DATASHEET SEARCH SITE

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 22

Technical content

Features

 Serial Peripheral Interface (SPI) Compatible  Supports SPI Modes 0 (0,0) and 3 (1,1) ̶ Data Sheet Describes Mode 0 Operation  Low-voltage and Standard-voltage Operation ̶ VCC = 1.8V to 5.5V  20MHz Clock Rate (5V)  8-byte Page Mode  Block Write Protection ̶ Protect 1/4, 1/2, or Entire Array  Write Protect (WP) Pin and Write Disable Instructions for Both Hardware and Software Data Protection  Self-timed Write Cycle (5 ms max)  High Reliability ̶ Endurance: 1,000,000 Write Cycles ̶ Data Retention: 100 Years  Green (Pb/Halogen-free/RoHS Compliant) Packaging Options  Die Sales: Wafer Form, Waffle Pack, and Bumped Wafers

Description

The Atmel® AT25010B/020B/040B provides 1024/2048/4096 bits of Serial Electrically Erasable Programmable Read-Only Memory (EEPROM) organized as 128/256/512 words of 8 bits each. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. The AT25010B/020B/040B is available in space saving, JEDEC SOIC, UDFN, TSSOP, XDFN, and VFBGA packages. The AT25010B/020B/040B is enabled through the Chip Select pin ( CS) and accessed via a 3-Wire interface consisting of Serial Data Input (SI), Serial Data Output (SO), and Serial Clock (SCK). All programming cycles are completely self-timed, and no separate erase cycle is required before write. Block Write protection is enabled by programming the status register with one of four blocks of Write Protection. Separate Program Enable and Program Disable instructions are provided for additional data protection. Hardware Data Protection is provided via the WP pin to protect against inadvertent write attempts. The HOLD pin may be used to suspend any serial communication without resetting the serial sequence. AT25010B, AT25020B, AT25040B SPI Serial EEPROM 1K (128x8), 2K (256x8), 4K (512x8) DATASHEET

AT25010B/020B/040B [DATASHEET] Atmel-8707E-SEEPROM-AT25010B-020B-040B-Datasheet_052014 1. Pin Configurations Table 1-1. Pin Configurations 2. Absolute Maximum Ratings* Pin Name Function CS Chip Select SCK Serial Data Clock SI Serial Data Input SO Serial Data Output GND Ground VCC Power Supply WP Write Protect HOLD Suspends Serial Input Voltage on any pin *Notice: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Note: Drawings are not to scale. 8-lead SOIC CS SO WP GND VCC HOLD SCK SI Top View Top View 8-lead TSSOP CS SO WP GND V CC HOLD SCK SI VCC HOLD SCK SI CS SO WP GND 8-ball VFBGA Bottom View 8-pad UDFN/XDFN Bottom View VCC HOLD SCK SI CS SO WP GND

3AT25010B/020B/040B [DATASHEET] Atmel-8707E-SEEPROM-AT25010B-020B-040B-Datasheet_052014 3. Block Diagram Figure 3-1. Block Diagram Memory Array 128/256/512 x 8 Status Register Data Register Mode Decode Logic Clock Generator Output Buffer Address Decoder VCC

AT25010B/020B/040B [DATASHEET] Atmel-8707E-SEEPROM-AT25010B-020B-040B-Datasheet_052014 4. Electrical Characteristics

4.1 Pin Capacitance (1)

Table 4-1. Pin Capacitance Note: 1. This parameter is characterized and is not 100% tested.

