AT24CM01 ATMEL
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 21
Technical content
Features
Low Voltage and Standard Voltage Operation Available ̶ 1.7V (VCC = 1.7V to 5.5V) ̶ 2.5V (VCC = 2.5V to 5.5V) Internally Organized 131,072 x 8 2-wire Serial Interface Schmitt Triggers, Filtered Inputs for Noise Suppression Bidirectional Data Transfer Protocol 400kHz (1.7V) and 1MHz (5V, 2.5V) Compatibility Write Protect Pin for Hardware Data Protection 256-byte Page Write Mode ̶ Partial Page Writes Allowed Random and Sequential Read Modes Self-timed Write Cycle (5ms Max) High Reliability ̶ Endurance: 1,000,000 Write Cycles ̶ Data Retention: 40 Years Green Package Options (Pb/Halide-free/RoHS Compliant) ̶ 8-lead JEDEC SOIC, 8-lead EIAJ SOIC, 8-lead TSSOP, and 8-ball WLCSP Die Sale Options: Wafer Form and Tape and Reel Available
Description
The Atmel® AT24CM01 provides 1,048,576 bits of Serial Electrically Erasable and Programmable Read-Only Memory (EEPROM) organized as 131,072 words of 8 bits each. The device’s cascadable feature allows up to four devices to share a common 2-wire bus. The device is optimized for use in many industrial and commercial applications where low power and low voltage operation are essential. The devices are available in space-saving 8-lead JEDEC SOIC, 8-lead EIAJ SOIC, 8-lead TSSOP, and 8-ball WLCSP. In addition, the entire family is AT24CM01 I2C-Compatible (2-wire) Serial EEPROM 1-Mbit (131,072 x 8) DATASHEET
AT24CM01 [DATASHEET] Atmel-8812F-SEEPROM-AT24CM01-Datasheet_012015 1. Pin Configurations and Pinouts 2. Absolute Maximum Ratings* Pin Name Function NC No Connect A1 Address Input A2 Address Input GND Ground SDA Serial Data SCL Serial Clock Input WP Write Protect VCC Power Supply Note: Drawings are not to scale. 8-lead TSSOP Top View NC GND VCC WP SCL SD A NC GND VCC WP SCL SDA 8-lead SOIC Top View 8-ball WLSCP Top View VCC SDA SCL A1 WP NC A2 GND Voltage on any pin *Notice: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
3AT24CM01 [DATASHEET] Atmel-8812F-SEEPROM-AT24CM01-Datasheet_012015 3. Block Diagram 4. Pin Description Serial Clock (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative edge clock data out of each device. Serial Data (SDA): The SDA pin is bidirectional for serial data transfer. This pin is open drain driven and may be wire-ORed with any number of other open drain or open collector devices. Device Addresses (A2 and A1): The A2 and A1 pins are device address inputs that can be hardwired or left not connected for hardware compatibility with other Atmel AT24Cxx devices. When the A2 and A1 pins are hardwired, as many as four 1-Mbit devices may be addressed on a single bus system (See “Device Addressing” on page 9. for more details). If the A 2 and A1 pins are left floating, the A2 and A1 pin will be internally pulled down to GND if the capacitive coupling to the circuit board VCC plane is <3pF. If coupling is >3pF, Atmel recommends connecting the A2 and A1 pin to GND. Write Protect (WP): The Write Protect input, when connected to GND, allows normal write operations. When WP is connected high to VCC, all write operations to the memory are inhibited. If the pin is left floating, the WP pin will be internally pulled down to GND if the capacitive coupling to the circuit board VCC plane is <3pF. If coupling is >3pF, Atmel recommends connecting the pin to GND. Switching WP to VCC prior to a write operation creates a software write protect function. Table 4-1. Write Protect Start Stop Logic VCC GND WP SCL SDA Serial Control Logic EN H.V. Pump/Timing EEPROM Data Recovery Serial MUX X DEC DOUT/ACK Logic COMP LOAD INC Data Word Addr/counter Y DEC R/W DOUT DIN LOAD Device Address Comparator WP Pin Status Part of the Array Protected At VCC Full Array At GND Normal Read/Write Operations
AT24CM01 [DATASHEET] Atmel-8812F-SEEPROM-AT24CM01-Datasheet_012015 5. Memory Organization AT24CM01, 1-Mbit Serial EEPROM: The 1-Mbit is internally organized as 512 pages of 256 bytes each. Random word addressing requires a 17-bit data word address.
