AT24C32A_07 ATMEL
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 22
Technical content
Features
- Low-Voltage and Standard-Voltage Operation – 2.7 (V CC = 2.7V to 5.5V) – 1.8 (V CC = 1.8V to 5.5V)
- Low-Power Devices (ISB = 6 µA @ 5.5V) Available
- Internally Organized 4096 x 8, 8192 x 8
- Two-wire Serial Interface
- Schmitt Trigger, Filtered Inputs for Noise Suppression
- Bidirectional Data Transfer Protocol
- 400 kHz (1.8V, 2.5V, 2.7V, 5V) Compatibility
- Write Protect Pin for Hardware Data Protection
- 32-byte Page Write Mode (Partial Page Writes Allowed)
- Self-timed Write Cycle (5 ms Max)
- High Reliability – Endurance: 1 Million Write Cycles – Data Retention: 100 Years
- Automotive Devices Available
- 8-lead JEDEC PDIP , 8-lead JEDEC SOIC, 8-lead EIAJ SOIC, 8-lead Mini-MAP (MLP 2x3) and 8-lead TSSOP Packages
- Lead-free/Halogen-free
- Die Sales: Wafer Form, Waffle Pack, and Bumped Wafers
Description
The AT24C32A/64A provides 32,768/65,536 bits of serial electrically erasable and programmable read only memory (EEPROM) organized as 4096/8192 words of 8 bits each. The device’s cascadable feature allows up to 8 devices to share a common two- wire bus. The device is optimized for us e in many industrial and commercial applica- tions where low power and low voltage operation are essential. The AT24C32A/64A is available in space saving 8-lead JEDE C PDIP, 8-lead JEDEC SOIC, 8-lead EIAJ SOIC, 8-lead Mini-MAP (MLP 2x3) and 8-lead TSSOP packages and is accessed via a 2-wire serial interface. In addition, the entire family is available in 2.7V (2.7V to 5.5V) and 1.8V (1.8V to 5.5V) versions. Table 1. Pin Configuration
2 AT24C32A/64A
Figure 1. Block Diagram
3054T–SEEPR–1/07 Pin Description SERIAL CLOCK (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative edge clock data out of each device. SERIAL DATA (SDA): The SDA pin is bidirectional for serial data transfer. This pin is open-drain driven and may be wire-ORed with any number of other open-drain or open collector devices. DEVICE/ADDRESSES (A2, A1, A0): The A2, A1 and A0 pins are device address inputs that are hardwired or left not connected for hardware compatibility with other AT24Cxx devices. When the pins are hardwired, as many as eight 32K/64K devices may be addressed on a single bus system (device addressing is disc ussed in detail under the Device Addressing section). If the pins are left floating, the A2, A1 and A0 pins will be internally pulled down to GND if the capacitive coupling to the circuit board V CC plane is <3 pF. If coupling is >3 pF, Atmel recommends connecting the address pins to GND. WRITE PROTECT (WP): The write protect input, when connected to GND, allows nor- mal write operations. When WP is connected high to V CC, all write operations to the memory are inhibited. If the pin is left floating, the WP pin will be internally pulled down to GND if the capacitive coup ling to the circuit board V CC plane is <3 pF. If coupling is >3 pF, Atmel recommends connecting the pin to GND. Switching WP to V CC prior to a write operation creates a software write protect function. Memory Organization AT24C32A/64A, 32K/64K SERIAL EEPROM: The 32K/64K is internally organized as 128/256 pages of 32 bytes each. Random word addressing requires a 12/13-bit data word address.
