AT24C512_07 ATMEL
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 22
Technical content
Features
- Low-voltage and Standard-voltage Operation – 2.7 (V CC = 2.7V to 5.5V) – 1.8 (V CC = 1.8V to 3.6V)
- Internally Organized 65,536 x 8
- Two-wire Serial Interface
- Schmitt Triggers, Filtered Inputs for Noise Suppression
- Bidirectional Data Transfer Protocol
- 1 MHz (5V), 400 kHz (2.7V) and 100 kHz (1.8V) Compatibility
- Write Protect Pin for Hardware and Software Data Protection
- 128-byte Page Write Mode (Partial Page Writes Allowed)
- Self-timed Write Cycle (5 ms Max)
- High Reliability – Endurance: 100,000 Write Cycles – Data Retention: 40 Years
- Automotive Devices Available
- 8-lead PDIP , 8-lead EIAJ SOIC, 8-lead JEDEC SOIC, 8-lead TSSOP, 8-lead LAP, 8-lead SAP and 8-ball dBGA2 Packages
- Die Sales: Wafer Form, Waffle Pack and Bumped Die
Description
The AT24C512 provides 524,288 bits of serial electrically erasable and programmable read only memory (EEPROM) organized as 65,536 words of 8 bits each. The device’s cascadable feature allows up to four devices to share a common two-wire bus. The device is optimized for use in many industrial and commercial applications where low- power and low-voltage operation are essential. The devices are available in space- saving 8-pin PDIP, 8-lead EIAJ SOIC, 8- lead JEDEC SOIC, 8-lead TSSOP , 8-lead Leadless Array (LAP), and 8-lead SAP packages. In addition, the entire family is avail- Table 1. Pin Configurations
2 AT24C512
Figure 1. Block Diagram
1116O–SEEPR–1/07 Pin Description SERIAL CLOCK (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative edge clock data out of each device. SERIAL DATA (SDA): The SDA pin is bidirectional for serial data transfer. This pin is open-drain driven and may be wire-ORed with any number of other open-drain or open collector devices. DEVICE/ADDRESSES (A1, A0): The A1 and A0 pins are device address inputs that are hardwired or left not connect ed for hardware compatibility with other AT24Cxx devices. When the pins are hardwired, as many as four 512K devices may be addressed on a single bus system (device addressing is discussed in detail under the Device Address- ing section. If the pins are left floating, the A1 and A0 pins will be internally pulled down to GND if the capacitive coup ling to the circuit board V CC plane is <3 pF. If coupling is >3 pF, Atmel recommends connecting the address pins to GND. WRITE PROTECT (WP): The write protect input, when connected to GND, allows nor- mal write operations. When WP is connected high to V CC, all write operations to the memory are inhibited. If the pin is left floating, the WP pin will be internally pulled down to GND if the capacitive coup ling to the circuit board V CC plane is <3 pF. If coupling is >3 pF, Atmel recommends connecting the pin to GND. Switching WP to V CC prior to a write operation creates a software write protect function. Memory Organization AT24C512, 512K SERIAL EEPROM: The 512K is internally organized as 512 pages of 128-bytes each. Random word addressing requires a 16-bit data word address.
4 AT24C512
Note: 1. This parameter is characterized and is not 100% tested. Note: 1. V IL min and VIH max are reference only and are not tested. Table 2. Pin Capacitance(1) Table 3. DC Characteristics
Notes: 1. This parameter is characterized and is not 100% tested.
- AC measurement conditions:
- The Write Cycle Time of 5 ms only applies to the AT24C512 devices bearing the process letter “A” on the package (the mark
is located in the lower right corner on the top side of the package). Table 4. AC Characteristics erwise noted) Test conditions are listed in Note 2.
