AT24C512B_08 ATMEL
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 26
Technical content
Features
- Low-voltage and Standard-voltage Operation – 1.8v (V CC = 1.8V to 3.6V) – 2.5v (V CC = 2.5V to 5.5V) Internally Organized 65,536 x 8 Two-wire Serial Interface Schmitt Triggers, Filtered Inputs for Noise Suppression Bidirectional Data Transfer Protocol 1 MHz (2.5V, 5.5V), 400 kHz (1.8V) Compatibility Write Protect Pin for Hardware and Software Data Protection 128-byte Page Write Mode (Partial Page Writes Allowed) Self-timed Write Cycle (5 ms Max) High Reliability – Endurance: 1,000,000 Write Cycles – Data Retention: 40 Years Lead-free/Halogen-free Devices 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead EIAJ SOIC, 8-lead TSSOP, 8-ball dBGA2, and 8-lead Ultra Thin Small Array (SAP) Packages Die Sales: Wafer Form, Waffle Pack and Bumped Die
Description
The AT24C512B provides 524,288 bits of serial electrically erasable and programma- ble read only memory (EEPR OM) organized as 65,536 wo rds of 8 bits each. The device’s cascadable feature allo ws up to eight devices to share a common two-wire bus. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. The devices are available in space-saving 8-pin PDIP, 8-lead JEDEC SOIC, 8-lead EIAJ SOIC, 8-lead TSSOP, 8-ball dBGA2 and 8-lead Ultra Thin SAP packages. In addition, the entire family is Table 0-1. Pin Configurations Pin Name Function A0–A2 Address Inputs SDA Serial Data SCL Serial Clock Input WP Write Protect Rev. 5297A–SEEPR–1/08 Two-wire Serial EEPROM 512K (65,536 x 8) AT24C512B with Three Device Address Inputs 8-lead PDIP GND VCC WP SCL SDA 8-lead TSSOP GND VCC WP SCL SDA 8-lead Ultra Thin SAP Bottom View VCC WP SCL SDA GND 8-lead SOIC GND VCC WP SCL SDA 8-ball dBGA2 Bottom View VCC WP SCL SDA GND
5297A–SEEPR–1/08 AT24C512B Figure 0-1. Block Diagram Absolute Maximum Ratings* Maximum Ratings” may cause permanent dam- age to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Voltage on Any Pin START STOP LOGIC VCC GND WP SCL SDA SERIAL CONTROL LOGIC EN H.V. PUMP/TIMING EEPROM DATA RECOVERY SERIAL MUX X DEC DOUT/ACK LOGIC COMP LOAD INC DATA WORD ADDR/COUNTER Y DEC R/W DOUT DIN LOAD DEVICE ADDRESS COMPARATOR
5297A–SEEPR–1/08 AT24C512B 1. Pin Description SERIAL CLOCK (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative edge clock data out of each device. SERIAL DATA (SDA): The SDA pin is bidirectional for seri al data transfer. This pin is open- drain driven and may be wire-ORed with any number of other open-drain or open collector devices. DEVICE/PAGE ADDRESSES (A2, A1, A0): The A2, A1, and A0 pins are device address inputs that are hardwired (directly to GND or to Vcc) for compatibility with other AT24Cxx devices. When the pins are hardwired, as many as eight 512K devices may be addressed on a single bus system. (Device addressing is discussed in detail under “Device Addressing,” page 8.) A device is selected when a corresponding hardware and software match is true. If these pins are left floating, the A2, A1, and A0 pins will be interna lly pulled down to GND. However, due to capaci- tive coupling that may appear during customer applications, Atmel ® recommends always connecting the address pins to a known state. When using a pull-up resistor, Atmel recommends using 10kΩ or less. WRITE PROTECT (WP): The write protect input, when connected to GND, allows normal write operations. When WP is connected directly to Vcc, all write operations to the memory are inhib- ited. If the pin is left floating, the WP pin will be internal ly pulled down to GND. However, due to capacitive coupling that may appear during cu stomer applications, Atmel recommends always connecting the WP pins to a known state. When using a pull-up resistor, Atmel recommends using 10kΩ or less.
