DATASHEET SEARCH SITE

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 24

Technical content

Features

 Low-voltage and standard-voltage operation  VCC = 1.7V to 5.5V  Internally organized as 4,096 x 8 (32K)  I2C-compatible (2-Wire) serial interface  Schmitt Trigger, filtered inputs for noise suppression  Bidirectional data transfer protocol  400kHz (1.7V) and 1MHz (2.5V, 2.7V, 5.0V) compatibility  Write Protect pin for hardware protection  32-byte Page Write mode  Partial Page Writes allowed  Self-timed Write cycle (5ms max)  High reliability  Endurance: 1,000,000 write cycles  Data retention: 100 years  Lead-free/Halogen-free devices available  Green package options (Pb/Halide-free/RoHS compliant)  8-lead JEDEC SOIC, 8-lead TSSOP, 8-pad UDFN, 8-pad XDFN, 5-lead SOT23, 5-ball WLCSP, and 8-ball VFBGA packages  Die sale options: wafer form, waffle pack, and bumped wafers

Description

The Atmel® AT24C32D provides 32,768 bits of Serial Electrically Erasable and Programmable Read-Only Memory (EEPROM) organized as 4,096 words of eight bits each. The device’s cascading feature allows up to eight devices to share a common 2-wire bus. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. The devices are available in space-saving 8-lead JEDEC SOIC, 8-lead TSSOP, 8-pad UDFN, 8-pad XDFN, 5-lead SOT23, 5-ball WLCSP, and 8-ball VFBGA packages. In addition, this device operates from 1.7V to 5.5V. AT24C32D I2C-Compatible (2-Wire) Serial EEPROM 32-Kbit (4,096 x 8) DATASHEET

AT24C32D [DATASHEET] Atmel-8866A-SEEPROM-AT24C32D-Datasheet_082013 1. Pin Configurations and Pinouts Table 1-1. Pin Configuration Note: When using the 5-lead SOT-23 or the 5-ball WLCSP, the software bits A2, A1, and A0 must be set to Logic 0 to properly communicate with the device. 2. Absolute Maximum Ratings* Pin Function A0 Address Input A1 Address Input A2 Address Input GND Ground SDA Serial Data SCL Serial Clock Input WP Write Protect VCC Device Power Supply 8-pad UDFN/XDFN VCC WP SCL SDA GND 8-ball VFBGA Bottom View 8-lead SOIC 8-lead TSSOP Top View GND VCC WP SCL SD A Top View Top View GND VCC WP SCL SDA SCL GND SDA 5-lead SOT23 WP VCC * Note: Drawings are not to scale 5-ball WLCSP Ball Side View GND SCL WP SDA VCC (1) GND VCC WP SCL SDA (1) Voltage on any pin *Notice: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification are not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

3AT24C32D [DATASHEET] Atmel-8866A-SEEPROM-AT24C32D-Datasheet_082013 3. Block Diagram 4. Pin Descriptions Serial Clock (SCL): The SCL input is used to positive-edge clock data into each EEPROM device and negative-edge clock data out of each device. Serial Data (SDA): The SDA pin is bidirectional for serial data transfer. This pin is open drain driven and may be wire-ORed with any number of other open-drain or open-collector devices. Device Addresses (A2, A1, A0): The A2, A1, and A0 pins are device address inputs that are hard wired (directly to GND or to VCC) for compatibility with other Atmel AT24C devices. When the pins are hard wired, as many as eight 32K devices may be addressed on a single bus system. (Device addressing is discussed in detail in Section 7., “Device Addressing” on page 9). A device is selected when a corresponding hardware and software match is true. If these pins are left floating, the A2, A1, and A0 pins will be internally pulled down to GND. However, due to capacitive coupling that may appear during customer applications, Atmel recommends always connecting the address pins to a known state. When using a pull-up resistor, Atmel recommends using 10k or less. Write Protect (WP): The Write Protect input, when connected to GND, allows normal write operations. When WP is connected directly to V CC, all Write operations to the memory are inhibited. If the pin is left floating, the WP pin will be internally pulled down to GND; however, due to capacitive coupling that may appear during customer applications, Atmel recommends always connecting the WP pins to a known state. When using a pull-up resistor, Atmel recommends using 10k or less. Table 4-1. Write Protect VCC GND WP SCL SDA EN EEPROM XD EC DOUT/ACK LOGIC COMP LOAD INC Y DEC R/W DOUT DIN LOAD Start Stop Logic Serial Control Logic H.V. Pump/Timing Device Address Comparator Data Word Addr/Counter Data Recovery Serial MUX WP Pin Status Part of the Array Protected At VCC Full Array At GND Normal Read/Write Operations