4 AT24C32A/64A
Note: 1. This parameter is characterized and is not 100% tested. Note: 1. V IL min and VIH max are reference only and are not tested. Table 2. Pin Capacitance(1) Table 3. DC Characteristics
Note: 1. This parameter is ensured by characterization only. Table 4. AC Characteristics
6 AT24C32A/64A
3054T–SEEPR–1/07 Device Operation CLOCK and DATA TRANSITIONS: The SDA pin is normally pulled high with an exter- nal device. Data on the SDA pin may change only during SCL low time periods (refer to Data Validity timing diagram). Data changes during SCL high periods will indicate a start or stop condition as defined below. START CONDITION: A high-to-low transition of SDA with SCL high is a start condition which must precede any other command (see Figure 5 on page 8). STOP CONDITION: A low-to-high transition of SDA wit h SCL high is a stop condition. After a read sequence, the stop command will place th e EEPROM in a standby power mode (see Figure 5 on page 8). ACKNOWLEDGE: All addresses and data words are serially transmitted to and from the EEPROM in 8-bit words. The EEPROM sends a zero during the ninth clock cycle to acknowledge that it has received each word. STANDBY MODE: The AT24C32A/64A features a lo w power standby mode which is enabled: a) upon power-up and b) after the re ceipt of the stop bit and the completion of any internal operations. MEMORY RESET: After an interruption in protocol, power loss or system reset, any two-wire part can be reset by following these steps: (a) Clock up to 9 cycles, (b) look for SDA hi gh in each cycle while SCL is high and then (c) create a start condition as SDA is high.
8 AT24C32A/64A
Figure 5. Start and Stop Definition Figure 6. Output Acknowledge
3054T–SEEPR–1/07 Device Addressing The 32K/64K EEPROM requires an 8-bit device address word following a start condition to enable the chip for a read or write oper ation (see Figure 7 on page 11). The device address word consists of a mandatory one, zero sequence for the first four most signifi- cant bits as shown. This is common to all 2-wire EEPROM devices. The 32K/64K uses the three device address bits A2, A1, A0 to allow as many as eight devices on the same bus. These bits must compare to their corresponding hardwired input pins. The A2, A1, and A0 pins use an in ternal proprietary circuit that biases them to a logic low condition if the pins are allowed to float. The eighth bit of the device address is the r ead/write operation select bit. A read opera- tion is initiated if this bit is high and a write operation is initiated if this bit is low. Upon a compare of the device address, the EEPROM will output a zero. If a compare is not made, the device will return to standby state. NOISE PROTECTION: Special internal circuitry placed on the SDA and SCL pins pre- vent small noise spikes from activating the device. DATA SECURITY: The AT24C32A/64A has a hardware data protection scheme that allows the user to write protect the entire memory when the WP pin is at V CC. Write Operations BYTE WRITE: A write operation requires two 8-bit data word addresses following the device address word and acknowledgment. Upon receipt of this address, the EEPROM will again respond with a zero and then cloc k in the first 8-bit data word. Following receipt of the 8-bit data word, the EE PROM will output a zero and the addressing device, such as a microcontroller, must te rminate the write sequence with a stop condi- tion. At this time the EEPROM enter s an internally-tim ed write cycle, t WR, to the nonvolatile memory. All inputs are disabled during this write cycle and the EEPROM will not respond until the write is complete (see Figure 8 on page 11). PAGE WRITE: The 32K/64K EEPROM is capable of 32-byte page writes. A page write is initiated the same way as a byte write, but the microcontroller does not send a stop condition after the first data wo rd is clocked in. Instead, after the EEPROM acknowledges receipt of the first data word, the microcontroller can transmit up to 31 more data words. The EEPROM will respond with a zero after each data word received. The microcontroller must terminate the page write sequence with a stop condition (see Figure 9 on page 11). The data word address lower five bits are internally incremented following the receipt of each data word. The higher data word address bits are not incremented, retaining the memory page row location. When the word address, internally generated, reaches the page boundary, the following byte is placed at the beginning of the same page. If more than 32 data words are transmitted to the EEPROM, the data wo rd address will “roll over” and previous data will be overwritten. ACKNOWLEDGE POLLING: Once the internally-timed write cycle has started and the EEPROM inputs are disabled, acknowledge polling can be initiated. This involves send- ing a start condition followed by the dev ice address word. The read/write bit is representative of the operation desired. Only if the internal write cycle has completed will the EEPROM respond with a zero, allowing the read or write sequence to continue.