6 AT24C512
1116O–SEEPR–1/07 Device Operation CLOCK and DATA TRANSITIONS: The SDA pin is normally pulled high with an exter- nal device. Data on the SDA pin may change only during SCL low time periods (see Figure 4 on page 7). Data c hanges during SCL high periods will indicate a start or stop condition as defined below. START CONDITION: A high-to-low transition of SDA with SCL high is a start condition which must precede any other command (see Figure 5 on page 8). STOP CONDITION: A low-to-high transition of SDA wit h SCL high is a stop condition. After a read sequence, the stop command will place th e EEPROM in a standby power mode (see Figure 5 on page 8). ACKNOWLEDGE: All addresses and data words are serially transmitted to and from the EEPROM in 8-bit words. The EEPROM sends a zero during the ninth clock cycle to acknowledge that it has received each word. STANDBY MODE: The AT24C512 features a low power standby mode which is enabled: a) upon power-up and b) after the receipt of the STOP bit and the completion of any internal operations. MEMORY RESET: After an interruption in protocol, power loss or system reset, any two- wire part can be reset by following these steps: (a) Clock up to 9 cycles, (b) look for SDA hi gh in each cycle while SCL is high and then (c) create a start condition as SDA is high.
8 AT24C512
Figure 5. Start and Stop Definition Figure 6. Output Acknowledge
1116O–SEEPR–1/07 Device Addressing The 512K EEPROM requires an 8-bit device address word following a start condition to enable the chip for a read or write operation (see Figure 7 on page 10). The device address word consists of a mandatory “1”, “0” sequence for the first five most significant bits as shown. This is common to all two-wire EEPROM devices. The 512K uses the two device address bits A1 , A0 to allow as many as four devices on the same bus. These bits must compare to their corresponding hardwired input pins. The A1 and A0 pins use an internal propriet ary circuit that biases them to a logic low condition if the pins are allowed to float. The eighth bit of the device address is the r ead/write operation select bit. A read opera- tion is initiated if this bit is high and a write operation is initiated if this bit is low. Upon a compare of the device address, th e EEPROM will output a “0”. If a compare is not made, the device will return to a standby state. DATA SECURITY: The AT24C512 has a hardware data protection scheme that allows the user to Write Protect the whole memory when the WP pin is at V CC. Write Operations BYTE WRITE: A write operation requires two 8-bit data word addresses following the device address word and acknowledgment. Upon receipt of this address, the EEPROM will again respond with a “0” and then clock in the first 8-bit data word. Following receipt of the 8-bit data word, the EEPROM will output a “0”. The addressing device, such as a microcontroller, then must term inate the write sequence with a stop condition. At this time the EEPROM enters an internally-timed write cycle, t WR, to the nonvolatile memory. All inputs are disabled during this write cycle and the EEPROM will not respond until the write is complete (see Figure 8 on page 11). PAGE WRITE: The 512K EEPROM is capable of 128-byte page writes. A page write is initiated the same way as a byte write, but the microcontroller does not send a stop condition after the first data wo rd is clocked in. Instead, after the EEPROM acknowledges receipt of the fi rst data word, the microcontrol ler can transmit up to 127 more data words. The EEPROM will respond with a “0” after each data word received. The microcontroller must terminate the page write sequence with a stop condition (see Figure 9 on page 11). The data word address lower 7 bits are internally incremented following the receipt of each data word. The higher data word address bits are not incremented, retaining the memory page row location. When the word address, internally generated, reaches the page boundary, the following byte is placed at the beginning of the same page. If more than 128 data words are transmitted to the EEPROM, the data word address will “roll over” and previous data will be overwritten. The address roll over during write is from the last byte of the current page to the first byte of the same page. ACKNOWLEDGE POLLING: Once the internally-timed write cycle has started and the EEPROM inputs are disabled, acknowledge polling can be initiated. This involves send- ing a start condition followed by the dev ice address word. The Read/Write bit is representative of the operation desired. Only if the internal write cycle has completed will the EEPROM respond with a “0”, allowing the read or write sequence to continue.
