DATASHEET SEARCH SITE

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 29

Technical content

Atmel-8807D-SEEPROM-AT24MAC402-602-Datasheet_082013 Standard Serial EEPROM Features  Low-voltage Operation ̶ 1.7V Minimum (VCC = 1.7V to 5.5V)  Internally Organized as 256 x 8 (2K)  I2C-compatible (2-wire) Serial Interface  Schmitt Trigger, Filtered Inputs for Noise Suppression  Bi-directional Data Transfer Protocol  400kHz (1.7V) and 1MHz (2.5V, 5.0V) Compatibility  Write Protect Pin for Hardware Data Protection of the Entire Array  Permanent and Reversible Software Write Protection for the First-half of the Array ̶ Software Procedure to Verify Write Protect Status  16-byte Page Write Modes ̶ Partial Page Writes Allowed  Self-timed Write Cycle (5ms max)  High-reliability ̶ Endurance: 1,000,000 Write Cycles ̶ Data Retention: 100 Years  Green Package Options (PB/Halide-free/RoHS Compliant) ̶ 8-lead JEDEC SOIC, 8-lead TSSOP, 8-pad UDFN, and 5-lead SOT23  Die Sale Options: Wafer Form and Tape and Reel Enhanced Features in the MAC Serial EEPROM Family  Factory-programmed EUI-48 or EUI-64 Compatible Address ̶ Permanently Locked, Read-only Value ̶ Stored in a Separate Memory Area ̶ Guaranteed Unique EUI Address  Custom Programming Services Available ̶ Manage and Program Customer’s IEEE Assigned OUI  Unique Factory-programmed 128-bit Serial Number ̶ Unique for all Atmel® AT24CS, AT93CS, and AT25S Series Serial EEPROMs ̶ Permanently Locked, Read-only Value ̶ Stored in a Separate Memory Area AT24MAC402 and AT24MAC602 I2C-Compatible (2-wire) 2-Kbit Serial EEPROM with a Factory-Programmed EUI-48™ or EUI-64™ Address Plus an Embedded Unique 128-bit Serial Number 2-Kbit (256 x 8) DATASHEET

AT24MAC402/602 [DATASHEET] Atmel-8807D-SEEPROM-AT24MAC402-602-Datasheet_082013

Description

The Atmel AT24MAC402 and AT24MAC602 provides 2048 bits of Serial Electrically-Erasable Programmable Read-Only Memory (EEPROM) organized as 256 words of eight bits each and is accessed via an I 2C-compatible (2-wire) serial interface. In addition, AT24MAC402/602 incorporates an easy and inexpensive method to obtain a globally unique MAC or EUI address (EUI-48 or EUI-64). AT24MAC402 is an EUI-48 compatible device that contains a 48-bit EUI address, and AT24MAC602 is an EUI-64 compatible device that contains a 64-bit EUI address. The EUI-48 and EUI-64 addresses can be assigned as the actual physical address of a system hardware device or node or it can be assigned to a software instance. These addresses are factory programmed by Atmel and permanently write protected in an extended memory block located outside of the standard 2-Kbit bit memory array. In addition, the AT24MAC402/602 provides the value added feature of a factory-programmed, guaranteed unique 128-bit serial number located in the extended memory block (same area as the EUI address values). The serial number is Atmel factory-programmed and permanently write protected. This 128-bit serial number is compatible with all AT24CS, AT93CS, and AT25S family serial numbers, therefore, providing guaranteed unique serial numbers for any application that is also using Atmel Serial EEPROMs. The first-half of the AT24MAC402/602 incorporates a permanent and a reversible software write protection feature while a hardware write protect feature for the entire array is available via an external pin. The permanent software write protection is enabled by sending a special command to the device. This protection cannot be reversed once executed. However, the reversible software write protection can be reversed by sending and executing a special command. The hardware write protection is controlled by the WP pin state and can be used to protect the entire array regardless of whether or not the software write protection has been enabled. The software and hardware write protection features allow the user the flexibility to protect no portion of the memory, the first-half of the memory, or the entire memory array depending on the specific needs of the application. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operations are essential. The AT24MAC402/602 is available in space saving 8-lead JEDEC SOIC, 8-lead TSSOP, 8-pad UDFN, and 5-lead SOT23 packages. Both devices operate across a wide supply voltage range from 1.7V to 5.5V V CC. Figure 1. Pin Configurations is not possible due to these pins not being available. See “Write Protection” on page 13 for more details.

