ATA6663

ATA6663_14 ATMEL

Document overview

• Manufacturer or author: Provided By digicamel.com
• PDF pages: 19

Technical content

Features

• Operating range from 5V to 27V
• Baud rate up to 20Kbaud
• Improved slew rate control according to LIN specification 2.0, 2.1 and SAEJ2602-2
• Fully compatible with 3.3V and 5V devices
• Atmel® ATA6663: TXD Time-out Timer, Atmel ATA6664: No TXD Time-out Timer
• Normal and Sleep Mode
• Wake-up capability via LIN bus (90µs dominant)
• External wake-up via WAKE Pin (35µs low level)
• INH output to control an external voltage regulator or to switch the master pull-up
• Very low standby current during Sleep Mode (10µA)
• Wake-up source recognition
• Bus pin short-circuit protected versus GND and battery
• LIN input current < 2µA if VBAT is disconnected
• Overtemperature protection
• High EMC level
• Interference and damage protection according to ISO/CD 7637
• Fulfills the OEM “Hardware Requirements for LIN in Automotive Applications Rev.1.1”
• Packages: SO8, DFN8

Description

The Atmel ATA6663 is a fully integrated LIN transceiver complying with the LIN specification 2.0, 2.1 and SAEJ2602-2. The Atmel ATA6664 is an identical version, the only difference is that the TXD-dominant Time-out function is disabled so the device is able to send a static low signal to the LIN bus. It interfaces the LIN protocol handler and the physical layer. The device is designed to handle the low-speed data communication in vehicles, for example, in convenience electronics. Improved slope control at the LIN driver ensures secure data communication up to 20Kbaud. Sleep Mode guarantees minimal cur- rent consumption even in the case of a floating bus line or a short circuit on the LIN bus to GND. The ATA6663/ATA6664 feature advanced EMI and ESD performance. ATA6663/ATA6664 LIN Transceiver DATASHEET

Figure 1. Block Diagram

1 RXD Receive data output (open drain)

2 EN Enables normal mode; when the input is open or low, the device is in sleep mode

4 TXD Transmit data input; active low output (strong pull-down) after a local wake-up request

5 GND Ground, heat sink

6 LIN LIN bus line input/output

7 VS Battery supply

3ATA6663/ATA6664 [DATASHEET] 9146I–AUTO–10/14 2. Functional Description

2.1 Physical Layer Compatibility

Since the LIN physical layer is independent from higher LIN layers (e.g., the LIN protocol layer), all nodes with a LIN physical layer according to LIN2.x can be used along with LIN physical layer nodes, which are according to older versions (i.e.,

2.2 Supply Pin (V S)

Undervoltage detection is implemented to disable transmission if VS falls to a value below 5V in order to avoid false bus messages. After switching on VS, the IC switches to fail-safe mode and INHIBIT is switched on. The supply current in sleep mode is typically 10µA.

2.3 Ground Pin (GND)

The Atmel ATA6663/ATA6664 does not affect the LIN Bus in the case of a GND disconnection. It is able to handle a ground shift up to 11.5% of VS.

2.4 Bus Pin (LIN)

A low-side driver with internal current limitation and thermal shutdown, and an internal pull-up resistor are implemented as specified by LIN2.x. The voltage range is from –27V to +40V. This pin exhibits no reverse current from the LIN bus to VS, even in the case of a GND shift or VBatt disconnection. The LIN receiver thresholds are compatible to the LIN protocol specification.The fall time (from recessive to dominant) and the rise time (from dominant to recessive) are slope controlled. The output has a self-adapting short-circuit limitation: During current limitation, as the chip temperature increases, the current is reduced. Note: The internal pull-up resistor is only active in normal and fail-safe mode.

2.5 Input/Output Pin (TXD)

In Normal Mode the TXD pin is the microcontroller interface to control the state of the LIN output. TXD must be at Low- level in order to have a low LIN Bus. If TXD is high, the LIN output transistor is turned off and the Bus is in recessive state. The TXD pin is compatible to both a 3.3V or 5V supply. During fail-safe Mode, this pin is used as output and is signalling the wake- up source (see Section 2.14 “Wake-up Source Recognition” on page 8). It is current limited to < 8mA.

