DATASHEET SEARCH SITE
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 19
Technical content
- Features Write Protect Pin for Hardware Data Protection – Utilizes Different Array Protection Compared to the AT24C02B Low-voltage and Standard-voltage Operation –1 . 8 ( VCC =1 . 8 Vt o5 . 5 V ) Internally Organized 256 x 8 (2K) Two-wire Serial Interface Schmitt Trigger, Filtered Inputs for Noise Suppression Bidirectional Data Transfer Protocol 1 MHz (5V) and 400 kHz (1.8V, 2.5V, 2.7V) Clock Rate 8-byte Page Partial Page Writes Allowed Self-timed Write Cycle (5 ms Max) High Reliability – Endurance: One Million Write Cycles – Data Retention: 100 Years 8-lead PDIP, 8-lead JEDEC SOIC and 8-lead TSSOP Packages Die Sales: Wafer Form, Tape and Reel, and Bumped Wafers 2. Description The AT24HC02B provides 2048 bits of serial electrically erasable and programmable read-only memory (EEPROM) organized as 256 words of 8 bits each. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. The AT24HC02B is available in space-saving 8-lead PDIP, 8-lead JEDEC SOIC and 8-lead TSSOP packages and is accessed via a two-wire serial interface. In addition, the entire family is available in 1.8V (1.8V to 5.5V) version. Table 2-1. Pin Configuration Pin Name Function A0–A2 Address Inputs SDA Serial Data SCL Serial Clock Input WP Write Protect Two-wire Serial EEPROM 2K (256 x 8) AT24HC02B Not Recommended for New Design. Replaced by AT24HC02C. Rev. 5134E–SEEPR–3/08 GND VCC WP SCL SDA 8-lead PDIP GND VCC WP SCL SDA 8-lead SOIC GND VCC WP SCL SDA 8-lead TSSOP
5134E–SEEPR–3/08 AT24HC02B Figure 2-1. Block Diagram Absolute Maximum Ratings* Maximum Ratings” may cause permanent dam- age to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Voltage on Any Pin START STOP LOGIC VCC GND WP SCL SDA SERIAL CONTROL LOGIC EN H.V. PUMP/TIMING EEPROM DATA RECOVERY SERIAL MUX X DEC DOUT/ACK LOGIC COMP LOAD INC DATA WORD ADDR/COUNTER Y DEC R/W DOUT DIN LOAD DEVICE ADDRESS COMPARATOR
5134E–SEEPR–3/08 AT24HC02B 3. Pin Description SERIAL CLOCK (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative edge clock data out of each device. SERIAL DATA (SDA): The SDA pin is bidirectional for serial data transfer. This pin is open- drain driven and may be wire-ORed with any number of other open-drain or open collector devices. DEVICE/PAGE ADDRESSES (A2, A1, A0): The A2, A1 and A0 pins are device address inputs that must be hardwired for the AT24HC02B. As many as eight 2K devices may be addressed on a single bus system. (Device addressing is discussed in detail under Device Addressing, page 8). WRITE PROTECT (WP): The AT24HC02B has a WP pin that provides hardware data protec- tion. The WP pin allows normal read/write operations when connected to ground (GND). When the WP pin is connected to V CC, the write protection feature is enabled and operates as shown. Table 3-1. Write Protect WP Pin Status Part of the Array Protected 24HC02B At VCC Upper Half (1K) Array At GND Normal Read/Write Operations
5134E–SEEPR–3/08 AT24HC02B 4. Memory Organization AT24HC02B, 2K SERIAL EEPROM: The 2K is internally organized with 32 pages of 8 bytes each. Random word addressing requires an 8-bit data word address. Note: 1. This parameter is characterized and is not 100% tested. Note: 1. V IL min and VIH max are reference only and are not tested. Table 4-1. Pin Capacitance(1) Applicable over recommended operating range from TAI =2 5C ,f=1 . 0M H z ,VCC = +1.8V Symbol Test Condition Max Units Conditions CI/O Input/Output Capacitance (SDA) 8 pF V I/O =0 V CIN Input Capacitance (A0,A 1,A 2, SCL) 6 pF V IN =0 V Table 4-2. DC Characteristics Applicable over recommended operating range from: TAI = 40C to +85C, VCC = +1.8V to +5.5V (unless otherwise noted) Symbol Parameter Test Condition Min Typ Max Units VCC1 Supply Voltage 1.8 5.5 V VCC2 Supply Voltage 2.5 5.5 V VCC3 Supply Voltage 2.7 5.5 V VCC4 Supply Voltage 4.5 5.5 V ICC Supply Current VCC = 5.0V READ at 100 kHz 0.4 1.0 mA ICC Supply Current VCC = 5.0V WRITE at 100 kHz 2.0 3.0 mA ISB1 Standby Current VCC =1 . 