DATASHEET SEARCH SITE
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 24
Technical content
Atmel-8766D-SEEPROM-AT24CS04-08-Datasheet_072013 Standard Features Low-voltage operation VCC = 1.7V to 5.5V Internally organized as 512 x 8 (4-Kbit) or 1024 x 8 (8-Kbit) I2C-compatible (2-wire) serial interface Schmitt Trigger, filtered inputs for noise suppression Bidirectional data transfer protocol 400kHz (1.7V) and 1MHz (2.5V, 2.7, 5.0V) compatibility Write Protect pin for hardware data protection 16-byte page write mode Partial page writes allowed Self-timed write cycle (5ms max) High-reliability Endurance: 1,000,000 write cycles Data retention: 100 years Green package options (Pb/Halide-free/RoHS-compliant) 8-lead JEDEC SOIC, 8-lead TSSOP, 8-pad UDFN, and 5-lead SOT23 Die sale options: wafer form and tape and reel available Enhanced Features in the CS Serial EEPROM Series All standard features supported 128-bit unique factory-programmed serial number Permanently locked, read-only value Stored in a separate memory area Guaranteed unique across entire CS Series of Serial EEPROMs AT24CS04 and AT24CS08 I2C-Compatible (2-wire) Serial EEPROM with a Unique, Factory Programmed 128-bit Serial Number 4-Kbit (512 x 8), 8-Kbit (1024 x 8) DATASHEET
AT24CS04/08 [DATASHEET] Atmel-8766D-SEEPROM-AT24CS04-08-Datasheet_072013 1. Description The Atmel® AT24CS04 and AT24CS08 provides 4096/8192 bits of Serial Electrically Erasable and Programmable Read-only Memory (EEPROM) organized as 512/1024 words of eight bits each. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. The AT24CS04/08 is available in space-saving, 8-lead JEDEC SOIC, 8-lead TSSOP, 8-pad UDFN and 5-lead SOT23 packages and is accessed via a 2-wire serial interface. In addition, both devices fully operate from 1.7V to 5.5V V CC. The AT24CS04/08 provides the additional feature of a factory programmed, guaranteed unique 128-bit serial number, while maintaining all of the traditional features available in the 4-Kbit or 8-Kbit Serial EEPROM. The time consuming step of performing and ensuring true serialization of product on a manufacturing line can be removed from the production flow by employing the CS Series Serial EEPROM. The 128-bit serial number is programmed and permanently locked from future writing during the Atmel production process. Further, this 128-bit location does not consume any of the user read/write area of the 4-Kbit or 8-Kbit Serial EEPROM. The uniqueness of the serial number is guaranteed across the entire CS Series of Serial EEPROMs, regardless of the size of the memory array or the type of interface protocol. This means that as an application's needs for memory size or interface protocol evolve in future generations, any previously deployed serial number from any Atmel CS Series Serial EEPROM part will remain valid. 2. Pin Descriptions and Pinout Figure 2-1. Pin Configuration Note: For use of 5-lead SOT23, the software A2, A1, and A0 bits in the device address word must be set to zero to properly communicate with the device. Pin Name Function NC No Connect A1 Address Input (4K only) A2 Address Input SDA Serial Data SCL Serial Clock Input WP Write Protect GND Ground VCC Power Supply NC A 1/NC GND VCC WP SCL SDA 8-lead SOIC SCL GND SDA WP V CC 5-lead SOT23 V CC WP SCL SDA NC A1/NC GND 8-pad UDFN Bottom View NC A1/NC GND VCC WP SCL SDA 8-lead TSSOP
3AT24CS04/08 [DATASHEET] Atmel-8766D-SEEPROM-AT24CS04-08-Datasheet_072013 3. Absolute Maximum Ratings 4. Block Diagram Figure 4-1. Block Diagram Voltage on any pin *Notice: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Start Stop Logic Data Word ADDR/Counter Row Decoder Device Address Comparator Data Latches DOUT / ACK Logic Column Decoder EEPROM Array Serial Control Logic High Voltage Pump & Timing 128-bit Serial Number Serial MUX Read Read/Write Enable COMP Load INC VCC GND WP SCL SDA DOUT DIN
