ATV212HD30N4 SCHNEIDER

Document overview

  • PDF pages: 11

Technical content

Page 1

Characteristics

PDF page 1 diagram

Main

type

tion

age

Complementary

Apparent power Prospective line Isc Continuous output current

Maximum transient current Speed drive output frequency Nominal switching frequency Switching frequency

Speed range Speed accuracy Torque accuracy Transient overtorque Asynchronous motor control profile

Regulation loop Motor slip compensation

Local signalling Output voltage Isolation Type of cable

Aug 9, 2019

variable speed drive ATV212 - 30kW - 40hp -

480V - 3ph - EMC - IP21

Product availability: Stock - Normally stocked in distribution facility

Range of product

Altivar 212

Product or component

Variable speed drive

Device short name

ATV212

Product destination

Asynchronous motors

Product specific applica-

Pumps and fans in HVAC

Assembly style

With heat sink

Phase

3 phases

Motor power kW

30 kW

Motor power hp

40 hp

[Us] rated supply volt-

380...480 V - 15...10 %

Supply voltage limits

323...528 V

Supply frequency

50...60 Hz - 5...5 %

Network frequency

47.5...63 Hz

EMC filter

Class C2 EMC filter integrated

Line current

44.7 A 480 V 56.7 A 380 V

44.6 kVA 380 V 22 kA 58.5 A 380 V 58.5 A 460 V 64.4 A 60 s 0.5...200 Hz 8 kHz 6...16 kHz adjustable 8...16 kHz with derating factor 1...10 +/- 10 % of nominal slip 0.2 Tn to Tn +/- 15 % 120 % of nominal motor torque +/- 10 % 60 s Voltage/Frequency ratio, 2 points Voltage/Frequency ratio, 5 points Flux vector control without sensor, standard Voltage/Frequency ratio - Energy Saving, quadratic U/f Voltage/frequency ratio, automatic IR compensation (U/f + automatic Uo) Adjustable PI regulator Adjustable Automatic whatever the load Not available in voltage/frequency ratio motor control 1 LED red DC bus energized <= power supply voltage Electrical between power and control

IEC cable without mounting kit 1 113 °F (45 °C) copper 90 °C XLPE/EPR IEC cable without mounting kit 1 45 °C copper 70 °C PVC UL 508 cable with UL Type 1 kit 3 40 °C copper 75 °C PVC

Page 2

Terminal 0 in² (2.5 mm²) AWG 14 VIA, VIB, FM, FLA, FLB, FLC, RY, RC, F, R,

Electrical connection

RES Terminal 50 mm² AWG 1/0 L1/R, L2/S, L3/T 212.39 lbf.in (24 N.m) 212 lb.in L1/R, L2/S, L3/T

Tightening torque

0.6 N.m VIA, VIB, FM, FLA, FLB, FLC, RY, RC, F, R, RES Internal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC +/- 5 % <=

Supply

10 A overload and short-circuit protection Internal supply 24 V DC 21...27 V <= 200 A overload and short-circuit protection

Analogue input number

2 Switch-configurable voltage VIA 0...10 V DC 24 V max 30000 Ohm 10 bits

Analogue input type

Configurable voltage VIB 0...10 V DC 24 V max 30000 Ohm 10 bits Configurable PTC probe VIB 0...6 probes 1500 Ohm Switch-configurable current VIA 0...20 mA 250 Ohm 10 bits 2 ms +/- 0.5 ms F discrete

Sampling duration

2 ms +/- 0.5 ms R discrete 2 ms +/- 0.5 ms RES discrete 3.5 ms +/- 0.5 ms VIA analog 22 ms +/- 0.5 ms VIB analog 2 ms +/- 0.5 ms FM analog

Response time

7 ms +/- 0.5 ms FLA, FLC discrete 7 ms +/- 0.5 ms FLB, FLC discrete 7 ms +/- 0.5 ms RY, RC discrete +/- 0.6 % VIA for a temperature variation 60 °C

