903xxx, BA2903S xxx(Unless otherwise specified VCC=+5V, VEE=0V, TA=25°C) Parameter Symbol Temperature Range Limit Unit Conditions Min Typ Max Input Offset Voltage (Note 29,30) VIO 25°C - 2 7 mV OUT=1.4V Full range - - 15 VCC=5 to 36V, OUT=1.4V Input Offset Current (Note 29,30) IIO 25°C - 5 50 nA OUT=1.4V Full range - - 200 Input Bias Current (Note 30,31) IB 25°C - 50 250 nA OUT=1.4V Full range - - 500 Input Common-mode Voltage Range VICM 25°C 0 - VCC -1.5 V - Large Signal Voltage Gain AV 25°C 25 100 - V/mV VCC=15V, OUT=1.4 to 11.4V RL=15kΩ, VRL=15V 88 100 - dB Supply Current (Note 30) ICC 25°C - 0.6 1 mA OUT=Open Full range - - 2.5 OUT=Open, VCC=36V Output Sink Current(Note 32) ISINK 25°C 6 16 - mA +IN=0V, -IN=1V OUT=1.5V Output Saturation Voltage(Note 30) (Low Level Output Voltage) VOL 25°C - 150 400 mV +IN=0V, -IN= 1V ISINK=4mA Full range - - 700 Output Leakage Current (Note 30) (High Level Output Current) ILEAK 25°C - 0.1 - nA +IN=1V, -IN=0V OUT=5V Full range - - 1 μA +IN=1V, -IN=0V OUT=36V Response Time tRE 25°C - 1.3 - μs RL=5.1kΩ, VRL=5V IN=100mVP-P, Overdrive=5mV - 0.4 - RL=5.1kΩ, VRL=5V, IN=TTL Logic Swing, VREF=1.4V (Note 29) Absolute value (Note 30) BA2903S : Full range -40°C to +105°C, BA2903: Full range -40°C to +125°C (Note 31) Current Direction: Because the first stage is composed with PNP transistor, input bias current flows out of IC. (Note 32) Please determine the output current value in consideration of the power dissipation of the IC under high temperature environment. When the output terminal is continuously shorted, output current may be reduced by the temperature rise of the IC.

www.rohm.com TSZ02201-0RFR0G200200-1-2 TSZ22111 • 15 • 001 BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Se ries Electrical Characteristics - continued ○BA2903Wxx (Unless otherwise specified VCC=+5V, VEE=0V, TA=25°C) Parameter Symbol Temperature Range Limit Unit Conditions Min Typ Max Input Offset Voltage (Note 33) VIO 25°C - 0.5 2 mV OUT=1.4V Input Offset Current (Note 33) IIO 25°C - 5 50 nA OUT=1.4V Input Bias Current (Note 34,35) IB 25°C - 50 250 nA OUT=1.4V Full range - - 500 Input Common-mode Voltage Range VICM 25°C 0 - VCC -1.5 V - Large Signal Voltage Gain AV 25°C 25 100 - V/mV VCC=15V, OUT=1.4 to 11.4V RL=15kΩ, VRL=15V 88 100 - dB Supply Current (Note 34) ICC 25°C - 0.6 1 mA OUT=Open Full range - - 2.5 OUT=Open, VCC=36V Output Sink Current (Note 36) ISINK 25°C 6 16 - mA +IN=0V, -IN=1V OUT=1.5V Output Saturation Voltage(Note 34) (Low Level Output Voltage) VOL 25°C - 150 400 mV +IN=0V, -IN= 1V ISINK=4mA Full range - - 700 Output Leakage Current (Note 34) (High Level Output Current) ILEAK 25°C - 0.1 - nA +IN=1V, -IN=0V OUT=5V Full range - - 1 μA +IN=1V, -IN=0V OUT=36V Response Time tRE 25°C - 1.3 - μs RL=5.1kΩ, VRL=5V IN=100mVP-P, Overdrive=5mV - 0.4 - RL=5.1kΩ, VRL=5V, IN=TTL Logic Swing, VREF=1.4V (Note 33) Absolute value (Note 34) BA2903W: Full range -40°C to +125°C (Note 35) Current Direction: Because the first stage is composed with PNP transistor, input bias current flows out of IC. (Note 36) Please determine the output current value in consideration of the power dissipation of the IC under high temperature environment. When the output terminal is continuously shorted, output current may be reduced by the temperature rise of the IC.