5.1 Pin Capacitance
Table 5-1. Pin Capacitance (1) Note: 1. This parameter is characterized and is not 100% tested.
5.2 DC Characteristics
Table 5-2. DC Characteristics Note: 1. V IL min and VIH max are reference only and are not tested. Applicable over recommended operating range from TA = 25C, f = 1.0MHz, VCC = 5.5V. Symbol Test Condition Max Units Conditions CI/O Input/Output Capacitance (SDA) 8 pF VI/O = 0V CIN Input Capacitance (A2, A1, SCL) 6 pF VIN = 0V Applicable over recommended operating range from: TAI = -40C to +85C, VCC = 1.7V to 5.5V (unless otherwise noted). Symbol Parameter Test Condition Min Typ Max Units VCC1 Supply Voltage, 1.7V Option 1.7 5.5 V VCC2 Supply Voltage, 2.5V Option 2.5 5.5 V ICC Supply Current VCC = 5.0V Read at 400kHz 2.0 mA ICC Supply Current VCC = 5.0V Write at 400kHz 3.0 mA ISB Standby Current VCC = 1.7V VIN = VCC or VSS 1.0 μA VCC = 2.5V 2.0 μA VCC = 3.6V VIN = VCC or VSS 3.0 μA VCC = 5.5V 6.0 μA ILI Input Leakage Current VIN = VCC or VSS 0.10 3.0 μA ILO Output Leakage Current VOUT = VCC or VSS 0.05 3.0 μA VIL Input Low Level(1) -0.6 VCC x 0.3 V VIH Input High Level(1) VCC x 0.7 VCC + 0.5 V VOL1 Output Low Level VCC = 1.7V IOL = 0.15mA 0.2 V VOL2 Output Low Level VCC = 3.0V IOL = 2.1mA 0.4 V
5AT24CM01 [DATASHEET] Atmel-8812F-SEEPROM-AT24CM01-Datasheet_012015
5.3 AC Characteristics
Table 5-3. AC Characteristics Notes: 1. This parameter is ensured by characterization only. 2. AC measurement conditions: RL (connects to VCC): 1.3 k (2.5V, 5V), 10 k (1.7V) Input pulse voltages: 0.3 VCC to 0.7 VCC Input rise and fall times: 50ns Input and output timing reference voltages: 0.5 VCC Applicable over recommended operating range from TAI = -40C to +85C, VCC = 1.7V to 5.5V (where applicable), CL = 100pF (unless otherwise noted). Test conditions are listed in Note 2. Symbol Parameter 1.7V 2.5V, 5.0V UnitsMin Max Min Max fSCL Clock Frequency, SCL 400 1000 kHz tLOW Clock Pulse Width Low 1300 400 ns tHIGH Clock Pulse Width High 600 400 ns tI Noise Suppression Time(1) 100 50 ns tAA Clock Low to Data Out Valid 50 900 50 550 ns tBUF Time the bus must be free before a new transmission can start(1) 1300 500 ns tHD.STA Start Condition Hold Time 600 250 ns tSU.STA Start Condition Set-up Time 600 250 ns tHD.DAT Data In Hold Time 0 0 ns tSU.DAT Data In Set-up Time 100 100 ns tR Inputs Rise Time(1) 300 300 ns tF Inputs Fall Time(1) 300 100 ns tSU.STO Stop Condition Set-up Time 600 250 ns tDH Data Out Hold Time 50 50 ns tWR Write Cycle Time 5 5 ms Endurance(1) 25°C, Page Mode, 3.3V 1,000,000 Write Cycles
AT24CM01 [DATASHEET] Atmel-8812F-SEEPROM-AT24CM01-Datasheet_012015 Page Write: The 1-Mbit EEPROM is capable of a 256-byte Page Write. A Page Write is initiated the same way as a Byte Write, but the microcontroller does not send a Stop condition after the first data word is clocked in. Instead, after the EEPROM acknowledges receipt of the first data word, the microcontroller can transmit up to 255 more data words. The EEPROM will respond with an acknowledge after each data word is received. The microcontroller must terminate the page write sequence with a Stop condition (Figure 8-2) and the internally timed write cycle will begin. The data word address lower 8 bits are internally incremented following the receipt of each data word. The higher data word address bits are not incremented, retaining