AT24C32D [DATASHEET] Atmel-8866A-SEEPROM-AT24C32D-Datasheet_082013 5. Memory Organization AT24C32D, 32K Serial EEPROM: The 32K is internally organized as 128 pages of 32-bytes each. Random word addressing requires a 12-bit data word address. Table 5-1. Pin Capacitance (1) Note: 1. This parameter is characterized and is not 100% tested. Table 5-2. DC Characteristics Note: 1. V IL min and VIH max are reference only and are not tested. Applicable over recommended operating range from: TA = 25°C, f = 1.0MHz, VCC = 5.5V Symbol Test Condition Max Units Conditions CI/O Input/Output Capacitance (SDA) 8 pF VI/O = 0V CIN Input Capacitance (A0, A1, A2, and SCL) 6 pF VIN = 0V Applicable over recommended operating range from: TAI = -40°C to +85°C, VCC = 1.7V to 5.5V (unless otherwise noted). Symbol Parameter Test Condition Min Typ Max Units VCC1 Supply Voltage 1.7 5.5 V ICC1 Supply Current VCC = 5.0V Read at 400kHz 0.4 1.0 mA ICC2 Supply Current VCC = 5.0V Write at 400kHz 2.0 3.0 mA ISB1 Standby Current VCC = 1.7V VIN = VCC or VSS 1.0 μA VCC = 5.0V 6.0 μA ILI Input Leakage Current VCC = 5.0V VIN = VCC or VSS 0.10 3.0 μA ILO Output Leakage Current VCC = 5.0V VOUT = VCC or VSS 0.05 3.0 μA VIL Input Low Level(1) -0.6 VCC x 0.3 V VIH Input High Level((1) VCC x 0.7 VCC + 0.5 V VOL1 Output Low Level VCC = 1.7V IOL = 0.15mA 0.2 V VOL2 Output Low Level VCC = 3.0V IOL = 2.1mA 0.4 V

5AT24C32D [DATASHEET] Atmel-8866A-SEEPROM-AT24C32D-Datasheet_082013 Table 5-3. AC Characteristics (Industrial Temperature) Notes: 1. This parameter is ensured by characterization and is not 100% tested. 2. AC measurement conditions:  RL (connects to VCC): 1.3kΩ (2.5V, 5.5V), 10kΩ (1.7V)  Input pulse voltages: 0.3VCC to 0.7VCC  Input rise and fall times: ≤ 50ns  Input and output timing reference voltages: 0.5 x VCC Applicable over recommended operating range from: TAI = −40°C to +85°C, VCC = 1.7V to 5.5V, CL = 100pF (unless otherwise noted). Test conditions are listed in Note 2. Symbol Parameter 1.7V 2.5V, 5.0V UnitsMin Max Min Max fSCL Clock Frequency, SCL 400 1000 kHz tLOW Clock Pulse Width Low 1300 400 ns tHIGH Clock Pulse Width High 600 400 ns tI Noise Suppression Time(1) 100 50 ns tAA Clock Low to Data Out Valid 50 900 50 550 ns tBUF Time the bus must be free before a new transmission can start(1) 1300 500 ns tHD.STA Start Condition Hold Time 600 250 ns tSU.STA Start Condition Set-up Time 600 250 ns tHD.DAT Data In Hold Time 0 0 ns tSU.DAT Data In Set-up Time 100 100 ns tR Inputs Rise Time(1) 300 300 ns tF Inputs Fall Time(1) 300 100 ns tSU.STO Stop Condition Set-up Time 600 250 ns tDH Data Out Hold Time 50 50 ns tWR Write Cycle Time 5 5 ms Endurance(1) 25°C, Page Mode, 3.3V 1,000,000 Write Cycles

