DATASHEET SEARCH SITE

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 18

Technical content

Features

 Write Protect Pin for Hardware Data Protection ̶ Utilizes Different Array Protection Compared to the AT24C04B  Low-voltage and Standard-voltage Operation ̶ 1.8V (VCC = 1.8V to 5.5V)  Internally Organized 512 x 8 (4K)  2-Wire Serial Interface  Schmitt Trigger, Filtered Inputs for Noise Suppression  Bidirectional Data Transfer Protocol  1MHz (5V) and 400kHz (1.8V, 2.5V, 2.7V) Clock Rate  16-byte Page  Partial Page Writes Allowed  Self-timed Write Cycle (5ms Max)  High Reliability ̶ Endurance: 1,000,000 Write Cycles ̶ Data Retention: 100 Years  8-lead PDIP, 8-lead JEDEC SOIC, and 8-lead TSSOP Packages  Die Sales: Wafer Form, Tape and Reel, and Bumped Wafers

Description

The AT24HC04B provides 4096 bits of Serial Electrically Erasable and Programmable Read-Only Memory (EEPROM) organized as 512 words of 8 bits each. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. The AT24HC04B is available in space-saving 8-lead PDIP, 8-lead JEDEC SOIC, and 8-lead TSSOP packages and is accessed via a 2-wire serial interface. In addition, the entire family is available in 1.8V (1.8V to 5.5V) version. AT24HC04B I2C-Compatible (2-Wire) Serial EEPROM 4K (512 x 8) DATASHEET

AT24HC04B [DATASHEET] Atmel-5227F-SEEPROM-AT24HC04B-Datasheet_022014 1. Pin Configurations and Pinouts Table 1-1. Pin Configuration 2. Absolute Maximum Ratings* Pin Name Function NC No Connect A1 and A2 Address Inputs SDA Serial Data SCL Serial Clock Input WP Write Protect VCC Device Power Supply NC GND V CC WP SCL SDA 8-lead PDIP Note: Drawings are not to scale. Top ViewTop View Top View 8-lead TSSOP NC GND V CC WP SCL SDA 8-lead SOIC NC GND V CC WP SCL SDA Voltage on Any Pin *Notice: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

3AT24HC04B [DATASHEET] Atmel-5227F-SEEPROM-AT24HC04B-Datasheet_022014 3. Block Diagram Figure 3-1. Block Diagram 4. Pin Description Serial Clock (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative edge clock data out of each device. Serial Data (SDA): The SDA pin is bidirectional for serial data transfer. This pin is open-drain driven and may be wire-ORed with any number of other open-drain or open collector devices. Device/Page Addresses (A2, A1, and A0): The A2 and A1 pins are device address inputs that must be hardwired for the AT24HC04B. As many as four 4K devices may be addressed on a single bus system. The A0 pin is a no connect. (Device addressing and Page addressing are discussed in detail in Section 7., “Device Addressing and Page Addressing”). Write Protect (WP): The AT24HC04B has a WP pin which provides hardware data protection. The WP pin allows normal read/write operations when connected to ground (GND). When the WP pin is connected to V CC, the write protection feature is enabled and operates as shown. Table 4-1. Write Protect START STOP LOGIC VCC GND WP SCL SDA SERIAL CONTROL LOGIC EN H.V. PUMP/TIMING EEPROM DATA RECOVERY SERIAL MUX X DEC DOUT/ACK LOGIC COMP LOAD INC DATA WORD ADDR/COUNTER Y DEC R/W DOUT DIN LOAD DEVICE ADDRESS COMPARATOR WP Pin Status Part of the Array Protected At VCC Upper Half (2K) Array At GND Normal Read/Write Operations

AT24HC04B [DATASHEET] Atmel-5227F-SEEPROM-AT24HC04B-Datasheet_022014 5. Memory Organization AT24HC04B, 4K Serial EEPROM: The 4K is internally organized with 32 pages of 16 bytes each. Random word addressing requires an 9-bit data word address.

5.1 Pin Capacitance (1)

Note: 1. This parameter is characterized and is not 100% tested.

