AT24C256C ATMEL
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 23
Technical content
Features
- Low-voltage and Standard-voltage Operation ⎯ 1.8 (VCC = 1.8V to 5.5V)
- Internally Organized as 32,768 x 8
- Two-wire Serial Interface
- Schmitt Trigger, Filtered Inputs for Noise Suppression Two-wire Serial EEPROM 256K (32,768 x 8) AT24C256C 8568A–SEEPR–11/08
- Bidirectional Data Transfer Protocol
- 1 MHz (5.0V, 2.7V, 2.5V), and 400 kHz (1.8V) Compatibility
- Write Protect Pin for Hardware and Software Data Protection
- 64-byte Page Write Mode (Partial Page Writes Allowed)
- Self-timed Write Cycle (5 ms Max)
- High Reliability ⎯ Endurance: One Million Write Cycles ⎯ Data Retention: 40 Years
- Lead-free/Halogen-free Devices Available
- 8-lead JEDEC PDIP, 8-lead JEDEC SOIC, EIAJ SOIC, 8-lead Ultra Thin Small Array Package (SAP), 8-lead TSSOP, and 8-ball dBGA2 Packages
- Die Sales: Wafer Form, Waffle Pack and Bumped Wafers
Description
The AT24C256C provides 262,144 bits of serial electrically erasable and programmable read-only memory (EEPROM) organized as 32,768 words of 8 bits each. The device’s cascadable feature allows up to eight devices to share a common two-wire bus. The device is optimized for use in many industrial and commercial applications where low-power and low-volta ge operation are ess ential. The devices are available in space-saving 8-lead JEDEC PDIP, 8-lead JEDEC SOIC, 8-lead Ultra Thin SAP, 8-lead TSSOP, and 8-ball dBGA2 packages. In addition, the entire family is available in a 1.8V (1.8V to 5.5V) version. Table 1. Pin Configurations
2 AT24C256C
Figure 1. Block Diagram
8568A–SEEPR–11/08 1. Pin Descriptions SERIAL CLOCK (SCL): The SCL input is used to positive-edge clock data into each EEPROM device and negative-edge clock data out of each device. SERIAL DATA (SDA): The SDA pin is bidirectional for serial data trans fer. This pin is open drain driven and may be wire-ORed with any number of other open-drain or open-collector devices. DEVICE/PAGE ADDRESSES (A2, A1, A0): The A2, A1, and A0 pins are device address inputs that are hardwired (directly to GND or to VCC) for compatibility with other AT24Cxx devices. When the pins are hardwired, as many as eight 256K devices may be addressed on a single bus system. (Device addressing is discussed in detail under “ Device Addressing”) A device is selected when a corresponding hardware and software match is true. If these pins are left floating, the A2, A1, and A0 pins will be internally pulled down to GND. However, due to capacitive coupling that may appear during customer applications, Atmel recommends always connecting the address pins to a known state. When using a pull-up resistor, Atmel recommends using 10kΩ or less. WRITE PROTECT (WP): The write protect input, when connected to GND, allows normal write operations. When WP is connected directly to VCC, all write operations to the memory are inhibite d. If the pin is left floating, the WP pin will be internally pulled down to GND. However, due to capacit ive coupling that may appear during customer applications, Atmel recommends always connecting the WP pins to a known state. When using a pull-up resistor, Atmel recommends using 10kΩ or less.
4 AT24C256C
addressing requires a 15-bit data word address. Table 2. Pin Capacitance Note: 1. This parameter is characterized and is not 100% tested. Table 3. DC Characteristics Note: 1. V IL min and VIH max are reference only and are not tested.
Table 4. AC Characteristics (Industrial Temperature) TAI = − 40°C to +85°C, VCC = +1.8V to +5.5V, CL = 100 pF (unless otherwise noted). Test conditions are listed in Note 2. Note: 1. This parameter is ensured by characterization and is not 100% tested.