4.2 DC Characteristics

Table 4-2. DC Characteristics Note: 1. V IL min and VIH max are reference only and are not tested. Applicable over recommended operating range from TA = 25°C, f = 1MHz, VCC = +5V (unless otherwise noted). Symbol Test Conditions Max Units Conditions COUT Output Capacitance (SO) 8 pF VOUT = 0V CIN Input Capacitance (CS, SCK, SI, WP, HOLD) 6 pF VIN = 0V Applicable over recommended operating range from: TAI = 40C to +85C, VCC = +1.8V to +5.5V, (unless otherwise noted). Symbol Parameter Test Condition Min Typ Max Units VCC1 Supply Voltage 1.8 5.5 V VCC2 Supply Voltage 2.5 5.5 V VCC3 Supply Voltage 4.5 5.5 V ICC1 Supply Current VCC = 5V at 20MHz SO = Open, Read 8.5 10 mA ICC2 Supply Current VCC = 5V at 10MHz SO = Open, Read, Write 4.5 5 mA ICC3 Supply Current VCC = 5V at 1MHz SO = Open, Read, Write 2 3 mA ISB1 Standby Current VCC = 1.8V, CS = VCC 0.1 0.5 μA ISB2 Standby Current VCC = 2.5V, CS = VCC 0.2 1 μA ISB3 Standby Current VCC = 5V, CS = VCC 2 3.5 μA IIL Input Leakage VIN = 0V to VCC 3 μA IOL Output Leakage VIN = 0V to VCC TAC = 0°C to 70°C 3 3 μA VIL (1) Input Low-voltage 0.6 VCC x 0.3 V VIH (1) Input High-voltage VCC x 0.7 VCC + 0.5 V VOL1 Output Low-voltage 3.6V  VCC  5.5V IOL = 3mA 0.4 V VOH1 Output High-voltage 3.6V  VCC  5.5V IOH = 1.60mA VCC  0.8 V VOL2 Output Low-voltage 1.8V  VCC  3.6V IOL = 0.15mA 0.2 V VOH2 Output High-voltage 1.8V  VCC  3.6V IOH = 100μA VCC 0.2 V

5AT25010B/020B/040B [DATASHEET] Atmel-8707E-SEEPROM-AT25010B-020B-040B-Datasheet_052014

4.3 AC Characteristics

Table 4-3. AC Characteristics Applicable over recommended operating range from TAI = 40 to +85°C, VCC = As Specified, CL = 1 TTL Gate and 30pF (unless otherwise noted). Symbol Parameter Voltage Min Max Units fSCK SCK Clock Frequency 4.5  5.5 2.5  5.5 1.8 5.5 MHz tRI Input Rise Time 4.5  5.5 2.5  5.5 1.8 5.5 μs tFI Input Fall Time 4.5  5.5 2.5  5.5 1.8 5.5 μs tWH SCK High Time 4.5 5.5 2.5  5.5 1.8 5.5 ns tWL SCK Low Time 4.5  5.5 2.5 5.5 1.8 5.5 ns tCS CS High Time 4.5  5.5 2.5  5.5 1.8  5.5 100 100 200 ns tCSS CS Setup Time 4.5  5.5 2.5 5.5 1.8 5.5 100 100 200 ns tCSH CS Hold Time 4.5  5.5 2.5 5.5 1.8  5.5 100 100 200 ns tSU Data In Setup Time 4.5 5.5 2.5 5.5 1.85.5 ns tH Data In Hold Time 4.5  5.5 2.5 - 5.5 1.8 - 5.5 ns tHD Hold Setup Time 4.5  5.5 2.5  5.5 1.8 5.5 ns tCD Hold Hold Time 4.5  5.5 2.5  5.5 1.8  5.5 ns tV Output Valid 4.5 5.5 2.5 5.5 1.8  5.5 ns tHO Output Hold Time 4.5 5.5 2.5 5.5 1.8 5.5 ns