5.2 DC Characteristics

Note: 1. V IL min and VIH max are reference only and are not tested. Applicable over recommended operating range from TAI = 25C, f = 1.0MHz, VCC = +1.8V Symbol Test Condition Max Units Conditions CI/O Input/Output Capacitance (SDA) 8 pF VI/O = 0V CIN Input Capacitance (A0, A1, A2, and SCL) 6 pF VIN = 0V Applicable over recommended operating range from: TAI = -40C to +85C, VCC = +1.8V to +5.5V (unless otherwise noted) Symbol Parameter Test Condition Min Typ Max Units VCC1 Supply Voltage 1.80 5.50 V VCC2 Supply Voltage 2.50 5.50 V VCC3 Supply Voltage 2.70 5.50 V VCC4 Supply Voltage 4.50 5.50 V ICC Supply Current VCC = 5.0V Read at 100kHz 0.40 1 mA ICC Supply Current VCC = 5.0V Write at 100kHz 2 3 mA ISB1 Standby Current VCC = 1.8V VIN = VCC or VSS 0.60 3 μA ISB2 Standby Current VCC = 2.5V VIN = VCC or VSS 1.40 4 μA ISB3 Standby Current VCC = 2.7V VIN = VCC or VSS 1.60 4 μA ISB4 Standby Current VCC = 5.0V VIN = VCC or VSS 8 18 μA ILI Input Leakage Current VIN = VCC or VSS 0.10 3 μA ILO Output Leakage Current VOUT = VCC or VSS 0.05 3 μA VIL Input Low Level (1) 0.60 VCC x 0.30 V VIH Input High Level (1) VCC x 0.70 VCC + 0.50 V VOL2 Output Low Level VCC = 3.0V IOL = 2.10mA 0.40 V VOL1 Output Low Level VCC = 1.8V IOL = 0.15mA 0.20 V

5AT24HC04B [DATASHEET] Atmel-5227F-SEEPROM-AT24HC04B-Datasheet_022014 Table 5-1. AC Characteristics Notes: 1. This parameter is ensured by characterization only. 2. AC measurement conditions:  RL (connects to VCC): 1.3k (2.5V, 5.5V), 10k (1.7V)  Input pulse voltages: 0.3VCC to 0.7VCC  Input rise and fall times:  50ns  Input and output timing reference voltages: 0.5 x VCC Applicable over recommended operating range from TAI = –40C to +85C, VCC = +5.5V, CL = 1 TTL Gate and 100pF (unless otherwise noted). Test conditions are listed in Note 2. Symbol Parameter Min Max Min Max Units fSCL Clock Frequency, SCL 400 1000 kHz tLOW Clock Pulse Width Low 1.20 0.40 μs tHIGH Clock Pulse Width High 0.60 0.40 μs tI Noise Suppression Time 50 40 ns tAA Clock Low to Data Out Valid 0.10 0.90 0.05 0.55 μs tBUF Time the bus must be free before a new transmission can start. 1.20 0.50 μs tHD.STA Start Hold Time 0.60 0.25 μs tSU.STA Start Setup Time 0.60 0.25 μs tHD.DAT Data In Hold Time 0 0 μs tSU.DAT Data In Setup Time 100 100 ns tR Inputs Rise Time (1) 0.30 0.30 μs tF Inputs Fall Time (1) 300 100 ns tSU.STO Stop Setup Time 0.60 .25 μs tDH Data Out Hold Time 50 50 ns tWR Write Cycle Time 5 5 ms Endurance(1) 5.0V, 25C, Byte Mode 1,000,000 Write Cycles

AT24HC04B [DATASHEET] Atmel-5227F-SEEPROM-AT24HC04B-Datasheet_022014 10. Ordering Code Information Notes: 1. B = Bulk 2. T = Tape and reel  SOIC = 4K per reel  TSSOP = 5K per reel 3. Available in tape and reel and wafer form; order as SL788 for inkless wafer form. Bumped die available upon request. Please contact the Atmel sales office. Ordering Code Lead Finish Package Voltage Operation Range AT24HC04B-PU Bulk Form Only (Lead-free/Halogen-free) 8P3 1.8V Industrial Temperature (40C to 85C) AT24HC04BN-SH-B (1) NiPdAu (Lead-free/Halogen-free) 8S1 AT24HC04BN-SH-T (2) AT24HC04B-TH-B (1) AT24HC04B-TH-T (2) AT24HC04B-W-11 (3) — Die Sale Package Type 8P3 8-pin, 0.30” wide, Plastic Dual Inline (PDIP) 8S1 8-lead, 0.15” wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8X 8-lead, 4.40mm body, Plastic Thin Shrink Small Outline (TSSOP)