- AC measurement conditions:
6 AT24C256C
start or stop condition as defined below. Figure 2. Data Validity command (refer to Figure 3). Figure 3. Start and Stop Definition command will place the EEPROM in a standby power mode (refer to Figure 3). EEPROM sends a “0” during the ninth clock cycle to acknowledge that it has received each word. receipt of the stop bit and the completion of any internal operations.
8 AT24C256C
Figure 7. Output Acknowledge
most significant bits as shown. This is common to all two-wire EEPROM devices. Figure 8. Device Addressing circuit that biases them to a logic low condition if the pins are allowed to float. and a write operation is initiated if this bit is low. whole memory when the WP pin is at VCC.
10 AT24C256C
EEPROM will not respond until the write is complete (refer to Figure 9). Figure 9. Byte Write PAGE WRITE: The 256K EEPROM is capable of 64-byte page writes. microcontroller must terminate the page write sequence with a stop condition (refer to Figure 10). Figure 10. Page Write respond with a “0”, allowing the read or write sequence to continue.
12 AT24C256C
following stop condition (refer to Figure 13). Figure 13. Sequential Read
8568A–SEEPR–11/08 7. AT24C256C Ordering Codes Ordering Code Voltage Package Operating Range AT24C256C-PU (Bulk Form Only) AT24C256CN-SH-B (1) (NiPdAu Lead Finish) AT24C256CN-SH-T (2) (NiPdAu Lead Finish) AT24C256CW-SH-B (1) (NiPdAu Lead Finish) AT24C256CW-SH-T (2) (NiPdAu Lead Finish) AT24C256C-TH-B (1) (NiPdAu Lead Finish) AT24C256C-TH-T (2) (NiPdAu Lead Finish) AT24C256CY7-YH-T (2) (NiPdAu Lead Finish) AT24C256CU2-UU-T (2) 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 8P3 8S1 8S1 8S2 8S2 8A2 8A2 8Y7 8U2-1 Lead-free/Halogen-free Industrial Temperature (−40°C to 85°C) AT24C256C-W-11 1.8 Die Sale Industrial Temperature (−40°C to 85°C) Note: 1. “-B” denotes bulk. EIAJ = 2K per reel. 3. Available in tape & reel and wafer form; order as SL788 for inkless wafer form. Bumped die available upon request. Contact Serial Interface Marketing. Package Type 8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline Package (JEDEC SOIC) 8S2 8-lead, 0.200” Wide, Plastic Gull Wing Small Outline Package (EIAJ SOIC) 8U2-1 8-ball, die Ball Grid Array Package (dBGA2) 8A2 8-lead, 4.40 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) 8Y7 8-lead, 6.00 mm x 4.90 mm Body, Ultra Thin, Dual Footprint, Non-leaded, Small Array Package (SAP) Options Ӎ1.8 Low-voltage (1.8V to 5.5V)
14 AT24C256C
8568A–SEEPR–11/08 8. Part Marketing Scheme 8-PDIP Top Mark Seal Year Seal Week Y = SEAL YEAR WW = SEAL WEEK 6: 2006 0: 2010 02 = Week 2 --- --- --- --- --- --- --- --- 04 = Week 4 7: 2007 1: 2011 A T M L U Y W W --- --- --- --- --- --- --- E C 50 = Week 50 Lot Number 52 = Week 52 --- --- --- --- --- --- --- --- Lot Number to Use ALL Characters in Marking BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark 8-SOIC Top Mark Seal Year Seal Week Y = SEAL YEAR WW = SEAL WEEK 6: 2006 0: 2010 02 = Week 2 --- --- --- --- --- --- --- --- 04 = Week 4 7: 2007 1: 2011 A T M L H Y W W --- --- --- --- --- --- --- E C 50 = Week 50 Lot Number 52 = Week 52 --- --- --- --- --- --- --- --- Lot Number to Use ALL Characters in Marking BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark 8-TSSOP Top Mark Pin 1 Indicator (Dot) Y = SEAL YEAR WW = SEAL WEEK 6: 2006 0: 2010 02 = Week 2 --- --- --- --- 7: 2007 1: 2011 04 = Week 4 W --- --- --- --- E C 50 = Week 50 --- Bottom Mark XX = Country of Origin --- --- --- --- --- --- --- X X A A A A A A A Pin 1 Indicator