AT25010B/020B/040B [DATASHEET] Atmel-8707E-SEEPROM-AT25010B-020B-040B-Datasheet_052014 Note: 1. This parameter is characterized and is not 100% tested. 5. Serial Interface Description Master: The device that generates the serial clock. Slave: Because the Serial Clock pin (SCK) is always an input, the AT25010B/020B/040B always operates as a slave. Transmitter/Receiver: The AT25010B/020B/040B has separate pins designated for data transmission (SO) and reception (SI). MSB: The Most Significant Bit (MSB) is the first bit transmitted and received. Serial Opcode: After the device is selected with CS going low, the first byte will be received. This byte contains the opcode which defines the operations to be performed. The opcode also contains address bit A8 in both the read and write instructions for the AT25040B. Invalid Opcode: If an invalid opcode is received, no data will be shifted into the AT25010B/020B/040B, and the serial output pin (SO) will remain in a high-impedance state until the falling edge of CS is detected again. This will reinitialize the serial communication. Chip Select: The AT25010B/020B/040B is selected when the CS pin is low. When the device is not selected, data will not be accepted via the SI pin, and the SO pin will remain in a high impedance state. Hold: The HOLD pin is used in conjunction with the CS pin to select the AT25010B/020B/040B. When the device is selected and a serial sequence is underway, HOLD can be used to pause the serial communication with the master device without resetting the serial sequence. To pause, the HOLD pin must be brought low while the SCK pin is low. To resume serial communication, the HOLD pin is brought high while the SCK pin is low (SCK may still toggle during HOLD). Inputs to the SI pin will be ignored while the SO pin is in the high impedance state. Write Protect: The write protect pin (WP) will allow normal read/write operations when held high. When the WP pin is brought low, all write operations are inhibited. WP going low while CS is still low will interrupt a write to the AT25010B/020B/040B. If the internal write cycle has already been initiated, WP going low will have no effect on any write operation. tLZ Hold to Output Low Z 4.5  5.5 2.5  5.5 1.8  5.5 100 ns tHZ Hold to Output High Z 4.5  5.5 2.5  5.5 1.8 5.5 100 ns tDIS Output Disable Time 4.5 5.5 2.5  5.5 1.8 5.5 100 ns tWC Write Cycle Time 4.5  5.5 2.5  5.5 1.8 5.5 ms Endurance(1) 5V, 25C, Page Mode 1M Write Cycles Table 4-3. AC Characteristics (Continued) Applicable over recommended operating range from TAI = 40 to +85°C, VCC = As Specified, CL = 1 TTL Gate and 30pF (unless otherwise noted). Symbol Parameter Voltage Min Max Units

7AT25010B/020B/040B [DATASHEET] Atmel-8707E-SEEPROM-AT25010B-020B-040B-Datasheet_052014 Figure 5-1. SPI Serial Interface Master: Microcontroller Slave: AT25010B/020B/040B Data Out (MOSI) Data In (MISO) Serial Clock (SPI CK) SS0 SS1 SS2 SS3 SI SO SCK CS SI SO SCK CS SI SO SCK CS SI SO SCK CS

AT25010B/020B/040B [DATASHEET] Atmel-8707E-SEEPROM-AT25010B-020B-040B-Datasheet_052014 6. Functional Description The AT25010B/020B/040B is designed to interface directly with the synchronous Serial Peripheral Interface (SPI) of the 6805 and 68HC11 series of microcontrollers. The AT25010B/020B/040B utilizes an 8-bit instruction register. The list of instructions and their operation codes are contained in Figure 6-1. All instructions, addresses, and data are transferred with the MSB first and start with a high-to-low CS transition. Table 6-1. Instruction Set for the AT25010B/020B/040B Note: 1. “A” represents MSB address bit A8 for the AT25040B. Write Enable (WREN): The device will power-up in the Write Disable state when VCC is applied. All programming instructions must therefore be preceded by a Write Enable instruction. The WP pin must be held high during a WREN instruction. Write Disable (WRDI): To protect the device against inadvertent writes, the Write Disable instruction disables all programming modes. The WRDI instruction is independent of the status of the WP pin. Read Status Register (RDSR): The Read Status Register instruction provides access to the status register. The Read/Busy and Write Enable status of the device can be determined by the RDSR instruction. Similarly, the Block Write Protection bits indicate the extent of protection employed. These bits are set by using the WRSR instruction. Table 6-2. Status Register Format Table 6-3. Read Status Register Bit Definition Instruction Name Instruction Format Operation WREN 0000 X110 Set Write Enable Latch WRDI 0000 X100 Reset Write Enable Latch RDSR 0000 X101 Read Status Register WRSR 0000 X001 Write Status Register READ 0000 A011 Read Data from Memory Array WRITE 0000 A010 Write Data to Memory Array Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 X X X X BP1 BP0 WEN RDY Bit Definition Bit 0 (RDY) Bit 0 = 0 (RDY) indicates the device is ready. Bit 0 = 1 indicates the write cycle is in progress. Bit 1 (WEN) Bit 1 = 0 indicates the device is not write enabled. Bit 1 = 1 indicates the device is write enabled. Bit 2 (BP0) See Table 6-4. Bit 3 (BP1) See Table 6-4. Bits 4 – 7 are zeros when device is not in an internal write cycle. Bits 0 – 7 are ones during an internal write cycle.