  1. Drawings are not to scale.

3AT24MAC402/602 [DATASHEET] Atmel-8807D-SEEPROM-AT24MAC402-602-Datasheet_082013 1. Absolute Maximum Ratings* 2. Block Diagram Figure 2-1. Block Diagram Voltage on any pin *Notice: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Start Stop Logic Data Word ADDR/Counter Row Decoder Device Address Comparator Data Latches DOUT / ACK Logic Column Decoder EEPROM Array Serial Control Logic High Voltage Pump & Timing 128-bit Serial Number Serial MUX Read Read/Write Enable COMP Load INC VCC GND WP SCL SDA DOUT DIN MAC-48 EUI-48 EUI-64 AddressRead

AT24MAC402/602 [DATASHEET] Atmel-8807D-SEEPROM-AT24MAC402-602-Datasheet_082013 3. Pin Description Serial Clock (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative edge clock data out of each device. Serial Data (SDA): The SDA pin is bidirectional for serial data transfer. This pin is open-drain driven and may be wire-ORed with any number of other open-drain or open collector devices. Device Addresses (A0, A1, A2): The A0, A1, and A2 pins are device address inputs that are hard wired for the AT24MAC402/602. As many as eight 2K devices may be addressed on a single bus system. Device addressing is discussed in detail in Section 6., “Device Addressing” on page 11. Write Protect (WP): The AT24MAC402/602 has a Write Protect pin that provides hardware data protection. When the Write Protect pin is connected to ground (GND), normal Read/Write operations to the full array are possible. When the Write Protect pin is connected to V CC, all write operations to the memory are inhibited, but read operations are still possible. However, due to capacitive coupling that may appear during customer applications, Atmel recommends always connecting the WP pins to a known state. When using a pull-up resistor, Atmel recommends using 10k or less. The write protection operation is summarized in Table 3-1 below.

3.1 Write Protection Modes

Table 3-1. Write Protection Modes

3.2 Pin Capacitance

Table 3-2. Pin Capacitance (1) Note: 1. This parameter is characterized and is not 100% tested. WP Pin Status Permanent Write Protect Register Reversible Write Protect Register Part of the Array Write Protected VCC — — Full Array (2K) GND or Floating Not Programmed Not Programmed Normal Read/Write GND or Floating Programmed — First-half of Array GND or Floating — Programmed First-half of Array Symbol Test Condition Max Units Conditions CI/O Input/Output Capacitance (SDA) 8 pF VI/O = 0V CIN Input Capacitance (A0, A1, A2, SCL) 6 pF VIN = 0V

5AT24MAC402/602 [DATASHEET] Atmel-8807D-SEEPROM-AT24MAC402-602-Datasheet_082013

3.3 DC Characteristics

Table 3-3. DC Characteristics Note: 1. V IL min and VIH max are reference only and are not tested.