8 V V IN =V CC or VSS 0.6 3.0 µA ISB2 Standby Current VCC =2 . 5 V V IN =V CC or VSS 1.4 4.0 µA ISB3 Standby Current VCC =2 . 7 V V IN =V CC or VSS 1.6 4.0 µA ISB4 Standby Current VCC =5 . 0 V V IN =V CC or VSS 8.0 18.0 µA ILI Input Leakage Current V IN =V CC or VSS 0.10 3.0 µA ILO Output Leakage Current V OUT =V CC or VSS 0.05 3.0 µA VIL Input Low Level (1) 0.6 V CC x 0.3 V VIH Input High Level (1) VCC x 0.7 V CC + 0.5 V VOL2 Output Low Level VCC =3 . 0 V I OL = 2.1 mA 0.4 V VOL1 Output Low Level VCC =1 . 8 V I OL = 0.15 mA 0.2 V
5134E–SEEPR–3/08 AT24HC02B Note: 1. This parameter is ensured by characterization only. Table 4-3. AC Characteristics Applicable over recommended operating range from T AI = –40Ct o+ 8 5C, VCC = +1.8V to +5.5V, CL = 1 TTL Gate and 100 pF (unless otherwise noted) Symbol Parameter UnitsMin Max Min Max fSCL Clock Frequency, SCL 400 1000 kHz tLOW Clock Pulse Width Low 1.2 0.4 µs tHIGH Clock Pulse Width High 0.6 0.4 µs tI Noise Suppression Time 50 40 ns tAA Clock Low to Data Out Valid 0.1 0.9 0.05 0.55 µs tBUF Time the bus must be free before a new transmission can start 1.2 0.5 µs tHD.STA Start Hold Time 0.6 0.25 µs tSU.STA Start Setup Time 0.6 0.25 µs tHD.DAT Data In Hold Time 0 0 µs tSU.DAT Data In Setup Time 100 100 ns tR Inputs Rise Time(1) 0.3 0.3 µs tF Inputs Fall Time(1) 300 100 ns tSU.STO Stop Setup Time 0.6 .25 µs tDH Data Out Hold Time 50 50 ns tWR Write Cycle Time 5 5 ms Endurance(1) 5.0V, 25C, Byte Mode 1 Million Write Cycles
5134E–SEEPR–3/08 AT24HC02B Figure 5-6. Output Acknowledge 6. Device Addressing The 2K EEPROM device requires an 8-bit device address word following a start condition to enable the chip for a read or write operation, as shown in Figure 6-1. Figure 6-1. Device Address The device address word consists of a mandatory “1”, “0” sequence for the first four most signif- icant bits as shown. This is common to all the EEPROM devices. The next three bits are the A2, A1 and A0 device address bits for the 2K EEPROM. These three bits must compare to their corresponding hardwired input pins. The eighth bit of the device address is the read/write operation select bit. A read operation is ini- tiated if this bit is high, and a write operation is initiated if this bit is low. Upon a compare of the device address, the EEPROM will output a “0”. If a compare is not made, the chip will return to a standby state. SCL DATA IN DATA OUT START ACKNOWLEDGE 981 MSB LSB
1 A2 A0A1 R/W00 1
5134E–SEEPR–3/08 AT24HC02B SEQUENTIAL READ: Sequential reads are initiated by either a current address read or a ran- dom address read. After the microcontroller receives a data word, it responds with an acknowledge. As long as the EEPROM receives an acknowledge, it will continue to increment the data word address and serially clock out sequential data words. When the memory address limit is reached, the data word address will “roll over” and the sequential read will continue. The sequential read operation is terminated when the microcontroller does not respond with a “0” but does generate a following stop condition, see Figure 8-3. Figure 8-3. Sequential Read
5134E–SEEPR–3/08 AT24HC02B Notes: 1. “-B” denotes bulk. 2. “-T” denotes tape and reel. SOIC = 4K per reel. TSSOP = 5K per reel. 3. Available in tape and reel and wafer form; order as SL788 for inkless wafer form. Bumped die available upon request. Please contact Serial Interface Marketing. 9. AT24HC02B Ordering Information Ordering Code Voltage Package Operation Range AT24HC02B-PU (Bulk form only) 1.8 8P3 Lead-free/Halogen-free/ Industrial Temperature (40Ct o8 5C) AT24HC02BN-SH-B(1) (NiPdAu Lead Finish) 1.8 8S1 AT24HC02BN-SH-T(2) (NiPdAu Lead Finish) 1.8 8S1 AT24HC02B-TH-B(1) (NiPdAu Lead Finish) 1.8 8A2 AT24HC02B-TH-T(2) (NiPdAu Lead Finish) 1.8 8A2 AT24HC02B-W-11(3) 1.8 Die Sale Industrial Temperature (40Ct o8 5C) Package Type 8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Options 1.8 Low Voltage (1.8V to 5.5V)
