AT24C32C_14 ATMEL
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 28
Technical content
(Features Low-voltage and Standard-voltage Operation Internally Organized 4096 x 8, 8192 x 8 2-Wire Serial Interface Schmitt Trigger, Filtered Inputs for Noise Suppression Bi-directional Data Transfer Protocol 1 MHz (5.0V) and 400 KHz (1.8V Compatibility) Write Protect Pin for Hardware Data Protection 32-Byte Page Write Mode (Partial Page Writes Allowed) Self-Timed Write Cycle (5 ms max) High Reliability – Endurance: 1 Million Write Cycles – Data Retention: 100 Years Lead-free/Halogen-free Devices 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead Ultra Lead Frame Land Grid Array (ULA), 8-lead TSSOP, 8-lead Ultra Thin Mini-MAP (MLP2x3), and 8-ball dBGA2 Packages. Die Sales: Wafer Form, Waffle Pack, and Bumped Wafers
Description
The AT24C32C/64C provides 32,768/65,536 bits of serial electrically erasable and programmable read only memory (EEPROM) organized as 4096/8192 words of 8 bits each. The device’s cascadable feature allows up to 8 devices to share a common 2- wire bus. The device is optimized for use in many industrial and commercial applica- tions where low power and low voltage operation are essential. The AT24C32C/64C is available in space saving 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead Ultra Lead Frame Land Grid Array (ULA), 8-lead TSSOP, 8-lead Ultra Thin Mini-MAP (MLP2x3) and, 8- ball dBGA2 packages and is accessed via a 2-wire serial interface. In addition, the entire family is available in 1.8V (1.8 to 5.5V) version. 2-Wire Serial EEPROM 32K (4096 x 8) 64K (8192 x 8) AT24C32C AT24C64C 5298A–SEEPR–1/08 Not Recommended for New Design Pin Configurations Pin Name Function A0 - A2 Address Inputs SDA Serial Data SCL Serial Clock Input WP Write Protect 8-lead Ultra Thin Mini-MAP (MLP 2x3) GND VCC WP SCL SDA Bottom View 8-lead PDIP GND VCC WP SCL SDA 8-lead TSSOP GND VCC WP SCL SDA 8-lead SOIC GND VCC WP SCL SDA 8-ball dBGA2 GND VCC WP SCL SDA Bottom View 8-lead Ultra Lead Frame Land Grid Array (ULA) GND VCC WP SCL SDA Bottom View
5298A–SEEPR–1/08 AT24C32C/64C 1. Block Diagram Absolute Maximum Ratings* Maximum Ratings” may cause permanent dam- age to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Voltage on Any Pin START STOP LOGIC VCC GND WP SCL SDA SERIAL CONTROL LOGIC EN H.V. PUMP/TIMING EEPROM DATA RECOVERY SERIAL MUX X DEC DOUT/ACK LOGIC COMP LOAD INC DATA WORD ADDR/COUNTER Y DEC R/W DOUT DIN LOAD DEVICE ADDRESS COMPARATOR
5298A–SEEPR–1/08 AT24C32C/64C 2. Pin Description SERIAL CLOCK (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative edge clock data out of each device. SERIAL DATA (SDA): The SDA pin is bidirectional for serial data transfer. This pin is open-drain driven and may be wire-ORed with any number of other open-drain or open collector devices. DEVICE/ADDRESSES (A2, A1, A0): The A2, A1 and A0 pins are device address inputs that are hard wired or left not connected for hardware compatibility with other AT24CXX devices. When the pins are hardwired, as many as eight 32K/64K devices may be addressed on a single bus system (device addressing is discussed in detail under the Device Addressing section). If the pins are left floating, the A2, A1 and A0 pins will be internally pulled down to GND if the capaci- tive coupling to the circuit board V CC plane is <3pF. If coupling is >3pF, Atmel ® recommends connecting the address pins to GND. WRITE PROTECT (WP): The write protect input, when connected to GND, allows normal write operations. When WP is connected high to VCC, all write operations to the memory are inhibited. If the pin is left floating, the WP pin will be internally pulled down to GND if the capacitive cou- pling to the circuit board V CC plane is <3pF. If coupling is >3pF, Atmel recommends connecting the pin to GND.