www.rohm.com TSZ02201-0RFR0G200200-1-2 TSZ22111 • 15 • 001 BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Se ries Electrical Characteristics - continued ○BA2901xx, BA2901S xx(Unless otherwise specified VCC=+5V, VEE=0V, Ta=25°C) Parameter Symbol Temperature Range Limit Unit Conditions Min Typ Max Input Offset Voltage (Note 37,38) VIO 25°C - 2 7 mV OUT=1.4V Full range - - 15 VCC=5 to 36V, OUT=1.4V Input Offset Current (Note 37,38) IIO 25°C - 5 50 nA OUT=1.4V Full range - - 200 Input Bias Current (Note 38,39) IB 25°C - 50 250 nA OUT=1.4V Full range - - 500 Input Common-mode Voltage Range VICM 25°C 0 - VCC-1.5 V - Large Signal Voltage Gain AV 25°C 25 100 - V/mV VCC=15V, OUT=1.4 to 11.4V RL=15kΩ, VRL=15V 88 100 - dB Supply Current (Note 38) ICC 25°C - 0.8 2 mA OUT=Open Full range - - 2.5 OUT=Open, VCC=36V Output Sink Current(Note 40) ISINK 25°C 6 16 - mA +IN=0V, VIN=1V OUT=1.5V Output Saturation Voltage(Note 38) (Low Level Output Voltage) VOL 25°C - 150 400 mV +IN=0V, -IN=1V ISINK=4mA Full range - - 700 Output Leakage Current (Note 38) (High Level Output Current) ILEAK 25°C - 0.1 - nA +IN=1V, -IN=0V OUT=5V Full range - - 1 μA +IN=1V, -IN=0V OUT=36V Response Time tRE 25°C - 1.3 - μs RL=5.1kΩ, VRL=5V VIN=100mVP-P, Overdrive=5mV - 0.4 - RL=5.1kΩ, VRL=5V, VIN=TTL Logic Swing, VREF=1.4V (Note 37) Absolute value (Note 38) BA2901S：Full range -40°C to 105°C ,BA2901：Full range -40°C to +125°C (Note 39) Current Direction : Because the first stage is composed with PNP transistor, input bias current flows out of IC. (Note 40) Please determine the output current value in consideration of t he power dissipation of the IC under high temperature environment. When the output terminal is continuously shorted, output current may be reduced by the temperature rise of the IC.

www.rohm.com TSZ02201-0RFR0G200200-1-2 TSZ22111 • 15 • 001 BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Se ries Description of electrical characteristics Described below are descriptions of the relevant electric al terms used in this datasheet . Items and symbols used are also shown. Note that item name and symbol and their meaning may differ from those on another manufacturer’s document or general document. 1. Absolute maximum ratings Absolute maximum rating items indicate the condition which must not be exceeded. Application of voltage in excess of absolute maximum rating or use out of absolute maximum rated temperature environment may cause deterioration of characteristics. (1) Power supply voltage (VCC/VEE) Indicates the maximum voltage that can be applied between the positive power supply terminal and negative power supply terminal without deterioration or destruction of characteristics of internal circuit. (2) Differential input voltage (VID) Indicates the maximum voltage that can be applied between non-inverting and inverting terminals without damaging the IC. (3) Input common-mode voltage range (VICM) Indicates the maximum voltage that can be applied to the non-inverting and inverting terminals without deter ioration or destruction of electrical characteristics. Input common-mode voltage range of the maximum ratings does not assure normal operation of IC. For normal operation, use the IC within the input common-mode voltage range characteristics. (4) Power dissipation (Pd) Indicates the power that can be consumed by the IC when mounted on a specific board at the ambient temperature 25°C (normal temperature). As for package product, Pd is determined by the temperature that can be permitted by the IC in the package (maximum junction temperature) and the thermal resistance of the package. 2. Electrical characteristics (1) Input offset voltage (VIO) Indicates the voltage difference between non- inverting terminal and inverting terminals. It can be translated into th e input voltage difference required for setting the output voltage at 0 V. (2) Input offset current (IIO) Indicates the difference of input bias current between the non-inverting and inverting terminals. (3) Input bias current (IB) Indicates the current t hat flows into or out of the input terminal. It is defined by the average of input bias currents at the non-inverting and inverting terminals. (4) Input common-mode voltage range (VICM) Indicates the input voltage range where IC normally operates. (5) Large signal voltage gain (AV) Indicates the amplifying rate (gain) of output voltage against the voltage difference between non-inverting terminal and inverting terminal. It is normally the amplifying rate (gain) with reference to DC voltage. Av = (Output voltage) / (Differential Input voltage) (6) Supply current (ICC) Indicates the current that flows within the IC under specified no-load conditions. (7) Output sink current (ISINK) Denotes the maximum current that can be output under specific output conditions. (8) Output saturation voltage, low level output voltage (VOL) Signifies the voltage range that can be output under specific output conditions. (9) Output leakage current, High level output current (ILEAK) Indicates the current that flows into the IC under specific input and output conditions. (10) Response time (tRE) Response time indicates the delay time between the input and output signal is determined by the time difference from the fifty percent of input signal swing to the fifty percent of output signal swing.

