AT24C64B_07 ATMEL
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 16
Technical content
Features
- Low-voltage and Standard-voltage Operation Low-power Devices (ISB = 6 µA at 5.5V) Available Internally Organized 8192 x 8 2-Wire Serial Interface Schmitt Trigger, Filtered Inputs for Noise Suppression Bi-directional Data Transfer Protocol 400 kHz Clock Rate Write Protect Pin for Hardware Data Protection 32-Byte Page Write Mode (Partial Page Writes Allowed) Self-Timed Write Cycle (5 ms max) High Reliability – Endurance: 1 Million Write Cycles – Data Retention: 100 Years Lead-free/Halogen-free Devices Available 8-lead JEDEC SOIC and 8-lead TSSOP Packages Die Sales: Wafer Form, Waffle Pack, and Bumped Wafers
Description
The AT24C64B provides 65,536 bits of se rial electrically erasable and programmable read only memory (EEPROM) organized as 8 192 words of 8 bits each. The device’s cascadable feature allows up to 8 devices to share a common 2-wire bus. The device is optimized for use in many industrial and commercial applications where low power and low voltage operation are essential. The AT24C64B is available in space saving 8-lead JEDEC SOIC and 8-lead TSSOP packages and is accessed via a 2-wire serial to 5.5V) versions. 2-Wire Serial EEPROM 64K (8192 x 8) AT24C64B 3350E–SEEPR–9/07 2-Wire, 32K Serial E 2PROM Pin Configurations Pin Name Function A0 - A2 Address Inputs SDA Serial Data SCL Serial Clock Input WP Write Protect 8-lead SOIC GND VCC WP SCL SDA 8-lead TSSOP GND VCC WP SCL SDA
3350E–SEEPR–9/07 AT24C64B 1. Block Diagram 2. Pin Description SERIAL CLOCK (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative edge clock data out of each device. SERIAL DATA (SDA): The SDA pin is bidirectional for serial data transfer. This pin is open-drain driven and may be wire-ORed with any number of other open-drain or open collector devices. DEVICE/ADDRESSES (A2, A1, A0): The A2, A1 and A0 pins are device address inputs that are hard wired or left not connected for hardw are compatibility with other AT24CXX devices. When the pins are hardwired, as many as eight 64K devices may be addressed on a single bus system (device addressing is discussed in detail under the Device Addressing section). If the pins are left floating, the A2, A1 and A0 pins will be inte rnally pulled down to GND if the capacitive cou- Absolute Maximum Ratings* Maximum Ratings” may cause permanent dam- age to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Voltage on Any Pin START STOP LOGIC VCC GND WP SCL SDA SERIAL CONTROL LOGIC EN H.V. PUMP/TIMING EEPROM DATA RECOVERY SERIAL MUX X DEC DOUT/ACK LOGIC COMP LOAD INC DATA WORD ADDR/COUNTER Y DEC R/W DOUT DIN LOAD DEVICE ADDRESS COMPARATOR
3350E–SEEPR–9/07 AT24C64B pling to the circuit board V CC plane is <3pF. If coupling is > 3pF, Atmel recommends connecting the address pins to GND. WRITE PROTECT (WP): The write protect input, when connected to GND, allows normal write operations. When WP is connected high to VCC, all write operations to the upper quandrant (16K bits) of memory are inhibited. If the pin is left floating, the WP pin will be internally pulled down to GND if the capacitive coupling to the circuit board V CC plane is <3pF. If coupling is >3pF, Atmel recommends connecting the pin to GND. 3. Memory Organization AT24C64B, 64K SERIAL EEPROM: The 64K is internally organized as 256 pages of 32 bytes each. Random word addressing requires a 13 bit data word address. Note: 1. This parameter is characterized and is not 100% tested. Note: 1. V IL min and VIH max are reference only and are not tested. Pin