5298A–SEEPR–1/08 AT24C32C/64C 3. Memory Organization AT24C32C/64C, 32/64K SERIAL EEPROM: The 32K/64K is internally organized as 128/256 pages of 32 bytes each. Random word addressing requires a 12/13 bit data word address. Note: 1. This parameter is characterized and is not 100% tested. Note: 1. V IL min and VIH max are reference only and are not tested. Pin Capacitance(1) Applicable over recommended operating range from TA =2 5°C, f = 1.0 MHz, VCC = +1.8V to 5.5V Symbol Test Condition Max Units Conditions CI/O Input/Output Capacitance (SDA) 8 pF V I/O =0 V CIN Input Capacitance (A0,A 1,A 2, SCL) 6 pF V IN =0 V DC Characteristics Applicable over recommended operating range from: TAI = -40 to +85°C, VCC = +1.8 to +5.5V (unless otherwise noted) Symbol Parameter Test Condition Min Typ Max Units VCC1 Supply Voltage 1.8 5.5 V ICC1 Supply Current V CC = 5.0V READ at 400 kHz 0.4 1.0 mA ICC2 Supply Current V CC = 5.0V WRITE at 400 kHz 2.0 3.0 mA ISB1 Standby Current (1.8V option) VCC = 1.8V VIN =V CC or VSS 1.0 µA VCC = 5.5V 6.0 µA ILI Input Leakage Current VCC = 5.0V VIN =V CC or VSS 0.10 3.0 µA ILO Output Leakage Current VCC = 5.0V VOUT =V CC or VSS 0.05 3.0 µA VIL Input Low Level(1) −0.6 V CC x 0.3 V VIH Input High Level(1) VCC x 0.7 V CC + 0.5 V VOL2 Output Low Level V CC = 3.0V I OL = 2.1 mA 0.4 V VOL1 Output Low Level V CC = 1.8V I OL = 0.15 mA 0.2 V
5298A–SEEPR–1/08 AT24C32C/64C Notes: 1. This parameter is ensured by characterization. 2. AC measurement conditions: RL (connects to VCC): 1.3 kΩ (2.5V, 5.0V), 10 kΩ (1.8V) Input pulse voltages: 0.3 VCC to 0.7 VCC Input rise and fall times: ≤ 50 ns Input and output timing reference voltages: 0.5 VCC AC Characteristics Applicable over recommended operating range from TAI = -40°Ct o+ 8 5°C, VCC = +1.8V to +5.5V, CL = 1 TTL Gate and 100 pF (unless otherwise noted) Symbol Parameter 1.8-volt 5.0-volt Min Max Min Max Units fSCL Clock Frequency, SCL 400 1000 kHz tLOW Clock Pulse Width Low 1.3 0.4 µs tHIGH Clock Pulse Width High 0.6 0.4 µs ti Noise Suppression Time(1) 100 50 ns tAA Clock Low to Data Out Valid 0.05 0.9 0.05 0.55 µs tBUF Time the bus must be free before a new transmission can start(1) 1.3 0.5 µs tHD.STA Start Hold Time 0.6 0.25 µs tSU.STA Start Set-up Time 0.6 0.25 µs tHD.DAT Data In Hold Time 0 0 µs tSU.DAT Data In Set-up Time 100 100 ns tR Inputs Rise Time(1) 0.3 0.3 µs tF Inputs Fall Time(1) 300 100 ns tSU.STO Stop Set-up Time 0.6 0.25 µs tDH Data Out Hold Time 50 50 ns tWR Write Cycle Time 5 5 ms Endurance(1) 25°C, Page Mode, 3.3V 1,000,000 Write Cycles
5298A–SEEPR–1/08 AT24C32C/64C 4. Device Operation CLOCK and DATA TRANSITIONS: The SDA pin is normally pulled high with an external device. Data on the SDA pin may change only during SCL low time periods (refer to Data Valid- ity timing diagram). Data changes during SCL high periods will indicate a start or stop condition as defined below. START CONDITION: A high-to-low transition of SDA with SCL high is a start condition which must precede any other command (refer to Start and Stop Definition timing diagram). STOP CONDITION: A low-to-high transition of SDA with SCL high is a stop condition. After a read sequence, the stop command will place the EEPROM in a standby power mode (refer to Start and Stop Definition timing diagram). ACKNOWLEDGE: All addresses and data words are serially transmitted to and from the EEPROM in 8-bit words. The EEPROM sends a zero during the ninth clock cycle to acknowl- edge that it has received each word. STANDBY MODE: The AT24C32C/64C features a low power standby mode which is enabled: a) upon power-up and b) after the receipt of the Stop bit and the completion of any internal operations. SOFTWARE RESET: After an interruption in protocol, power loss or system reset, and 2-wire part can be protocol reset by following these steps: (a) Create a start bit condition, (b) clock 9 cycles, (c) create another start bit followed by stop bit condition as shown below. The device is ready for next communication after above steps have been completed. Figure 4-1. Software Reset Start bit Stop bitStart bitDummy Clock Cycles SCL SDA 123 89