5297A–SEEPR–1/08 AT24C512B 2. Memory Organization AT24C512B, 512K SERIAL EEPROM: The 512K is internally organized as 512 pages of 128-bytes each. Random word addressing requires a 16-bit data word address. Note: 1. This parameter is characterized and is not 100% tested. Note: 1. V IL min and VIH max are reference only and are not tested. Table 2-1. Pin Capacitance(1) Applicable over recommended operating range from: TA = 25°C, f = 1.0 MHz, VCC = +1.8V to +5.5V Symbol Test Condition Max Units Conditions CI/O Input/Output Capacitance (SDA) 8 pF V I/O = 0V CIN Input Capacitance (A0, A1, SCL) 6 pF V IN = 0V Table 2-2. DC Characteristics Applicable over recommended operating range from: TAI = –40°C to +85°C, VCC = +1.8V to +5.5V (unless otherwise noted) Symbol Parameter Test Co ndition Min Typ Max Units VCC1 Supply Voltage 1.8 3.6 V VCC2 Supply Voltage 2.5 5.5 V ICC Supply Current V CC = 5.0V READ at 400 kHz 2.0 mA ICC Supply Current V CC = 5.0V WRITE at 400 kHz 3.0 mA ISB1 Standby Current VCC = 1.8V VIN = VCC or VSS 1.0 µA VCC = 3.6V 3.0 µA ISB2 Standby Current VCC = 2.5V VIN = VCC or VSS 2.0 µA VCC = 5.5V 6.0 µA ILI Input Leakage Current V IN = VCC or VSS 0.10 3.0 µA ILO Output Leakage Current VOUT = VCC or VSS 0.05 3.0 µA VIL Input Low Level(1) –0.6 V CC x 0.3 V VIH Input High Level(1) VCC x 0.7 V CC + 0.5 V VOL1 Output Low Level V CC = 1.8V I OL = 0.15 mA 0.2 V VOL2 Output Low Level V CC = 3.0V I OL = 2.1 mA 0.4 V
5297A–SEEPR–1/08 AT24C512B Notes: 1. This parameter is ensured by characterization only. 2. AC measurement conditions: RL (connects to VCC): 1.3 kΩ (2.5V, 5V), 10 kΩ (1.8V) Input pulse voltages: 0.3 VCC to 0.7 VCC Input rise and fall times: ≤ 50 ns Input and output timing reference voltages: 0.5 VCC Table 2-3. AC Characteristics (Industrial Temperature) Applicable over recommended operating range from TAI = −40°C to +85°C, VCC = +1.8V to +5.5V, CL = 100 pF (unless oth- erwise noted). Test conditions are listed in Note 2. Symbol Parameter 1.8-volt 2.5, 5.0-volt UnitsMin Max Min Max fSCL Clock Frequency, SCL 400 1000 kHz tLOW Clock Pulse Width Low 1.3 0.4 µs tHIGH Clock Pulse Width High 0.6 0.4 µs ti Noise Suppression Time(1) 100 50 ns tAA Clock Low to Data Out Valid 0.05 0.9 0.05 0.55 µs tBUF Time the bus must be free before a new transmission can start(1) 1.3 0.5 µs tHD.STA Start Hold Time 0.6 0.25 µs tSU.STA Start Set-up Time 0.6 0.25 µs tHD.DAT Data In Hold Time 0 0 µs tSU.DAT Data In Set-up Time 100 100 ns tR Inputs Rise Time(1) 0.3 0.3 µs tF Inputs Fall Time(1) 300 100 ns tSU.STO Stop Set-up Time 0.6 0.25 µs tDH Data Out Hold Time 50 50 ns tWR Write Cycle Time 5 5 ms Endurance(1) 25°C, Page Mode, 3.3V 1,000,000 Write Cycles
5297A–SEEPR–1/08 AT24C512B 3. Device Operation CLOCK and DATA TRANSITIONS: The SDA pin is normally pulled high with an external device. Data on the SDA pin may change only during SCL low time periods (see Figure 3-4 on page 8). Data changes during SCL high periods will indicate a start or stop condition as defined below. START CONDITION: A high-to-low transition of SDA with SCL high is a start condition which must precede any other command (see Figure 3-5 on page 8). STOP CONDITION: A low-to-high transition of SDA with SCL high is a stop condition. After a read sequence, the stop command will place the EEPROM in a standby power mode (see Fig- ure 3-5 on page 8). ACKNOWLEDGE: All addresses and data words are serially transmitted to and from the EEPROM in 8-bit words. The EEPROM sends a zero during the ninth clock cycle to acknowl- edge that it has received each word. STANDBY MODE: The AT24C512B features a low power standby mode which is enabled: a) upon power-up and b) after the receipt of the STOP bit and the completion of any internal operations. Software Reset: After an interruption in protocol, power loss or system reset, any 2-wire part can be protocol reset by following these steps: (a) Create a start bit condition, (b) clock 9 cycles, (c) create another start bit followed by stop bit condition as shown below. The device is ready for next communication after above steps have been completed. Figure 3-1. Protocol Reset Condition Start bit Stop bitStart bitDummy Clock Cycles SCL SDA 12 38 9