AT24CS04/08 [DATASHEET] Atmel-8766D-SEEPROM-AT24CS04-08-Datasheet_072013 5. Pin Description Serial Clock (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative edge clock data out of each device. Serial Data (SDA): The SDA pin is bidirectional for serial data transfer. This pin is open-drain driven and may be wire-ORed with any number of other open-drain or open-collector devices. Device Addresses (A2, A1): The AT24CS04 uses the A2 and A1 inputs for hard wire addressing allowing a total of four 4-Kbit devices to be addressed on a single bus system. Pin 1 is a no connect and can be connected to ground. The AT24CS08 only uses the A2 input for hardware addressing and a total of two 8K devices may be addressed on a single bus system. Pins 1 and 2 are no connects and can be connected to ground. Refer to Section 8. “Device Addressing” on page 10 for details about the pin state and the required protocol for communication . The device address pins are not available on the SOT23 package offering. Refer to Section 8. “Device Addressing” on page 10 for details on the protocol requirements with this package. Write Protect (WP): AT24CS04/08 has a Write Protect (WP) pin that provides hardware data protection. When the Write Protect pin is connected to ground (GND), normal read/write operations to the full array are possible. When the Write Protect pin is connected to V CC, all write operations to the memory are inhibited but read operations are still possible. This operation is summarized in Table 5-1 below. Table 5-1. Write Protect WP Pin Status Part of the Array Protected Atmel AT24CS04/08 At VCC Full Array At GND Normal Read/Write Operations
5AT24CS04/08 [DATASHEET] Atmel-8766D-SEEPROM-AT24CS04-08-Datasheet_072013 6. Memory Organization Atmel AT24CS04, 4K Serial EEPROM: Internally organized with 32 pages of 16 bytes each, the 4-Kbit device requires a 9-bit data word address for random word addressing. Atmel AT24CS08, 8K Serial EEPROM: Internally organized with 64 pages of 16 bytes each, the 8-Kbit device requires a 10-bit data word address for random word addressing. Table 6-1. Pin Capacitance (1) Note: 1. This parameter is characterized and is not 100% tested. Table 6-2. DC Characteristics Note: 1. V IL min and VIH max are reference only and are not tested. Applicable over recommended operating range from TA = 25°C, f = 1.0MHz, VCC = 1.7V to 5.5V Symbol Test Condition Max Units Conditions CI/O Input/Output Capacitance (SDA) 8 pF VI/O = 0V CIN Input Capacitance (A1, A2, SCL) 6 pF VIN = 0V Applicable over recommended operating range from: TAI = -40C to +85C, VCC = 1.7V to 5.5V (unless otherwise noted) Symbol Parameter Test Condition Min Typ Max Units VCC Supply Voltage 1.7 5.5 V ICC1 Supply Current VCC = 5.0V Read at 400kHz 0.4 1.0 mA ICC2 Supply Current VCC = 5.0V Write at 400kHz 2.0 3.0 mA ISB1 Standby Current VCC = 1.7V VIN = VCC or VSS 1.0 μA ISB2 Standby Current VCC = 5.5V VIN = VCC or VSS 6.0 μA ILI Input Leakage Current VIN = VCC or VSS 0.10 3.0 μA ILO Output Leakage Current VOUT = VCC or VSS 0.05 3.0 μA VIL Input Low Level(1) –0.6 VCC x 0.3 V VIH Input High Level(1) VCC x 0.7 VCC + 0.5 V VOL1 Output Low Level VCC = 1.7V IOL = 0.15mA 0.2 V VOL2 Output Low Level VCC = 3.0V IOL = 2.1mA 0.4 V
AT24CS04/08 [DATASHEET] Atmel-8766D-SEEPROM-AT24CS04-08-Datasheet_072013 Table 6-3. AC Characteristics Note: 1. This parameter is ensured by characterization only. Applicable over recommended operating range from TAI = –40C to +85C, VCC = 1.7V to 5.5V, CL = 1TTL Gate and 100pF (unless otherwise noted) Symbol Parameter 1.7V 2.5V, 5.0V UnitsMin Max Min Max fSCL Clock Frequency, SCL 400 1000 kHz tLOW Clock Pulse Width Low 1.2 0.4 μs tHIGH Clock Pulse Width High 0.6 0.4 μs tI Noise Suppression Time 100 50 ns tAA Clock Low to Data Out Valid 0.1 0.9 0.05 0.55 μs tBUF Time the bus must be free before a new transmission can start 1.3 0.5 μs tHD.STA Start Hold Time 0.6 0.25 μs tSU.STA Start Setup Time 0.6 0.25 μs tHD.DAT Data In Hold Time 0 0 μs tSU.DAT Data In Setup Time 100 100 ns tR Inputs Rise Time(1) 0.3 0.3 μs tF Inputs Fall Time(1) 300 100 ns tSU.STO Stop Setup Time 0.6 0.25 μs tDH Data Out Hold Time 50 50 ns tWR Write Cycle Time 5 5 ms Endurance(1) 25C, Page Mode, 3.3V 1,000,000 Write Cycles