2.6 TXD Dominant Time-out Function (only Atmel ATA6663)

The TXD input has an internal pull-down resistor. An internal timer prevents the bus line from being driven permanently in dominant state. If TXD is forced to low longer than tDOM > 40ms, the pin LIN will be switched off (recessive mode). To reset this mode, TXD needs to be switched to high (> 10µs) before switching LIN to dominant again. Note: The ATA6664 does not provide this functionality.

2.7 Output Pin (RXD)

This pin forwards information on the state of the LIN bus to the microcontroller. LIN high (recessive) is indicated by a high level at RXD, LIN low (dominant) is reported by a low voltage at RXD. The output is an open drain, therefore, it is compatible to a 3.3V or 5V power supply. The AC characteristics are defined by a pull-up resistor of 5kΩ to 5V and a load capacitor of 20pF. The output is short-current protected. In unpowered mode (VS = 0V), RXD is switched off. For ESD protection a Zener diode with VZ = 6.1V is integrated.

2.8 Enable Input Pin (EN)

This pin controls the operation mode of the device. If EN = 1, the device is in normal mode, with the transmission path from TXD to LIN and from LIN to RXD both active. At a falling edge on EN, while TXD is already set to high, the device switches to sleep mode and transmission is not possible. In sleep mode, the LIN bus pin is connected to VS with a weak pull-up current source. The device can transmit only after being woken up (see Section 2.9, “Inhibit Output Pin (INH)” ). During sleep mode the device is still supplied from the battery voltage. The supply current is typically 10µA. The pin EN provides a pull-down resistor in order to force the transceiver into sleep mode in case the pin is disconnected.

ATA6663/ATA6664 [DATASHEET] 9146I–AUTO–10/14

2.9 Inhibit Output Pin (INH)

This pin is used to control an external voltage regulator or to switch on/off the LIN Master pull-up resistor in case the device is used in a Master node. The inhibit pin provides an internal switch towards pin VS which is protected by temperature monitoring. If the device is in normal or fail-safe mode, the inhibit high-side switch is turned on. When the device is in sleep mode, the inhibit switch is turned off, thus disabling the voltage regulator or other connected external devices. A wake-up event on the LIN bus or at pin WAKE will switch the INH pin to the VS level. After a system power-up (VS rises from zero), the pin INH switches automatically to the VS level.

2.10 Wake-up Input Pin (WAKE)

This pin is a high-voltage input used to wake-up the device from sleep mode. It is usually connected to an external switch in the application to generate a local wake-up. A pull-up current source with typically –10µA is implemented. The voltage threshold for a wake-up signal is 3V below the VS voltage with an output current of typically –3µA. If a local wake-up is not needed in the application, pin WAKE can directly be connected to pin VS.

2.11 Operation Modes

1. Normal Mode This is the normal transmitting and receiving mode. All features are available. 2. Sleep Mode In this mode the transmission path is disabled and the device is in low-power mode. Supply current from VBatt is typically 10µA. A wake-up signal from the LIN bus or via pin WAKE will be detected and will switch the device to fail-safe mode. If EN then switches to high, normal mode is activated. Input debounce timers at pin WAKE (tWAKE), LIN (tBUS) and EN (tsleep,tnom) prevent unwanted wake-up events due to automotive transients or EMI. In sleep mode the INH pin remains floating. The internal termination between pin LIN and pin V S is disabled. Only a weak pull-up current (typical 10 µA) between pin LIN and pin VS is present. Sleep mode can be activated independently from the actual level on pin LIN or WAKE. 3. Fail-safe Mode At system power-up or after a wake-up event, the device automatically switches to fail-safe mode. It switches the INH pin to a high state, to the VS level when VS exceeds 5V. LIN communication is switched off. The microcon- troller of the application will then confirm normal mode by setting the EN pin to high. Figure 2-1. Modes of Operation EN = 1 & NOT b c or d bb a EN = 0 EN = 1 Fail-Safe Mode Power-up Communication: OFF RXD: see table of Modes INH: high (INH HS switch ON) if VS > 5V Sleep ModeNormal Mode INH: high (INH HS switch ON) Communication: ON INH: high impedance (INH HS switch OFF) Communication: OFF Local wake-up event Go to sleep command a: Power-up (V S > 3V) b: VS < 5V c: Bus wake-up event d: Wake-up from wake switch (only Transceiver 2)

5ATA6663/ATA6664 [DATASHEET] 9146I–AUTO–10/14 Wake-up events from sleep mode:

• LIN bus
• EN pin
• WAKE pin
• VS undervoltage Figure 2-1 on page 4, Figure 2-2 on page 5 and Figure 2-5 on page 8 show the details of wake-up operations.