9AT25010B/020B/040B [DATASHEET] Atmel-8707E-SEEPROM-AT25010B-020B-040B-Datasheet_052014 Write Status Register (WRSR): The WRSR instruction allows the user to select one of four levels of protection. The AT25010B/020B/040B is divided into four array segments. None, one-quarter (¼), one-half (½), or all of the memory segments can be protected. Any of the data within any selected segment will therefore be read-only. The block write protection levels and corresponding status register control bits are shown in Table 6-4. Bits BP1 and BP0 are nonvolatile cells that have the same properties and functions as the regular memory cells (e.g., WREN, t WC, RDSR). Table 6-4. Block Write Protect Bits Read Sequence (READ): Reading the AT25010B/020B/040B via the SO pin requires the following sequence. After the CS line is pulled low to select a device, the Read opcode (including A8 for the AT25040B) is transmitted via the SI line followed by the byte address to be read (A7 A0). Upon completion, any data on the SI line will be ignored. The data (D7 D0) at the specified address is then shifted out onto the SO line. If only one byte is to be read, the CS line should be driven high after the data comes out. The Read Sequence can be continued since the byte address is automatically incremented and data will continue to be shifted out. When the highest address is reached, the address counter will roll-over to the lowest address allowing the entire memory to be read in one continuous read cycle. Write Sequence (WRITE): In order to program the AT25010B/020B/040B, the Write Protect pin ( WP) must be held high and two separate instructions must be executed. First, the device must be write enabled via the WREN instruction. Then a Write (WRITE) instruction may be executed. Also, the address of the memory location(s) to be programmed must be outside the protected address field location selected by the Block Write Protection level. During an internal write cycle, all commands will be ignored except the RDSR instruction. A Write instruction requires the following sequence. After the CS line is pulled low to select the device, the Write opcode (including A8 for the AT25040B) is transmitted via the SI line followed by the byte address (A7 A0) and the data (D7 D0) to be programmed. Programming will start after the CS pin is brought high. The low-to-high transition of the CS pin must occur during the SCK low time immediately after clocking in the D0 (LSB) data bit. The Ready/Busy status of the device can be determined by initiating a Read Status Register (RDSR) instruction. If Bit 0 = 1, the write cycle is still in progress. If Bit 0 = 0, the write cycle has ended. Only the RDSR instruction is enabled during the write programming cycle. The AT25010B/020B/040B is capable of an 8-byte Page Write operation. After each byte of data is received, the three low-order address bits are internally incremented by one; the six high-order bits of the address will remain constant. If more than eight bytes of data are transmitted, the address counter will roll-over and the previously written data will be overwritten. The AT25010B/020B/040B is automatically returned to the Write Disable state at the completion of a write cycle. Note: If the WP pin is brought low or if the device is not Write Enabled (WREN), the device will ignore the Write instruction and will return to the standby state, when CS is brought high. A new CS falling edge is required to reinitiate the serial communication. Level Status Register Bits Array Addresses Protected BP1 BP0 AT25010B AT25020B AT25040B 0 0 0 None None None 2 ( ½) 1 0 40 7F 80 FF 100 1FF 3 (All) 1 1 00 7F 00 FF 000 1FF