3.4 AC Characteristics

Table 3-4. AC Characteristics Note: 1. This parameter is characterized and is not 100% tested. Applicable over recommended operating range from: TAI = -40°C to +85°C, VCC = 1.7V to 5.5V (unless otherwise noted). Symbol Parameter Test Condition Min Typ Max Units VCC Supply Voltage 1.7 5.5 V ICC1 Supply Current VCC = 5.0V Read at 400kHz 0.4 1.0 mA ICC2 Supply Current VCC = 5.0V Write at 400kHz 2.0 3.0 mA ISB1 Standby Current VCC = 1.7V VIN = VCC or VSS 1.0 μA ISB2 Standby Current VCC = 2.5V VIN = VCC or VSS 2.0 μA ISB3 Standby Current VCC = 5.5V VIN = VCC or VSS, A0 = VSS 6.0 μA ILI Input Leakage Current VIN = VCC or VSS 0.10 3.0 μA ILO Output Leakage Current VOUT = VCC or VSS 0.05 3.0 μA VIL Input Low Level(1) –0.6 VCC x 0.3 V VIH Input High Level(1) VCC x 0.7 VCC + 0.5 V VOL1 Output Low Level VCC = 1.7V IOL = 0.15mA 0.2 V VOL2 Output Low Level VCC = 3.0V IOL = 2.1mA 0.4 V Symbol Parameter 1.7V 2.5V, 5.0V UnitsMin Max Min Max fSCL Clock Frequency, SCL 400 1000 kHz tLOW Clock Pulse Width Low 1.2 0.4 μs tHIGH Clock Pulse Width High 0.6 0.4 μs tI Noise Suppression Time(1) 100 50 ns tAA Clock Low to Data Out Valid 0.1 0.9 0.05 0.55 μs tBUF Time the bus must be free before a new transmission can start(1) 1.3 0.5 μs tHD.STA Start Hold Time 0.6 0.25 μs tSU.STA Start Set-up Time 0.6 0.25 μs tHD.DAT Data In Hold Time 0 0 μs tSU.DAT Data In Set-up Time 100 100 ns tR Inputs Rise Time(1) 0.3 0.3 μs tF Inputs Fall Time(1) 300 100 ns tSU.STO Stop Set-up Time 0.6 0.25 μs tDH Data Out Hold Time 50 50 ns tWR Write Cycle Time 5 5 ms Endurance(1) 25°C, Page Mode, 3.3V 1,000,000 Write cycles

AT24MAC402/602 [DATASHEET] Atmel-8807D-SEEPROM-AT24MAC402-602-Datasheet_082013 4. Memory Organization AT24MAC402/602, 2K Serial EEPROM: The 2-Kbit memory array is internally organized as 16 pages of 16 bytes of EEPROM each. Random word addressing requires a 8-bit data word address. EUI Address and Serial Number: The 48-bit EUI address in the AT24MAC402 and the 64-bit EUI address in the AT24MAC602 are located in the extended memory block. In addition, the serial number data is also located in the extended memory block as shown below in Figure 4-1. These EUI-48 or EUI-64 addresses are stored in a dedicated read-only EEPROM memory block located outside the standard 2K memory array as shown below. This means the full standard 2-Kbit EEPROM array is available for use as opposed to solutions where only half of the EEPROM memory array is available for application usage. Figure 4-1. Memory Organization The EUI-48 and EUI-64 address fields contain either six or eight bytes respectively. The first three bytes of the EUI read-only address field are called the Organizationally Unique Identifier (OUI) and the IEEE Registration Authority has assigned FCC23Dh as the Atmel, OUI. Following the OUI, the remaining bytes are called the Extension Identifier and will be either three bytes or five bytes depending on if it is an EUI-48 address (AT24MAC402) or EUI-64 address (AT24MAC602). Atmel generates this unique 24-bit/40-bit data value along with the OUI to guarantee a globally unique EUI address value and programs it at the factory before permanently locking the extended memory region. Standard 2-Kbit EEPROM Extended Memory Second-half Address Range (80h-FFh) EUI-48/64 Value EUI-48 Address Range (9Ah-9Fh) EUI-64 Address Range (98h-9Fh) 128-bit Serial Number Address Range (80h-8Fh) Permanent or Reversible Software Write Protection Capable or Full Array Hardware Write Protection Capable Full Array Hardware Write Protection Capable Read-only Read-only Device Address ‘1010’ Device Address ‘1011’ First-half Address Range (00h-7Fh)

7AT24MAC402/602 [DATASHEET] Atmel-8807D-SEEPROM-AT24MAC402-602-Datasheet_082013

4.1 EUI-48 Support

The EUI-48 address is stored in the last six bytes of the AT24MAC402’s extended memory block as shown in Table 4-1. For information on the protocol to read the EUI-48 value, see Section 6., “Device Addressing” on page 11 and Section 9., “Read Operations” on page 17. Table 4-1. 48-Bit EUI Address Memory Map Example Using an EUI-48 Value in an EUI-64 Application: An EUI-64 compatible value can be generated from the EUI-48 value contained in the AT24MAC402 by concatenating the 24-bit OUI, an FFFEh data value, and the 24-bit Extension Identifier. This is commonly referred to as an Encapsulated EUI-48 value. However, Atmel recommends using the AT24MAC602 which contains a true EUI-64 value so that post read processing is not required by the application.