Accuracy

+/- 0.6 % VIB for a temperature variation 60 °C +/- 1 % FM for a temperature variation 60 °C +/- 0.15 % of maximum value input VIA

Linearity error

+/- 0.15 % of maximum value input VIB +/- 0.2 % output FM

Analogue output number

1 Switch-configurable voltage FM 0...10 V DC 7620 Ohm 10 bits

Analogue output type

Switch-configurable current FM 0...20 mA 970 Ohm 10 bits

Discrete output number

2 Configurable relay logic FLA, FLC NO 100000 cycles

Discrete output type

Configurable relay logic FLB, FLC NC 100000 cycles Configurable relay logic RY, RC NO 100000 cycles 3 mA 24 V DC configurable relay logic

Minimum switching current

5 A 250 V AC resistive cos phi = 1 L/R = 0 ms FL, R

Maximum switching current

5 A 30 V DC resistive cos phi = 1 L/R = 0 ms FL, R 2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms FL, R 2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms FL, R Programmable F 24 V DC level 1 PLC 4700 Ohm

Discrete input type

Programmable R 24 V DC level 1 PLC 4700 Ohm Programmable RES 24 V DC level 1 PLC 4700 Ohm Positive logic (source) F, R, RES <= 5 V >= 11 V

Discrete input logic

Negative logic (sink) F, R, RES >= 16 V <= 10 V Automatic based on the load

Acceleration and deceleration ramps

Linear adjustable separately from 0.01 to 3200 s

Braking to standstill

By DC injection Motor phase break motor

Protection type

Break on the control circuit drive Thermal power stage drive Overvoltages on the DC bus drive Against exceeding limit speed drive Against input phase loss drive With PTC probes motor Input phase breaks drive Line supply overvoltage and undervoltage drive Line supply undervoltage drive Overcurrent between output phases and earth drive Overheating protection drive Short-circuit between motor phases drive Thermal protection motor 3535 V DC between earth and power terminals

Dielectric strength

5092 V DC between control and power terminals >= 1 MOhm 500 V DC for 1 minute

Insulation resistance

0.024/50 Hz analog input

Frequency resolution

0.1 Hz display unit

Page 3

Communication port protocol

APOGEE FLN BACnet LonWorks METASYS N2 Modbus

Connector type

1 RJ45 1 open style

Physical interface

2-wire RS 485

Transmission frame

RTU 9600 bps or 19200 bps

Transmission rate

8 bits, 1 stop, odd even or no configurable parity

Data format Type of polarization

No impedance

Number of addresses

1...247 Monitoring inhibitable

Communication service

Read device identification (43) Read holding registers (03) 2 words maximum Time out setting from 0.1 to 100 s Write multiple registers (16) 2 words maximum Write single register (06) Communication card LonWorks

Option card

Vertical +/- 10 degree

Operating position Width

9.45 in (240 mm) 16.54 in (420 mm)

Height Depth

8.43 in (214 mm) 58.2 lb(US) (26.4 kg)

Product weight Power dissipation in W

847 W 76611.27 Gal/hr(US) (290 m3/h)

Air flow Functionality

Mid

Specific application

HVAC

IP degree of protection

IP21 Building - HVAC : compressor for scroll

Variable speed drive application selection

Building - HVAC : fan Building - HVAC : pump 30...50 kW at 380...440 V 3 phases

Motor power range AC-3

30...50 kW at 480...500 V 3 phases Variable speed drive

Motor starter type

Environment

Conducted radio-frequency immunity test level 3 IEC 61000-4-6

Electromagnetic compatibility

Voltage dips and interruptions immunity test IEC 61000-4-11 1.2/50 µs - 8/20 µs surge immunity test level 3 IEC 61000-4-5 Electrical fast transient/burst immunity test level 4 IEC 61000-4-4 Electrostatic discharge immunity test level 3 IEC 61000-4-2 Radiated radio-frequency electromagnetic field immunity test level 3 IEC 61000-4-3