13AT25010B/020B/040B [DATASHEET] Atmel-8707E-SEEPROM-AT25010B-020B-040B-Datasheet_052014 8. Ordering Code Detail AT25010B-SSHL-B Atmel Designator Product Family Device Density Device Revision Shipping Carrier Option Package Device Grade or Wafer/Die Thickness Package Option 010 = 1k 020 = 2k 040 = 4k B or blank = Bulk (Tubes) T = Tape and Reel Operating Voltage M = 1.8V to 5.5V H = Green, NiPdAu Lead Finish, Industrial Temperature Range (-40˚C to +85˚C) U = Green, Matte Sn Lead Finish, Industrial Temperature Range (-40˚C to +85˚C) 11 = 11mil Wafer Thickness SS = JEDEC SOIC X = TSSOP MA = UDFN ME = XDFN C = VFBGA WWU = Wafer unsawn WDT = Die in Tape and Reel

AT25010B/020B/040B [DATASHEET] Atmel-8707E-SEEPROM-AT25010B-020B-040B-Datasheet_052014 9. Part Markings DRAWING NO. REV. TITLE 25010-02-04BSM B 1/15/14 25010-02-04BSM, AT25010B, AT25020B and AT25040B Package Marking Information Package Mark Contact: DL-CSO-Assy_eng@atmel.com AAAAAAAA###% @ATMLHYWW 8-lead SOIC 8-lead TSSOP AAAAAAA ###% @ ATHYWW 8-pad UDFN ### H%@ YXX 2.0 x 3.0 mm Body Note 2: Package drawings are not to scale Note 1: designates pin 1 AT25010B, AT25020B and AT25040B: Package Marking Information Catalog Number Truncation AT25010B Truncation Code ###: 51B AT25020B Truncation Code ###: 52B AT25040B Truncation Code ###: 54B Date Codes Voltages Y = Year M = Month WW = Work Week of Assembly % = Minimum Voltage 4: 2014 8: 2018 A: January 02: Week 2 L: 1.8V min 5: 2015 9: 2019 B: February 04: Week 4 7: 2017 1: 2021 L: December 52: Week 52 Country of Assembly Lot Number Grade/Lead Finish Material @ = Country of Assembly AAA...A = Atmel Wafer Lot Number H: Industrial/NiPdAu U: Industrial/Matte Tin/SnAgCu Trace Code Atmel Truncation XX = Trace Code (Atmel Lot Numbers Correspond to Code) AT: Atmel Example: AA, AB.... YZ, ZZ ATM: Atmel ATML: Atmel 1.5 x 2.0 mm Body 8-ball VFBGA PIN 1 ###U YMXX ### YXX 8-pad XDFN 1.8 x 2.2 mm Body