4.2 EUI-64 Support

For applications that utilize an EUI-64 standard, the EUI-64 address is stored in the last eight bytes of the AT24MAC602’s extended memory block. Similar to EUI-48, the EUI-64 standard consists of the same three byte OUI coupled with a five byte extension identifier (Table 4-2). Atmel generates this unique 40-bit data value coupled with the OUI to guarantee a globally unique 64-bit EUI value and requires no additional data manipulation like other solutions where the application must manually insert a two byte FFFEh value in between the OUI and Extension Identifier. For information on how to read the EUI read protocol, see See Section 6., “Device Addressing” on page 11 and “Read Operations” on page 17. Table 4-2. 64-Bit EUI Address Memory Map Example Note: 1. The data values FFFEh and FFFFh are prohibited beginning from the 40-bit Extension Identifier in Byte 1 and Byte 2. These values are reserved for denoting an encapsulated MAC-48 or EUI-48 value for use in an EUI-64 environment.

4.3 Non-Atmel OUI Programming Option

For customers with their own IEEE-assigned OUI or Company ID, Atmel offers the time saving option to manage and deliver custom AT24MAC402/602 devices with their EUI-48/64 values uniquely pre-programmed at delivery. Contact your local Atmel Sales Office for additional information. 48-Bit EUI Description 24-Bit OUI 24-Bit Extension Identifier Memory Address 9Ah 9Bh 9Ch 9Dh 9Eh 9Fh EUI Data Value FCh C2h 3Dh Byte 1 Byte 2 Byte 3 64-Bit EUI Description 24-Bit OUI 40-Bit Extension Identifier Memory Address 98h 99h 9Ah 9Bh 9Ch 9Dh 9Eh 9Fh EUI Data Value FCh C2h 3Dh Byte 1(1) Byte 2(1) Byte 3 Byte 4 Byte 5

11AT24MAC402/602 [DATASHEET] Atmel-8807D-SEEPROM-AT24MAC402-602-Datasheet_082013 6. Device Addressing Standard EEPROM Access: The 2K EEPROM requires an 8-bit device address word following a start condition to enable the chip for a read or write operation (see Figure 7-1 on page 12). The device address word consists of a mandatory one-zero sequence for the first four most-significant bits ‘1010’(Ah) for normal read and write operations and ‘0110’ (6h) for writing to the Software Write Protect Register. The next three bits in the protocol sequence are the A2, A1, and A0 device address bits. These three bits must match their corresponding hard-wired input pins A2, A1, and A0 in order for the part to acknowledge. The eighth bit of the device address is the read/write operation select bit. A read operation is initiated if this bit is high, and a write operation is initiated if this bit is low. Upon a compare of the device address, the EEPROM will output a zero. If a compare is not made, the device will return to a standby state. The device will not acknowledge if the Write Protect Register has been programmed and the control code is ‘0110’(6h). Serial Number Access: The AT24MAC402/602 incorporates an extended memory block containing a factory-programmed 128-bit serial number. Access to this memory location is obtained by beginning the device address word with a ‘1011’(Bh) sequence. The behavior of the next three bits (A2, A1, and A0) remain the same as during a standard memory addressing sequence. The eighth bit of the device address needs to be set to a one to read the serial number. A zero in this bit position, other than during a dummy write sequence to set the address pointer, will result in a unknown condition and behavior. Writing or altering the 128-bit serial number is not possible as it is permanently write protected. Further specific protocol is needed to address the serial number feature of the part. For more details on accessing this special feature, See Section 9., “Read Operations” on page 17. EUI Address Access: The AT24MAC402/602 utilizes an extended memory block containing a factory-programmed read-only EUI-48 or EUI-64 address respectively. Access to this memory block is obtained by beginning the device address word with a ‘1011’ (Bh) sequence. The behavior of the next three bits (A2, A1, and A0) remain the same as during a standard memory addressing sequence. The eighth bit of the device address needs to be set to a one to read the EUI address. A zero in this bit position, other than during a dummy write sequence to set the address pointer, will result in a unknown condition and behavior. Attempting to write or alter the EUI address is not possible as it is permanently write protected. Further specific protocol is needed to address this feature of the part. For more details on accessing this special feature, see Section 9., “Read Operations”. Table 6-1. Device Address Access Area Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 EEPROM 1 0 1 0 A2 A1 A0 R/W EUI or Serial Number Read 1 0 1 1 A2 A1 A0 1