10 AT24C32A/64A
3054T–SEEPR–1/07 Read Operations Read operations are initiated the same way as write operations with the exception that the read/write select bit in the device address word is set to one. There are three read operations: current address read, random address read and sequential read. CURRENT ADDRESS READ: The internal data word address counter maintains the last address accessed during the last read or write operation, incremented by one. This address stays valid between operations as long as the chip power is maintained. The address “roll over” during read is from the last byte of the last memory page, to the first byte of the first page. The address “roll over” during write is from the last byte of the cur- rent page to the first byte of the same page. Once the device address with the read/write select bit set to one is clocked in and acknowledged by the EEPROM, the current addr ess data word is serially clocked out. The microcontroller does not respond with an input zero but does generate a following stop condition (see Figure 10 on page 11). RANDOM READ: A random read requires a “dummy” byte write sequence to load in the data word address. Once the device address word and data word address are clocked in and acknowledged by the EEPROM, the mi crocontroller must generate another start condition. The microcontroller now initiate s a current address read by sending a device address with the read/write select bit high. The EEPROM acknowledges the device address and serially clocks out the data word. The microcontroller does not respond with a zero but does generate a following stop condition (see Figure 11 on page 12). SEQUENTIAL READ: Sequential reads are initiated by either a current address read or a random address read. After the microcontro ller receives a data word, it responds with an acknowledge. As long as the EEPROM rece ives an acknowledge, it will continue to increment the data word address and serially clock out sequential data words. When the memory address limit is reached, the data word address will “roll over” and the sequen- tial read will continue. Th e sequential read operatio n is terminated when the microcontroller does not respond with a ze ro but does generate a following stop condi- tion (see Figure 12 on page 12).
12 AT24C32A/64A
Figure 11. Random Read Figure 12. Sequential Read
3054T–SEEPR–1/07 Notes: 1. For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC Characteristics tables. 2. “U” designates Green Package + RoHS compliant. 3. “H” designates Green Package + RoHS compliant, with NiPdAu Lead Finish. 4. Available in waffle pack and wafer form; order as SL788 for inkless wafer form. Bumped die available upon request. Please contact Serial EEPROM Marketing. Ordering Code Package Operation Range AT24C32A-10PU-2.7(2) AT24C32A-10PU-1.8(2) AT24C32AN-10SU-2.7(2) AT24C32AN-10SU-1.8(2) AT24C32AW-10SU-2.7(2) AT24C32AW-10SU-1.8(2) AT24C32A-10TU-2.7(2) AT24C32A-10TU-1.8(2) AT24C32AY1-10YU-1.8(2) (Not recommended for new design) AT24C32AY6-10YH-1.8(3) 8P3 8P3 8S1 8S1 8S2 8S2 8A2 8A2 8Y1 8Y6 Lead-free/Halogen-free/ Industrial Temperature (–40°C to 85°C) AT24C32A-W1.8-11 (4) Die Sale Industrial Temperature (–40°C to 85°C) Package Type 8P3 8-lead, 0.300" Wide, Plastic Dual In-line Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8S2 8-lead, 0.209" Body, Plastic Small Outline (EIAJ SOIC) 8A2 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) 8Y1 8-lead, 4.90 mm x 3.00 mm Body, Dual Footprint, Non-leaded, Miniature Array Package (MAP) 8Y6 8-lead, 2.00 mm x 3.00 mm Body, 0.50 mm Pitch, Ultra Thin Mini-MAP , Dual No Lead Package (DFN), (MLP 2x3 mm) Options –2.7 Low Voltage (2.7V to 5.5V) –1.8 Low Voltage (1.8V to 5.5V)
14 AT24C32A/64A