2.12 Remote Wake-up via Dominant Bus State

A voltage lower than the LIN pre-wake detection VLINL at pin LIN activates the internal LIN receiver and starts the wake-up detection timer. A falling edge at pin LIN, followed by a dominant bus level VBUSdom maintained for a certain time period (> tBUS) and a rising edge at pin LIN results in a remote wake-up request. The device switches to fail-safe mode. Pin INH is activated (switches to VS) and the internal termination resistor is switched on. The remote wake-up request is indicated by a low level at pin RXD to interrupt the microcontroller (see Figure 2-2). Figure 2-2. LIN Wake-up Waveform Diagram Table 2-1. Table of Operation Modes Mode of Operation Transceiver INH RXD LIN Fail-safe Off On, except VS < 5V High, except after wake-up Recessive Normal On On LIN depending TXD depending Sleep Off Off High ohmic Recessive Microcontroller start-up delay time Bus wake-up filtering time (tBUS) Off state Node in sleep state High or floating Low or floating Low High EN High Normal ModeRegulator wake-up time delay INH External voltage regulator EN RXD LIN bus

ATA6663/ATA6664 [DATASHEET] 9146I–AUTO–10/14 In sleep mode the device has a very low current consumption, even during short-circuits or floating conditions on the bus. A floating bus can arise if the Master pull-up resistor is missing, e.g., in case it is switched off when the LIN Master is in sleep mode or if the power supply of the Master node is switched off. To minimize the current consumption IVS during voltage levels at the LIN-pin below the LIN pre-wake threshold, the receiver is activated only for a specific time tmon. If tmon elapses while the voltage at the bus is lower than pre-wake detection low (VLINL) and higher than the LIN dominant level, the receiver is switched off again and the circuit reverts to sleep mode. The current consumption is then the result of IVSsleep plus ILINwake. If a dominant state is reached on the bus no wake-up will occur. Even if the voltage exceeds the pre-wake detection high (VLINH), the IC will remain in sleep mode (see Figure 2-3 on page 6). This means the LIN bus must be above the Pre-wake detection threshold VLINH for a few microseconds before a new LIN wake-up is possible. Figure 2-3. Floating LIN Bus During Sleep Mode IVSsleep IVSsleep IVSfail + ILINwake IVSsleep VBUSdom VLINL IVS tmon LIN Pre-wake LIN dominant state LIN BUS Mode of operation Int. Pull-up Resistor RLIN Wake-up Detection Phase off (disabled) Sleep Mode Sleep Mode

7ATA6663/ATA6664 [DATASHEET] 9146I–AUTO–10/14 If the Atmel® ATA6663/ATA6664 is in sleep mode and the voltage level at the LIN is in dominant state (VLIN < VBUSdom) for a time period exceeding tmon (during a short circuit at LIN, for example), the IC switches back to sleep mode. The VS current consumption then consists of IVSsleep plus ILINWAKE. After a positive edge at pin LIN the IC switches directly to fail-safe mode (see Figure 2-4). Figure 2-4. Short Circuit to GND on the LIN Bus During Sleep Mode