AT24MAC402/602 [DATASHEET] Atmel-8807D-SEEPROM-AT24MAC402-602-Datasheet_082013 Figure 8-3. Clearing Reversible Write Protect Register (RSWP) Table 8-1. V HV Note: V HV – VCC > 4.8V Hardware Write Protection: The WP pin can be connected to VCC, GND, or left floating. Connecting the WP pin to VCC will write protect the entire array regardless of whether or not the Software Write Protection has been enabled or invoked (see Table 8-3 on page 15 and Table 8-4 on page 16). The Software Write Protection Register cannot be programmed when the WP pin is connected to V CC. If the WP pin is connected to GND or left floating, the write protection mode is determined by the status of the Software Write Protect Register. Table 8-2. Write Protection Min Max Units VHV 7 10 V Pin Preamble R/W Command A2 A1 A0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Set PSWP A2 A1 A0 0 1 1 0 A2 A1 A0 0 Set RSWP 0 0 VHV 0 1 1 0 0 0 1 0 Clear RSWP 0 VCC VHV 0 1 1 0 0 1 1 0 0110 0 101SDA LINE Word Address DataControl Byte S T A R T S T O P A C K A C K A C K = Don’t Care

15AT24MAC402/602 [DATASHEET] Atmel-8807D-SEEPROM-AT24MAC402-602-Datasheet_082013 Table 8-3. WP Connected to GND or Floating WP Connected to GND or Floating Command R/W Bit Permanent Write Protect Register PSWP Reversible Write Protect Register RSWP Response from Device Action from Device 1010 R X X ACK Read Array. 1010 W Programmed X ACK Can write to second-half (80h - FFh) only. 1010 W X Programmed ACK Can write to second-half (80h - FFh) only. 1010 W Not Programmed Not Programmed ACK Can write to full array. Read PSWP R Programmed X No ACK STOP – Indicates Permanent Write Protect Register is programmed. Read PSWP R Not Programmed X ACK Data read out is undefined. Indicates PSWP Register is not programmed. Set PSWP W Programmed X No ACK STOP – Indicates Permanent Write Protect Register is programmed. Set PSWP W Not Programmed X ACK Program Permanent Write Protect Register (irreversible). Read RSWP R X Programmed No ACK STOP – Indicates Reversible Write Protect Register is programmed. Read RSWP R X Not Programmed ACK Data read out is undefined. Indicates RSWP Register is not programmed. Set RSWP W X Programmed No ACK STOP – Indicates Reversible Write Protect Register is programmed. Set RSWP W X Not Programmed ACK Program Reversible Write Protect Register (reversible). Clear RSWP W Programmed X No ACK STOP – Indicates Permanent Write Protect Register is programmed. Clear RSWP W Not Programmed X ACK Clear (unprogram) Reversible Write Protect Register (reversible).

AT24MAC402/602 [DATASHEET] Atmel-8807D-SEEPROM-AT24MAC402-602-Datasheet_082013 Table 8-4. WP Connected to V CC WP Connected to VCC Command R/W Bit Permanent Write Protect Register PSWP Reversible Write Protect Register RSWP Response from Device Action from Device 1010 R X X ACK Read array. 1010 W X X ACK Device is write protected. Read PSWP R Programmed X No ACK STOP – Indicates pErmanent Write Protect Register is programmed. Read PSWP R Not Programmed X ACK Data read out is undefined. Indicates PSWP Register is not programmed. Set PSWP W Programmed X No ACK STOP – Indicates Permanent Write Protect Register is programmed. Set PSWP W Not Programmed X ACK Cannot program write protect registers. Read RSWP R X Programmed No ACK STOP – Indicates Reversible Write Protect Register is programmed. Read RSWP R X Not Programmed ACK Data read out is undefined. Indicates RSWP Register is not programmed. Set RSWP W X Programmed No ACK STOP – Indicates Reversible Write Protect Register is programmed. Set RSWP W X Not Programmed ACK Cannot program write protect registers. Clear RSWP W Programmed X No ACK STOP – Indicates Permanent Write Protect Register is programmed. Clear RSWP W Not Programmed X ACK Cannot write to Write Protect Registers.