5134E–SEEPR–3/08 AT24HC02B 10. Part marking scheme 10.1 8-PDIP 10.2 8-SOIC TOP MARK Seal Year Y = SEAL YEAR WW = SEAL WEEK | Seal Week 6: 2006 0: 2010 02 = Week 2 | | | 7: 2007 1: 2011 04 = Week 4 A T M L H Y W W 9: 2009 3: 2013 :: : :::: :: H 2 B 1 52 = Week 52 * Lot Number Lot Number to Use ALL Characters in Marking | BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark TOP MARK Seal Year Y = SEAL YEAR WW = SEAL WEEK | Seal Week 6: 2006 0: 2010 02 = Week 2 | | | 7: 2007 1: 2011 04 = Week 4 A T M L H Y W W 9: 2009 3: 2013 :: : :::: :: H 2 B 1 52 = Week 52 * Lot Number Lot Number to Use ALL Characters in Marking | BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark
5134E–SEEPR–3/08 AT24HC02B 10.3 8-TSSOP TOP MARK Pin 1 Indicator (Dot) Y = SEAL YEAR WW = SEAL WEEK | 6: 2006 0: 2010 02 = Week 2 H 2 B 1 50 = Week 50 BOTTOM MARK P H A A A A A A A <- Pin 1 Indicator
5134E–SEEPR–3/08 AT24HC02B 11. Packaging Information 11.1 8P3 – PDIP
2325 Orchard Parkway
San Jose, CA 95131 TITLE DRAWING NO. R REV. 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) 01/09/02 8P3 B Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA, for additional information . 2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion. COMMON DIMENSIONS (Unit of Measure = inches) SYMBOL MIN NOM MAX NOTE D E e Lb2 b A2 A N eA c
4 PLCS
A – – 0.210 2 A2 0.115 0.130 0.195 b 0.014 0.018 0.022 5 b2 0.045 0.060 0.070 6 b3 0.030 0.039 0.045 6 c 0.008 0.010 0.014 D 0.355 0.365 0.400 3 D1 0.005 – – 3 E 0.300 0.310 0.325 4 E1 0.240 0.250 0.280 3 e 0.100 BSC eA 0.300 BSC 4 L 0.115 0.130 0.150 2 Top View Side View End View
5134E–SEEPR–3/08 AT24HC02B 11.2 8S1 – JEDEC SOIC 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. Note: 10/7/03 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) 8S1 B COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. A 1.35 – 1.75 b 0.31 – 0.51 C 0.17 – 0.25 D 4.80 – 5.00 E1 3.81 – 3.99 E 5.79 – 6.20 e 1.27 BSC L 0.40 – 1.27 ∅ 0° – 8° Top View End View Side View e B D A N E C L
5134E–SEEPR–3/08 AT24HC02B 11.3 8A2 – TSSOP San Jose, CA 95131 TITLE DRAWING NO. R REV. 5/30/02 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 2.90 3.00 3.10 2, 5 E 6.40 BSC E1 4.30 4.40 4.50 3, 5 A – – 1.20 A2 0.80 1.00 1.05 b 0.19 – 0.30 4 e 0.65 BSC L 0.45 0.60 0.75 L1 1.00 REF 8A2, 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimension D and E1 to be determined at Datum Plane H. 8A2 B Side View End ViewTop View A L D 123 N b Pin 1 indicator this corner E e
5134E–SEEPR–3/08 AT24HC02B 12. Revision History Doc. Rev. Date Comments 5134E 9/2013 NRND. Replaced by AT24HC02B 5134E 3/2008 Added part marking scheme Updated to new template 5134D 4/2007 Removed reference to Waffle Pack on page 1 Added lines to Ordering Code table Shrink Pin Diagram; Change to Table 5; Added Two-Wire Software Reset; Removed LSB from figures 5134C 3/2007 Pg. 12 - Change to new catalog part number scheme. 5134B 9/2006 Revision history implemented; Added ‘Preliminary’ status to datasheet.
5134E–SEEPR–3/08 Headquarters International Atmel Corporation San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Room 1219 Chinachem Golden Plaza
77 Mody Road Tsimshatsui
Tel: (852) 2721-9778 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309
78054 Saint-Quentin-en-
9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Product Contact Web Site www.atmel.com Technical Support s_eeprom@atmel.com Sales Contact www.atmel.com/contacts Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN- TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to s pecifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifica lly provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2008 Atmel Corporation . All rights reserved. Atmel ®, logo and combinations thereof, and others, are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.