5297A–SEEPR–1/08 AT24C512B 4. Device Addressing The 512K EEPROM requires an 8-bi t device address word following a start condition to enable the chip for a read or write operation (see Figure 6-1 on page 10). The device address word con- sists of a mandatory “1”, “0” sequence for the firs t four most significant bits as shown. This is common to all two-wire EEPROM devices. The 512K uses the three device address bits A2, A1, A0 to allow as many as eight devices on the same bus. These bits must compare to their corresponding hardwired input pins. The A2, A1 and A0 pins use an internal proprietary circuit that biases them to a logic low condition if the pins are allowed to float. The eighth bit of the device address is the read/write operation select bit. A read operation is ini- tiated if this bit is high and a write operation is initiated if this bit is low. Upon a compare of the device address, the EEPROM will output a “0”. If a compare is not made, the device will return to a standby state. DATA SECURITY: The AT24C512B has a hardware data protection scheme that allows the user to Write Protect the whole memory when the WP pin is at V CC. 5. Write Operations BYTE WRITE: A write operation requires two 8-bit data word addresses following the device address word and acknowledgment. Upon receipt of this address, the EEPROM will again respond with a “0” and then clock in the first 8-bit data word. Following receipt of the 8-bit data word, the EEPROM will output a “0”. The addre ssing device, such as a microcontroller, then must terminate the writ e sequence with a stop condition. At this time the EEPROM enters an internally-timed write cycle, t WR, to the nonvolatile memory. All inputs are disabled during this write cycle and the EEPROM will not respond until the write is complete (see Figure 6-2 on page 10). PAGE WRITE: The 512K EEPROM is capable of 128-byte page writes. A page write is initiated the same way as a byte write, but the microcontroller does not send a stop condition after the first data word is cl ocked in. Instead, after the EEPROM acknowledges receipt of the first data word, the microcontroller can transmit up to 127 more data words. The EEPROM will respond with a “0” after each data word received. The microcontroller must termi- nate the page write sequence with a stop condition (see Figure 6-3 on page 11). The data word address lower 7 bits are internally incremented following the receipt of each data word. The higher data word address bits are not incremented, retaining the memory page row location. When the word address, internally generated, reaches the page boundary, the follow- ing byte is placed at the beginning of the same page. If more than 128 data words are transmitted to the EEPROM, the data word a ddress will “roll over” and previous data will be overwritten. The address roll over during write is from the last byte of the current page to the first byte of the same page. ACKNOWLEDGE POLLING: Once the internally-timed write cycle has started and the EEPROM inputs are disabled, ackno wledge polling can be initiate d. This involves sending a start condition followed by the device address word . The Read/Write bit is representative of the operation desired. Only if th e internal write cycle has comp leted will the EEPROM respond with a “0”, allowing the read or write sequence to continue.
5297A–SEEPR–1/08 AT24C512B Notes: 1. “-B” denotes bulk 3. Available in tape and reel, and wafer form; order as SL788 for inkless wafer form. Bumped die available upon request. Please contact Serial Interface Marketing.