9AT24C32D [DATASHEET] Atmel-8866A-SEEPROM-AT24C32D-Datasheet_082013 7. Device Addressing The 32K EEPROM requires an 8-bit device address word following a Start condition to enable the chip for a Read or Write operation. The device address word consists of a mandatory ‘1010’ sequence for the first four most significant bits which is known as the device type identifier. These four bits are bit 7, bit 6, bit 5, and bit 4 as seen in Figure 7-1. This is common to all 2-wire Serial EEPROM devices. The next three bits are the A2, A1, and A0 hardware address select bits which allow as many as eight devices on the same bus. These bits must compare to their corresponding hard wired input pins, A2, A1, and A0. The A2, A1, and A0 pins use an internal proprietary circuit that biases them to a logic low condition if the pins are allowed to float. When utilizing the 5-ball WLCSP or the 5-lead SOT-23 packages, the A2, A1, and A0 pins are not available. The A2, A1, and A0 pins are internally pulled to ground and thus the A2, A1, and A0 device address bits must always be set to a Logic 0 to communicate with the device. This condition is depicted in Figure 7-1 below. The eighth bit of the device address is the Read/write operation select bit. A Read operation is initiated if this bit is a Logic 1, and a Write operation is initiated if this bit is a Logic 0. Upon a successful comparison of the device address, the EEPROM will output a zero during the following clock cycle. If a compare is not made, the device will not acknowledge and will instead return to a standby state. Figure 7-1. Device Addressing Data Security:The AT24C32D has a hardware data protection scheme that allows the user to write protect the whole memory when the WP pin is at VCC. Package Device Type Identifier Hardware Address Select Bits R/W Select Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 SOIC, TSSOP, UDFN, XDFN, and VFBGA 1 0 1 0 A2 A1 A0 R/W SOT-23 and WLCSP 1 0 1 0 0 0 0 R/W MSB LSB

AT24C32D [DATASHEET] Atmel-8866A-SEEPROM-AT24C32D-Datasheet_082013 Sequential Read: Sequential Reads are initiated by either a Current Address Read or a Random Address Read. After the microcontroller receives a data word, it responds with an acknowledge. As long as the EEPROM receives an acknowledge, it will continue to increment the data word address and serially clock out sequential data words. When the memory address maximum address is reached, the data word address will roll-over and the Sequential Read will continue from the beginning of the array. The Sequential Read operation is terminated when the microcontroller does not respond with a zero but does generate a Stop condition (See Figure 9-3). Figure 9-3. Sequential Read Note: * = Don’t care bit. SDA LINE S T A R T S T A R T R E A D W R I T E S T O P Device Address Second Word Address Device Address First Word Address Data (n + 1) Data (n + 2) Data (n + x)Data (n) M S B A C K A C K A C K L S B A C K A C K A C K A C K N O A C K R W Dummy Write . . . . . . R W

13AT24C32D [DATASHEET] Atmel-8866A-SEEPROM-AT24C32D-Datasheet_082013 10. Ordering Code Detail Atmel Designator Product Family Device Density Device Revision Shipping Carrier Option Operating Voltage Package Option 32 = 32K 24C = Standard I2C Serial EEPROM B = Bulk (Tubes) T = Tape and Reel M = 1.7V to 5.5V SS = JEDEC SOIC X = TSSOP MA = UDFN ME = XDFN ST = SOT23 U = 5-ball, 3x3 Grid Array, WLCS P C = VFBGA WWU = Wafer Unsawn WDT = Die in Tape and Reel Package Device Grade or Wafer/Die Thickness H = Green, NiPdAu Lead Finish, Industrial Temperature Range (-40°C to +85°C) U = Green, Matte Sn Lead Finish or SnAgCu Solder Ball Finish, Industrial Temperature Range (-40°C to +85°C) 11 = 11mil Wafer Thickness AT24C32D-SSHM-B