the memory page row location. When the internally generated word address, reaches the page boundary, the following byte is placed at the beginning of the same page. If more than 256 data words are transmitted to the EEPROM, the data word address will “roll over” and previous data will be overwritten. The address “rollover” during write is from the last byte of the current page to the first byte of the same page. Figure 8-2. Page Write Acknowledge Polling: Once the internally timed write cycle has started and the EEPROM inputs are disabled, Acknowledge Polling can be initiated. This involves sending a Start condition followed by the device address word. The read/write bit is representative of the operation desired. Only if the internal write cycle has completed will the EEPROM respond with a zero, allowing a new read or write sequence to be initiated. Data Security: The AT24CM01 has a hardware data protection scheme that allows the user to write protect the entire memory when the WP pin is at V CC. SDA LINE S T O P S T A R T W R I T E Device Address First Word Address Second Word Address Data (n) Data (n + x) M S B A C K P A C K L S B L S B A C K A C K A C K R W
AT24CM01 [DATASHEET] Atmel-8812F-SEEPROM-AT24CM01-Datasheet_012015 Sequential Read: Sequential Reads are initiated by either a Current Address Read or a Random Read. After the microcontroller receives a data word, it responds with an acknowledge. As long as the EEPROM receives an acknowledge, it will continue to increment the data word address and serially clock out sequential data words. When the memory address limit is reached, the data word address will “roll over” and the sequential read will continue. The Sequential Read operation is terminated when the microcontroller does not respond with a zero, but does generate a following Stop condition. Figure 9-3. Sequential Read SDA LINE S T A R T S T A R T R E A D W R I T E S T O P Device Address Second Word Address Device Address First Word Address Data (n + 1) Data (n + 2) Data (n + x)Data (n) M S B A C K P A C K A C K L S B A C K A C K A C K A C K N O A C K R W Dummy Write . . . . . . P R W
13AT24CM01 [DATASHEET] Atmel-8812F-SEEPROM-AT24CM01-Datasheet_012015 10. Ordering Code Detail Atmel Designator Product Family 24C = Standard I2C Serial EEPROM Device Density Shipping Carrier Option Package Device Grade or Wafer/Die Thickness Package Option M = Megabit Family 01 = 1 Megabit B or blank = Bulk (Tubes) T = Tape and Reel Operating Voltage M = 1.7V to 5.5V D = 2.5V to 5.5V H = Green, NiPdAu Lead Finish Industrial Temperature Range (-40°C to +85°C) U = Green, Matte Sn Lead Finish Industrial Temperature Range (-40°C to +85°C) 11 = 11mil Wafer Thickness SS = JEDEC SOIC S = EIAJ SOIC X = TSSOP U = 3x5 Grid Array, WLCSP WWU = Wafer Unsawn AT24CM01-SSHM-B
AT24CM01 [DATASHEET] Atmel-8812F-SEEPROM-AT24CM01-Datasheet_012015 11. Part Markings DRAWING NO. REV. TITLE 24CM01SM F 12/12/14 DL-CSO-Assy_eng@atmel.com AAAAAAAA###% @ATMLHYWW 8-lead SOIC 8-lead TSSOP AAAAAAA ###% @ ATHYWW 8-ball WLCSP Note 2: Package drawings are not to scale Note 1: designates pin 1 AT24CM01: Package Marking Information Catalog Number Truncation AT24CM01 Truncation Code ###: 2G Date Codes Voltages Y = Year M = Month WW = Work Week of Assembly % = Minimum Voltage 4: 2014 8: 2018 A: January 02: Week 2 D: 2.5V min 5: 2015 9: 2019 B: February 04: Week 4 M: 1.7V min 7: 2017 1: 2021 L: December 52: Week 52 Country of Assembly Lot Number Grade/Lead Finish Material @ = Country of Assembly AAA...A = Atmel Wafer Lot Number H: Industrial/NiPdAu U: Industrial/Matte Tin/SnAgCu Trace Code Atmel Truncation XX = Trace Code (Atmel Lot Numbers Correspond to Code) AT: Atmel Example: AA, AB.... YZ, ZZ ATM: Atmel ATML: Atmel ### YXX 8-lead EIAJ AAAAAAAA ###% @ ATMLHYWW