Ordering Information
Ordering Code Voltage Package Operation Range AT24C512B-PU (Bulk form only) 1.8 8P3 Lead-free/Halogen-free/ Industrial Temperature (–40°C to 85°C) AT24C512B-PU25 (Bulk form only) 2.5 8P3 AT24C512BN-SH-B(1) (NiPdAu Lead Finish) 1.8 8S1 AT24C512BN-SH-T(2) (NiPdAu Lead Finish) 1.8 8S1 AT24C512BN-SH25-B(1) (NiPdAu Lead Finish) 2.5 8S1 AT24C512BN-SH25-T(2) (NiPdAu Lead Finish) 2.5 8S1 AT24C512BW-SH-B(1) (NiPdAu Lead Finish) 1.8 8S2 AT24C512BW-SH-T(2) (NiPdAu Lead Finish) 1.8 8S2 AT24C512BW-SH25-B(1) (NiPdAu Lead Finish) 2.5 8S2 AT24C512BW-SH25-T(2) (NiPdAu Lead Finish) 2.5 8S2 AT24C512B-TH-B(1) (NiPdAu Lead Finish) 1.8 8A2 AT24C512B-TH-T(2) (NiPdAu Lead Finish) 1.8 8A2 AT24C512B-TH25-B(1) (NiPdAu Lead Finish) 2.5 8A2 AT24C512B-TH25-T(2) (NiPdAu Lead Finish) 2.5 8A2 AT24C512BY7-YH-T(2) (NiPdAu Lead Finish) 1.8 8Y7 AT24C512BY7-YH25-T(2) (NiPdAu Lead Finish) 2.5 8Y7 AT24C512BU2-UU-T(2) 1.8 8U2-1 AT24C512B-W-11(3) 1.8 Die Sale Industrial Temperature (–40°C to 85°C) Package Type 8P3 8-lead, 0.300" Wide, Plastic Dual In-line Package (PDIP) 8S1 8-lead, 0.150” Wide, Plastic Gull Wing Small Outline Package (JEDEC SOIC) 8S2 8-lead, 0.200” Wide Plastic Gull Wing Small Outline Package (EIAJ SOIC) 8A2 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) 8Y7 8-lead, 6.00 mm x 4.90 mm Body, Ultra Thin, Dual Footprint, Non-leaded, Small Array Package (SAP) 8U2-1 8-ball, die Ball Grid Array Package (dBGA2) Options –1.8 Low-voltage (1.8V to 3.6V) –2.5 Low-voltage (2.5V to 5.5V)
5297A–SEEPR–1/08 AT24C512B 7. Part marking scheme: 7.1 8-PDIP(1.8V) 7.2 8-PDIP(2.5V) TOP MARK Seal Year Y = SEAL YEAR WW = SEAL WEEK | Seal Week 6: 2006 0: 2010 02 = Week 2 | | | 7: 2007 1: 2011 04 = Week 4 A T M L U Y W W 9: 2009 3: 2013 :: : :::: ::
2 F B 1 52 = Week 52
- Lot Number Lot Number to Use ALL Characters in Marking | BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark TOP MARK Seal Year Y = SEAL YEAR WW = SEAL WEEK | Seal Week 6: 2006 0: 2010 02 = Week 2 | | | 7: 2007 1: 2011 04 = Week 4 A T M L U Y W W 9: 2009 3: 2013 :: : :::: ::
2 F B 2 52 = Week 52
- Lot Number Lot Number to Use ALL Characters in Marking | BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark
5297A–SEEPR–1/08 AT24C512B 7.3 8-SOIC(1.8V) 7.4 8-SOIC(2.5V) TOP MARK Seal Year Y = SEAL YEAR WW = SEAL WEEK | Seal Week 6: 2006 0: 2010 02 = Week 2 | | | 7: 2007 1: 2011 04 = Week 4 A T M L H Y W W 9: 2009 3: 2013 :: : :::: ::
- Lot Number Lot Number to Use ALL Characters in Marking | BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark TOP MARK Seal Year Y = SEAL YEAR WW = SEAL WEEK | Seal Week 6: 2006 0: 2010 02 = Week 2 | | | 7: 2007 1: 2011 04 = Week 4 A T M L H Y W W 9: 2009 3: 2013 :: : :::: ::
- Lot Number Lot Number to Use ALL Characters in Marking | BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark
5297A–SEEPR–1/08 AT24C512B 7.5 8-TSSOP(1.8V) 7.6 8-TSSOP(2.5V) TOP MARK Pin 1 Indicator (Dot) Y = SEAL YEAR WW = SEAL WEEK | 6: 2006 0: 2010 02 = Week 2
2 F B 1 * 50 = Week 50
|---|---|---|---|---|---|---| Country of origin C 0 0 A A A A A A A <- Pin 1 Indicator TOP MARK Pin 1 Indicator (Dot) Y = SEAL YEAR WW = SEAL WEEK | 6: 2006 0: 2010 02 = Week 2
2 F B 2 * 50 = Week 50
<- Pin 1 Indicator