AT24C32D [DATASHEET] Atmel-8866A-SEEPROM-AT24C32D-Datasheet_082013 11. Part Markings DRAWING NO. REV. TITLE 24C32DSM A 3/19/13 DL-CSO-Assy_eng@atmel.com AAAAAAAA###% @ATMLHYWW 8-lead SOIC 8-lead TSSOP AAAAAAA ###% @ ATHYWW ### YXX 8-pad XDFN 8-pad UDFN ### H%@ YXX 2.0 x 3.0 mm Body 5-ball WLCSP 1.5 x 2.0 mm Body 8-ball VFBGA PIN 1 ###U YMXX 1.8 x 2.2 mm Body Note 2: Package drawings are not to scale Note 1: designates pin 1 AT24C32D: Package Marking Information Catalog Number Truncation AT24C32D Truncation Code ###: 32D Date Codes Voltages Y = Year M = Month WW = Work Week of Assembly % = Minimum Voltage 2: 2012 6: 2016 A: January 02: Week 2 M: 1.7V min 3: 2013 7: 2017 B: February 04: Week 4 5: 2015 9: 2019 L: December 52: Week 52 Country of Assembly Lot Number Grade/Lead Finish Material @ = Country of Assembly AAA...A = Atmel Wafer Lot Number H: Industrial/NiPdAu U: Industrial/Matte Tin/SnAgCu Trace Code Atmel Truncation XX = Trace Code (Atmel Lot Numbers Correspond to Code) AT: Atmel Example: AA, AB.... YZ, ZZ ATM: Atmel ATML: Atmel ### YXX ###%U YMXX Bottom Mark Top Mark 5-lead SOT-23

15AT24C32D [DATASHEET] Atmel-8866A-SEEPROM-AT24C32D-Datasheet_082013 12. Ordering Codes

12.1 AT24C32D Ordering Information

Notes: 1. Bulk delivery in tubes:  SOIC and TSSOP = 100 per tube 2. Tape and reel delivery:  SOIC = 4k per reel  TSSOP, UDFN, XDFN, SOT23, WLCSP, and VFBGA = 5k per reel 3. Contact Atmel Sales for Wafer sales. Ordering Code Lead Finish Package Voltage Operating Range AT24C32D-SSHM-B(1) NiPdAu (Lead-free/Halogen-free) 8S1 1.7V to 5.5V Industrial Temperature (−40°C to 85°C) AT24C32D-SSHM-T(2) AT24C32D-XHM-B(1) AT24C32D-XHM-T(2) AT24C32D-MAHM-T(2) 8MA2 AT24C32D-MEHM-T(2) 8ME1 AT24C32D-STUM-T(2) Matte Tin (Lead-free/Halogen-free) 5TS1 AT24C32D-UUM-T(2) SnAgCu (Lead-free/Halogen-free) 5U-3 AT24C32D-CUM-T(2) 8U2-1 AT24C32D-WWU11M(3) — Wafer Sale Package Type 8S1 8-lead, 0.150” wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8X 8-lead, 4.40mm body, Plastic Thin Shrink Small Outline (TSSOP) 8MA2 8-pad, 2.00mm x 3.00mm body, 0.50mm pitch, Dual No Lead (UDFN) 8ME1 8-pad, 1.80mm x 2.20mm body, 0.40mm pitch, Extra Thin DFN (XDFN) 5TS1 5-lead, 2.90mm x 1.60mm Plastic Think Shrink Small Outline (SOT23) 5U-3 5-ball, 3x3 Grid Array, Wafer Level Chip Scale (WLCSP) 8U2-1 8-ball, Die Ball Grid Array (VFBGA)