2.13 Local Wake-up via Pin WAKE

A falling edge at pin WAKE, followed by a low level maintained for a certain time period (> tWAKE), results in a local wake-up request. According to ISO7637, the wake-up time ensures that no transient creates a wake-up. The device then switches to fail-safe mode. Pin INH is activated (switches to VS) and the internal termination resistor is switched on. The local wake-up request is indicated both by a low level at pin RXD to interrupt the microcontroller and by a strong pull-down at pin TXD (see Figure 2-5). The voltage threshold for a wake-up signal is 3V below the VS voltage with an output current of typically –3µA. Even in case of a continuous low at pin WAKE it is possible to switch the IC into sleep mode via a low level at pin EN. The IC will remain in sleep mode for an unlimited time. To generate a new wake-up at pin WAKE, a high signal > 6µs is required. A negative edge then starts the wake-up filtering time again. Sleep Mode IVSsleep IVSfail + ILINwake IVSsleep VBUSdom VLINL LIN Pre-wake LIN dominant state LIN BUS IVS Mode of operation Int. Pull-up Resistor RLIN off (disabled) on (enabled) Wake-up Detection PhaseSleep Mode Fail-safe Mode tmon tmon

ATA6663/ATA6664 [DATASHEET] 9146I–AUTO–10/14 Figure 2-5. Wake-up from Wake-up Switch

2.14 Wake-up Source Recognition

The device can distinguish between a local wake-up request (pin WAKE) and a remote wake-up request (LIN bus). The wake-up source can be read at pin TXD in fail-safe mode. If an external pull-up resistor (typically 5kΩ) has been added on pin TXD to the power supply of the microcontroller, a high level indicates a remote wake-up request (weak pull-down at pin TXD), a low level indicates a local wake-up request (strong pull-down at pin TXD). The wake-up request flag (indicated at pin RXD) as well as the wake-up source flag (indicated at pin TXD) are reset immediately if the microcontroller sets pin EN to high (see Figure 2-2 on page 5 and Figure 2-5 on page 8).

2.15 Fail-safe Features

• During a short-circuit at LIN to VBAT, the output limits the output current to IBUS_LIM. Due to the power dissipation, the chip temperature exceeds Toff, and the LIN output is switched off. The chip cools down, and after a hysteresis of Thys, it switches the output on again.
• During a short-circuit from LIN to GND the IC can be switched to sleep mode, and even in this case the current consumption is lower than 45µA. When the short-circuit has elapsed, the IC starts with a remote wake-up.
• If the Atmel® ATA6663/ATA6664 is in sleep mode and a floating condition occurs on the bus, the IC switches back to sleep mode automatically. The current consumption is lower than 45µA in this case.
• The reverse current is < 2µA at pin LIN during loss of VBAT. This is the best behavior for bus systems where some slave nodes are supplied from battery or ignition.
• Pin EN provides a pull-down resistor to force the transceiver into sleep mode if EN is disconnected
• Pin RXD is set floating if VBAT is disconnected
• Pin TXD provides a pull-down resistor to provide a static low if TXD is disconnected
• After switching the IC into Normal Mode the TXD pin must be pulled to high longer than 10µs in order to activate the LIN driver. This feature prevents the bus from being driven into dominant state when the IC is switched into Normal Mode and TXD is low.
• The INH output transistor is protected by temperature monitoring Microcontroller start-up delay time Wake filtering time tWAKE Off state Node in sleep state High or floating TXD weak pull-down resistor Low or floating State change TXD strong pull-down Node in operation Weak pull-down EN High HighLow On state High Regulator wake-up time delay Wake pin INH EN TXD RXD Voltage regulator

9ATA6663/ATA6664 [DATASHEET] 9146I–AUTO–10/14 3. Absolute Maximum Ratings Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Parameters Symbol Min. Typ. Max. Unit VS - Continuous supply voltage –0.3 +40 V Wake DC and transient voltage (with 2.7kΩ serial resistor) - Transient voltage according to ISO7637 (coupling 1nF) –150 +40 +100 V V Logic pins (RXD, TXD, EN) –0.3 +5.5 V LIN - DC voltage - Transient voltage according to ISO7637 (coupling 1nF) –27 –150 +40 +100 V V INH - DC voltage –0.3 VS + 0.3 V ESD according to IBEE LIN EMC Test specification 1.0 according to IEC 61000-4-2 - Pin VS, LIN to GND - Pin WAKE (2.7kΩ serial resistor) KV KV ESD HBM according to STM5.1 with 1.5kΩ / 100pF - Pin VS, LIN, WAKE, INH to GND ±6 KV HBM ESD ANSI/ESD-STM5.1 JESD22-A114 AEC-Q100 (002) ±3 KV CDM ESD STM 5.3.1 ±750 V Machine Model ESD AEC-Q100-Rev.F (003) ±200 V Junction temperature Tj –40 +150 °C Storage temperature Tstg –55 +150 °C 4. Thermal Characteristics SO8 Parameters Symbol Min. Typ. Max. Unit Thermal resistance junction ambient RthJA 145 K/W Special heat sink at GND (pin 5) on PCB (fused lead frame to pin 5) RthJA 80 K/W Thermal shutdown Toff 150 165 180 °C Thermal shutdown hysteresis Thys 5 10 20 °C