13AT24HC04B [DATASHEET] Atmel-5227F-SEEPROM-AT24HC04B-Datasheet_022014 11. Part Marking Scheme DRAWING NO. REV. TITLE 24HC04BSM A 1/16/14 DL-CSO-Assy_eng@atmel.com AAAAAAAA###% @ATMLHYWW 8-lead SOIC 8-lead TSSOP AAAAAAA ###% @ ATHYWW Note 2: Package drawings are not to scale Note 1: designates pin 1 AT24HC04B: Package Marking Information Catalog Number Truncation AT24HC04B Truncation Code ###: H4B Date Codes Voltages Y = Year M = Month WW = Work Week of Assembly % = Minimum Voltage 4: 2014 8: 2018 A: January 02: Week 2 L: 1.8V min 5: 2015 9: 2019 B: February 04: Week 4 7: 2017 1: 2021 L: December 52: Week 52 Country of Assembly Lot Number Grade/Lead Finish Material @ = Country of Assembly AAA...A = Atmel Wafer Lot Number H: Industrial/NiPdAu U: Industrial/Matte Tin/SnAgCu Trace Code Atmel Truncation XX = Trace Code (Atmel Lot Numbers Correspond to Code) AT: Atmel Example: AA, AB.... YZ, ZZ ATM: Atmel ATML: Atmel AAAAAAAA ###M @ATMLUYWW 8-lead PDIP

AT24HC04B [DATASHEET] Atmel-5227F-SEEPROM-AT24HC04B-Datasheet_022014 12. Packaging Information 12.1 8P3 — 8-lead PDIP DRAWING NO. REV. TITLE GPC Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information. 2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion. COMMON DIMENSIONS (Unit of Measure = inches) SYMBOL MIN NOM MAX NOTE D E e Lb2 b A2 A N eA c

4 PLCS

A 0.210 2 A2 0.115 0.130 0.195 b 0.014 0.018 0.022 5 b2 0.045 0.060 0.070 6 b3 0.030 0.039 0.045 6 c 0.008 0.010 0.014 D 0.355 0.365 0.400 3 D1 0.005 3 E 0.300 0.310 0.325 4 E1 0.240 0.250 0.280 3 e 0.100 BSC eA 0.300 BSC 4 L 0.115 0.130 0.150 2 Top View Side View End View Package Drawing Contact: packagedrawings@atmel.com 8P3 D 06/21/11 8P3, 8-lead, 0.300” Wide Body, Plastic Dual In-line Package (PDIP) PTC

15AT24HC04B [DATASHEET] Atmel-5227F-SEEPROM-AT24HC04B-Datasheet_022014 12.2 8S1 — 8-lead JEDEC SOIC DRAWING NO. REV. TITLE GPC COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 A 1.35 – 1.75 b 0.31 – 0.51 C 0.17 – 0.25 D 4.80 – 5.05 E1 3.81 – 3.99 E 5.79 – 6.20 e 1.27 BSC L 0.40 – 1.27 ØØ 0° – 8° Ø E N TOP VIEW C END VIEW A b L e D SIDE VIEW Package Drawing Contact: packagedrawings@atmel.com 8S1 G 6/22/11 Notes: This drawing is for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 8S1, 8-lead (0.150” Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) SWB

AT24HC04B [DATASHEET] Atmel-5227F-SEEPROM-AT24HC04B-Datasheet_022014 12.3 8X — 8-lead TSSOP DRAWING NO. REV. TITLE GPC COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A - - 1.20 A1 0.05 - 0.15 A2 0.80 1.00 1.05 D 2.90 3.00 3.10 2, 5 E 6.40 BSC E1 4.30 4.40 4.50 3, 5 b 0.19 – 0.30 4 e 0.65 BSC L 0.45 0.60 0.75 L1 1.00 REF C 0.09 - 0.20 Side View End ViewTop View A L D N b Pin 1 indicator this corner E e Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15mm (0.006in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25mm (0.010in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07mm. 5. Dimension D and E1 to be determined at Datum Plane H. Package Drawing Contact: packagedrawings@atmel.com H 8X E 12/8/11 8X, 8-lead 4.4mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) TNR C

17AT24HC04B [DATASHEET] Atmel-5227F-SEEPROM-AT24HC04B-Datasheet_022014 13. Revision History Doc. Rev. Date Comments 5227F 02/2014 Update Atmel template (no changes to functional specfication). logos, and disclaimer page, part markings to a single page, and package drawings 8P3, 8S1, and 8A2 to 8X. Update the Random Read figure and add the AC measurement conditions note to the AC Characteristics table. 5227E 11/2008 Update pin configurations. 5227D 01/2008 Remove ‘preliminary’ status. 5227C 08/2007 Adde Part Marking Scheme. 5227B 08/2007 Update to new template and common figures. Adde Part Marking tables. 5227A 04/2007 Initial document release.

Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 | www.atmel.com © 2014 Atmel Corporation. / Rev.: Atmel-5227F-SEEPROM-AT24HC04B-Datasheet_022014. Atmel®, Atmel logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDIT IONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS P RODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMI TATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or c ompleteness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel d oes not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automo tive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical A pplications”) without an Atmel officer's specific written consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for t he operation of nuclear facilities and weapons systems. Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.