AT24C32D [DATASHEET] Atmel-8866A-SEEPROM-AT24C32D-Datasheet_082013 13. Packaging Information 13.1 8S1 — 8-lead JEDEC SOIC DRAWING NO. REV. TITLE GPC COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 A 1.35 – 1.75 b 0.31 – 0.51 C 0.17 – 0.25 D 4.80 – 5.05 E1 3.81 – 3.99 E 5.79 – 6.20 e 1.27 BSC L 0.40 – 1.27 ØØ 0° – 8° Ø E N TOP VIEW C END VIEW A b L e D SIDE VIEW Package Drawing Contact: packagedrawings@atmel.com 8S1 G 6/22/11 Notes: This drawing is for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 8S1, 8-lead (0.150” Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) SWB

17AT24C32D [DATASHEET] Atmel-8866A-SEEPROM-AT24C32D-Datasheet_082013 13.2 8X — 8-lead TSSOP DRAWING NO. REV. TITLE GPC COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A - - 1.20 A1 0.05 - 0.15 A2 0.80 1.00 1.05 D 2.90 3.00 3.10 2, 5 E 6.40 BSC E1 4.30 4.40 4.50 3, 5 b 0.19 – 0.30 4 e 0.65 BSC L 0.45 0.60 0.75 L1 1.00 REF C 0.09 - 0.20 Side View End ViewTop View A L D N b Pin 1 indicator this corner E e Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15mm (0.006in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25mm (0.010in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07mm. 5. Dimension D and E1 to be determined at Datum Plane H. Package Drawing Contact: packagedrawings@atmel.com 8X D 6/22/11 8X, 8-lead 4.4mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) TNR C

AT24C32D [DATASHEET] Atmel-8866A-SEEPROM-AT24C32D-Datasheet_082013 13.3 8MA2 — 8-pad UDFN TITLE DRAWING NO. GPC REV. Package Drawing Contact: packagedrawings@atmel.com 8MA2YNZ C 8MA2, 8-pad, 2 x 3 x 0.6 mm Body, Thermally Enhanced Plastic Ultra Thin Dual Flat No Lead Package (UDFN) COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 1.90 2.00 2.10 E 2.90 3.00 3.10 D2 1.40 1.50 1.60 E2 1.20 1.30 1.40 A 0.50 0.55 0.60 A1 0.0 0.02 0.05 A2 – – 0.55 C 0.152 REF L 0.30 0.35 0.40 e 0.50 BSC b 0.18 0.25 0.30 3 K 0.20 – – 9/6/12 E e (6x) L (8x) b (8x) Pin#1 ID A Pin 1 ID D C K

19AT24C32D [DATASHEET] Atmel-8866A-SEEPROM-AT24C32D-Datasheet_082013 13.4 8ME1 — 8-pad XDFN Package Drawing Contact: packagedrawings@atmel.com GPC DRAWING NO. REV. TITLE COMMON DIMENSIONS (Unit of Measure = mm) DTP SYMBOL MIN NOM MAX NOTE 0.00 1.70 2.10 0.15 0.26 A D E b e L 1.80 2.20 0.20

0.40 TYP

1.20 REF

0.30 0.40 0.05 1.90 2.30 0.25 0.35 End View 8ME1 B 9/10/2012 8ME1, 8-pad (1.80mm x 2.20mm body) Extra Thin DFN (XDFN) Top View 6 57 E D 1 2 PIN #1 ID 0.10 0.15 b L b e PIN #1 ID A Side View