Pollution degree

3 IEC 61800-5-1 IP20 on upper part without blanking plate on cover EN/IEC 61800-5-1

IP degree of protection

IP20 on upper part without blanking plate on cover EN/IEC 60529 IP21 EN/IEC 61800-5-1 IP21 EN/IEC 60529 IP41 on upper part EN/IEC 61800-5-1 IP41 on upper part EN/IEC 60529 1 gn 13...200 Hz EN/IEC 60068-2-8

Vibration resistance

1.5 mm 3...13 Hz EN/IEC 60068-2-6 15 gn 11 ms IEC 60068-2-27

Shock resistance

Classes 3C1 IEC 60721-3-3

Environmental characteristic

Classes 3S2 IEC 60721-3-3 59.9 dB 86/188/EEC

Noise level

3280.84...9842.52 ft (1000...3000 m) limited to 2000 m for the Corner Grounded

Operating altitude

distribution network with current derating 1 % per 100 m <= 3280.84 ft (1000 m) without derating 5...95 % without condensation IEC 60068-2-3

Relative humidity

5...95 % without dripping water IEC 60068-2-3 14...104 °F (-10...40 °C) without derating

Ambient air temperature for operation

104...122 °F (> 40...50 °C) with derating factor

Page 4

-13...158 °F (-25...70 °C)

Ambient air temperature for storage

EN 55011 class A group 1

Standards

EN 61800-3 EN 61800-3 category C2 EN 61800-3 category C3 EN 61800-3 environments 1 category C1 EN 61800-3 environments 1 category C2 EN 61800-3 environments 1 category C3 EN 61800-3 environments 2 category C1 EN 61800-3 environments 2 category C2 EN 61800-3 environments 2 category C3 EN 61800-5-1 IEC 61800-3 IEC 61800-3 category C2 IEC 61800-3 category C3 IEC 61800-3 environments 1 category C1 IEC 61800-3 environments 1 category C2 IEC 61800-3 environments 1 category C3 IEC 61800-3 environments 2 category C1 IEC 61800-3 environments 2 category C2 IEC 61800-3 environments 2 category C3 IEC 61800-5-1 UL Type 1

Product certifications

CSA C-Tick NOM 117 UL

Marking

CE

Ordering and shipping details

22158 - ATV212 30 - 100 HP 460 VOLT

Category Discount Schedule

CP4D

GTIN

00785901921554

Nbr. of units in pkg.

1 68.200000000000003

Package weight(Lbs) Returnability

Y

Country of origin

CN

Offer Sustainability

Green Premium product

Sustainable offer status RoHS (date code: YYWW)

Compliant - since 1050 - Schneider Electric declaration of conformity

Schnei-

der Electric declaration of conformity Reference not containing SVHC above the threshold

REACh Product environmental profile

Available

Product end of life instructions

Available WARNING: This product can expose you to chemicals including:

California proposition 65

Lead and lead compounds, which is known to the State of California to cause can-

  • - - - - - - Substance 1

cer and birth defects or other reproductive harm. Bisphenol A (BPA), which is known to the State of California to cause birth defects

  • - - - - - - Substance 2

or other reproductive harm. For more information go to www.p65warnings.ca.gov

  • - - - - - - More information

Contractual warranty

Warranty period

18 months

Page 5

Dimensions Drawings

Dimensions

PDF page 5 diagram

Dimensions in mm

ATV212H a b c G H K Ø
D22M3X D22N4, D30N4 240 420 214 206 403 10 6
D37N4, D45N4 240 550 244 206 529 10 6

Dimensions in in.

ATV212H a b c G H K Ø
D22M3X D22N4, D30N4 9.45 16.54 8.43 8.11 15.87 0.39 0.24
D37N4, D45N4 9.45 21.65 9.60 8.11 20.83 0.39 0.24

EMC mounting plate (supplied with drive)

PDF page 5 diagram

Dimensions in mm

ATV212H b1 c1
D22M3X D22N4, D30N4 122 120
D37N4, D45N4 113 127

Dimensions in in.