3054T–SEEPR–1/07 Notes: 1. For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC Characteristics tables. 2. “U” designates Green Package + RoHS compliant. 3. “H” designates Green Package + RoHS compliant, with NiPdAu Lead Finish. 4. Available in waffle pack and wafer form; order as SL788 for inkless wafer form. Bumped die available upon request. Please contact Serial EEPROM Marketing. Ordering Code Package Operation Range AT24C64A-10PU-2.7(2) AT24C64A-10PU-1.8(2) AT24C64AN-10SU-2.7(2) AT24C64AN-10SU-1.8(2) AT24C64AW-10SU-2.7(2) AT24C64AW-10SU-1.8(2) AT24C64A-10TU-2.7(2) AT24C64A-10TU-1.8(2) AT24C64AY1-10YU-1.8(2) (Not recommended for new design) AT24C64AY6-10YH-1.8(3) 8P3 8P3 8S1 8S1 8S2 8S2 8A2 8A2 8Y1 8Y6 Lead-free/Halogen-free/ Industrial Temperature (–40°C to 85°C) AT24C64A-W1.8-11 (4) Die Sale Industrial Temperature (–40°C to 85°C) Package Type 8P3 8-lead, 0.300" Wide, Plastic Dual In-line Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8S2 8-lead, 0.209" Body, Plastic Small Outline (EIAJ SOIC) 8A2 8-lead, 4.4mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) 8Y1 8-lead, 4.90 mm x 3.00 mm Body, Dual Footprint, Non-leaded, Miniature Array Package (MAP) 8Y6 8-lead, 2.00 mm x 3.00 mm Body, 0.50 mm Pitch, Ultra Thin Mini-MAP , Dual No Lead Package (DFN) Options –2.7 Low Voltage (2.7V to 5.5V) –1.8 Low Voltage (1.8V to 5.5V)
3054T–SEEPR–1/07 Package Drawings 8P3 – PDIP
2325 Orchard Parkway
San Jose, CA 95131 TITLE DRAWING NO. R REV. 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) 01/09/02 8P3 B Notes: 1. Thi s drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA, for additional information. 2. Dimen sions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or ro unded lead tips are preferred to ease insertion. COMMON DIMENSIONS (Unit of Measure = inches) SYMBOL MIN NOM MAX NOTE D E e Lb2 b A2 A N eA c
4 PLCS
A – – 0.210 2 A2 0.115 0.1 30 0.195 b 0.014 0.01 8 0.022 5 b2 0.045 0.060 0.070 6 b3 0.0 30 0.0 39 0.045 6 c 0.00 8 0.010 0.014 D 0. 355 0. 365 0.400 3 D1 0.005 – – 3 E 0. 300 0. 310 0. 325 4 E1 0.240 0.250 0.2 80 3 e 0.100 B SC eA 0. 300 BSC 4 L 0.115 0.1 30 0.150 2 Top View Side View End View
16 AT24C32A/64A
3054T–SEEPR–1/07 8S1 – JEDEC SOIC 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. Note: 10/7/03 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) 8S1 B COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. A 1.35 – 1.75 b 0.31 – 0.51 C 0.17 – 0.25 D 4.80 – 5.00 E1 3.81 – 3.99 E 5.79 – 6.20 e 1.27 BSC L 0.40 – 1.27 ∅ 0˚ – 8˚ Top View End View Side View e B D A N E C L
3054T–SEEPR–1/07 8S2 – EIAJ SOIC San Jose, CA 95131 TITLE DRAWING NO. R REV. 8S2, 8-lead, 0.209" Body, Plastic Small Outline Package (EIAJ) 10/7/03 8S2 C COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE Notes: 1. Thi s drawing is for general information only; refer to EIAJ Drawing EDR-7320 for additional information. 2. Mi smatch of the upper and lower dies and resin burrs are not included. 3. It is recommended that upper and lower cavities be equal. If they are different, the larger dimension shall be regarded. 4. Determine s the true geometric position. A 1.70 2.16 A1 0.05 0.25 b 0. 35 0.4 8 5 C 0.15 0. 35 5 D 5.1 3 5. 35 E1 5.1 8 5.40 2, 3 E 7.70 8.26 L 0.51 0. 85 ∅ 0° 8° e 1.27 B SC 4 End View Side View e b A D E N C L Top View
18 AT24C32A/64A
3054T–SEEPR–1/07 8A2 – TSSOP San Jose, CA 95131 TITLE DRAWING NO. R REV. 5/30/02 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 2.90 3.00 3.10 2, 5 E 6.40 B SC E1 4. 30 4.40 4.50 3, 5 A – – 1.20 A2 0. 80 1.00 1.05 b 0.19 – 0. 30 4 e 0.65 B SC L 0.45 0.60 0.75 L1 1.00 REF 8A2, 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Notes: 1. Thi s drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, d atums, etc. 2. Dimen sion D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimen sion E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimen sion b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protr usion and adjacent lead is 0.07 mm. 5. Dimen sion D and E1 to be determined at Datum Plane H. 8A2 B Side View End ViewTop View A L D 123 N b Pin 1 indicator this corner E e