AT24C32D [DATASHEET] Atmel-8866A-SEEPROM-AT24C32D-Datasheet_082013 13.5 5TS1 — 5-lead SOT23 DRAWING NO. REV. TITLE GPC Package Drawing Contact: packagedrawings@atmel.com 5TS1 D 5/31/12 5TS1, 5-lead 1.60mm Body, Plastic Thin Shrink Small Outline Package (Shrink SOT) TSZ COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A - - 1.00 A1 0.00 - 0.10 A2 0.70 0.90 1.00 c 0.08 - 0.20 3 D 2.90 BSC 1,2 E 2.80 BSC 1,2 E1 1.60 BSC 1,2 L1 0.60 REF e 0.95 BSC e1 1.90 BSC b 0.30 - 0.50 3,4 1. Dimension D does not include mold flash, protrusions or gate burrs. Mold flash, protrusions or gate burrs shall not exceed 0.15 mm per end. Dimension E1 does not include interlead flash or protrusion. Interlead flash or protrusion shall not exceed 0.15 mm per side. 2. The package top may be smaller than the package bottom. Dimensions D and E1 are determined at the outermost extremes of the plastic body exclusive of mold flash, tie bar burrs, gate burrs and interlead flash, but including any mismatch between the top and bottom of the plastic body. 3. These dimensions apply to the flat section of the lead between 0.08 mm and 0.15 mm from the lead tip. 4. Dimension "b" does not include dambar protrusion. Allowable dambar protrusion shall be 0.08 mm total in excess of the "b" dimension at maximum material condition. The dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and an adjacent lead shall not be less than 0.07 mm. This drawing is for general information only. Refer to JEDEC Drawing MO-193, Variation AB for additional information. 5 4 L C END VIEW C AA2 b e PLANE SEATING D SIDE VIEW E TOP VIEW

21AT24C32D [DATASHEET] Atmel-8866A-SEEPROM-AT24C32D-Datasheet_082013 13.6 5U-3 — 5-ball, WLCSP DRAWING NO. REV. TITLE GPC 5U-3 A 7/25/13 5U-3, 5-ball Wafer Level Chip Scale Package (WLCSP) - AT24C32D GCQ COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN TYP MAX NOTE A 0.270 0.309 0.348 A1 0.078 - 0.139 A2 0.175 0.200 0.225 E Contact Atmel for details e1 0.529 e2 0.400 D Contact Atmel for details d1 0.600 b 0.148 0.168 0.188 Package Drawing Contact: packagedrawings@atmel.com TOP VIEW PIN ASSIGNMENT MATRIX A B C GND WP SDA V SCL SIDE VIEW E D A A B C 1 2 3Pin 1 -A- -B- -C- BALL SIDE e1 B Øb 23 1 C A Pin 1 n 0.015m Cj n 0.05m CAB d 0.03 C d 0.03 (4X) cc n/a n/an/a n/a

AT24C32D [DATASHEET] Atmel-8866A-SEEPROM-AT24C32D-Datasheet_082013 13.7 8U2-1 — 8-ball VFBGA DRAWING NO. REV. TITLE GPC Package Drawing Contact: packagedrawings@atmel.com 8U2-1 F 3/20/12 8U2-1, 8-ball, 2.35 x 3.73 mm Body, 0.75 mm pitch, COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A 0.81 0.91 1.00 A1 0.15 0.20 0.25 A2 0.40 0.45 0.50 b 0.25 0.30 0.35 D 2.35 BSC E 3.73 BSC e 0.75 BSC e1 0.74 REF d 0.75 BSC d1 0.80 REF 2. Dimension 'b' is measured at the maximum solder ball diameter. 1. This drawing is for general information. Notes: A d 0.08 C C f 0.10 C Øb j n0.15 m CAB j n0.08 m C A (4X)d 0.10 B A1 BALL PAD CORNER D E SIDE VIEWTOP VIEW e (e1) d D C B A A1 BALL PAD CORNER (d1)

8 SOLDER BALLS

23AT24C32D [DATASHEET] Atmel-8866A-SEEPROM-AT24C32D-Datasheet_082013 14. Revision History Doc. Rev. Date Comments 8866A 08/2013 Split AT24C32D from AT24C64D due to growing differences in package offerings. Add 5-ball WLCSP package. Update template and Atmel logos.

Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 | www.atmel.com © 2013 Atmel Corporation. / Rev.: Atmel-8866A-SEEPROM-AT24C32D-Datasheet_082013. Atmel®, Atmel logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDIT IONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS P RODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMI TATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or c ompleteness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel d oes not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automo tive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical A pplications”) without an Atmel officer's specific written consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for t he operation of nuclear facilities and weapons systems. Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.