AT24MAC402/602 [DATASHEET] Atmel-8807D-SEEPROM-AT24MAC402-602-Datasheet_082013 Checking the Permanent Write Protect Register (PSWP) Status: Determining the status of the Permanent Write Protect Register can be accomplished by sending a similar command to the device as was used when programming the register, except the R/W bit must be set to one. If the device responds with an acknowledge, the Permanent Write Protect Register has not been programmed; otherwise, it has been programmed and the first-half of the array is permanently write protected. Checking the Reversible Write Protect Register (RSWP) Status: Determining the status of the Reversible Write Protect Register can be accomplished by sending a similar command to the device as was used when programming the register, except the R/W bit must be set to one. If the device returns an acknowledge, the Reversible Write Protect Register has not been programmed; otherwise, it has been programmed and the first-half of the array is write protected, but remains reversible. Table 9-1. PSWP and RSWP Status Pin Preamble R/W Command A2 A1 A0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Read PSWP A2 A1 A0 0 1 1 0 A2 A1 A0 1 Read RSWP 0 0 A0 0 1 1 0 0 0 1 1

21AT24MAC402/602 [DATASHEET] Atmel-8807D-SEEPROM-AT24MAC402-602-Datasheet_082013 10. Ordering Information

10.1 Ordering Code Detail

24M A C 042S S–AT Atmel Designator Product Family EUI Option 4 = EUI-48 Standard 6 = EUI-64 Standard Package Option SS = JEDEC SOIC X = TSSOP MA = UDFN ST = SOT23 WWU = Wafer Unsawn M Operating Voltage M = 1.7V to 5.5V H Package Device Grade or Wafer/Die Thickness H = Green, NiPdAu Lead Finish, Industrial Temperature Range, (-40°C to +85°C) U = Green, Matte Sn Lead Finish, Industrial Temperature Range, (-40°C to +85°C) 11 = 11 mil Wafer Thickness Shipping Carrier Option Device Density 02 = 2-Kbit Density 24MAC = I2C-compatible Serial EEPROM with EUI Address Feature with 128-bit Serial Number Feature B = Bulk (Tubes) T = Tape and Reel

AT24MAC402/602 [DATASHEET] Atmel-8807D-SEEPROM-AT24MAC402-602-Datasheet_082013

10.2 AT24MAC402/602 Ordering Codes

Programming of IEEE assigned customer OUIs (non-Atmel OUIs) in conjunction with specific blocks of EUI-48 (AT24MAC402) or EUI-64 (AT24MAC602) values is available. Please contact Atmel for more details. Additional package types that are not listed may be available. Please contact Atmel for more details. Notes: 1. Consistent with the general semiconductor market trend, Atmel will supply devices with either gold or copper bond wires to increase manufacturing flexibility and to ensure a long-term continuity of supply. There is no difference in product quality, reliability, or performance between the two variations. 2. B = Bulk delivery in tubes:  SOIC and TSSOP = 100 units per tube. 3. T = Tape and reel:  SOIC = 4,000 per reel.  TSSOP, UDFN, and SOT23 = 5,000 per reel. 4. For wafer sales, please contact Atmel Sales. Atmel Ordering Codes(1) Finish Package Voltage Operation Range AT24MAC402-SSHM-B(2) NiPdAu (Lead-free/Halogen-free) 8S1 1.7V to 5.5V Industrial Temperature (-40°C to 85°C) AT24MAC402-SSHM-T(3) AT24MAC402-XHM-B(2) AT24MAC402-XHM-T(3) AT24MAC402-MAHM-T(3) 8MA2 AT24MAC402-STUM-T(3) Matte Tin (Lead-free/Halogen-free) 5TS1 AT24MAC402-WWU11M(4) — Wafer Sale AT24MAC602-SSHM-B(2) NiPdAu (Lead-free/Halogen-free) 8S1 1.7V to 5.5V Industrial Temperature (-40°C to 85°C) AT24MAC602-SSHM-T(3) AT24MAC602-XHM-B(2) AT24MAC602-XHM-T(3) AT24MAC602-MAHM-T(3) 8MA2 AT24MAC602-STUM-T(3) Matte Tin (Lead-free/Halogen-free) 5TS1 AT24MAC602-WWU11M(4) — Wafer Sale Package Type 8S1 8-lead, 0.150" wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8X 8-lead, 0.170" wide, Thin Shrink Small Outline (TSSOP) 8MA2 8-pad, 2.00mm x 3.00mm body, 0.50mm pitch, Ultra Thin Dual No Lead (UDFN) 5TS1 5-lead, 2.90mm x 1.60mm body, Plastic Thin Shrink Small Outline (SOT23)