5298A–SEEPR–1/08 AT24C32C/64C 5. Bus Timing SCL: Serial Clock, SDA: Serial Data I/O 6. Write Cycle Timing SCL: Serial Clock, SDA: Serial Data I/O Note: 1. The write cycle time t WR is the time from a valid stop condition of a write sequence to the end of the internal clear/write cycle. SCL SDA IN SDA OUT tF tHIGH tLOW tLOW tR tAA tDH tBUF twr (1) STOP CONDITION START CONDITION WORDn ACK8th BIT SCL SDA
5298A–SEEPR–1/08 AT24C32C/64C 7. Data Validity 8. Start and Stop Definition 9. Output Acknowledge SDA SCL DATA STABLE DATA STABLE DATA CHANGE SDA SCL START STOP SCL DATA IN DATA OUT START ACKNOWLEDGE 981
5298A–SEEPR–1/08 AT24C32C/64C 10. Device Addressing The 32K/64K EEPROM requires an 8-bit device address word following a start condition to enable the chip for a read or write operation (see Figure 12-1 on page 11). The device address word consists of a mandatory one, zero sequence for the first four most significant bits as shown. This is common to all 2-wire EEPROM devices. The 32K/64K uses the three device address bits A2, A1, A0 to allow as many as eight devices on the same bus. These bits must compare to their corresponding hardwired input pins. The A2, A1, and A0 pins use an internal proprietary circuit that biases them to a logic low condition if the pins are allowed to float. The eighth bit of the device address is the read/write operation select bit. A read operation is ini- tiated if this bit is high and a write operation is initiated if this bit is low. Upon a compare of the device address, the EEPROM will output a zero. If a compare is not made, the device will return to standby state. DATA SECURITY: The AT24C32C/64C has a hardware data protection scheme that allows the user to write protect the entire memory when the WP pin is at V CC. 11. Write Operations BYTE WRITE: A write operation requires two 8-bit data word addresses following the device address word and acknowledgment. Upon receipt of this address, the EEPROM will again respond with a zero and then clock in the first 8-bit data word. Following receipt of the 8-bit data word, the EEPROM will output a zero and the addressing device, such as a microcontroller, must terminate the write sequence with a stop condition. At this time the EEPROM enters an internally-timed write cycle, t WR, to the nonvolatile memory. All inputs are disabled during this write cycle and the EEPROM will not respond until the write is complete (see Figure 12-2 on page 11). PAGE WRITE: The 32K/64K EEPROM is capable of 32-byte page writes. A page write is initiated the same way as a byte write, but the microcontroller does not send a stop condition after the first data word is clocked in. Instead, after the EEPROM acknowledges receipt of the first data word, the microcontroller can transmit up to 31 more data words. The EEPROM will respond with a zero after each data word received. The microcontroller must ter- minate the page write sequence with a stop condition (see Figure 12-3 on page 11). The data word address lower 5 bits are internally incremented following the receipt of each data word. The higher data word address bits are not incremented, retaining the memory page row location. When the word address, internally generated, reaches the page boundary, the follow- ing byte is placed at the beginning of the same page. If more than 32 data words are transmitted to the EEPROM, the data word address will “roll over” and previous data will be overwritten. ACKNOWLEDGE POLLING: Once the internally-timed write cycle has started and the EEPROM inputs are disabled, acknowledge polling can be initiated. This involves sending a start condition followed by the device address word. The read/write bit is representative of the operation desired. Only if the internal write cycle has completed will the EEPROM respond with a zero, allowing the read or write sequence to continue.