5297A–SEEPR–1/08 AT24C512B 7.7 8-Ultra Thin SAP (1.8V) 7.8 8-Ultra Thin SAP (2.5V) TOP MARK Seal Year | Seal Week Y = SEAL YEAR WW = SEAL WEEK | | | 6: 2006 0: 2010 02 = Week 2 A T M L H Y W W 8: 2008 2: 2012 :: : :::: :
2 F B 1 50 = Week 50
Pin 1 Indicator (Dot) TOP MARK Seal Year | Seal Week Y = SEAL YEAR WW = SEAL WEEK | | | 6: 2006 0: 2010 02 = Week 2 A T M L H Y W W 8: 2008 2: 2012 :: : :::: :
2 F B 2 50 = Week 50
Pin 1 Indicator (Dot)
5297A–SEEPR–1/08 AT24C512B 7.8 dBGA2 TOP MARK |<-- Pin 1 This Corner P = Country of Origin Y = ONE DIGIT YEAR CODE 4: 2004 7: 2007 5: 2005 8: 2008 6: 2006 9: 2009 M = SEAL MONTH (USE ALPHA DESIGNATOR A-L) A = JANUARY B = FEBRUARY J = OCTOBER K = NOVEMBER L = DECEMBER TC = TRACE CODE (ATMEL LOT NUMBERS TO CORRESPOND WITH ATK TRACE CODE LOG BOOK)
5297A–SEEPR–1/08 AT24C512B 8. Package Information U2-1 - dBGA2 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. PO8U2-1 A 6/17/03 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE 8U2-1, 8-ball, 2.35 x 3.73 mm Body, 0.75 mm pitch, Small Die Ball Grid Array Package (dBGA2) A 0.81 0.91 1.00 A1 0.15 0.20 0.25 A2 0.40 0.45 0.50 b 0.25 0.30 0.35 D 2.35 BSC E 3.73 BSC e 0.75 BSC e1 0.74 REF d 0.75 BSC d1 0.80 REF 5. Dimension 'b' is measured at the maximum solder ball diameter. This drawing is for general information only. d A SIDE VIEW TOP VIEW
8 SOLDER BALLS
A B C D (e1) e A1 BALL PAD CORNER (d1) 5. b DA1 BALL PAD CORNER E
5297A–SEEPR–1/08 AT24C512B 8P3 – PDIP
2325 Orchard Parkway
San Jose, CA 95131 TITLE DRAWING NO. R REV. 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) 01/09/02 8P3 B Notes: 1. Thi s drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA, for additional information. 2. Dimen sions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or ro unded lead tips are preferred to ease insertion. COMMON DIMENSIONS (Unit of Measure = inches) SYMBOL MIN NOM MAX NOTE D E e Lb2 b A2 A N eA c
4 PLCS
A – – 0.210 2 A2 0.115 0.1 30 0.195 b 0.014 0.01 8 0.022 5 b2 0.045 0.060 0.070 6 b3 0.0 30 0.0 39 0.045 6 c 0.00 8 0.010 0.014 D 0. 355 0. 365 0.400 3 D1 0.005 – – 3 E 0. 300 0. 310 0. 325 4 E1 0.240 0.250 0.2 80 3 e 0.100 B SC eA 0. 300 BSC 4 L 0.115 0.1 30 0.150 2 Top View Side View End View
5297A–SEEPR–1/08 AT24C512B 8S1 – JEDEC SOIC 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. Note: 10/7/03 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) 8S1 B COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. A 1. 35 – 1.75 B 0. 31 – 0.51 C 0.17 – 0.25 D 4. 80 – 5.00 E1 3.81 – 3.99 E 5.79 – 6.20 e 1.27 B SC L 0.40 – 1.27 ∅ 0° – 8° Top View End View Side View e B D A N E C L
5297A–SEEPR–1/08 AT24C512B 8S2 - EIAJ SOIC San Jose, CA 95131 TITLE DRAWING NO. R REV. 8S2, 8-lead, 0.209" Body, Plastic Small Outline Package (EIAJ) 4/7/06 8S2 D COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE Notes: 1. This drawing is for general information only; refer to EIAJ Drawing EDR-7320 for additional information. 2. Mismatch of the upper and lower dies and resin burrs aren't included. 3. It is recommended that upper and lower cavities be equal. If they are different, the larger dimension shall be regarded. 4. Determines the true geometric position. A 1.70 2.16 A1 0.05 0.25 b 0.35 0.48 5 C 0.15 0.35 5 D 5.13 5.35 E1 5.18 5.40 2, 3 E 7.70 8.26 L 0.51 0.85 θ 0˚ 8˚ e 1.27 BSC 4 θθ NN EE TOP VIEWTOP VIEW CC E1E1 END VIEWEND VIEW AA bb LL A1A1 ee DD SIDE VIEWSIDE VIEW