23AT24MAC402/602 [DATASHEET] Atmel-8807D-SEEPROM-AT24MAC402-602-Datasheet_082013 11. Part Markings DRAWING NO. REV. TITLE Catalog Number Truncation AT24MAC402 Truncation Code ##: P4 AT24MAC602 Truncation Code ##: P6 AAAAAAAA ## M @ ATMLHYWW 8-lead SOIC 8-lead TSSOP AAAAAAA ## M @ ATHYWW 8-lead UDFN HM@ YXX 2.0 x 3.0 mm Body 5-lead SOT-23 ## MU YMXX Bottom Mark Top Mark Note 2: Package drawings are not to scale Note 1: designates pin 1 Package Mark Contact: DL-CSO-Assy_eng@atmel.com 24MAC402-602CSM C 4/3/12 24MAC402-602SM, AT24MAC402 and AT24MAC602 Package Marking Information Date Codes Voltages Y = Year M = Month WW = Work Week of Assembly M: 1.7V min 2: 2012 6: 2016 A: January 02: Week 2 3: 2013 7: 2017 B: February 04: Week 4 5: 2015 9: 2019 L: December 52: Week 52 Country of Assembly Lot Number Grade/Lead Finish Material @ = Country of Assembly AAA...A = Atmel Wafer Lot Number H: Industrial/NiPdAu U: Industrial/Matte Tin Trace Code Atmel Truncation XX = Trace Code (Atmel Lot Numbers Correspond to Code) AT: Atmel Example: AA, AB.... YZ, ZZ ATM: Atmel ATML: Atmel AT24MAC402 and AT24MAC602: Package Marking Information

AT24MAC402/602 [DATASHEET] Atmel-8807D-SEEPROM-AT24MAC402-602-Datasheet_082013 12. Packaging Information 12.1 8S1 — 8-lead JEDEC SOIC DRAWING NO. REV. TITLE GPC COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 A 1.35 – 1.75 b 0.31 – 0.51 C 0.17 – 0.25 D 4.80 – 5.05 E1 3.81 – 3.99 E 5.79 – 6.20 e 1.27 BSC L 0.40 – 1.27 ØØ 0° – 8° Ø E N TOP VIEW C END VIEW A b L e D SIDE VIEW Package Drawing Contact: packagedrawings@atmel.com 8S1 G 6/22/11 Notes: This drawing is for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 8S1, 8-lead (0.150” Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) SWB

25AT24MAC402/602 [DATASHEET] Atmel-8807D-SEEPROM-AT24MAC402-602-Datasheet_082013 12.2 8X — 8-lead TSSOP DRAWING NO. REV. TITLE GPC COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A - - 1.20 A1 0.05 - 0.15 A2 0.80 1.00 1.05 D 2.90 3.00 3.10 2, 5 E 6.40 BSC E1 4.30 4.40 4.50 3, 5 b 0.19 0.25 0.30 4 e 0.65 BSC L 0.45 0.60 0.75 L1 1.00 REF C 0.09 - 0.20 Side View End ViewTop View A L D N b Pin 1 indicator this corner E e Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15mm (0.006in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25mm (0.010in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07mm. 5. Dimension D and E1 to be determined at Datum Plane H. Package Drawing Contact: packagedrawings@atmel.com 8X E 2/27/14 8X, 8-lead 4.4mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) TNR C