Capacitance(1) Applicable over recommended operating range from TA = 25°C, f = 1.0 MHz, VCC = +1.8V Symbol Test Condition Max Units Conditions CI/O Input/Output Capacitance (SDA) 8 pF V I/O = 0V CIN Input Capacitance (A0, A1, A2, SCL) 6 pF V IN = 0V DC Characteristics Applicable over recommended operating range from: TAI = -40 to +85°C, VCC = +1.8 to +5.5V (unless otherwise noted) Symbol Parameter Test Condition Min Typ Max Units VCC1 Supply Voltage 1.8 5.5 V VCC2 Supply Voltage 2.7 5.5 V VCC3 Supply Voltage 4.5 5.5 V ICC1 Supply Current V CC = 5.0V READ at 400 kHz 0.4 1.0 mA ICC2 Supply Current V CC = 5.0V WRITE at 400 kHz 2.0 3.0 mA ISB1 Standby Current (1.8V option) VCC = 1.8V V IN = VCC or VSS 1.0 μA ISB2 Standby Current (2.7V option) VCC = 2.7V V IN = VCC or VSS 2.0 μA ISB3 Standby Current (5V option) VCC = 4.5 - 5.5V V IN = VCC or VSS 6.0 μA ILI Input Leakage Current VIN = VCC or VSS 0.10 3.0 μA ILO Output Leakage Current VOUT = VCC or VSS 0.05 3.0 μA VIL Input Low Level(1) -0.6 V CC x 0.3 V VIH Input High Level(1) VCC x 0.7 V CC + 0.5 V VOL2 Output Low Level V CC = 3.0V I OL = 2.1 mA 0.4 V VOL1 Output Low Level V CC = 1.8V I OL = 0.15 mA 0.2 V
3350E–SEEPR–9/07 AT24C64B Notes: 1. This parameter is characterized and is not 100% tested (T A = 25°C) 2. This parameter is characterized and is not 100% tested. 4. AC Characteristics Applicable over recommended operating range from TAI = -40°C to +85°C, VCC = +1.8V to +5.5V, CL = 1 TTL Gate and 100 pF (unless otherwise noted) Symbol Parameter AT24C64B Units 1.8V – 3.6V 5.0V Min Max Min Max fSCL Clock Frequency, SCL 400 400 kHz tLOW Clock Pulse Width Low 1.3 1.2 µs tHIGH Clock Pulse Width High 0.6 0.6 µs tI Noise Suppression Time(1) 100 50 ns tAA Clock Low to Data Out Valid 0.2 0.9 0.1 0.9 µs tBUF Time the bus must be free before a new transmission can start(2) 1.3 1.2 µs tHD.STA Start Hold Time 0.6 0.6 µs tSU.STA Start Set-up Time 0.6 0.6 µs tHD.DAT Data In Hold Time 0 0 µs tSU.DAT Data In Set-up Time 100 100 ns tR Inputs Rise Time(2) 0.3 0.3 µs tF Inputs Fall Time(2) 300 300 ns tSU.STO Stop Set-up Time 0.6 0.6 µs tDH Data Out Hold Time 200 50 ns tWR Write Cycle Time 5 5 ms Endurance(1 ) 5.0V, 25°C, Page Mode 1M 1M Write Cycles
3350E–SEEPR–9/07 AT24C64B 5. Device Operation CLOCK and DATA TRANSITIONS: The SDA pin is normally pul led high with an external device. Data on the SDA pin may change only during SCL low time periods (refer to Data Valid- ity timing diagram). Data changes during SCL high periods will i ndicate a start or stop condition as defined below. START CONDITION: A high-to-low transition of SDA with SCL high is a start condition which must precede any other command (refer to Start and Stop Definition timing diagram). STOP CONDITION: A low-to-high transition of SDA with SCL high is a stop condition. After a read sequence, the stop command will place the EEPROM in a standby power mode (refer to Start and Stop Definition timing diagram). ACKNOWLEDGE: All addresses and data words are serially transmitted to and from the EEPROM in 8-bit words. The EEPROM sends a zero during the ninth clock cycle to acknowl- edge that it has received each word. STANDBY MODE: The AT24C64B features a low power standby mode which is enabled: a) upon power-up and b) after the receipt of the Stop bit and the completion of any internal operations. MEMORY RESET: After an interruption in protocol, power loss or system reset, any 2-wire part can be reset by following these steps: (a) Clock up to 9 cycles, (b) look for SDA high in each cycle while SCL is high and then (c) create a start condition as SDA is high.