5297A–SEEPR–1/08 AT24C512B 8A2 – TSSOP San Jose, CA 95131 TITLE DRAWING NO. R REV. 5/30/02 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 2.90 3.00 3.10 2, 5 E 6.40 BSC E1 4.30 4.40 4.50 3, 5 A – – 1.20 A2 0.80 1.00 1.05 b 0.19 – 0.30 4 e 0.65 BSC L 0.45 0.60 0.75 L1 1.00 REF 8A2, 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimension D and E1 to be determined at Datum Plane H. 8A2 B Side View End ViewTop View A L D 123 N b Pin 1 indicator this corner E e
5297A–SEEPR–1/08 AT24C512B 8Y7 – UTSAP 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. 8Y7, 8-lead (6.00 x 4.90 mm Body) Ultra-Thin SOIC Array Package (UTSAP) Y7 B8Y7 10/13/05 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A – – 0.60 A1 0.00 – 0.05 D 5.80 6.00 6.20 E 4.70 4.90 5.10 D1 3.30 3.40 3.50 E1 3.90 4.00 4.10 b 0.35 0.40 0.45 e 1.27 TYP e1 3.81 REF L 0.50 0.60 0.70 PIN 1 ID L b e PIN 1 INDEX AREA A E D A
5297A–SEEPR–1/08 AT24C512B 8U2-1 – dBGA2 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. PO8U2-1 A 6/17/03 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE 8U2-1, 8-ball, 2.35 x 3.73 mm Body, 0.75 mm pitch, Small Die Ball Grid Array Package (dBGA2) A 0.81 0.91 1.00 A1 0.15 0.20 0.25 A2 0.40 0.45 0.50 b 0.25 0.30 0.35 D 2.35 BSC E 3.73 BSC e 0.75 BSC e1 0.74 REF d 0.75 BSC d1 0.80 REF 5. Dimension 'b' is measured at the maximum solder ball diameter. This drawing is for general information only. d A SIDE VIEW TOP VIEW A B C D (e1) e A1 BALL PAD CORNER (d1) 5. b DA1 BALL PAD CORNER E
5297A–SEEPR–1/08 AT24C512B
Revision History
Doc. Rev. Date Comments 5297A 1/2008 AT24C512B product with date code 2008 work week 14 (814) or later supports 5Vcc operation Initial document release
5297A–SEEPR–1/08 Headquarters International Atmel Corporation San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Room 1219 Chinachem Golden Plaza
77 Mody Road Tsimshatsui
Tel: (852) 2721-9778 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309
78054 Saint-Quentin-en-
9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Product Contact Web Site www.atmel.com Technical Support s_eeprom@atmel.com Sales Contact www.atmel.com/contacts Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL ’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL ’S WEB SITE, ATMEL ASSUMES NO LI ABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTOR Y WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICU LAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR I NCIDEN- TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATME L HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or comp leteness of the contents of this document and reserves the rig ht to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained her ein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not int ended, authorized, or warranted for use as components in applications in tended to support or sustain life. ©2008 Atmel Corporation. All rights reserved. Atmel ®, logo and combinations thereof, and others, are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other te rms and product names may be trademarks of others.