7AT24CS04/08 [DATASHEET] Atmel-8766D-SEEPROM-AT24CS04-08-Datasheet_072013 7. Device Operation Clock and Data Transitions: The SDA pin is normally pulled high with an external device. Data on the SDA pin may change only during SCL low time periods (see Figure 7-4 on page 9). Data changes during SCL high periods will indicate a Start or Stop condition as defined below. Start Condition: A high-to-low transition of SDA with SCL high is a Start condition which must precede any other command (see Figure 7-5 on page 9). Stop Condition: A low-to-high transition of SDA with SCL high is a Stop condition. After a read sequence, the Stop command will place the EEPROM in a standby power mode (see Figure 7-5 on page 9). Acknowledge: All addresses and data words are serially transmitted to and from the EEPROM in 8-bit words. The EEPROM sends a zero to acknowledge that it has received each word. This happens during the ninth clock cycle. Standby Mode: The AT24CS04/08 features a low-power standby mode which is enabled upon power-up as well as after the receipt of the Stop bit and the completion of any internal operations. 2-wire Software Reset: After an interruption in protocol, power loss, or system reset, any 2-wire part can be reset by following these steps: 1. Create a start bit condition. 2. Clock nine cycles. 3. Create another start bit followed by stop bit condition as shown in Figure 7-1. The device is ready for next communication after above steps have been completed. Figure 7-1. Software reset SCL 9 Start Bit Start Bit Stop Bit 8321 SDA Dummy Clock Cycles
AT24CS04/08 [DATASHEET] Atmel-8766D-SEEPROM-AT24CS04-08-Datasheet_072013 8. Device Addressing Standard EEPROM Access: The 4-Kbit and 8-Kbit EEPROM device requires an 8-bit device address word following a Start condition to enable the chip for a read or write operation. The device address word consists of a mandatory ‘1010’ (Ah) sequence for the first four most significant bits as shown in Figure 8-1 below. This is common to all Serial EEPROM devices. The 4K EEPROM only uses the A2 and A1 device address bits with the third bit being a memory page address bit (P0). The two device address bits must compare to their corresponding hard-wired input pins. Pin 1 is a no connect. The 8K EEPROM only uses the A2 device address bit with the next two bits being for memory page addressing (P1, P0). The A2 must compare to its corresponding hard-wired A 2 input pin. Pins 1 and 2 are not connected. The eighth bit of the device address is the read/write operation select bit. A read operation is initiated if this bit is high and a write operation is initiated if this bit is low. Upon a compare of the device address, the EEPROM will output a zero. If a compare is not made, the chip will return to a standby state. Note: For the SOT23 package offering, the 4-Kbit EEPROM software A2 and A1 bits in the device address word must be set to zero to properly communicate. The 8-Kbit EEPROM software A2 bit in the device address word must be set to zero to properly communicate in the SOT23 paclkage. Serial Number Access: The AT24CS04 and AT24CS08 utilizes a separate memory block containing a factory programmed 128-bit serial number. Access to this memory location is obtained by beginning the device address word with a ‘1011’ (Bh) sequence. The behavior of the next three bits remain the same as during a standard EEPROM addressing sequence. These three bits must compare to their corresponding hard-wired input pins A 2 and A1 (4-Kbit only) in order for the part to acknowledge. The restrictions for these bits with a SOT23 package are the same when accessing the serial number feature. The eighth bit of the device address needs be set to a one to read the Serial Number. A zero in this bit position, other than during a dummy write sequence to set the address pointer, will result in a unknown data read from the part. Writing or altering the 128-bit serial number is not possible. Further specific protocol is needed to read the serial number from of the device. See Read Operations on page 11 for more details on accessing the special feature. Table 8-1. Device Address Density Access Area Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 4-Kbit EEPROM 1 0 1 0 A2 A1 P0 R/W Serial Number 1 0 1 1 A2 A1 0 1 8-Kbit EEPROM 1 0 1 0 A2 P1 P0 R/W Serial Number 1 0 1 1 A2 0 0 1 MSB LSB
