DATASHEET SEARCH SITE

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 19

Technical content

Features

 Standard-Voltage Operation ̶ 2.7 (VCC = 2.7V to 5.5V)  Internally Organized 8,192 x 8 (64K)  Automotive Temperature Range –40C to +125C  2-Wire Serial Interface  Schmitt Trigger, Filtered Inputs for Noise Suppression  Bidirectional Data Transfer Protocol  400kHz Clock Rate  Write Protect Pin for Hardware Data Protection  32-byte Page Write Mode (Partial Page Writes Allowed)  Self-timed Write Cycle (5ms Max)  High Reliability ̶ Endurance: 1,000,000 Write Cycles ̶ Data Retention: 100 Years  Lead-free/Halogen-free Devices Available  8-lead JEDEC SOIC and 8-lead TSSOP Packages

Description

The Atmel® AT24C64B provides 65,536 bits of Serial Electrically Erasable and Programmable Read-Only Memory (EEPROM) organized as 8,192 words of 8 bits each. The device’s cascadable feature allows up to eight devices to share a common 2-wire bus. The device is optimized for use in many automotive applications where low power and low voltage operation are essential. The AT24C64B is available in space saving 8-lead JEDEC SOIC and 8-lead TSSOP packages and is accessed via a 2-wire serial interface and is available in a 2.7V (2.7V to 5.5V) version. AT24C64B 2-Wire Automotive Serial EEPROM 64-Kbit (8,192 x 8) DATASHEET

  1. Pin Configurations and Pinouts

Figure 1. Pin Configurations

  1. Absolute Maximum Ratings*

Note: Drawings are not to scale.

3AT24C64B Automotive [DATASHEET] Atmel-8778B-SEEPROM-AT24C64B-Auto-Datasheet_082014 3. Block Diagram Figure 3-1. Block Diagram 4. Pin Description Serial Clock (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative edge clock data out of each device. Serial Data (SDA): The SDA pin is bidirectional for serial data transfer. This pin is open-drain driven and may be wire-ORed with any number of other open-drain or open collector devices. Device Address (A2, A1, and A0): The A2, A1, and A0 pins are device address inputs that are hardwired or left not connected for hardware compatibility with other AT24Cxx devices. When the pins are hardwired, as many as eight 64K devices may be addressed on a single bus system (see Section 7., “Device Addressing”). If the pins are left floating, the A 2, A1, and A0 pins will internally be pulled down to Ground (GND) if the capacitive coupling to the circuit board VCC plane is less than 3pF. If coupling is greater than 3pF, Atmel recommends connecting the address pins to GND. Write Protect (WP): The Write Protect input, when connected to GND, allows normal write operations. When WP is connected high to V CC, all write operations to upper quadrant of the memory are inhibited. If the pin is left floating, the WP pin will be internally pulled down to GND if the capacitive coupling to the circuit board V CC plane is less than 3pF. If coupling is greater than 3pF, Atmel recommends connecting the pin to GND. Switching WP to V CC prior to a write operation creates a software write protect function. Start Stop Logic VCC GND WP SCL SDA Serial Control Logic EN H.V. Pump/Timing EEPROM Data Recovery Serial MUX X DEC DOUT/ACK Logic COMP LOAD INC Data Word ADDR/Counter Y DEC R/W DOUT DIN LOAD Device Address Comparator

AT24C64B Automotive [DATASHEET] Atmel-8778B-SEEPROM-AT24C64B-Auto-Datasheet_082014 5. Memory Organization AT24C64B, 64K Serial EEPROM: The 64K is internally organized as 256 pages of 32 bytes each. Random word addressing requires a 13-bit data word address.

5.1 Pin Capacitance

Table 5-1. Pin Capacitance (1) Note: 1. This parameter is characterized and is not 100% tested.

5.2 DC Characteristics

Table 5-2. DC Characteristics Note: 1. V IL min and VIH max are reference only and are not tested. Applicable over recommended operating range from TA = 25C, f = 1.0MHz, VCC = 5.5V. Symbol Test Condition Max] Units Conditions CI/O Input/Output Capacitance (SDA) 8 pF VI/O =0 V CIN Input Capacitance (A0, A1, A2, SCL) 6 pF VIN =0 V Applicable over recommended operating range from: TA = -40C to +125C, VCC = +2.7V to +5.5V (unless otherwise noted). Symbol Parameter Test Condition Min Typ Max Units VCC3 Supply Voltage 2.7 5.5 V ICC1 Supply Current VCC = 5.0V Read at 400kHz 0.4 1.0 mA ICC2 Supply Current VCC = 5.0V Write at 400kHz 2.0 3.0 mA ISB Standby Current VCC = 2.7V VIN = VCC or VSS 1.0 3.0 μA VCC = 5.0V 3.0 5.0 ILI Input Leakage Current VIN = VCC or VSS 0.10 3.0 μA ILO Output Leakage Current VOUT = VCC or VSS 0.05 3.0 μA VIL (1) Input Low Level -0.6 VCC x0 . 3 V VIH (1) Input High Level VCC x0 . 7 VCC +0 . 5 V VOL2 Output Low Level VCC = 3.0V IOL = 2.1mA 0.4 V VOL1 Output Low Level VCC = 1.8V IOL = 0.15mA 0.2 V

