AT24HC02B_0701 ATMEL
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 16
Technical content
Features
- Write Protect Pin for Hardware Data Protection – Utilizes Different Array Protection Compared to the AT24C02B
- Medium-voltage and Standard-voltage Operation – 2.5 (V CC = 2.5V to 5.5V)
- Automotive Temperature Range –40°C to 125°C
- Internally Organized 256 x 8 (2K)
- Two-wire Serial Interface
- Schmitt Trigger, Filtered Inputs for Noise Suppression
- Bidirectional Data Transfer Protocol
- 400 kHz (2.5V) Compatibility
- Write Protect Pin for Hardware Data Protection
- 8-byte Page Write Modes
- Partial Page Writes are Allowed
- Self-timed Write Cycle (5 ms max)
- High-reliability – Endurance: 1 Million Write Cycles – Data Retention: 100 Years
- 8-lead JEDEC SOIC and 8-lead TSSOP Packages
Description
The AT24HC02B provides 2048 bits of serial electrically erasable and programmable read-only memory (EEPROM) organized as 256 words of 8 bits each. The device is optimized for use in many automotive applications where low-power and low-voltage operation are essential. The AT24HC02B is available in space-saving 8-lead JEDEC SOIC and 8-lead TSSOP packages and is acce ssed via a two-wire serial interface. In addition, the entire family is available in 2.5V (2.5V to 5.5V) versions. Table 1. Pin Configurations
2 AT24HC02B [Preliminary]
Figure 1. Block Diagram EEPROM device and negative edge clock data out of each device. under the Device Addressing section).
protection feature is enabled and operates as shown in the following table. each, the 2K requires an 8-bit data word address for random word addressing. Table 2. Write Protect
4 AT24HC02B [Preliminary]
Note: 1. This parameter is characterized and is not 100% tested. Note: 1. V IL min and VIH max are reference only and are not tested. Table 3. Pin Capacitance(1) Table 4. DC Characteristics
Notes: 1. This parameter is characterized and is not 100% tested (T A = 25°C).
- This parameter is characterized.
which must precede any other command (see to Figure 6 on page 7). STOP CONDITION: A low-to-high transition of SDA wit h SCL high is a stop condition. mode (see Figure 6 on page 7). received each word. This happens during the ninth clock cycle. Table 5. AC Characteristics
6 AT24HC02B [Preliminary]
Figure 2. Software Reset Protocol Figure 3. SCL: Serial Clock, SDA: Serial Data I/O
8 AT24HC02B [Preliminary]
Figure 7. Output Acknowledge
AT24HC02B [Preliminary] 5192A–SEEPR–1/07 Device Addressing The 2K EEPROM device requires an 8-bit dev ice address word following a start condi- tion to enable the chip for a read or write operation (see to Figure 8 on page 10). The device address word consists of a mandatory “1”, “0” sequence for the first four most significant bits as shown. This is common to all the Serial EEPROM devices. The next 3 bits are the A2, A1 and A0 device address bits for the 2K EEPROM. These 3 bits must compare to their corresponding hardwired input pins. The eighth bit of the device address is the r ead/write operation select bit. A read opera- tion is initiated if this bit is high and a write operation is initiated if this bit is low. Upon a compare of the device address, th e EEPROM will output a “0”. If a compare is not made, the chip will return to a standby state. Write Operations BYTE WRITE: A write operation requires an 8-bit data word address following the device address word and acknowledgment. Upon receipt of this address, the EEPROM will again respond with a “0” and then clock in the first 8-bit data word. Following receipt of the 8-bit data word, the EEPROM will output a “0” and the addressing device, such as a microcontroller, must terminate the writ e sequence with a stop condition. At this time the EEPROM enters an internally timed write cycle, t WR, to the nonvolatile memory. All inputs are disabled during this write cycle and the EEPROM will not respond until the write is complete (see Figure 9 on page 10). PAGE WRITE: The 2K EEPROM is capable of an 8-byte page write. A page write is initiated the same as a byte write, but the microcontroller does not send a stop condition after the fi rst data word is clocked in. Instead, after the EEPROM acknowledges receipt of the first data word, the microcontroller can transmit up to seven data words. The EEPROM will respond with a “0 ” after each data word received. The microcontroller must terminate the page writ e sequence with a stop condition (see Fig- ure 10 on page 11). The data word address lower three bits are in ternally incremented following the receipt of each data word. The higher data word address bits are not incremented, retaining the memory page row location. When the word address, internally generated, reaches the page boundary, the following byte is placed at the beginning of the same page. If more than eight data words are transmitted to the EEPROM, the data word address will “roll over” and previous data will be overwritten. ACKNOWLEDGE POLLING: Once the internally timed write cycle has started and the EEPROM inputs are disabled, acknowledge polling can be initiated. This involves send- ing a start condition followed by the dev ice address word. The read/write bit is representative of the operation desired. Only if the internal write cycle has completed will the EEPROM respond with a “0”, allowing the read or write sequence to continue. Read Operations Read operations are initiated the same way as write operations with the exception that the read/write select bit in the device address word is set to “1”. There are three read operations: current address read, random address read and sequential read. CURRENT ADDRESS READ: The internal data word address counter maintains the last address accessed during the last read or write operation, incremented by one. This address stays valid between operations as long as the chip power is maintained. The address “roll over” during read is from the last byte of the last memory page to the first byte of the first page. The address “roll over” during write is from the last byte of the cur- rent page to the first byte of the same page.