11AT24CS04/08 [DATASHEET] Atmel-8766D-SEEPROM-AT24CS04-08-Datasheet_072013 9. Write Operations Byte Write: A Byte Write operation requires an 8-bit word address following the device address word and acknowledgment. Upon receipt of this address, the EEPROM will again respond with a zero and then clock in the first 8-bit data word. Following receipt of the 8-bit data word, the EEPROM will output a zero and the addressing device, such as a microcontroller, must terminate the write sequence with a Stop condition. At this time the EEPROM enters an internally timed write cycle, t WR, to the nonvolatile memory. All inputs are disabled during this write cycle and the EEPROM will not respond until the Write is complete (see Figure 10-1 on page 12). Page Write: The 4-Kbit and 8-Kbit devices are capable of 16-byte Page Writes. A Page Write is initiated in the same way as a Byte Write, but the microcontroller does not send a Stop condition after the first data word is clocked in. Instead, after the EEPROM acknowledges receipt of the first data word, the microcontroller can transmit up to fifteen additional data words. The EEPROM will respond with a zero after each data word received. The microcontroller must terminate the Page Write sequence with a Stop condition (see Figure 10-2 on page 12). The data word address lower four bits are internally incremented following the receipt of each data word. The higher data word address bits are not incremented, retaining the memory page row location. When the internally generated word address reaches the page boundary, the subsequent byte loaded will be placed at the beginning of the same page. If more than sixteen data words are transmitted to the EEPROM, the data word address will roll-over and previously loaded data will be overwritten. Acknowledge Polling: Once the internally timed write cycle has started and the EEPROM inputs are disabled, acknowledge polling can be initiated. This involves sending a Start condition followed by the device address word. The Read/Write bit is representative of the operation desired. Only if the internal write cycle has completed will the EEPROM respond with a zero allowing the next read or write sequence to begin. 10. Read Operations Read operations are initiated in the same way as Write operations with the exception that the Read/Write select bit in the device address word is set to one. There are four types of read operations: Current Address Read Random Address Read Sequential Read Serial Number Read Current Address Read: The internal data word address counter maintains the last address accessed during the last Read or Write operation, incremented by one. This address stays valid between operations as long as the chip power is maintained. The address roll-over during read is from the last byte of the last memory page to the first byte of the first page. The address roll-over during write is from the last byte of the current page to the first byte of the same page. Once the device address with the read/write select bit set to one is clocked in and acknowledged by the EEPROM, the current address data word is serially clocked out. The microcontroller does not respond with an zero but does generate a following Stop condition (see Figure 10-3 on page 13). Random Read: A Random Read requires a dummy byte write sequence to load in the data word address. Once the device address word and data word address are clocked in and acknowledged by the EEPROM, the microcontroller must generate another Start condition. The microcontroller now initiates a Current Address Read by sending a device address with the read/write select bit high. The EEPROM acknowledges the device address and serially clocks out the data word. The microcontroller does not respond with a zero but does generate a following Stop condition (see Figure 10-4 on page 13). Sequential Read: Sequential reads are initiated by either a current address read or a random address read. After the microcontroller receives a data word, it responds with an acknowledge. As long as the EEPROM receives an acknowledge, it will continue to increment the data word address and serially clock out sequential data words. When the memory address limit is reached, the data word address will roll-over and the Sequential Read will continue. The Sequential Read operation is terminated when the microcontroller does not respond with a zero but does generate a following Stop condition (see Figure 10-5 on page 13).