5AT24C64B Automotive [DATASHEET] Atmel-8778B-SEEPROM-AT24C64B-Auto-Datasheet_082014

5.3 AC Characteristics

Table 5-3. AC Characteristics Note: 1. This parameter is ensured by characterization only. Applicable over recommended operating range from TA = -40C to +125C, VCC = +2.7V to +5.5V, CL = 1 TTL Gate and 100pF (unless otherwise noted). Symbol Parameter Min Max Units fSCL Clock Frequency, SCL 400 kHz tLOW Clock Pulse Width Low 1.2 μs tHIGH Clock Pulse Width High 0.6 μs tI Noise Suppression Time(1) 50 ns tAA Clock Low to Data Out Valid 0.1 0.9 μs tBUF Time the bus must be free before a new transmission can start(1) 1.2 μs tHD.STA Start Hold Time 0.6 μs tSU.STA Start Set-up Time 0.6 μs tHD.DAT Data In Hold Time 0 μs tSU.DAT Data In Set-up Time 100 ns tR (1) Inputs Rise Time 0.3 μs tF (1) Inputs Fall Time 300 ns tSU.STO Stop Set-up Time 0.6 μs tDH Data Out Hold Time 50 ns tWR Write Cycle Time 5 ms Endurance(1) 5.0V, 25C, Page Mode 1,000,000 Write Cycles

9AT24C64B Automotive [DATASHEET] Atmel-8778B-SEEPROM-AT24C64B-Auto-Datasheet_082014 7. Device Addressing The 64K EEPROM requires an 8-bit device address word following a Start condition to enable the device for a Read or Write operation. The device address word consists of a mandatory one, zero sequence for the first four most significant bits as shown. This is common to all 2-wire EEPROM devices. The 64K uses the three device address bits A2, A1, and A0 to allow as many as eight devices on the same bus. These bits must compare to their corresponding hardwired input pins. The A 2, A1, and A0 pins use an internal proprietary circuit that biases them to a logic low condition if the pins are allowed to float. The eighth bit of the device address is the Read/Write operation select bit. A Read operation is initiated if this bit is high, and a Write operation is initiated if this bit is low. Upon a compare of the device address, the EEPROM will output a zero. If a compare is not made, the device will return to standby state. Noise Protection: Special internal circuitry placed on the SDA and SCL pins prevent small noise spikes from activating the device. Data Security: The AT24C64B has a hardware data protection scheme that allows the user to write protect the upper quadrant of memory when the WP pin is at VCC. Figure 7-1. Device Address 6 4 K 1010 A 2 A 1 A 0 R / W MSB LSB

AT24C64B Automotive [DATASHEET] Atmel-8778B-SEEPROM-AT24C64B-Auto-Datasheet_082014 Sequential Read: Sequential Reads are initiated by either a Current Address Read or a Random Address Read. After the microcontroller receives a data word, it responds with an acknowledge. As long as the EEPROM receives an acknowledge, it will continue to increment the data word address and serially clock out sequential data words. When the memory address limit is reached, the data word address will roll-over and the Sequential Read will continue. The Sequential Read operation is terminated when the microcontroller does not respond with a zero but does generate a following Stop condition. Figure 9-3. Sequential Read 10. Power Recommendation The device internal POR (Power-On Reset) threshold is just below the minimum operating voltage of the device. Power shall rise monotonically from 0.0Vdc to full V CC in less than 1ms. Hold at full VCC for at least 100μs before the first operation. Power shall drop from full VCC to 0.0Vdc in less than 1ms. Power dropping to a non-zero level and then slowly going to zero is not recommended. Power shall remain off (0.0Vdc) for 0.5s minimum. Please consult Atmel if your power conditions do not meet the above recommendations. SDA Line Device Address R E A D A C K A C K A C K S T O P A C K R W N O A C K Data (n) Data (n + 1) Data (n + 2) Data (n + x)

13AT24C64B Automotive [DATASHEET] Atmel-8778B-SEEPROM-AT24C64B-Auto-Datasheet_082014 11. Ordering Code Detail AT24C64BN-10SQ-2 . 7 Atmel Designator Product Family Device Density Device Revision Operating Voltage Package Option Speed Type 64 = 64 kilobit (Package Type Dependant) N = 0.150” width SOIC 24C = 2-Wire Compatible Serial EEPROM M = 2.7V to 5.5V S = JEDEC SOIC T = TSSOP 10 = Default Value Note: This field is not used for Serial EEPROM products. Package Variation Package Device Grade Q = Lead-free/Halogen-free Automotive Temperature Range (-40°C to +125°C)