ATA6663/ATA6664 [DATASHEET] 9146I–AUTO–10/14 5. Thermal Characteristics DFN8 Parameters Symbol Min. Typ. Max. Unit Thermal resistance junction to heat slug RthJC 10 K/W Thermal resistance junction to ambient, where heat slug is soldered to PCB according to JEDEC RthJA 50 K/W Thermal shutdown Toff 150 165 180 °C Thermal shutdown hysteresis Thys 5 10 20 °C 6. Electrical Characteristics 5V < VS < 27V, Tj = –40°C to +150°C No. Parameters Test Conditions Pin Symbol Min. Typ. Max. Unit Type*

1 VS Pin

1.1 DC voltage range nominal 7 VS 5 13.5 27 V A

1.2 Supply current in sleep mode

VLIN > VS – 0.5V VS < 14V

7 IVSsleep 10 20 µA A

Sleep mode, bus shorted to GND V LIN = 0V VS < 14V

7 IVSsleep_sc 23 45 µA A

1.3 Supply current in normal mode Bus recessive V S < 14V 7 IVSrec 0.9 1.3 mA A 1.4 Bus dominant VS < 14V Total bus load > 500Ω 7 IVSdom 1.2 2 mA A

1.5 Supply current in fail-safe mode Bus recessive

VS < 14V 7 IVSfail 0.5 1.1 mA A 1.6 VS undervoltage threshold on 7 VSth 4 4.95 V A 1.7 VS undervoltage threshold off 7 VSth 4.05 5 V A

1.8 VS undervoltage threshold

hysteresis 7 VSth_hys 50 500 mV A

2 RXD Output Pin (Open Drain)

2.1 Low-level output sink current Normal mode

VLIN = 0V, VRXD = 0.4V 1 IRXDL 1.3 2.5 8 mA A 2.2 RXD saturation voltage 5-kΩ pull-up resistor to 5V 1 VsatRXD 0.4 V A

2.3 High-level leakage current Normal mode

VLIN = VBAT, VRXD = 5V 1 IRXDH –3 +3 µA A 2.4 ESD Zener diode IRXD = 100µA 1 VZRXD 5.8 8.6 V A