AT24CS04/08 [DATASHEET] Atmel-8766D-SEEPROM-AT24CS04-08-Datasheet_072013 Figure 10-6. Serial Number Read Note: * This bit is A1 hardware address bit for the AT24CS04, and this bit is a zero for the AT24CS08. SDA LINE Device Address Word Address n Device Address S T A R T W R I T E S T A R T R E A D A C K A C K A C K A C K R W M S B Dummy Write Serial Number Data Byte 0x0 Serial Number Data Byte 0x1 Serial Number Data Byte 0x2 Serial Number Data Byte 0x3 Serial Number Data Byte 0xF N O A C K S T O P 1 0 1 1 1 0 0 0 0 0 0 0 1 0 1 1 * 0 1
15AT24CS04/08 [DATASHEET] Atmel-8766D-SEEPROM-AT24CS04-08-Datasheet_072013 11. Part Markings DRAWING NO. REV. TITLE Catalog Number Truncation AT24CS04 Truncation Code ##: N4 AT24CS08 Truncation Code ##: N8 AAAAAAAA## M @ATMLHYWW 8-lead SOIC 8-lead TSSOP AAAAAAA ## M @ ATHYWW 8-lead UDFN HM@ YXX 2.0 x 3.0 mm Body 5-lead SOT-23 ## MU YMXX Bottom Mark Top Mark Note 2: Package drawings are not to scale Note 1: designates pin 1 Package Mark Contact: DL-CSO-Assy_eng@atmel.com 24CS04-08SM A 5/7/12 24CS04-08SM, AT24CS04 and AT24CS08 Package Marking Information Date Codes Voltages Y = Year M = Month WW = Work Week of Assembly M: 1.7V min 2: 2012 6: 2016 A: January 02: Week 2 3: 2013 7: 2017 B: February 04: Week 4 5: 2015 9: 2019 L: December 52: Week 52 Country of Assembly Lot Number Grade/Lead Finish Material @ = Country of Assembly AAA...A = Atmel Wafer Lot Number H: Industrial/NiPdAu U: Industrial/Matte Tin Trace Code Atmel Truncation XX = Trace Code (Atmel Lot Numbers Correspond to Code) AT: Atmel Example: AA, AB.... YZ, ZZ ATM: Atmel ATML: Atmel AT24CS04 and AT24CS08: Package Marking Information
AT24CS04/08 [DATASHEET] Atmel-8766D-SEEPROM-AT24CS04-08-Datasheet_072013 12. Ordering Code Detail Atmel Designator Product Family Device Density Shipping Carrier Option Operating Voltage 04 = 4K 08 = 8K 24CS = Serial EEPROM, plus 128-bit serial number feature T = Tape and reel M = 1.7V to 5.5V Package Device Grade or Wafer/Die Thickness H = Green, NiPdAu lead finish, Industrial temperature range (-40˚C to +85˚C) U = Green, matte Sn lead finish, Industrial temperature range (-40˚C to +85˚C) 11 = 11mil wafer thickness Package Option SS = JEDEC SOIC X = TSSOP MA = UDFN ST = SOT23 WWU = Wafer unsawn AT24CS04-SSHM-T
17AT24CS04/08 [DATASHEET] Atmel-8766D-SEEPROM-AT24CS04-08-Datasheet_072013 13. Ordering Information
13.1 Atmel AT24CS04 Ordering Information
Additional package types that are not listed may be available. Please contact Atmel for more details. Notes: 1. Consistent with the general semiconductor market trend, Atmel will supply devices with either gold or cop- per bond wires to increase manufacturing flexibility and to ensure a long-term continuity of supply. There is no difference in product quality, reliability, or performance between the two variations. 2. T = Tape and reel SOIC = 4K units per reel TSSOP, UDFN, and SOT23 = 5K units per reel 3. For Wafer sales, please contact Atmel Sales. Atmel Ordering Code(1) Package Voltage Operation Range AT24CS04-SSHM-T(2) (NiPdAu Lead Finish) 8S1 1.7V to 5.5V Lead-free/Halogen-free/ Industrial Temperature (–40C to 85C) AT24CS04-XHM-T(2) (NiPdAu Lead Finish) 8X AT24CS04-MAHM-T(2) (NiPdAu Lead Finish) 8MA2 AT24CS04-STUM-T(2) 5TS1 AT24CS04-WWU11M(3) Wafer Sale 1.7V to 5.5V Industrial Temperature (–40C to 85C) Package Type 8S1 8-lead, 0.150" wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8X 8-lead, 4.4mm body, Plastic Thin Shrink Small Outline (TSSOP) 8MA2 8-pad, 2.00mm x 3.00mm body, 0.50mm pitch, Dual No Lead (UDFN) 5TS1 5-lead, 2.90mm x 1.60mm body, Plastic Thin Shrink Small Outline (SOT23)