10 AT24C512
operations: current address read, random address read and sequential read. acknowledged by the EEPROM, the current addr ess data word is serially clocked out. stop condition (see Figure 10 on page 11). with a “0” but does generate a following stop condition (see Figure 11 on page 11). Figure 7. Device Address
12 AT24C512
Figure 12. Sequential Read
1116O–SEEPR–1/07 Notes: 1. For 2.7V devices used in the 4.5V to 5.5V range, pleas e refer to performance values in the AC and DC characteristics tables. 2. “U” designates Green package + RoHS compliant. 3. Available in waffle pack and wafer form; order as SL788 for inkless wafer form. Bumped die available upon request. Please contact Serial EEPROM marketing. Ordering Information(1) Ordering Code Package Operation Range AT24C512C1-10CU-2.7(2) AT24C512C1-10CU-1.8(2) AT24C512-10PU-2.7(2) AT24C512-10PU-1.8(2) AT24C512W-10SU-2.7(2) AT24C512W-10SU-1.8(2) AT24C512N-10SU-2.7(2) AT24C512N-10SU-1.8(2) AT24C512-10TU-2.7(2) AT24C512-10TU-1.8(2) AT24C512Y4-10YU-1.8(2) AT24C512U4-10UU-1.8(2) 8CN1 8CN1 8P3 8P3 8S2 8S2 8S1 8S1 8A2 8A2 8Y4 8U4-1 Lead-free/Halogen-free/ Industrial Temperature (–40°C to 85°C) AT24C512-W1.8-11 (3) Die Sale Industrial Temperature (–40°C to 85°C) Package Type 8CN1 8-lead, 0.300" Wide, Leadless Array Package (LAP) 8P3 8-lead, 0.300" Wide, Plastic Dual In-line Package (PDIP) 8S2 8-lead, 0.200” Wide, Plastic Gull Wing Small Outline Package (EIAJ SOIC) 8S1 8-lead, 0.150” Wide, Plastic Gull Wing Small Outline Package (JEDEC SOIC) 8A2 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) 8Y4 8-lead, 6.00 mm x 4.90 mm Body, Dual Footprint, Non-leaded, Small Array Package (SAP) 8U4-1 8-ball, die Ball Grid Array Package (dBGA2) Options –2.7 Low-voltage (2.7V to 5.5V) –1.8 Low-voltage (1.8V to 3.6V)
14 AT24C512
1116O–SEEPR–1/07 Packaging Information 8U4-1 — dBGA2 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. PO8U4-1 A 1/5/05 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE 8U4-1, 8-ball, 2.47 x 4.07 mm Body, 0.75 mm pitch, Small Die Ball Grid Array Package (dBGA2) A 0.81 0.91 1.00 A1 0.15 0.20 0.25 A2 0.40 0.45 0.50 b 0.25 0.30 0.35 D 2.47 BSC E 4.07 BSC e 0.75 BSC e1 0.74 REF d 0.75 BSC d1 0.80 REF 5. Dimension 'b' is measured at the maximum solder ball diameter. This drawing is for general information only. d A SIDE VIEW TOP VIEW
8 SOLDER BALLS
A B C D (e1) e A1 BALL PAD CORNER (d1) 5. b DA1 BALL PAD CORNER E
1116O–SEEPR–1/07 8CN1 – LAP 1150 E.Cheyenne Mtn Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. 8CN1, 8-lead (8 x 5 x 1.04 mm Body), Lead Pitch 1.27 mm, Leadless Array Package (LAP) B8CN1 11/8/04 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A 0.94 1.04 1.14 A1 0.30 0.34 0.38 b 0.36 0.41 0.46 1 D 7.90 8.00 8.10 E 4.90 5.00 5.10 e 1.27 BSC e1 0.60 REF L 0.62 .0.67 0.72 1 L1 0.92 0.97 1.02 1 Note: 1. Metal Pad Dimensions. 2. All exposed metal area shall have the following finished platings. Ni: 0.0005 to 0.015 mm Au: 0.0005 to 0.001 mm Pin1 Corner Marked Pin1 Indentifier 0.10 mm TYP Top View L b e Side View A Bottom View E D
16 AT24C512
1116O–SEEPR–1/07 8P3 – PDIP
2325 Orchard Parkway
San Jose, CA 95131 TITLE DRAWING NO. R REV. 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) 01/09/02 8P3 B Notes: 1. This drawing is for general information only; refer to JEDEC Drawing M S-001, Variation BA, for additional information. 2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge G S-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion. COMMON DIMENSIONS (Unit of Measure = inches) SYMBOL MIN NOM MAX NOTE D E e Lb2 b A2 A N eA c
4 PLCS
A – – 0.210 2 A2 0.115 0.1 30 0.195 b 0.014 0.01 8 0.022 5 b2 0.045 0.060 0.070 6 b3 0.0 30 0.0 39 0.045 6 c 0.00 8 0.010 0.014 D 0. 355 0. 365 0.400 3 D1 0.005 – – 3 E 0. 300 0. 310 0. 325 4 E1 0.240 0.250 0.2 80 3 e 0.100 B SC eA 0. 300 BSC 4 L 0.115 0.1 30 0.150 2 Top View Side View End View