3054T–SEEPR–1/07 8Y1 – MAP A – – 0.90 A1 0.00 – 0.05 D 4.70 4.90 5.10 E 2. 80 3.00 3.20 D1 0. 85 1.00 1.15 E1 0. 85 1.00 1.15 b 0.25 0. 30 0. 35 e 0.65 TYP L 0.50 0.60 0.70 PIN 1 INDEX AREA D E A A1 b 8 7 6 e L PIN 1 INDEX AREA 1 2 3 4 A Top View End View Bottom View Side View San Jose, CA 95131 TITLE DRAWING NO. R REV. 8Y1, 8-lead (4.90 x 3.00 mm Body) MSOP Array Package (MAP) Y1 C8Y1 2/28/03 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE
20 AT24C32A/64A
3054T–SEEPR–1/07 b (8X) Pin 1 ID Pin 1 Index Area D E A L (8X) e (6X) 1.50 REF. San Jose, CA 95131 TITLE DRAWING NO. R REV. 8Y6, 8-lead 2.0 x 3.0 mm Body, 0.50 mm Pitch, Utlra Thin Mini-Map, Dual No Lead Package (DFN), (MLP 2x3) C8Y6 8/26/05 Notes: 1. Thi s drawing is for general information only. Refer to JEDEC Drawing MO-229, for proper dimensions, tolerances, datums, etc. 2. Dimension b applies to metallized terminal and is measured between 0.15 mm and 0.30 mm from the terminal tip. If the terminal has the optional radius on the other end of the terminal, the dimension should not be measured in that radius area. COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 2.00 B SC E 3.00 BSC D2 1.40 1.50 1.60 E2 - - 1.40 A - - 0.60 A1 0.0 0.02 0.05 A2 - - 0.55 A3 0.20 REF L 0.20 0. 30 0.40 e 0.50 B SC b 0.20 0.25 0. 302 A2A2 b (8X)(8X) Pin 1 IDPin 1 ID Pin 1Pin 1 IndexIndex AreaArea A1A1 A3A3 D E A L (8X)L (8X) e (6X)e (6X) 1.50 REF.1.50 REF. D2D2 E2E2 8Y6 - MAP
3054T–SEEPR–1/07
Revision History
Doc. Rev. Date Comments 3054T 1/2007 Implemented revision history. Added Notes to Page 1 recommending new devices.
Printed on recycled paper. 3054T–SEEPR–1/07 Disclaimer: The information in this document is provided in connection with Atmel products. No license, expr ess or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LI ABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTOR Y WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO , THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICU LAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR I NCIDEN- TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTE RRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or comp leteness of the contents of th is document and reserves the rig ht to make changes to specifications and product descriptions at any time withou t notice. Atmel does not make any commitm ent to update the information contained her ein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not int ended, authorized, or warranted for use as components in applications intended to support or sustain life. Atmel Corporation Atmel Operations San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza
77 Mody Road Tsimshatsui
Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Memory San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 Microcontrollers San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602
44306 Nantes Cedex 3, France
13106 Rousset Cedex, France
1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 RF/Automotive Theresienstrasse 2 Postfach 3535
74025 Heilbronn, Germany
1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123
38521 Saint-Egreve Cedex, France
www.atmel.com/literature © 2007 Atmel Corporation. All rights reserved. Atmel ®, logo and combinations thereof, Everywhere You Are ® and others, are registered trade- marks or trademarks of Atmel Corporati on or its subsidiaries. Other terms and product names may be trademarks of others.