AT24CS04/08 [DATASHEET] Atmel-8766D-SEEPROM-AT24CS04-08-Datasheet_072013
13.2 Atmel AT24CS08 Ordering Information
Additional package types that are not listed may be available. Please contact Atmel for more details. Notes: 1. Consistent with the general semiconductor market trend, Atmel will supply devices with either gold or cop- per bond wires to increase manufacturing flexibility and to ensure a long-term continuity of supply. There is no difference in product quality, reliability, or performance between the two variations. 2. T = Tape and reel SOIC = 4K units per reel TSSOP, UDFN, and SOT23 = 5K units per reel 3. For Wafer sales, please contact Atmel Sales. Atmel Ordering Code(1) Package Voltage Operation Range AT24CS08-SSHM-T(2) (NiPdAu Lead Finish) 8S1 1.7V to 5.5V Lead-free/Halogen-free/ Industrial Temperature (–40C to 85C) AT24CS08-XHM-T(2) (NiPdAu Lead Finish) 8X AT24CS08-MAHM-T(2) (NiPdAu Lead Finish) 8MA2 AT24CS08-STUM-T(2) 5TS1 AT24CS08-WWU11M(3) Wafer Sale 1.7V to 5.5V Industrial Temperature (–40C to 85C) Package Type 8S1 8-lead, 0.150" wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8X 8-lead, 4.4mm body, Plastic Thin Shrink Small Outline (TSSOP) 8MA2 8-pad, 2.00mm x 3.00mm body, 0.50mm pitch, Dual No Lead (UDFN) 5TS1 5-lead, 2.90mm x 1.60mm body, Plastic Thin Shrink Small Outline (SOT23)
19AT24CS04/08 [DATASHEET] Atmel-8766D-SEEPROM-AT24CS04-08-Datasheet_072013 14. Packaging Information 14.1 8S1 — 8-lead JEDEC SOIC DRAWING NO. REV. TITLE GPC COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 A 1.35 – 1.75 b 0.31 – 0.51 C 0.17 – 0.25 D 4.80 – 5.05 E1 3.81 – 3.99 E 5.79 – 6.20 e 1.27 BSC L 0.40 – 1.27 ØØ 0° – 8° Ø E N TOP VIEW C END VIEW A b L e D SIDE VIEW Package Drawing Contact: packagedrawings@atmel.com 8S1 G 6/22/11 Notes: This drawing is for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 8S1, 8-lead (0.150” Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) SWB
AT24CS04/08 [DATASHEET] Atmel-8766D-SEEPROM-AT24CS04-08-Datasheet_072013 14.2 8X — 8-lead TSSOP DRAWING NO. REV. TITLE GPC COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A - - 1.20 A1 0.05 - 0.15 A2 0.80 1.00 1.05 D 2.90 3.00 3.10 2, 5 E 6.40 BSC E1 4.30 4.40 4.50 3, 5 b 0.19 – 0.30 4 e 0.65 BSC L 0.45 0.60 0.75 L1 1.00 REF C 0.09 - 0.20 Side View End ViewTop View A L D N b Pin 1 indicator this corner E e Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimension D and E1 to be determined at Datum Plane H. H Package Drawing Contact: packagedrawings@atmel.com 8X E 12/8/11 8X, 8-lead 4.4mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) TNR C
21AT24CS04/08 [DATASHEET] Atmel-8766D-SEEPROM-AT24CS04-08-Datasheet_072013 14.3 8MA2 — 8-pad UDFN TITLE DRAWING NO. GPC REV. Package Drawing Contact: packagedrawings@atmel.com 8MA2YNZ C 8MA2, 8-pad, 2 x 3 x 0.6 mm Body, Thermally Enhanced Plastic Ultra Thin Dual Flat No Lead Package (UDFN) COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 1.90 2.00 2.10 E 2.90 3.00 3.10 D2 1.40 1.50 1.60 E2 1.20 1.30 1.40 A 0.50 0.55 0.60 A1 0.0 0.02 0.05 A2 – – 0.55 C 0.152 REF L 0.30 0.35 0.40 e 0.50 BSC b 0.18 0.25 0.30 3 K 0.20 – – 9/6/12 E e (6x) L (8x) b (8x) Pin#1 ID A Pin 1 ID D C K
