AT24HC04B ATMEL
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 19
Technical content
Features
- Write Protect Pin for Hardware Data Protection – Utilizes Different Array Protection Compared to the AT24C04B Low-voltage and Standard-voltage Operation – 1.8 (V CC = 1.8V to 5.5V) Internally Organized 512 x 8 (4K) Two-wire Serial Interface Schmitt Trigger, Filtered Inputs for Noise Suppression Bidirectional Data Transfer Protocol 1 MHz (5V) and 400 kHz (1.8V, 2.5V, 2.7V) Clock Rate 16-byte Page Partial Page Writes Allowed Self-timed Write Cycle (5 ms Max) High Reliability – Endurance: One Million Write Cycles – Data Retention: 100 Years 8-lead PDIP, 8-lead JEDEC SOIC and 8-lead TSSOP Packages Die Sales: Wafer Form, Tape and Reel, and Bumped Wafers
Description
The AT24HC04B provides 4096 bits of seri al electrically erasable and programmable read-only memory (EEPROM) organized as 5 12 words of 8 bits each. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. The AT24HC04B is available in space-saving 8-lead PDIP, 8-lead JEDEC SOIC and 8-lead TSSOP packages and is accessed via a two-wire serial interface. In addition, the entire family is available in 1.8V (1.8V to 5.5V) version. Table 0-1. Pin Configuration Pin Name Function A1, A2 Address Inputs SDA Serial Data SCL Serial Clock Input WP Write Protect NC No-connect Two-wire Serial EEPROM 4K (512 x 8) AT24HC04B 5227E–SEEPR–11/08 NC GND VCC WP SCL SDA 8-lead PDIP NC GND VCC WP SCL SDA 8-lead SOIC NC GND VCC WP SCL SDA 8-lead TSSOP
5227E–SEEPR–11/08 AT24HC04B Figure 0-1. Block Diagram Absolute Maximum Ratings* Maximum Ratings” may cause permanent dam- age to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Voltage on Any Pin START STOP LOGIC VCC GND WP SCL SDA SERIAL CONTROL LOGIC EN H.V. PUMP/TIMING EEPROM DATA RECOVERY SERIAL MUX X DEC DOUT/ACK LOGIC COMP LOAD INC DATA WORD ADDR/COUNTER Y DEC R/W DOUT DIN LOAD DEVICE ADDRESS COMPARATOR
5227E–SEEPR–11/08 AT24HC04B 1. Pin Description SERIAL CLOCK (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative edge clock data out of each device. SERIAL DATA (SDA): The SDA pin is bidirectional for seri al data transfer. This pin is open- drain driven and may be wire-ORed with any number of other open-drain or open collector devices. DEVICE/PAGE ADDRESSES (A2, A1, A0): The A2 and A1 pins are device address inputs that must be hardwired for the AT24HC04B. As many as four 4K devices may be addressed on a single bus system. The A0 pin is a no-connect. (Device addressing and Page addressing are discussed in detail under Device Addressing and Page Addressing, page 8). WRITE PROTECT (WP): The AT24HC04B has a WP pin that provides hardware data protec- tion. The WP pin allows normal read/write operations when connected to ground (GND). When the WP pin is connected to VCC, the write protection feature is enabled and operates as shown. Table 1-1. Write Protect WP Pin Status Part of the Array Protected 24HC04B At VCC Upper Half (2K) Array At GND Normal Read/Write Operations
5227E–SEEPR–11/08 AT24HC04B 2. Memory Organization AT24HC04B, 4K SERIAL EEPROM: The 4K is internally organized with 32 pages of 16 bytes each. Random word addressing requires an 9-bit data word address. Note: 1. This parameter is characterized and is not 100% tested. Note: 1. V IL min and VIH max are reference only and are not tested. Table 2-1. Pin Capacitance(1) Applicable over recommended operating range from TAI = 25°C, f = 1.0 MHz, VCC = +1.8V Symbol Test Condition Max Units Conditions CI/O Input/Output Capacitance (SDA) 8 pF V I/O = 0V CIN Input Capacitance (A0, A1, A2, SCL) 6 pF V IN = 0V Table 2-2. DC Characteristics Applicable over recommended operating range from: TAI = −40°C to +85°C, VCC = +1.8V to +5.5V (unless otherwise noted) Symbol Parameter Test Condition Min Typ Max Units VCC1 Supply Voltage 1.8 5.5 V VCC2 Supply Voltage 2.5 5.5 V VCC3 Supply Voltage 2.7 5.5 V VCC4 Supply Voltage 4.5 5.5 V ICC Supply Current VCC = 5.0V READ at 100 kHz 0.4 1.0 mA ICC Supply Current VCC = 5.0V WRITE at 100 kHz 2.0 3.0 mA ISB1 Standby Current VCC = 1.8V V IN = VCC or VSS 0.6 3.0 µA ISB2 Standby Current VCC = 2.5V V IN = VCC or VSS 1.4 4.0 µA ISB3 Standby Current VCC = 2.7V V IN = VCC or VSS 1.6 4.0 µA ISB4 Standby Current VCC = 5.0V V IN = VCC or VSS 8.0 18.0 µA ILI Input Leakage Current V IN = VCC or VSS 0.10 3.0 µA ILO Output Leakage Current V OUT = VCC or VSS 0.05 3.0 µA VIL Input Low Level (1) −0.6 V CC x 0.3 V VIH Input High Level (1) VCC x 0.7 V CC + 0.5 V VOL2 Output Low Level VCC = 3.0V I OL = 2.1 mA 0.4 V VOL1 Output Low Level VCC = 1.8V I OL = 0.15 mA 0.2 V