1116O–SEEPR–1/07 8S2 – EIAJ SOIC San Jose, CA 95131 TITLE DRAWING NO. R REV. 8S2, 8-lead, 0.209" Body, Plastic Small Outline Package (EIAJ) 10/7/03 8S2 C COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE Notes: 1. This drawing is for general information only; refer to EIAJ Drawing EDR-7320 for additional information. 2. Mismatch of the upper and lower dies and resin burrs are not included. 3. It is recommended that upper and lower cavities be equal. If they are different, the larger dimension shall be regarded. 4. Determines the true geometric position. A 1.70 2.16 A1 0.05 0.25 b 0. 35 0.4 8 5 C 0.15 0. 35 5 D 5.1 3 5. 35 E1 5.1 8 5.40 2, 3 E 7.70 8.26 L 0.51 0. 85 ∅ 0° 8° e 1.27 B SC 4 End View Side View e b A D E N C L Top View
18 AT24C512
1116O–SEEPR–1/07 8S1 – JEDEC SOIC 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. Note: 10/7/03 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) 8S1 B COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. A 1. 35 – 1.75 B 0. 31 – 0.51 C 0.17 – 0.25 D 4. 80 – 5.00 E1 3.81 – 3.99 E 5.79 – 6.20 e 1.27 B SC L 0.40 – 1.27 ∅ 0° – 8° Top View End View Side View e B D A N E C L
1116O–SEEPR–1/07 8A2 – TSSOP San Jose, CA 95131 TITLE DRAWING NO. R REV. 5/30/02 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 2.90 3.00 3.10 2, 5 E 6.40 BSC E1 4.30 4.40 4.50 3, 5 A – – 1.20 A2 0.80 1.00 1.05 b 0.19 – 0.30 4 e 0.65 BSC L 0.45 0.60 0.75 L1 1.00 REF 8A2, 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Notes: 1. Thi s drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimen sion D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimen sion E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimen sion b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimen sion D and E1 to be determined at Datum Plane H. 8A2 B Side View End ViewTop View A L D 123 N b Pin 1 indicator this corner E e
20 AT24C512
1116O–SEEPR–1/07 8Y4 – SAP 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80817 TITLE DRAWING NO. R REV. 8Y4, 8-lead (6.00 x 4.90 mm Body) SOIC Array Package (SAP) Y4 A8Y4 5/24/04 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A – – 0.90 A1 0.00 – 0.05 D 5. 80 6.00 6.20 E 4.70 4.90 5.10 D1 2. 85 3.00 3.15 E1 2. 85 3.00 3.15 b 0. 35 0.40 0.45 e 1.27 TYP e1 3.81 REF L 0.50 0.60 0.70 A E A1 b PIN 1 INDEX AREA D A PIN 1 ID L e
1116O–SEEPR–1/07
Revision History
Doc. Rev. Date Comments 1116O 1/2007 Revision history implemented. Added Note to Page 1 recommending new device.
Printed on recycled paper. 1116O–SEEPR–1/07 Disclaimer: The information in this document is provided in connection with Atmel products. No license, expr ess or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LI ABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTOR Y WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO , THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICU LAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR I NCIDEN- TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTE RRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or comp leteness of the contents of th is document and reserves the rig ht to make changes to specifications and product descriptions at any time withou t notice. Atmel does not make any commitm ent to update the information contained her ein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not int ended, authorized, or warranted for use as components in applications intended to support or sustain life. Atmel Corporation Atmel Operations San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza
77 Mody Road Tsimshatsui
Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Memory San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 Microcontrollers San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602
44306 Nantes Cedex 3, France
13106 Rousset Cedex, France
1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 RF/Automotive Theresienstrasse 2 Postfach 3535
74025 Heilbronn, Germany
1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123
38521 Saint-Egreve Cedex, France
www.atmel.com/literature © 2007 Atmel Corporation. All rights reserved. Atmel ®, logo and combinations t hereof, Everywhere You Are ® and others, are registered trade- marks or trademarks of Atmel Corporation or its subsidiaries . Other terms and product names may be trademarks of others.