8568A–SEEPR–11/08 8-Ultra Thin SAP Seal Year Top Mark Seal Year Seal Week Y = SEAL YEAR WW = SEAL WEEK 6: 2006 0: 2010 02 = Week 2 --- --- --- --- --- --- --- --- 7: 2007 1: 2011 04 = Week 4 A T M L H Y W W 8: 2008 2: 2012 :: : :::: : --- --- --- --- --- --- --- E C 50 = Week 50 Lot Number 52 = Week 52 --- --- --- --- --- --- --- --- Pin 1 Indicator (Dot) dBGA2 Top Mark 2ECU <--- Pin 1 This Corner Y = ONE DIGIT YEAR CODE 4: 2004 7: 2007 5: 2005 8: 2008 6: 2006 9: 2009 M = SEAL MONTH (USE ALPHA DESIGNATOR A-L) A = JANUARY B = FEBRUARY J = OCTOBER K = NOVEMBER L = DECEMBER TC = TRACE CODE
Figure 1. 8P3 – PDIP Notes: 1. This drawing is for general information only; refer to JEDEC D rawing MS-001, Variation BA, for additional information.
- Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3.
- D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not
- E and eA measured with the leads constrained to be perpendicular to datum.
- Pointed or rounded lead tips are pre ferred to ease insertion.
- b2 and b3 maximum dimensions do not include Dambar protrusions. Dambar protrusions shall not
4 PLCS
16 AT24C256C
0.100 BSC
0.300 BSC
Figure 2. 8S1 – JEDECSOIC DRAWING NO.1150 E. Cheyenne Mtn. Blvd.
18 AT24C256C
Figure 14. 8S2 - EIAJ SOIC Notes: 1. This drawing is for general information only; refer to EIAJ Drawing EDR-7320 for additional information.
- Mismatch of the upper and lower dies and resin burrs aren't included.
- It is recommended that upper and l ower cavities be equal. If they are different, the larger dimension shall be regarded.
- Determines the true geometric position.
41.27 BSC
Figure 15. 8U2-1 – dBGA2 d1 0.80 REF1. Dimension 'b' is measured at the maxi mum solder ball diamete r. This drawing is for general information only.
8 Solder Balls
DRAWING NO.1150 E. Cheyenne Mtn. Blvd.
20 AT24C256C
Figure 16. 8A2 – TSSOP
- Dimension D does not include mold Flash, prot rusions or gate burrs. Mold Flash, prot rusions and gate burrs shall not
exceed 0.15 mm (0.006 in) per sid e.
- Dimension E1 does not include inter-lead Flash or prot rusions. Inter-lead Flash and prot rusions shall not exceed
- Dimension b does not include Dambar prot rusion. Allowable Dambar prot rusion shall be 0.08 mm total in excess of the
between protrusion and adjacent lead is 0.07 mm .
- Dimension D and E1 to be dete rmined at Datum Plane H .
Figure 17. 8Y7 – SAP DRAWING NO.1150 E. Cheyeene Mtn. Blvd.
22 AT24C256C
8568A–SEEPR–11/08 Appendix A. Revision History Doc. Rev. Date Comments 8568A 11/2008 Initial document release
Headquarters International Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Room 1219 Chinachem Golden Plaza
77 Mody Road Tsimshatsui
Tel: (852) 2721-9778 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309
78054 Saint-Quentin-en-
9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Product Contact Web Site www.atmel.com Technical Support s_eeprom@atmel.com Sales Contact www.atmel.com/contacts Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or im plied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABI LITY WHATSOEVER AND DISC LAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LI ABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN-TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and pr oduct descriptions at any time without notice. Atmel do es not make any commitment to update the information contained herein. Unless specifically provided otherw ise, Atmel products are no t suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2008 Atmel Corporation. All rights reserv ed. Atmel®, Atmel logo and combinations ther eof, and others are registered trademark s or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. 8568A–SEEPR–11/08