3350E–SEEPR–9/07 AT24C64B 6. Bus Timing SCL: Serial Clock, SDA: Serial Data I/O 7. Write Cycle Timing SCL: Serial Clock, SDA: Serial Data I/O Note: 1. The write cycle time t WR is the time from a valid stop condition of a write sequence to the end of the internal clear/write cycle. SCL SDA IN SDA OUT tF tHIGH tLOW tLOW tR tAA tDH tBUF twr (1) STOP CONDITION START CONDITION WORDn ACK8th BIT SCL SDA
3350E–SEEPR–9/07 AT24C64B 8. Data Validity 9. Start and Stop Definition 10. Output Acknowledge SDA SCL DATA STABLE DATA STABLE DATA CHANGE SDA SCL START STOP SCL DATA IN DATA OUT START ACKNOWLEDGE 981
3350E–SEEPR–9/07 AT24C64B 11. Device Addressing The 64K EEPROM requires an 8-bit device address word following a start condition to enable the chip for a read or write operation (see Figure 13-1 on page 11). The device address word consists of a mandatory one, zero sequence for the first four most significant bits as shown. This is common to all 2-wire EEPROM devices. The 64K uses the three device address bits A2, A1, A0 to allow as many as eight devices on the same bus. These bits must compare to their corresponding hardwired input pins. The A2, A1, and A0 pins use an internal proprietary circuit that biases them to a logic low condition if the pins are allowed to float. The eighth bit of the device address is the read/write operation select bit. A read operation is ini- tiated if this bit is high and a write operation is initiated if this bit is low. Upon a compare of the device address, the EEPROM will outpu t a zero. If a compare is not made, the device will return to standby state. NOISE PROTECTION: Special internal circuitry placed on the SDA and SCL pins prevent small noise spikes from activating the device. A low-V CC detector (5-volt option) resets the device to prevent data corruption in a noisy environment. DATA SECURITY: The AT24C64B has a hardware data protection scheme that allows the user to write protect the upper quadrant (16K bits) of memory when the WP pin is at VCC. 12. Write Operations BYTE WRITE: A write operation requires two 8-bit data word addresses following the device address word and acknowledgment. Upon receipt of this address, the EEPROM will again respond with a zero and then clock in the first 8-bit data word. Following receipt of the 8-bit data word, the EEPROM will output a ze ro and the addr essing device, such as a microcontroller, must terminate the writ e sequence with a stop condition. At this time the EEPROM enters an internally-timed write cycle, t WR, to the nonvolatile memory. All inputs are disabled during this write cycle and the EEPROM will not respond until the write is complete (see Figure 13-2 on page 11). PAGE WRITE: The 64K EEPROM is capable of 32-byte page writes. A page write is initiated the same way as a byte write, but the microcontroller does not send a stop condition after the first data word is cl ocked in. Instead, after the EEPROM acknowledges receipt of the first data word, the microcontroller can transmit up to 31 more data words. The EEPROM will respond with a zero after each data word received. The microcontroller must ter- minate the page write sequence with a stop condition (see Figure 13-3 on page 11). The data word address lower 5 bits are internally incremented following the receipt of each data word. The higher data word address bits are not incremented, retaining the memory page row location. When the word address, internally generated, reaches the page boundary, the follow- ing byte is placed at the beginning of the same page. If more than 32 data words are transmitted to the EEPROM, the data word address will “roll over” and previous data will be overwritten. ACKNOWLEDGE POLLING: Once the internally-timed write cycle has started and the EEPROM inputs are disabled, ackno wledge polling can be initiate d. This involves sending a start condition followed by the device address word. The read/write bit is representative of the operation desired. Only if th e internal write cycle has comp leted will the EEPROM respond with a zero, allowing the read or write sequence to continue.