15AT24CM01 [DATASHEET] Atmel-8812F-SEEPROM-AT24CM01-Datasheet_012015 12. Ordering Information Notes: 1. WLCSP Package — CAUTION: Exposure to ultraviolet (UV) light can degrade the data stored in the EEPROM cells. Therefore, customers who use a WLCSP product must ensure that exposure to ultraviolet light does not occur. 2. For wafer sales, please contact Atmel Sales. Atmel Ordering Code Lead Finish Package Voltage Delivery Information Operation RangeForm Quantity AT24CM01-SSHM-B NiPdAu (Lead-free/Halogen-free) 8S1 1.7V to 5.5V Bulk (Tubes) 100 per Tube Industrial Temperature (-40C to 85C) AT24CM01-SSHM-T Tape and Reel 4,000 per Reel AT24CM01-SSHD-B 2.5V to 5.5V Bulk (Tubes) 100 per Tube AT24CM01-SSHD-T Tape and Reel 4,000 per Reel AT24CM01-SHM-B 8S2 1.7V to 5.5V Bulk (Tubes) 95 per Tube AT24CM01-SHM-T Tape and Reel 2,000 per Reel AT24CM01-SHD-B 2.5V to 5.5V Bulk (Tubes) 95 per Tube AT24CM01-SHD-T Tape and Reel 2,000 per Reel AT24CM01-XHM-B 1.7V to 5.5V Bulk (Tubes) 100 per Tube AT24CM01-XHM-T Tape and Reel 5,000 per Reel AT24CM01-XHD-B 2.5V to 5.5V Bulk (Tubes) 100 per Tube AT24CM01-XHD-T Tape and Reel 5,000 per Reel AT24CM01-UUM-T(1) SnAgCu (Lead-free/Halogen-free) 8U-6 1.7V to 5.5V Tape and Reel 5,000 per Reel AT24CM01-WWU11M(2) N/A Wafer Sale Note 2 Package Type 8S1 8-lead, 0.150” wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8S2 8-lead, 0.208” wide, Plastic Gull Wing Small Outline (EIAJ SOIC) 8X 8-lead, 4.4mm body, Plastic Thin Shrink Small Outline (TSSOP) 8U-6 8-ball, 3x5 Grid Array, Wafer Level Chip Scale (WLCSP)
AT24CM01 [DATASHEET] Atmel-8812F-SEEPROM-AT24CM01-Datasheet_012015 13. Packaging Information 13.1 8S1 — 8-lead JEDEC SOIC DRAWING NO. REV. TITLE GPC COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 A 1.35 – 1.75 b 0.31 – 0.51 C 0.17 – 0.25 D 4.80 – 5.05 E1 3.81 – 3.99 E 5.79 – 6.20 e 1.27 BSC L 0.40 – 1.27 ØØ 0° – 8° Ø E N TOP VIEW C END VIEW A b L e D SIDE VIEW Package Drawing Contact: packagedrawings@atmel.com 8S1 G 6/22/11 Notes: This drawing is for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 8S1, 8-lead (0.150” Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) SWB
17AT24CM01 [DATASHEET] Atmel-8812F-SEEPROM-AT24CM01-Datasheet_012015 13.2 8S2 — 8-lead EIAJ SOIC DRAWING NO. REV. TITLE GPC 8S2, 8-lead, 0.208” Body, Plastic Small Outline Package (EIAJ) 8S2 G 11/10/14 STNPackage Drawing Contact: packagedrawings@atmel.com COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE Notes: 1. This drawing is for general information only; refer to EIAJ Drawing EDR-7320 for additional information. 2. Mismatch of the upper and lower dies and resin burrs aren't included. 3. Determines the true geometric position. 4. Values b,C apply to plated terminal. The standard thickness of the plating layer shall measure between 0.007 to .021 mm. A 1.70 2.16 A1 0.05 0.25 b 0.35 0.48 4 C 0.15 0.35 4 D 5.13 5.35 E1 5.18 5.40 2 E 7.70 8.26 L 0.51 0.85 q 0° 8° e 1.27 BSC 3 q E TOP VIEW C END VIEW A b L e D SIDE VIEW