3 TXD Input Pin

3.1 Low-level voltage input 4 VTXDL –0.3 +0.8 V A 3.2 High-level voltage input 4 VTXDH 2 5.5 V A

3.3 Pull-down resistor VTXD = 5V 4 RTXD 125 250 600 kΩ A

3.4 Low-level leakage current VTXD = 0V 4 ITXD_leak –3 +3 µA A

*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter

11ATA6663/ATA6664 [DATASHEET] 9146I–AUTO–10/14

3.5 Low-level output sink current

Fail-safe mode, local wake-up VTXD = 0.4V VLIN = VBAT 4 ITXD 1.3 2.5 8 mA A

4 EN Input Pin

4.1 Low-level voltage input 2 VENL –0.3 +0.8 V A 4.2 High-level voltage input 2 VENH 2 5.5 V A

4.3 Pull-down resistor VEN = 5V 2 REN 125 250 600 kΩ A

4.4 Low-level input current VEN = 0V 2 IEN –3 +3 µA A

5 INH Output Pin

5.1 High-level voltage Normal or fail-safe mode

IINH = –15mA 8 VINHH VS –

0.75 VS V A

5.2 Switch-on resistance between

Normal or fail-safe mode 8 RINH 30 50 Ω A

5.3 Leakage current Sleep mode

VINH = 0V/27V, VS = 27V 8 IINHL –3 +3 µA A

6 WAKE Pin

6.1 High-level input voltage 3 VWAKEH

VS – VS + 0.3V V A

6.2 Low-level input voltage IWAKE = typically –3µA 3 VWAKEL –1V VS –

3.3V V A

6.3 Wake pull-up current VS < 27V 3 IWAKE –30 –10 µA A

6.4 High-level leakage current VS = 27V, VWAKE = 27V 3 IWAKE –5 +5 µA A

7 LIN Bus Driver

7.1 Driver recessive output voltage RLOAD = 500Ω /1 kΩ 6 VBUSrec

0.9 × VS VS V A

7.2 Driver dominant voltage

VBUSdom_DRV_LoSUP VVS = 7V, Rload = 500Ω 6 V_LoSUP 1.2 V A

7.3 Driver dominant voltage

VBUSdom_DRV_HiSUP VVS = 18V, Rload = 500Ω 6 V_HiSUP 2 V A

7.4 Driver dominant voltage

VBUSdom_DRV_LoSUP VVS = 7V, Rload = 1000Ω 6 V_LoSUP_1k 0.6 V A

7.5 Driver dominant voltage

VBUSdom_DRV_HiSUP VVS = 18V, Rload = 1000Ω 6 V_HiSUP_1k_ 0.8 V A

7.6 Pull-up resistor to VS The serial diode is mandatory 6 RLIN 20 30 47 kΩ A

7.7 Voltage drop at the serial diodes In pull-up path with Rslave

ISerDiode = 10mA 6 VSerDiode 0.4 1.0 V D

7.8 LIN current limitation

VBUS = VBAT_max

6 IBUS_LIM 40 120 200 mA A

7.9 Input leakage current at the receiver, including pull-up resistor as specified Input leakage current Driver off V BUS = 0V, VS = 12V

6 IBUS_PAS_do

m –1 mA A 6. Electrical Characteristics (Continued) 5V < VS < 27V, Tj = –40°C to +150°C No. Parameters Test Conditions Pin Symbol Min. Typ. Max. Unit Type* *) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter

ATA6663/ATA6664 [DATASHEET] 9146I–AUTO–10/14

7.10 Leakage current LIN recessive

8V < VBAT < 18V 8V < VBUS < 18V VBUS ≥ VBAT

6 IBUS_PAS_rec 10 20 µA A

7.11 Leakage current at ground loss; control unit disconnected from ground; loss of local ground must not affect communication in the residual network GNDDevice = VS VBAT =12V 0V < VBUS < 18V 6 IBUS_NO_Gnd –10 +0.5 +10 µA A 7.12 Leakage current at loss of battery; node has to substain the current that can flow under this condition; bus must remain operational under this condition VBAT disconnected VSUP_Device = GND 0V < VBUS < 18V 6 IBUS_NO_Bat 0.1 2 µA A

7.13 Capacitance on pin LIN to GND 6 CLIN 20 pF D

8 LIN Bus Receiver

8.1 Center of receiver threshold VBUS_CNT =

(Vth_dom + Vth_rec)/2 6 VBUS_CNT 0.475 × VS 0.5 × VS 0.525 × VS V A 8.2 Receiver dominant state VEN = 5V 6 VBUSdom –27 0.4 × VS V A

8.3 Receiver recessive state VEN = 5V 6 VBUSrec

0.6 × VS

40 V A

8.4 Receiver input hysteresis VHYS = Vth_rec – Vth_dom 6 VBUShys

0.028 × VS 0.1 × VS 0.175 × VS V A

8.5 Pre-wake detection LIN

High-level input voltage 6 VLINH VS – VS + 0.3V V A

8.6 Pre-wake detection LIN

Low-level input voltage Switches the LIN receiver on 6 VLINL –27V VS – 3.3V V A

8.7 LIN Pre-wake pull-up current VS < 27V

VLIN = 0V 6 ILINWAKE –30 –10 µA A

9 Internal Timers

9.1 Dominant time for wake-up via

VLIN = 0V 6 tBUS 30 90 150 µs A

9.2 Time of low pulse for wake-up

via pin WAKE VWAKE = 0V 3 tWAKE 7 35 50 µs A 9.3 Time delay for mode change from fail-safe mode to normal mode via pin EN VEN = 5V 2 tnorm 2 7 15 µs A 9.4 Time delay for mode change from normal mode into sleep mode via pin EN VEN = 0V 2 tsleep 7 15 24 µs A