5298A–SEEPR–1/08 AT24C32C/64C Figure 12-6. Sequential Read
5298A–SEEPR–1/08 AT24C32C/64C Notes: 1. “-B” denotes Bulk. 2. “-T” denotes tape and reel. SOIC = 4K per reel. TSSOP, Ultra Thin Mini-MAP and dBGA2 = 5K per reel. 3. Available in waffle pack, tape and reel, and wafer form; order as SL788 for inkless wafer form. Bumped die available upon request. Please contact Serial Interface Marketing. Ordering Code Voltage Package Operation Range AT24C32C-PU (Bulk form only) AT24C32CN-SH-B(1) (NiPdAu Lead Finish) AT24C32CN-SH-T(2) (NiPdAu Lead Finish) AT24C32C-TH-B(1) (NiPdAu Lead Finish) AT24C32C-TH-T(2) (NiPdAu Lead Finish) AT24C32CY6-YH-T(2) (NiPdAu Lead Finish) AT24C32CD3-DH-T(2) (NiPdAu Lead Finish) AT24C32CU2-UU-T(2) 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 8P3 8S1 8S1 8A2 8A2 8Y6 8D3 8U2-1 Lead-free/Halogen-free Industrial Temperature (-40°Ct o8 5°C) AT24C32C-W-11 (3) 1.8 Die Sale Industrial Temperature (-40°Ct o8 5°C) Package Type 8Y6 8-lead, 2.00mm x 3.00mm Body, 0.50mm Pitch, Ultra Thin Mini-MAP, Dual no Lead Package (DFN), (MLP 2x3) 8P3 8-lead, 0.300” Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150” Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 4.4 mm Body, Plastic, Thin Shrink Small Outline Package (TSSOP) 8U2-1 8-ball, die Ball Grid Array Package (dBGA2) 8D3 8-lead, 1.80 mm x 2.20 mm Body, Ultra Lead Frame Land Grid Array (ULA) Options -1.8 Low Voltage (1.8V to 5.5V)
5298A–SEEPR–1/08 AT24C32C/64C Notes: 1. “-B” denotes Bulk. 2. “-T” denotes tape and reel. SOIC = 4K per reel. TSSOP, Ultra Thin Mini-MAP and dBGA2 = 5K per reel. 3. Available in waffle pack, tape and reel, and wafer form; order as SL788 for inkless wafer form. Bumped die available upon request. Please contact Serial Interface Marketing. Ordering Code Voltage Package Operation Range AT24C64C-PU (Bulk form only) AT24C64CN-SH-B(1) (NiPdAu Lead Finish) AT24C64CN-SH-T(2) (NiPdAu Lead Finish) AT24C64C-TH-B(1) (NiPdAu Lead Finish) AT24C64C-TH-T(2) (NiPdAu Lead Finish) AT24C64CY6-YH-T(2) (NiPdAu Lead Finish) AT24C64CD3-DH-T(2) (NiPdAu Lead Finish) AT24C64CU2-UU-T(2) 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 8P3 8S1 8S1 8A2 8A2 8Y6 8D3 8U2-1 Lead-free/Halogen-free Industrial Temperature (-40°Ct o8 5°C) AT24C64C-W-11 (3) 1.8 Die Sale Industrial Temperature (-40°Ct o8 5°C) Package Type 8Y6 8-lead, 2.00mm x 3.00mm Body, 0.50mm Pitch, Ultra Thin Mini-MAP, Dual no Lead Package (DFN), (MLP 2x3) 8P3 8-lead, 0.300” Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150” Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 4.4 mm Body, Plastic, Thin Shrink Small Outline Package (TSSOP) 8U2-1 8-ball, die Ball Grid Array Package (dBGA2) 8D3 8-lead, 1.80 mm x 2.20 mm Body, Ultra Lead Frame Land Grid Array (ULA) Options -1.8 Low Voltage (1.8V to 5.5V)
5298A–SEEPR–1/08 AT24C32C/64C 13. Part Marking Scheme 13.1 8-PDIP 13.2 8-SOIC TOP MARK Seal Year Y = SEAL YEAR WW = SEAL WEEK | Seal Week 6: 2006 0: 2010 02 = Week 2 | | | 7: 2007 1: 2011 04 = Week 4 A T M L U Y W W 9: 2009 3: 2013 :: : :::: :: 3 2 C 1 52 = Week 52 * Lot Number Lot Number to Use ALL Characters in Marking | BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark TOP MARK Seal Year Y = SEAL YEAR WW = SEAL WEEK | Seal Week 6: 2006 0: 2010 02 = Week 2 | | | 7: 2007 1: 2011 04 = Week 4 32C 1 52 = Week 52 * Lot Number Lot Number to Use ALL Characters in Marking | BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark
5298A–SEEPR–1/08 AT24C32C/64C 13.3 8-TSSOP 13.4 8-Ultra Thin Mini MAP TOP MARK Pin 1 Indicator (Dot) Y = SEAL YEAR WW = SEAL WEEK | 6: 2006 0: 2010 02 = Week 2 3 2 C 1 50 = Week 50 BOTTOM MARK P H A A A A A A A <- Pin 1 Indicator TOP MARK Y = YEAR OF ASSEMBLY |---|---|---| 32C XX = ATMEL LOT NUMBER TO COORESPOND WITH |---|---|---| NSEB TRACE CODE LOG BOOK. |---|---|---| YXX |---|---|---| Y = SEAL YEAR * 6: 2006 0: 2010 | 7: 2007 1: 2011 Pin 1 Indicator (Dot) 8: 2008 2: 2012 9: 2009 3: 2013
5298A–SEEPR–1/08 AT24C32C/64C 13.5 8-ULA TOP MARK Y = YEAR OF ASSEMBLY |---|---|---| XX = ATMEL LOT NUMBER TO COORESPOND WITH 2B C NSEB TRACE CODE LOG BOOK. YXX |---|---|---| * Y = BUILD YEAR | 6: 2006 Pin 1 Indicator (Dot) 7: 2007 8: 2008 Etc...