AT24CM01 [DATASHEET] Atmel-8812F-SEEPROM-AT24CM01-Datasheet_012015 13.3 8X — 8-lead TSSOP DRAWING NO. REV. TITLE GPC COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A - - 1.20 A1 0.05 - 0.15 A2 0.80 1.00 1.05 D 2.90 3.00 3.10 2, 5 E 6.40 BSC E1 4.30 4.40 4.50 3, 5 b 0.19 0.25 0.30 4 e 0.65 BSC L 0.45 0.60 0.75 L1 1.00 REF C 0.09 - 0.20 Side View End ViewTop View A L D N b Pin 1 indicator this corner E e Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15mm (0.006in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25mm (0.010in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07mm. 5. Dimension D and E1 to be determined at Datum Plane H. Package Drawing Contact: packagedrawings@atmel.com 8X E 2/27/14 8X, 8-lead 4.4mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) TNR C
19AT24CM01 [DATASHEET] Atmel-8812F-SEEPROM-AT24CM01-Datasheet_012015 13.4 8U-6 — 8-ball WLCSP DRAWING NO. REV. TITLE GPC 8U-6 B 4/25/13 8U-6, 8-ball (3x5 Array) Wafer Level Chip Scale Package (WLCSP) GHZ COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN TYP MAX NOTE A 0.460 0.499 0.538 A1 0.164 - 0.224 A2 0.280 0.305 0.330 E Contact Atmel for details e 0.866 e2 0.500 d 1.000 d2 0.500 D Contact Atmel for details b 0.239 0.269 0.299 Package Drawing Contact: packagedrawings@atmel.com TOP VIEW SIDE VIEW BALL SIDE Pin Assignment Matrix A B C D E WP V CC SDA D E e d ØbPin 1 Pin 1 A AEC SCL A1 NC GND BDA ECBD d 0.015 C A 4X d 0.075 C C j n0.015m C j n0.05m CAB * Dimensions are NOT to scale.
AT24CM01 [DATASHEET] Atmel-8812F-SEEPROM-AT24CM01-Datasheet_012015 14. Revision History Doc. No. Date Comments 8821F 01/2015 Update the ordering information section, part markings, and the 8X and 8S2 package outline drawings. 8821E 03/2013 Update document status from preliminary to complete. Correct WLCSP pinout. Update footers and disclaimer page. 8812D 01/2013 Correct TSSOP pin label 7 to WP. 8812C 12/2012 Add WLCSP package. Update part markings. Update pinout diagram. Update part markings. Correct Byte Write figure from second typo error to first word address. Update Sequential Read figure. 8812B 07/2012 Correct ordering code: - AT24CM01-WWU-11, Die Sale to AT24CM01-WWU11M, Wafer Sale. Update Atmel logos and disclaimer page. 8812A 05/2012 Initial document release.
Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 | www.atmel.com © 2015 Atmel Corporation. / Rev.: Atmel-8812F-SEEPROM-AT24CM01-Datasheet_012015. Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, and others are registered trademarks or trademarks of Atmel Corporation in U.S. and other countries. Other terms and product names may be trademarks of others. DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDIT IONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS P RODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMI TATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or c ompleteness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel d oes not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automo tive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical A pplications”) without an Atmel officer's specific written consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for t he operation of nuclear facilities and weapons systems. Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.