AT24C64B Automotive [DATASHEET] Atmel-8778B-SEEPROM-AT24C64B-Auto-Datasheet_082014 12. Product Markings DRAWING NO. REV. TITLE 24C64BAM C 6/12/14 24C64BAM, AT24C64B Automotive Package Marking Information Package Mark Contact: DL-CSO-Assy_eng@atmel.com SQ%% D24C64BN ATMELYWW 8-lead SOIC 8-lead TSSOP AT### Q% D Note 2: Package drawings are not to scale Note 1: designates pin 1 AT24C64B Automotive Package Marking Information Catalog Number Truncation AT24C64B Truncation Code ###: 64B Date Codes Voltages Y = Year M = Month WW = Work Week of Assembly % = Minimum Voltage 4: 2014 8: 2018 A: January 02: Week 2 3 or 27: 2.7V min 5: 2015 9: 2019 B: February 04: Week 4 7: 2017 1: 2021 L: December 52: Week 52 Country of Assembly Lot Number Grade/Lead Finish Material @ = Country of Assembly AAA...A = Atmel Wafer Lot Number Q: Automotive /Matte Tin/SnAgCu Trace Code Atmel Truncation XX = Trace Code (Atmel Lot Numbers Correspond to Code) AT: Atmel Example: AA, AB.... YZ, ZZ ATM: Atmel ATML: Atmel Note: Lot Number and location of assembly on the bottom side of the package. Note: Lot Number, location of assembly and YWW date code on the bottom side of the package.

15AT24C64B Automotive [DATASHEET] Atmel-8778B-SEEPROM-AT24C64B-Auto-Datasheet_082014 13. Ordering Information (1) Notes: 1. For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC characteristics tables. 2. “Q” designates green package and RoHS compliant. Atmel Ordering Code Lead Finish Package Voltage Operation Range AT24C64BN-10SQ-2.7(2) Matte Tin (Lead-free/Halogen-free) 8S1 2.7V to 5.5V Automotive Temperature (-40C to +125C)AT24C64B-10TQ-2.7(2) 8X Package Type 8S1 8-lead, 0.150" wide body, Plastic Gull Wing Small Outline (JEDEC SOIC) 8X 8-lead, 4.4mm body, Plastic Thin Shrink Small Outline Package (TSSOP)

AT24C64B Automotive [DATASHEET] Atmel-8778B-SEEPROM-AT24C64B-Auto-Datasheet_082014 14. Package Drawings 14.1 8S1 — 8-lead JEDEC SOIC DRAWING NO. REV. TITLE GPC COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 A 1.35 – 1.75 b 0.31 – 0.51 C 0.17 – 0.25 D 4.80 – 5.05 E1 3.81 – 3.99 E 5.79 – 6.20 e 1.27 BSC L 0.40 – 1.27 ØØ 0° – 8° Ø E N TOP VIEW C END VIEW A b L e D SIDE VIEW Package Drawing Contact: packagedrawings@atmel.com 8S1 G 6/22/11 Notes: This drawing is for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 8S1, 8-lead (0.150” Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) SWB

17AT24C64B Automotive [DATASHEET] Atmel-8778B-SEEPROM-AT24C64B-Auto-Datasheet_082014 14.2 8X — 8-lead TSSOP DRAWING NO. REV. TITLE GPC COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A - - 1.20 A1 0.05 - 0.15 A2 0.80 1.00 1.05 D 2.90 3.00 3.10 2, 5 E 6.40 BSC E1 4.30 4.40 4.50 3, 5 b 0.19 0.25 0.30 4 e 0.65 BSC L 0.45 0.60 0.75 L1 1.00 REF C 0.09 - 0.20 Side View End ViewTop View A L D N b Pin 1 indicator this corner E e Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15mm (0.006in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25mm (0.010in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07mm. 5. Dimension D and E1 to be determined at Datum Plane H. Package Drawing Contact: packagedrawings@atmel.com 8X E 2/27/14 8X, 8-lead 4.4mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) TNR C

AT24C64B Automotive [DATASHEET] Atmel-8778B-SEEPROM-AT24C64B-Auto-Datasheet_082014 15. Revision History Revision Date Comments 8778B 08/2014 Add the sections, power recommendation and ordering code detail. Updated part markings, template, logos, and disclaimer page. No changes to functional specification. 8778A 09/2011 Initial document release.

Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 | www.atmel.com © 2014 Atmel Corporation. / Rev.: Atmel-8778B-SEEPROM-AT24C64B-Auto-Datasheet_082014. Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®,and others are registered trademarks or trademarks of Atmel Corporation in U.S. and other countries. Other terms and product names may be trademarks of others. DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDIT IONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS P RODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMI TATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or c ompleteness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel d oes not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automo tive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical A pplications”) without an Atmel officer's specific written consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for t he operation of nuclear facilities and weapons systems. Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.