www.rohm.com TSZ02201-0RFR0G200200-1-2 TSZ22111 • 15 • 001 BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Se ries

Application Information

NULL method condition for Test Circuit1 VCC, VEE, EK, VICM Unit : V, VRL=VCC Parameter VF S1 S2 S3 BA10393 / BA10339 BA8391 / BA2903 / BA2901 Calculation VCC VEE EK VICM VCC VEE EK VICM Input Offset Voltage VF1 ON ON ON 5 0 -1.4 0 5 to 36 0 -1.4 0 1 Input Offset Current VF2 OFF OFF ON 5 0 -1.4 0 5 0 -1.4 0 2 Input Bias Current VF3 OFF ON ON 5 0 -1.4 0 5 0 -1.4 0 3 VF4 ON OFF 5 0 -1.4 0 5 0 -1.4 0 Large Signal Voltage Gain VF5 ON ON ON 15 0 -1.4 0 15 0 -1.4 0 4 VF6 15 0 -11.4 0 15 0 -11.4 0 - Calculation - 1. Input Offset Voltage (VIO) 2. Input Offset Current (I IO) 3. Input Bias Current (I 4. Large Signal Voltage Gain (A Figure 111. Test Circuit1 (One Channel Only)

www.rohm.com TSZ02201-0RFR0G200200-1-2 TSZ22111 • 15 • 001 BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Se ries Example of Circuit ○Reference voltage is VIN- While input voltage is bigger than reference voltage, output voltage is high. While input voltage is smaller than reference voltage, output voltage is low. ○Reference voltage is V IN+ While input voltage is smaller than reference voltage, output voltage is high. While input voltage is bigger than reference voltage, output voltage is low. Reference voltage Vref IN VCC VEE VRL RL OUT -Vref VEE VCC VRL RL Reference voltage IN Time Vref OUT Time High Low Time Vref Low High Time IN OUT

www.rohm.com TSZ02201-0RFR0G200200-1-2 TSZ22111 • 15 • 001 BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Se ries Operational Notes 1. Reverse Connection of Power Supply Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when connecting the power supply, such as mounting an external diode between the power supply and the IC’s power supply terminals. 2. Power Supply Lines Design the PCB layout pattern to provide low impedance ground and supply lines. Separate the ground and supply lines of the digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affect ing the analog block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and aging on the capacitance value when using electrolytic capacitors. 3. Ground Voltage Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition. 4. Ground Wiring Pattern When using both small-signal and large-current ground traces, the two ground traces should be routed separately but connected to a single ground at the reference point of the application board to avoid fluctuations in the small -signal ground caused by large currents. Also ensure that the ground traces of external components do not cause variations on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance. 5. Thermal Consideration Should by any chance the power dissipation rating be exceeded, the rise in temperature of the chip may result in deterioration of the properties of the chip. In case of exceeding this absolute maximum rating, increase the board size and copper area to prevent exceeding the Pd rating. 6. Recommended Operating Conditions These conditions represent a range within which the expected characteristics of the IC can be approximately obtained. The electrical characteristics are guaranteed under the conditions of each parameter. 7. Inrush Current When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power supply. Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing of connections. 8. Operation Under Strong Electromagnetic Field Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction. 9. Testing on Application Boards When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply should always be turned off completely before connecting or removing it from the test setup during the inspection process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during transport and storage. 10. Inter-pin Short and Mounting Errors Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in damaging the IC. Avoid nearby pins being shorted to each other especially to ground. Inter -pin shorts could be due to many r easons such as metal particles, water droplets (in very humid environment) and unintentional solder bridge deposited in between pins during assembly to name a few.

www.rohm.com TSZ02201-0RFR0G200200-1-2 TSZ22111 • 15 • 001 BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Se ries Physical Dimension Tape and Reel Information

www.rohm.com TSZ02201-0RFR0G200200-1-2 TSZ22111 • 15 • 001 BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Se ries Physical Dimension Tape and Reel Information - continued (UNIT : mm) PKG : SOP8 Drawing No. : EX112-5001-1 (Max 5.35 (include.BURR))

www.rohm.com TSZ02201-0RFR0G200200-1-2 TSZ22111 • 15 • 001 BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Se ries Physical Dimension Tape and Reel Information - continued Package Name SSOP-B8

www.rohm.com TSZ02201-0RFR0G200200-1-2 TSZ22111 • 15 • 001 BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Se ries Physical Dimension Tape and Reel Information - continued