3350E–SEEPR–9/07 AT24C64B 13. Read Operations Read operations are initiated the same way as write operations with the exception that the read/write select bit in the device address word is set to one. There are three read operations: current address read, random address read and sequential read. CURRENT ADDRESS READ: The internal data word address counter maintains the last address accessed during the last read or write operation, incremented by one. This address stays valid between operations as long as the chip power is maintained. The address “roll over” during read is from the last byte of the last memory page, to the first byte of the first page. The address “roll over” during write is from the last byte of the current page to the first byte of the same page. Once the device address with the read/write select bit set to one is clocked in and acknowledged by the EEPROM, the current address data word is serially clocked out. The microcontroller does not respond with an input zero but does generate a following stop condition (see Figure 13-4 on page 12). RANDOM READ: A random read requires a “dummy” byte write sequence to load in the data word address. Once the device address word and data word address are clocked in and acknowledged by the EEPROM, the microcontroller must generate another start condition. The microcontroller now initiates a current address read by sending a device address with the read/write select bit high. The EEPROM acknowl edges the device address and serially clocks out the data word. The microcontroller does not respond with a zero but does generate a follow- ing stop condition (see Figure 13-5 on page 12). SEQUENTIAL READ: Sequential reads are initiated by either a current address read or a ran- dom address read. After the microcontroller receives a data word, it responds with an acknowledge. As long as the EEPROM receives an acknowledge, it will continue to increment the data word address and serially clock out sequential data words. When the memory address limit is reached, the data word address will “roll over” and the sequential read will continue. The sequential read operation is terminated when the microcontroller does not respond with a zero but does generate a following stop condition (see Figure 13-6 on page 12). Figure 13-1. Device Address
3350E–SEEPR–9/07 AT24C64B 2. “U” designates Green Package & RoHS compliant. 3. Available in waffle pack and wafer form; order as SL788 for inkless wafer form. Bumped die available upon request. Please contact Serial Marketing. Ordering Code Package Operation Range AT24C64BN-10SU-2.7(2) AT24C64BN-10SU-1.8(2) AT24C64B-10TU-2.7(2) AT24C64B-10TU-1.8(2) 8S1 8S1 8A2 8A2 Lead-free/Halogen-free Industrial Temperature (-40°C to 85°C) AT24C64B-W1.8-11 (3) Die Sale Industrial Temperature (-40°C to 85°C) Package Type 8S1 8-lead, 0.150” Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 4.4 mm Body, Plastic, Thin Shrink Small Outline Package (TSSOP) Options -2.7 Low Voltage (2.7V to 5.5V) -1.8 Low Voltage (1.8V to 5.5V)
3350E–SEEPR–9/07 AT24C64B 14. Packaging Information 8S1 – JEDEC SOIC 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. Note: 3/17/05 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) 8S1 C COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. A 1.35 – 1.75 b 0.31 – 0.51 C 0.17 – 0.25 D 4.80 – 5.05 E1 3.81 – 3.99 E 5.79 – 6.20 e 1.27 BSC L 0.40 – 1.27 θ 0˚ – 8˚ ØØ EE NN TOP VIEWTOP VIEW CC E1E1 END VIEW AA bb LL A1A1 ee DD SIDE VIEWSIDE VIEW
3350E–SEEPR–9/07 AT24C64B 8A2 – TSSOP
2325 Orchard Parkway
San Jose, CA 95131 TITLE DRAWING NO. R REV. 5/30/02 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 2.90 3.00 3.10 2, 5 E 6.40 BSC E1 4.30 4.40 4.50 3, 5 A – – 1.20 A2 0.80 1.00 1.05 b 0.19 – 0.30 4 e 0.65 BSC L 0.45 0.60 0.75 L1 1.00 REF 8A2, 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimension D and E1 to be determined at Datum Plane H. 8A2 B Side View End ViewTop View A L D 123 N b Pin 1 indicator this corner E e
3350E–SEEPR–9/07 AT24C64B
Revision History
Doc. Rev. Date Comments 3350E 9/2007 Updated to new template; implemented revision history.
3350E–SEEPR–9/07 Headquarters International Atmel Corporation San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Room 1219 Chinachem Golden Plaza
77 Mody Road Tsimshatsui
Tel: (852) 2721-9778 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309
78054 Saint-Quentin-en-
9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Product Contact Web Site www.atmel.com Technical Support s_eeprom@atmel.com Sales Contact www.atmel.com/contacts Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL ’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL ’S WEB SITE, ATMEL ASSUMES NO LI ABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTOR Y WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICU LAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR I NCIDEN- TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATME L HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or comp leteness of the contents of this document and reserves the rig ht to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained her ein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not int ended, authorized, or warranted for use as components in applications in tended to support or sustain life. © 2007 Atmel Corporation. All rights reserved. Atmel ®, logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.