15AT25010B/020B/040B [DATASHEET] Atmel-8707E-SEEPROM-AT25010B-020B-040B-Datasheet_052014 10. Ordering Information Notes: 1. B = Bulk delivery in tubes.  SOIC and TSSOP = 100 per tube 2. T = Tape and Reel  SOIC = 4,000 per reel  TSSOP, UDFN, XDFN, and VFBGA = 5,000 per reel 3. Contact Atmel Sales for Wafer sales. Ordering Code Lead Finish Package Voltage Operation Range AT25010B-SSHL-B (1) NiPdAu (Lead-free/Halogen-free) 8S1 1.8V to 5.5V Industrial Temperature (40 to 85C) AT25010B-SSHL-T (2) AT25010B-XHL-B (1) AT25010B-XHL-T (2) AT25010B-MAHL-T (2) 8MA2 AT25010B-MEHL-T (2) 8ME1 AT25010B-CUL-T (2) SnAgCu (Lead-free/Halogen-free) 8U3-1 AT25010B-WWU11L (3) — Wafer AT25020B-SSHL-B (1) NiPdAu (Lead-free/Halogen-free) 8S1 1.8V to 5.5V Industrial Temperature (40 to 85C) AT25020B-SSHL-T (2) AT25020B-XHL-B (1) AT25020B-XHL-T (2) AT25020B-MAHL-T (2) 8MA2 AT25020B-MEHL-T (2) 8ME1 AT25020B-CUL-T (2) SnAgCu (Lead-free/Halogen-free) 8U3-1 AT25020B-WWU11L (3) — Wafer AT25040B-SSHL-B (1) NiPdAu (Lead-free/Halogen-free) 8S1 1.8V to 5.5V Industrial Temperature (40 to 85C) AT25040B-SSHL-T (2) AT25040B-XHL-B (1) AT25040B-XHL-T (2) AT25040B-MAHL-T (2) 8MA2 AT25040B-MEHL-T (2) 8ME1 AT25040B-CUL-T (2) SnAgCu (Lead-free/Halogen-free) 8U3-1 AT25040B-WWU11L (3) — Wafer Package Type 8S1 8-lead, 0.15" wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8X 8-lead, 4.40mm body, Plastic Thin Shrink Small Outline Package (TSSOP) 8MA2 8-pad, 2.00mm x 3.00mm body, 0.50mm pitch, Plastic Ultra Thin Dual Flat No Lead (UDFN) 8ME1 8-pad, 1.80mm x 2.20mm body, 0.40mm pitch, Extra Thin Dual Flat No Lead (XDFN) 8U3-1 8-ball, 1.50mm x 2.00mm body, 0.50mm pitch, Die Ball Grid Array (VFBGA)

AT25010B/020B/040B [DATASHEET] Atmel-8707E-SEEPROM-AT25010B-020B-040B-Datasheet_052014 11. Packaging Information 11.1 8S1 — 8-lead JEDEC SOIC DRAWING NO. REV. TITLE GPC COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 A 1.35 – 1.75 b 0.31 – 0.51 C 0.17 – 0.25 D 4.80 – 5.05 E1 3.81 – 3.99 E 5.79 – 6.20 e 1.27 BSC L 0.40 – 1.27 ØØ 0° – 8° Ø E N TOP VIEW C END VIEW A b L e D SIDE VIEW Package Drawing Contact: packagedrawings@atmel.com 8S1 G 6/22/11 Notes: This drawing is for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 8S1, 8-lead (0.150” Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) SWB

17AT25010B/020B/040B [DATASHEET] Atmel-8707E-SEEPROM-AT25010B-020B-040B-Datasheet_052014 11.2 8X — 8-lead TSSOP DRAWING NO. REV. TITLE GPC COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A - - 1.20 A1 0.05 - 0.15 A2 0.80 1.00 1.05 D 2.90 3.00 3.10 2, 5 E 6.40 BSC E1 4.30 4.40 4.50 3, 5 b 0.19 0.25 0.30 4 e 0.65 BSC L 0.45 0.60 0.75 L1 1.00 REF C 0.09 - 0.20 Side View End ViewTop View A L D N b Pin 1 indicator this corner E e Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15mm (0.006in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25mm (0.010in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07mm. 5. Dimension D and E1 to be determined at Datum Plane H. Package Drawing Contact: packagedrawings@atmel.com 8X E 2/27/14 8X, 8-lead 4.4mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) TNR C

AT25010B/020B/040B [DATASHEET] Atmel-8707E-SEEPROM-AT25010B-020B-040B-Datasheet_052014 11.3 8MA2 — 8-pad UDFN DRAWING NO. REV. TITLE GPC 8MA2 E 12/20/13 8MA2, 8-pad 2 x 3 x 0.6mm Body, Thermally Enhanced Plastic Ultra Thin Dual Flat No-Lead Package (UDFN) YNZ COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A 0.50 0.55 0.60 A1 0.0 0.02 0.05 A2 - - 0.55 D 1.90 2.00 2.10 D1 1.20 - 1.60 E 2.90 3.00 3.10 E1 1.20 - 1.60 b 0.18 0.25 0.30 3 C 1.52 REF L 0.30 0.35 0.40 e 0.50 BSC K 0.20 - - TOP VIEW SIDE VIEW BOTTOM VIEW Package Drawing Contact: packagedrawings@atmel.com C E Pin 1 ID D A e (6x) L (8x) b (8x) Pin#1 ID K Notes: 1. This drawing is for general information only. Refer to Drawing MO-229, for proper dimensions, tolerances, datums, etc. 2. The Pin #1 ID is a laser-marked feature on Top View. 3. Dimensions b applies to metallized terminal and is measured between 0.15 mm and 0.30 mm from the terminal tip. If the terminal has the optional radius on the other end of the terminal, the dimension should not be measured in that radius area. 4. The Pin #1 ID on the Bottom View is an orientation feature on the thermal pad.