5298A–SEEPR–1/08 AT24C32C/64C 14. Part Marking Scheme 14.1 8-PDIP 14.2 8-SOIC TOP MARK Seal Year Y = SEAL YEAR WW = SEAL WEEK | Seal Week 6: 2006 0: 2010 02 = Week 2 | | | 7: 2007 1: 2011 04 = Week 4 A T M L U Y W W 9: 2009 3: 2013 :: : :::: :: 6 4 C 1 52 = Week 52 * Lot Number Lot Number to Use ALL Characters in Marking | BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark TOP MARK Seal Year Y = SEAL YEAR WW = SEAL WEEK | Seal Week 6: 2006 0: 2010 02 = Week 2 | | | 7: 2007 1: 2011 04 = Week 4 64C 1 52 = Week 52 * Lot Number Lot Number to Use ALL Characters in Marking | BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark
5298A–SEEPR–1/08 AT24C32C/64C 14.3 8-TSSOP 14.4 8-Ultra Thin Mini MAP TOP MARK Pin 1 Indicator (Dot) Y = SEAL YEAR WW = SEAL WEEK | 6: 2006 0: 2010 02 = Week 2 6 4 C 1 50 = Week 50 BOTTOM MARK P H A A A A A A A <- Pin 1 Indicator TOP MARK Y = YEAR OF ASSEMBLY |---|---|---| 64C XX = ATMEL LOT NUMBER TO COORESPOND WITH |---|---|---| NSEB TRACE CODE LOG BOOK. |---|---|---| YXX |---|---|---| Y = SEAL YEAR * 6: 2006 0: 2010 | 7: 2007 1: 2011 Pin 1 Indicator (Dot) 8: 2008 2: 2012 9: 2009 3: 2013
5298A–SEEPR–1/08 AT24C32C/64C 14.5 8-ULA TOP MARK Y = YEAR OF ASSEMBLY |---|---|---| XX = ATMEL LOT NUMBER TO COORESPOND WITH 2C C NSEB TRACE CODE LOG BOOK. YXX |---|---|---| * Y = BUILD YEAR | 6: 2006 Pin 1 Indicator (Dot) 7: 2007 8: 2008 Etc...