ATV212H b1 c1
D22M3X D22N4, D30N4 4.80 4.72
D37N4, D45N4 4.45 5.00

Page 6

Mounting and Clearance

Mounting Recommendations

Clearance

Depending on the conditions in which the drive is to be used, its installation will require certain precautions and the use of appropriate accessories. Install the unit vertically:

  • Do not place it close to heating elements.
  • Leave sufficient free space to ensure that the air required for cooling purposes can circulate from bottom to the top of the unit.
PDF page 6 diagram

Mounting Types

Type A mounting

PDF page 6 diagram

Type B mounting

PDF page 6 diagram

Type C mounting

PDF page 6 diagram

By removing the protective blanking cover from the top of the drive, the degree of protection for the drive becomes IP21. The protective blanking cover may vary according to the drive model, see opposite.

Specific Recommendations for Mounting in an Enclosure

To help ensure proper air circulation in the drive:

  • Fit ventilation grilles.
  • Check that there is sufficient ventilation. If there is not, install a forced ventilation unit with a filter. The openings and/or fans must provide

a flow rate at least equal to that of the drive fans (refer to the product characteristics).

  • Use special filters with UL Type 12/IP54 protection.
  • Remove the blanking cover from the top of the drive.

Page 7

Sealed Metal Enclosure (IP54 Degree of Protection) The drive must be mounted in a dust and damp proof enclosure in certain environmental conditions, such as dust, corrosive gases, high humidity with risk of condensation and dripping water, splashing liquid, etc.This enables the drive to be used in an enclosure where the maximum internal temperature reaches 50°C.

Page 8

Connections and Schema

Recommended Wiring Diagram

3-Phase Power Supply

PDF page 8 diagram

A1: ATV 212 drive KM1: Contactor Q1: Circuit breaker Q2: GV2 L rated at twice the nominal primary current of T1 Q3: GB2CB05 S1, XB4 B or XB5 A pushbuttons S2: T1: 100 VA transformer 220 V secondary (1) Fault relay contacts for remote signalling of the drive status (2) Connection of the common for the logic inputs depends on the positioning of the switch (Source, PLC, Sink) (3) Reference potentiometer SZ1RV1202 NOTE: All terminals are located at the bottom of the drive. Install interference suppressors on all inductive circuits near the drive or connected on the same circuit, such as relays, contactors, solenoid valves, fluorescent lighting, etc.

Switches (Factory Settings)

Voltage/current selection for analog I/O (VIA and VIB)

Voltage/current selection for analog I/O (FM)

Selection of logic type

(1) negative logic (2) positive logic

Other Possible Wiring Diagrams

Page 9

Logic Inputs According to the Position of the Logic Type Switch

“Source” position

PDF page 9 diagram

“Sink” position

PDF page 9 diagram
“PLC” position with PLC transistor outputs
(1) PLC (1) PLC

2-wire control

PDF page 9 diagram

F: Forward R: Preset speed (2) ATV 212 control terminals

3-wire control

F: Forward R: Stop RES: Reverse (2) ATV 212 control terminals

PTC probe

PDF page 9 diagram

(2) ATV 212 control terminals (3) Motor

Analog Inputs

Voltage analog inputs

External +10 V
(2) ATV 212 control terminals (4) Speed reference potentiometer 2.2 to 10 kΩ (2) ATV 212 control terminals

Page 10

Analog input configured for current: 0-20 mA, 4-20 mA, X-Y mA

PDF page 10 diagram

(2) ATV 212 control terminals (5) Source 0-20 mA, 4-20 mA, X-Y mA

Analog input VIA configured as positive logic input (“Source” position)

(2) ATV 212 control terminals

Analog input VIA configured as negative logic input (“Sink” position)

PDF page 10 diagram

(2) ATV 212 control terminals

Page 11

Performance Curves

Derating Curves

The derating curves for the drive nominal current (In) depend on the temperature, the switching frequency and the mounting type (A, B or C). For intermediate temperatures (45°C for example), interpolate between 2 curves.

PDF page 11 diagram

X Switching frequency