9.5 Atmel ATA6663:

TXD dominant time out time VTXD = 0V 4 tdom 40 60 85 ms A 9.6 Power-up delay between VS = 5V until INH switches to high VVS = 5V 7, 8 tVS 200 µs A 6. Electrical Characteristics (Continued) 5V < VS < 27V, Tj = –40°C to +150°C No. Parameters Test Conditions Pin Symbol Min. Typ. Max. Unit Type* *) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter

13ATA6663/ATA6664 [DATASHEET] 9146I–AUTO–10/14

9.7 Monitoring time for wake-up via

LIN bus 6 tmon 6 10 15 ms A LIN Bus Driver AC Parameter with Different Bus Loads Load 1 (small): 1nF, 1kΩ ; Load 2 (large): 10nF, 500Ω ; RRXD = 5kΩ ; CRXD = 20pF; Load 3 (medium): 6.8nF, 660Ω characterized on samples; 10.1 and 10.2 specifies the timing parameters for proper operation at 20Kbit/s, 10.3 and 10.4 at 10.4Kbit/s.

10.1 Duty cycle 1

THRec(max) = 0.744 × VS THDom(max) = 0.581 × VS VS = 7.0V to 18V tBit = 50µs D1 = tbus_rec(min) /( 2 × tBit) 6 D1 0.396 A

10.2 Duty cycle 2

THRec(min) = 0.422 × VS THDom(min) = 0.284 × VS VS = 7.0V to 18V tBit = 50µs D2 = tbus_rec(max) /( 2 × tBit) 6 D2 0.581 A

10.3 Duty cycle 3

THRec(max) = 0.778 × VS THDom(max) = 0.616 × VS VS = 7.0V to 18V tBit = 96µs D3 = tbus_rec(min) /( 2 × tBit) 6 D3 0.417 A

10.4 Duty cycle 4

THRec(min) = 0.389 × VS THDom(min) = 0.251 × VS VS = 7.0V to 18V tBit = 96µs D4 = tbus_rec(max) /( 2 × tBit) 6 D4 0.590 A

11 Receiver Electrical AC Parameters of the LIN Physical Layer

LIN receiver, RXD load conditions: CRXD = 20pF, Rpull-up = 5kΩ

11.1 Propagation delay of receiver

(see Figure 6-1 on page 14) trec_pd = max(trx_pdr , trx_pdf) VS = 7.0V to 18V 1 trx_pd 6 µs A 11.2 Symmetry of receiver propagation delay rising edge minus falling edge trx_sym = trx_pdr – trx_pdf VS = 7.0V to 18V 1 trx_sym –2 +2 µs A 6. Electrical Characteristics (Continued) 5V < VS < 27V, Tj = –40°C to +150°C No. Parameters Test Conditions Pin Symbol Min. Typ. Max. Unit Type* *) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter

ATA6663/ATA6664 [DATASHEET] 9146I–AUTO–10/14 Figure 6-1. Definition of Bus Timing Parameter TXD (Input to transmitting node) VS (Transceiver supply of transmitting node) RXD (Output of receiving node 1) RXD (Output of receiving node 2) LIN Bus Signal Thresholds of receiving node 1 Thresholds of receiving node 2 tBus_rec(max) trx_pdr(1) trx_pdf(2)trx_pdr(2) trx_pdf(1) tBus_dom(min) tBus_dom(max) THRec(max) THDom(max) THRec(min) THDom(min) tBus_rec(min) tBit tBittBit

15ATA6663/ATA6664 [DATASHEET] 9146I–AUTO–10/14 Figure 6-2. Application Circuit VS VS INH EN RXD 12V VBATTERY 5kΩ 100nF ATA6663/ATA6664 2.7kΩ 10kΩ Short-circuit and overtemperature protection Control unit Slew rate control Wake-up bus timer Filter Master node pull-up Wake-up timer TXD Time-out timer Sleep mode Receiver WAKE TXD Microcontroller IO VDD External switch GND VS LIN LIN sub bus 220pF 22μF GND