5298A–SEEPR–1/08 AT24C32C/64C 15. Packaging Information 8Y6 - MLP
2325 Orchard Parkway
San Jose, CA 95131 TITLE DRAWING NO. R REV. 8Y6, 8-lead 2.0 x 3.0 mm Body, 0.50 mm Pitch, Utlra Thin Mini-Map, Dual No Lead Package (DFN) ,(MLP 2x3) D8Y6 10/16/07 Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-229, for proper dimensions, tolerances, datums, etc. 2. Dimension b applies to metallized terminal and is measured between 0.15 mm and 0.30 mm from the terminal tip. If the terminal has the optional radius on the other end of the terminal, the dimension should not be measured in that radius area. 3. Soldering the large thermal pad is optional, but not recommended. No electrical connection is accomplished to the device through this pad, so if soldered it should be tied to ground COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 2.00 BSC E 3.00 BSC D2 1.40 1.50 1.60 E2 - - 1.40 A - - 0.60 A1 0.0 0.02 0.05 A2 - - 0.55 A3 0.20 REF L 0.20 0.30 0.40 e 0.50 BSC b 0.20 0.25 0.30 2 A2A2 b (8X)(8X) Pin 1 IDPin 1 ID Pin 1Pin 1 IndexIndex AreaArea A1A1 A3A3 D E A L (8X)L (8X) e (6X)e (6X) 1.50 REF .1.50 REF. D2D2 E2E2
5298A–SEEPR–1/08 AT24C32C/64C 8P3 – PDIP San Jose, CA 95131 TITLE DRAWING NO. R REV. 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) 01/09/02 8P3 B Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information. 2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion. COMMON DIMENSIONS (Unit of Measure = inches) SYMBOL MIN NOM MAX NOTE D E e Lb2 b A2 A N eA c
4 PLCS
A 0.210 2 A2 0.115 0.130 0.195 b 0.014 0.018 0.022 5 b2 0.045 0.060 0.070 6 b3 0.030 0.039 0.045 6 c 0.008 0.010 0.014 D 0.355 0.365 0.400 3 D1 0.005 3 E 0.300 0.310 0.325 4 E1 0.240 0.250 0.280 3 e 0.100 BSC eA 0.300 BSC 4 L 0.115 0.130 0.150 2 Top View Side View End View
5298A–SEEPR–1/08 AT24C32C/64C 8S1 – JEDEC SOIC 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. Note: 3/17/05 8S1, 8-lead (0.150 Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) 8S1 C COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. EE NN TOP VIEW CC E1E1 END VIEW AA bb LL A1A1 ee DD SIDE VIEW
5298A–SEEPR–1/08 AT24C32C/64C 8A2 – TSSOP San Jose, CA 95131 TITLE DRAWING NO. R REV. 5/30/02 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 2.90 3.00 3.10 2, 5 E 6.40 BSC E1 4.30 4.40 4.50 3, 5 A – – 1.20 A2 0.80 1.00 1.05 b 0.19 – 0.30 4 e 0.65 BSC L 0.45 0.60 0.75 L1 1.00 REF 8A2, 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and ad acent lead is 0.07 mm. 5. Dimension D and E1 to be determined at Datum Plane H. 8A2 B Side View End ViewTop View A L D 123 N b Pin 1 indicator this corner E e
5298A–SEEPR–1/08 AT24C32C/64C 8U2-1 - dBGA2 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. PO8U2-1 A 6/17/03 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE 8U2-1, 8-ball, 2.35 x 3.73 mm Body, 0.75 mm pitch, Small Die Ball Grid Array Package (dBGA2) A 0.81 0.91 1.00 A1 0.15 0.20 0.25 A2 0.40 0.45 0.50 b 0.25 0.30 0.35 D 2.35 BSC E 3.73 BSC e 0.75 BSC e1 0.74 REF d 0.75 BSC d1 0.80 REF 5. Dimension 'b' is measured at the maximum solder ball diameter. This drawing is for general information only. d A SIDE VIEW TOP VIEW
8 SOLDER BALLS
A B C D (e1) e A1 BALL PAD CORNER (d1) 5. b DA1 BALL PAD CORNER E
5298A–SEEPR–1/08 AT24C32C/64C 8D3 - ULA 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. 8D3, 8-lead (1.80 x 2.20 mm Body) Ultra Leadframe Land Grid Array (ULLGA) D3 08D3 11/15/05 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A – – 0.40 A1 0.00 – 0.05 D 1.70 1.80 1.90 E 2.10 2.20 2.30 b 0.15 0.20 0.25 e 0.40 TYP e1 1.20 REF L 0.25 0.30 0.35 0.10 0.15 b 6 57 E D 1 2 PIN #1 ID TOP VIEW L b A e PIN #1 ID SIDE VIEW BOTTOM VIEW
5298A–SEEPR–1/08 AT24C32C/64C
Revision History
Doc. Rev. Date Comments 5298A 1/2008 AT24C32C/64C product with date code 2008 work week 14 (814) or later supports 5Vcc operation Initial document release
5298A–SEEPR–1/08 Headquarters International Atmel Corporation San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Room 1219 Chinachem Golden Plaza
77 Mody Road Tsimshatsui
Tel: (852) 2721-9778 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309
78054 Saint-Quentin-en-
9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Product Contact Web Site www.atmel.com Technical Support s_eeprom@atmel.com Sales Contact www.atmel.com/contacts Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN- TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to s pecifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifica lly provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. ©2008 Atmel Corporation. All rights reserved. Atmel ®, logo and combinations thereof, and others, are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.