AT24MAC402/602 [DATASHEET] Atmel-8807D-SEEPROM-AT24MAC402-602-Datasheet_082013 12.3 8MA2 — 8-pad UDFN DRAWING NO. REV. TITLE GPC 8MA2 F 6/6/14 8MA2, 8-pad 2 x 3 x 0.6mm Body, Thermally Enhanced Plastic Ultra Thin Dual Flat No-Lead Package (UDFN) YNZ COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A 0.50 0.55 0.60 A1 0.0 0.02 0.05 A2 - - 0.55 D 1.90 2.00 2.10 D2 1.20 - 1.60 E 2.90 3.00 3.10 E2 1.20 - 1.60 b 0.18 0.25 0.30 3 C 1.52 REF L 0.30 0.35 0.40 e 0.50 BSC K 0.20 - - TOP VIEW SIDE VIEW BOTTOM VIEW Package Drawing Contact: packagedrawings@atmel.com C E Pin 1 ID D A e (6x) L (8x) b (8x) Pin#1 ID K Notes: 1. This drawing is for general information only. Refer to Drawing MO-229, for proper dimensions, tolerances, datums, etc. 2. The Pin #1 ID is a laser-marked feature on Top View. 3. Dimensions b applies to metallized terminal and is measured between 0.15 mm and 0.30 mm from the terminal tip. If the terminal has the optional radius on the other end of the terminal, the dimension should not be measured in that radius area. 4. The Pin #1 ID on the Bottom View is an orientation feature on the thermal pad.

27AT24MAC402/602 [DATASHEET] Atmel-8807D-SEEPROM-AT24MAC402-602-Datasheet_082013 12.4 5TS1 — 5-lead SOT23 DRAWING NO. REV. TITLE GPC Package Drawing Contact: packagedrawings@atmel.com 5TS1 D 5/31/12 5TS1, 5-lead 1.60mm Body, Plastic Thin Shrink Small Outline Package (Shrink SOT) TSZ COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A - - 1.00 A1 0.00 - 0.10 A2 0.70 0.90 1.00 c 0.08 - 0.20 3 D 2.90 BSC 1,2 E 2.80 BSC 1,2 E1 1.60 BSC 1,2 L1 0.60 REF e 0.95 BSC e1 1.90 BSC b 0.30 - 0.50 3,4 1. Dimension D does not include mold flash, protrusions or gate burrs. Mold flash, protrusions or gate burrs shall not exceed 0.15 mm per end. Dimension E1 does not include interlead flash or protrusion. Interlead flash or protrusion shall not exceed 0.15 mm per side. 2. The package top may be smaller than the package bottom. Dimensions D and E1 are determined at the outermost extremes of the plastic body exclusive of mold flash, tie bar burrs, gate burrs and interlead flash, but including any mismatch between the top and bottom of the plastic body. 3. These dimensions apply to the flat section of the lead between 0.08 mm and 0.15 mm from the lead tip. 4. Dimension "b" does not include dambar protrusion. Allowable dambar protrusion shall be 0.08 mm total in excess of the "b" dimension at maximum material condition. The dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and an adjacent lead shall not be less than 0.07 mm. This drawing is for general information only. Refer to JEDEC Drawing MO-193, Variation AB for additional information. 5 4 L C END VIEW C AA2 b e PLANE SEATING D SIDE VIEW E TOP VIEW

AT24MAC402/602 [DATASHEET] Atmel-8807D-SEEPROM-AT24MAC402-602-Datasheet_082013 13. Revision History Doc. Rev. Date Description 8808D 08/2014 Add bulk SOIC and TSSOP ordering codes. Update ordering code table, 8X and 8MA2 package drawings, and the disclaimer page. Correct pinouts from bottom to top view and reorganization figures. No changes to functional specification. 8807C 07/2013 Update status from preliminary to release. Update footers and disclaimer page. 8807B 09/2012 Update ordering information. 8807A 06/2012 Initial document release.

Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 | www.atmel.com © 2014 Atmel Corporation. / Rev.: Atmel-8807D-SEEPROM-AT24MAC402-602-Datasheet_082013. Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®,and others are registered trademarks or trademarks of Atmel Corporation in U.S. and other countries. Other terms and product names may be trademarks of others. DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDIT IONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS P RODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMI TATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or c ompleteness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel d oes not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automo tive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical A pplications”) without an Atmel officer's specific written consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for t he operation of nuclear facilities and weapons systems. Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.