AT24CS04/08 [DATASHEET] Atmel-8766D-SEEPROM-AT24CS04-08-Datasheet_072013 14.4 5TS1 — 5-lead SOT23 DRAWING NO. REV. TITLE GPC Package Drawing Contact: packagedrawings@atmel.com 5TS1 D 5/31/12 5TS1, 5-lead 1.60mm Body, Plastic Thin Shrink Small Outline Package (Shrink SOT) TSZ COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A - - 1.00 A1 0.00 - 0.10 A2 0.70 0.90 1.00 c 0.08 - 0.20 3 D 2.90 BSC 1,2 E 2.80 BSC 1,2 E1 1.60 BSC 1,2 L1 0.60 REF e 0.95 BSC e1 1.90 BSC b 0.30 - 0.50 3,4 1. Dimension D does not include mold flash, protrusions or gate burrs. Mold flash, protrusions or gate burrs shall not exceed 0.15 mm per end. Dimension E1 does not include interlead flash or protrusion. Interlead flash or protrusion shall not exceed 0.15 mm per side. 2. The package top may be smaller than the package bottom. Dimensions D and E1 are determined at the outermost extremes of the plastic body exclusive of mold flash, tie bar burrs, gate burrs and interlead flash, but including any mismatch between the top and bottom of the plastic body. 3. These dimensions apply to the flat section of the lead between 0.08 mm and 0.15 mm from the lead tip. 4. Dimension "b" does not include dambar protrusion. Allowable dambar protrusion shall be 0.08 mm total in excess of the "b" dimension at maximum material condition. The dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and an adjacent lead shall not be less than 0.07 mm. This drawing is for general information only. Refer to JEDEC Drawing MO-193, Variation AB for additional information. 5 4 L C END VIEW C AA2 b e PLANE SEATING D SIDE VIEW E TOP VIEW
23AT24CS04/08 [DATASHEET] Atmel-8766D-SEEPROM-AT24CS04-08-Datasheet_072013 15. Revision History Doc. Rev. Date Comments 8766D 07/2013 Update status from preliminary to complete release. Update footers and disclaimer page. 8766C 09/2012 Update ordering information 8766B 08/2012 Update the device address table: 4-Kbit serial number bit 1 changed from P0 to 0. 8-Kbit serial number bit 2 changed from P1 to 0 and bit 2 from P0 to 0. Update the serial number read figure’s device address. Correct figure, Serial Number Read, to change 0 to * and add note. 8766A 06/2012 Initial document release.
Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 | www.atmel.com © 2013 Atmel Corporation. / Rev.: Atmel-8766D-SEEPROM-AT24CS04-08-Datasheet_072013. Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDIT IONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS P RODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMI TATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or c ompleteness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel d oes not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automo tive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical A pplications”) without an Atmel officer's specific written consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for t he operation of nuclear facilities and weapons systems. Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.