www.rohm.com TSZ02201-0RFR0G200200-1-2 TSZ22111 • 15 • 001 BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Se ries Physical Dimension Tape and Reel Information - continued (UNIT : mm) PKG : SOP14 Drawing No. : EX113-5001 (Max 9.05 (include.BURR))

www.rohm.com TSZ02201-0RFR0G200200-1-2 TSZ22111 • 15 • 001 BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Se ries Physical Dimension Tape and Reel Information - continued Package Name SSOP-B14

www.rohm.com TSZ02201-0RFR0G200200-1-2 TSZ22111 • 15 • 001 BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Se ries Marking Diagrams Product Name Package Type Marking BA8391 G SSOP5 D6 BA10393 F SOP8 10393 BA10339 F SOP14 BA10339F FV SSOP-B14 339 BA2903 F SOP8 2903 FV SSOP-B8 FVM MSOP8 BA2903W F SOP8 FV SSOP-B8 BA2903S F SOP8 2903S FV SSOP-B8 03S FVM MSOP8 2903S BA2901 F SOP14 BA2901F FV SSOP-B14 2901 BA2901S F SOP14 2901S FV SSOP-B14 SOP8 (TOP VIEW) Part Number Marking LOT Number 1PIN MARK SOP14 (TOP VIEW) Part Number Marking LOT Number 1PIN MARK SSOP-B8 (TOP VIEW) Part Number Marking LOT Number 1PIN MARK SSOP-B14 (TOP VIEW) Part Number Marking LOT Number 1PIN MARK MSOP8 (TOP VIEW) Part Number Marking LOT Number 1PIN MARK Part Number Marking SSOP5(TOP VIEW) LOT Number

www.rohm.com TSZ02201-0RFR0G200200-1-2 TSZ22111 • 15 • 001 BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Se ries e MIE e Land Pattern Data All dimensions in mm PKG Land Pitch e Land Space MIE Land Length ≧ℓ 2 Land Width SSOP5 0.95 2.4 1.0 0.6 SOP8 SOP14 1.27 4.60 1.10 0.76 SSOP-B8 SSOP-B14 0.65 4.60 1.20 0.35 MSOP8 0.65 2.62 0.99 0.35

Revision History

23.Aug.2013 001 New Release 27.Nov.2013 002 Add the dB notation in Large Signal Voltage Gain 11.Dec.2013 003 Input offset voltage unit is changed from mA to mV in Page.1. 05.Jun.2015 004 Corrections. Update of Operational Notes SSOP5 SOP8, SOP14, SSOP-B8 SSOP-B14, MSOP8 MIE ℓ 2 b 2 e

Notice-PGA-E Rev.001 © 2015 ROHM Co., Ltd. All rights reserved. Notice Precaution on using ROHM Products 1. Our Products are designed and manufac tured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electroni c appliances, amusement equipment, etc.). If you intend to use our Products in devices requiring ex tremely high reliability (such as medical equipment (Note 1), transport equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sale s representative in advance. Unless otherwise agreed in writing by ROHM in advance, RO HM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅣ CLASS Ⅲ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe desi gn against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditio ns, as exemplified below. Accordin gly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of an y ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified bel ow), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products ar e exposed to sea wind or corrosive gases, including Cl 2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (ev en if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subjec t to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short per iod of time, such as pulse. is applied, confirmation of performance characteristics after on-boar d mounting is strongly recomm ended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temper ature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperat ure is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for fa ilure induced under deviant condi tion from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlori ne, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be us ed on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow sol dering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification

Notice-PGA-E Rev.001 © 2015 ROHM Co., Ltd. All rights reserved. Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, pl ease allow a sufficient margin c onsidering variations of the characteristics of the Products and external components, including transient characteri stics, as well as static characteristics. 2. You agree that application notes, re ference designs, and associated data and in formation contained in this document are presented only as guidance for Products use. Theref ore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding t he Products maximum rating will not be applied to Products. Please take special care under dry condit ion (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriora te if the Products are stored in the places where: [a] the Products are exposed to sea winds or corros ive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to di rect sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage c ondition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm sol derability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the co rrect direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a hum idity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign trade act, please consult with ROHM in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contain ed in this document is for reference only. ROHM does not warrant that foregoi ng information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. ROHM shall not have any obligations where the claims, actions or demands arising from the co mbination of the Products with other articles such as components, circuits, systems or external equipment (including software). 3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. Other Precaution 1. This document may not be reprinted or reproduced, in whol e or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any wa y whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, incl uding but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties.

Notice – WE Rev.001 © 2015 ROHM Co., Ltd. All rights reserved. General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for failure, malfunction or acci dent arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ec t to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or concerning such information.

Minimum Package Quantity 2500 Packing Type Taping Constitution Materials List inquiry RoHS Yes BA10339F - Web Page Distribution Inventory