10 AT24HC02B [Preliminary]
acknowledged by the EEPROM, the microcontr oller must generate another start condition. ing stop condition (see Figure 11 on page 11). with a “0” but does generate a following stop condition (see Figure 13 on page 12). Figure 8. Device Address Figure 9. Byte Write
12 AT24HC02B [Preliminary]
5192A–SEEPR–1/07 Notes: 1. “-B” denotes bulk. 2. “-T” denotes tape and reel. SOIC = 4K per reel. TSSOP = 5K per reel. Ordering Code Package Operation Range AT24HC02BN-SP25-B(1) AT24HC02BN-SP25-T(2) AT24HC02B-TP25-B(1) AT24HC02B-TP25-T(2) 8S1 8S1 8A2 8A2 Lead-free/Halogen-free/NiPdAu Lead Finish/Automotive Temperature (−40°C to 125°C) Package Type 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) Options −2.5 Low-voltage (2.5V to 5.5V)
AT24HC02B [Preliminary] 5192A–SEEPR–1/07 Packaging Information 8S1 – JEDEC SOIC 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. Note: 10/7/03 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) 8S1 B COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. A 1.35 – 1.75 b 0.31 – 0.51 C 0.17 – 0.25 D 4.80 – 5.00 E1 3.81 – 3.99 E 5.79 – 6.20 e 1.27 BSC L 0.40 – 1.27 ∅ 0˚ – 8˚ Top View End View Side View e B D A N E C L
14 AT24HC02B [Preliminary]
5192A–SEEPR–1/07
2325 Orchard Parkway
San Jose, CA 95131 TITLE DRAWING NO. R REV. 5/30/02 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 2.90 3.00 3.10 2, 5 E 6.40 BSC E1 4.30 4.40 4.50 3, 5 A – – 1.20 A2 0.80 1.00 1.05 b 0.19 – 0.30 4 e 0.65 BSC L 0.45 0.60 0.75 L1 1.00 REF 8A2, 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimension D and E1 to be determined at Datum Plane H. 8A2 B Side View End ViewTop View A L D 123 N b Pin 1 indicator this corner E e 8A2 – TSSOP
AT24HC02B [Preliminary] 5192A–SEEPR–1/07
Revision History
Doc. Rev. Date Comments 5192A 1/2007 Initial document release.
Printed on recycled paper. 5192A–SEEPR–1/07 Disclaimer: The information in this document is provided in connection with Atmel products. No license, expr ess or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LI ABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTOR Y WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO , THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICU LAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR I NCIDEN- TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTE RRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or comp leteness of the contents of th is document and reserves the rig ht to make changes to specifications and product descriptions at any time withou t notice. Atmel does not make any commitm ent to update the information contained her ein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not int ended, authorized, or warranted for use as components in applications intended to support or sustain life. Atmel Corporation Atmel Operations San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza
77 Mody Road Tsimshatsui
Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Memory San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 Microcontrollers San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602
44306 Nantes Cedex 3, France
13106 Rousset Cedex, France
1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 RF/Automotive Theresienstrasse 2 Postfach 3535
74025 Heilbronn, Germany
1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123
38521 Saint-Egreve Cedex, France
www.atmel.com/literature © 2007 Atmel Corporation. All rights reserved. Atmel ®, logo and combinations thereof, Everywhere You Are ® and others, are registered trade- marks or trademarks of Atmel Corporation or its subsidia ries. Other terms and product names may be trademarks of others.