ATA6663/ATA6664 [DATASHEET] 9146I–AUTO–10/14 8. Package Information Figure 8-1. SO8 7. Ordering Information Extended Type Number Package Remarks ATA6663-FAQW-1 DFN8 LIN transceiver, Pb-free, 6k, taped and reeled ATA6663-GAQW SO8 LIN transceiver, Pb-free, 4k, taped and reeled ATA6664-GAQW SO8 LIN transceiver, Pb-free, 4k, taped and reeled Package Drawing Contact: packagedrawings@atmel.com GPC DRAWING NO. REV. TITLE 6.543-5185.01-4 1 05/08/14 COMMON DIMENSIONS (Unit of Measure = mm) MIN NOM NOTE MAXSymbol Dimensions in mm specifications according to DIN technical drawings 0.15 0.250.1A1 3.9 43.8E1 0.4 0.50.3b

1.27 BSCe

0.2 0.250.15C 0.65 0.90.4L 66 . 25.8E 4.9 54.8D 1.47 1.551.4A2 1.65 1.81.5A D b e A C E L Pin 1 identity

17ATA6663/ATA6664 [DATASHEET] 9146I–AUTO–10/14 Figure 8-2. DFN8 Package Drawing Contact: packagedrawings@atmel.com GPC DRAWING NO. REV. TITLE 6.543-5165.03-4 1 10/11/13 Package: VDFN_3x3_8L Exposed pad 2.4x1.6 COMMON DIMENSIONS (Unit of Measure = mm) MIN NOM NOTE MAXSymbol Dimensions in mm specifications according to DIN technical drawings 0.035 0.050A1 33 . 12.9E 0.3 0.350.25b 0.65e 0.4 0.450.35L 1.6 1.71.5E2 2.4 2.52.3D2 33 . 12.9D 0.21 0.260.16A3 0.85 0.90.8A D PIN 1 ID Partially Plated Surface E A b L Z 10:1 Top View Side View Bottom View e Z

ATA6663/ATA6664 [DATASHEET] 9146I–AUTO–10/14 9. Revision History Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this document. Revision No. History 9146I-AUTO-10/14

• Put datasheet in the latest template
• Section 7 “Ordering Information” on page 16 updated
• Section 8 “Package Information” on pages 16 to 17 updated 9146H-AUTO-03/14 • Section 7 “Ordering Information” on page 16: Order quantity of ATA6663-FAQW updated 9146G-AUTO-06/12 • Section 5“Electrical Characteristics” numbers 3.2 and 4.2 on page 10 to 11 updated 9146F-AUTO-10/11 • Section 6 “Thermal Characteristics DFN8” on page 10 implemented 9146E-AUTO-03/11
• Figure 1-1 “Block Diagram” on page 2 updated
• Section 3.15 “Fail-safe Features” on page 9 updated 9146D-AUTO-09/10
• Section 7 “Ordering Information” on page 17 updated
• Section 8 “Package Information” on pages 17 to 18 updated 9146C-AUTO-07/10 • Section 6 “Electrical Characteristics” numbers 9.4 and 9.5 on page 13 updated 9146B-AUTO-05/10
• Features updated
• Headings 3.6 and 3.10: text updated
• Abs.Max.Ratings table: row “ESD HBM according to STM5.1” updated

Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 | www.atmel.com © 2014 Atmel Corporation. / Rev.: 9146I–AUTO–10/14 Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. DISCLAIMER: The information in this document is provided in c onnection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDIT IONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WH ATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS P RODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PU NITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMI TATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION ) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no r epresentations or warranties with respect to the accuracy or c ompleteness of the contents of this document and reserves the right to make changes to specificatio ns and products descriptions at any time without notice. Atmel d oes not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atme l products are not suitable for, and shall not be used in, automo tive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIM ER: Atmel products are not designed for and will not be used in connection with any applications where the failure of such products would reasonably be expected to re sult in significant personal inju ry or death (“Safety-Critical A pplications”) without an Atmel officer's specific written consent. Safety-Critical Applications incl ude, without limitation, life support devices and systems, equipment or systems for t he operation of nuclear facilities and weapons systems. Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are not designed nor intended for use in automot ive applications unless spec ifically designated by Atmel as automotive-grade.