19AT25010B/020B/040B [DATASHEET] Atmel-8707E-SEEPROM-AT25010B-020B-040B-Datasheet_052014 11.4 8ME1 — 8-pad XDFN Package Drawing Contact: packagedrawings@atmel.com GPC DRAWING NO. REV. TITLE COMMON DIMENSIONS (Unit of Measure = mm) DTP SYMBOL MIN NOM MAX NOTE 0.00 1.70 2.10 0.15 0.26 A D E b e L 1.80 2.20 0.20

0.40 TYP

1.20 REF

0.30 0.40 0.05 1.90 2.30 0.25 0.35 End View 8ME1 B 9/10/2012 8ME1, 8-pad (1.80mm x 2.20mm body) Extra Thin DFN (XDFN) Top View 6 57 E D 1 2 PIN #1 ID 0.10 0.15 b L b e PIN #1 ID A Side View

AT25010B/020B/040B [DATASHEET] Atmel-8707E-SEEPROM-AT25010B-020B-040B-Datasheet_052014 11.5 8U3-1 — 8-ball VFBGA DRAWING NO. REV. TITLE GPC Package Drawing Contact: packagedrawings@atmel.com 8U3-1 F 6/11/13 8U3-1, 8-ball, 1.50mm x 2.00mm body, 0.50mm pitch, Very Thin, Fine-Pitch Ball Grid Array Package (VFBGA) GXU COMMON DIMENSIONS (Unit of Measure - mm) SYMBOL MIN NOM MAX NOTE A 0.73 0.79 0.85 A1 0.09 0.14 0.19 A2 0.40 0.45 0.50 b 0.20 0.25 0.30 2 D 1.50 BSC E 2.0 BSC e 0.50 BSC e1 0.25 REF d 1.00 BSC d1 0.25 REF 1. This drawing is for general information only. 2. Dimension ‘b’ is measured at maximum solder ball diameter. Notes: SIDE VIEW A PIN 1 BALL PAD CORNER TOP VIEW E D b

8 SOLDER BALLS

(d1) d 432 (e1) e PIN 1 BALL PAD CORNER

21AT25010B/020B/040B [DATASHEET] Atmel-8707E-SEEPROM-AT25010B-020B-040B-Datasheet_052014 12. Revision History Doc. Rev. Date Comments 8707E 05/2014 Update part markings, package drawings, package 8A2 to 8X, template, logos, and disclaimer page. No change to functional specification. 8707D 04/2013 Correct WRSR waveform figure 4-5, bit 7 is not writable. Update Atmel logos and disclaimer page. 8707C 06/2011 Correct AT25040B-SSHL marking detail. Replace 8A2 package drawing with version E. 8707B 10/2010 Remove Preliminary. 8707B 03/2010 Replace 8Y6 with 8MA2. 8707A 02/2010 Initial document release.

Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 | www.atmel.com © 2014 Atmel Corporation. / Rev.: Atmel-8707E-SEEPROM-AT25010B-020B-040B-Datasheet_052014. Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities, and others are registered trademarks or trademarks of Atmel Corporation in U.S. and other countries. Other terms and product names may be trademarks of others. DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDIT IONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS P RODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMI TATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or c ompleteness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel d oes not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automo tive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical A pplications”) without an Atmel officer's specific written consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for t he operation of nuclear facilities and weapons systems. Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.