5227E–SEEPR–11/08 AT24HC04B Note: 1. This parameter is ensured by characterization only. Table 2-3. AC Characteristics Applicable over recommended operating range from T AI = –40°C to +85°C, VCC = +1.8V to +5.5V, CL = 1 TTL Gate and 100 pF (unless otherwise noted) Symbol Parameter UnitsMin Max Min Max fSCL Clock Frequency, SCL 400 1000 kHz tLOW Clock Pulse Width Low 1.2 0.4 µs tHIGH Clock Pulse Width High 0.6 0.4 µs tI Noise Suppression Time 50 40 ns tAA Clock Low to Data Out Valid 0.1 0.9 0.05 0.55 µs tBUF Time the bus must be free before a new transmission can start 1.2 0.5 µs tHD.STA Start Hold Time 0.6 0.25 µs tSU.STA Start Setup Time 0.6 0.25 µs tHD.DAT Data In Hold Time 0 0 µs tSU.DAT Data In Setup Time 100 100 ns tR Inputs Rise Time(1) 0.3 0.3 µs tF Inputs Fall Time(1) 300 100 ns tSU.STO Stop Setup Time 0.6 .25 µs tDH Data Out Hold Time 50 50 ns tWR Write Cycle Time 5 5 ms Endurance(1) 5.0V, 25°C, Byte Mode 1 Million Write Cycles
5227E–SEEPR–11/08 AT24HC04B Figure 3-6. Output Acknowledge 4. Device Addressing and Page Addressing The 4K EEPROM device requires an 8-bit device address word following a start condition to enable the chip for a read or write operation, as shown in Figure 4-1. Figure 4-1. Device Address The device address word consists of a mandatory “1”, “0” sequence for the first four most signif- icant bits as shown. This is common to all the EEPROM devices. The next two bits are the A2 and A1 device address bits for the 4K EEPROM. These two bits must compare to their corresponding hardwired input pins. The A0 pin is a no-connect. The next bit is the memory page address bit. This bit is the MSB of the 9-bit data word address. The eighth bit of the device address is the read/write operation select bit. A read operation is ini- tiated if this bit is high, and a write operation is initiated if this bit is low. Upon a compare of the device address, the EEPROM will output a “0”. If a compare is not made, the chip will return to a standby state. SCL DATA IN DATA OUT START ACKNOWLEDGE 981 MSB LSB
1 A 2 P0 A 1 R/W 0 0 1
5227E–SEEPR–11/08 AT24HC04B the data word address and serially clock out sequential data words. When the memory address limit is reached, the data word address will “roll over” and the sequential read will continue. The sequential read operation is terminated when the microcontroller does not respond with a “0” but does generate a following stop condition, see Figure 6-3. Figure 6-3. Sequential Read
5227E–SEEPR–11/08 AT24HC04B Notes: 1. “-B” denotes bulk. 2. “-T” denotes tape and reel. SOIC = 4K per reel. TSSOP = 5K per reel. 3. Available in tape and reel and wafer form; order as SL788 for inkless wafer form. Bumped die available upon request. Please contact Serial Interface Marketing. 7. AT24HC04B Ordering Information Ordering Code Voltage Package Operation Range AT24HC04B-PU (Bulk form only) 1.8 8P 3 Lead-free/Halogen-free/ Industrial Temperature (−40°C to 85°C) AT24HC04BN-SH-B(1) (NiPdAu Lead Finish) 1.8 8S1 AT24HC04BN-SH-T(2) (NiPdAu Lead Finish) 1.8 8S1 AT24HC04B-TH-B(1) (NiPdAu Lead Finish) 1.8 8A2 AT24HC04B-TH-T(2) (NiPdAu Lead Finish) 1.8 8A2 AT24HC04B-W-11(3) 1.8 Die Sale Industrial Temperature (−40°C to 85°C) Package Type 8P3 8-pin, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Options −1.8 Low Voltage (1.8V to 5.5V)
5227E–SEEPR–11/08 AT24HC04B 8. Part marking scheme 8-PDIP 8-SOIC TOP MARK Seal Year Y = SEAL YEAR WW = SEAL WEEK | Seal Week 6: 2006 0: 2010 02 = Week 2 | | | 7: 2007 1: 2011 04 = Week 4 A T M L U Y W W 9: 2009 3: 2013 :: : :::: :: H 4 B 1 52 = Week 52 * Lot Number Lot Number to Use ALL Characters in Marking | BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark TOP MARK Seal Year Y = SEAL YEAR WW = SEAL WEEK | Seal Week 6: 2006 0: 2010 02 = Week 2 | | | 7: 2007 1: 2011 04 = Week 4 A T M L H Y W W 9: 2009 3: 2013 :: : :::: :: H 4 B 1 52 = Week 52 * Lot Number Lot Number to Use ALL Characters in Marking | BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark
5227E–SEEPR–11/08 AT24HC04B 8-TSSOP TOP MARK Pin 1 Indicator (Dot) Y = SEAL YEAR WW = SEAL WEEK | 6: 2006 0: 2010 02 = Week 2 H 4 B 1 50 = Week 50 BOTTOM MARK X X XX = COUNTRY OF ORIGIN A A A A A A A <- Pin 1 Indicator TOP MARK Seal Year Y = SEAL YEAR WW = SEAL WEEK
5227E–SEEPR–11/08 AT24HC04B 9. Packaging Information 8P3 – PDIP
2325 Orchard Parkway
San Jose, CA 95131 TITLE DRAWING NO. R REV. 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) 01/09/02 8P3 B Notes: 1. Thi s drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA, for additional information. 2. Dimen sions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or ro unded lead tips are preferred to ease insertion. COMMON DIMENSIONS (Unit of Measure = inches) SYMBOL MIN NOM MAX NOTE D E e Lb2 b A2 A N eA c
4 PLCS
A – – 0.210 2 A2 0.115 0.130 0.195 b 0.014 0.01 8 0.022 5 b2 0.045 0.060 0.070 6 b3 0.030 0.039 0.045 6 c 0.00 8 0.010 0.014 D 0.355 0.365 0.400 3 D1 0.005 – – 3 E 0.300 0.310 0.325 4 E1 0.240 0.250 0.2 80 3 e 0.100 B SC eA 0.300 B SC 4 L 0.115 0.130 0.150 2 Top View Side View End View
5227E–SEEPR–11/08 AT24HC04B 8S1 – JEDEC SOIC 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. Note: 10/7/03 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) 8S1 B COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. A 1.35 – 1.75 b 0.31 – 0.51 C 0.17 – 0.25 D 4. 80 – 5.00 E1 3. 81 – 3.99 E 5.79 – 6.20 e 1.27 B SC L 0.40 – 1.27 ∅ 0° – 8° Top View End View Side View e B D A N E C L
5227E–SEEPR–11/08 AT24HC04B 8A2 – TSSOP San Jose, CA 95131 TITLE DRAWING NO. R REV. 5/30/02 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 2.90 3.00 3.10 2, 5 E 6.40 B SC E1 4.30 4.40 4.50 3, 5 A – – 1.20 A2 0. 80 1.00 1.05 b 0.19 – 0.30 4 e 0.65 B SC L 0.45 0.60 0.75 L1 1.00 REF 8A2, 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Notes: 1. Thi s drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, d atums, etc. 2. Dimen sion D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimen sion E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimen sion b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protr usion and adjacent lead is 0.07 mm. 5. Dimen sion D and E1 to be determined at Datum Plane H. 8A2 B Side View End ViewTop View A L D 123 N b Pin 1 indicator this corner E e
5227E–SEEPR–11/08 AT24HC04B
Revision History
Doc. Rev. Date Comments 5227E 11/2008 Updated pin configurations 5227D 1/2008 Removed ‘preliminary’ status 5227C 8/2007 Added Part Marking Scheme 5227B 8/2007 Updated to new template Updated Common figures Added Part Marking tables 5227A 4/2007 Initial document release.
5227E–SEEPR–11/08 Headquarters International Atmel Corporation San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Room 1219 Chinachem Golden Plaza
77 Mody Road Tsimshatsui
Tel: (852) 2721-9778 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309
78054 Saint-Quentin-en-
9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Product Contact Web Site www.atmel.com Technical Support s_eeprom@atmel.com Sales Contact www.atmel.com/contacts Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL ’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL ’S WEB SITE, ATMEL ASSUMES NO LI ABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTOR Y WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICU LAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR I NCIDEN- TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATME L HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or comp leteness of the contents of this document and reserves the rig ht to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained her ein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not int ended, authorized, or warranted for use as components in applications in tended to support or sustain life. © 2008 Atmel Corporation . All rights reserved. Atmel ®, Atmel logo and combinations thereof, and others, are registered trademarks or trade- marks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.