AT24C256C_09 ATMEL
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 21
Technical content
Features
- Low-voltage and Standard-voltage Operation ⎯ VCC = 1.7V to 5.5V
- Internally Organized as 32,768 x 8
- Two-wire Serial Interface
- Schmitt Trigger, Filtered Inputs for Noise Suppression Two-wire Serial EEPROM 256K (32,768 x 8) AT24C256C Preliminary 8568A–SEEPR–9/09
- Bidirectional Data Transfer Protocol
- 1 MHz (5.0V, 2.7V, 2.5V), and 400 kHz (1.7V) Compatibility
- Write Protect Pin for Hardware and Software Data Protection
- 64-byte Page Write Mode (Partial Page Writes Allowed)
- Self-timed Write Cycle (5 ms Max)
- High Reliability ⎯ Endurance: One Million Write Cycles ⎯ Data Retention: 40 Years
- Lead-free/Halogen-free Devices Available
- 8-lead JEDEC SOIC, 8-lead UDFN, 8-lead TSSOP, and 8-ball VFBGA Packages
- Die Sales: Wafer Form, Waffle Pack and Bumped Wafers
Description
The AT24C256C provides 262,144 bits of serial electrically erasable and programmable read-only memory (EEPROM) organized as 32,768 words of 8 bits each. The device’s cascadable feature allows up to eight devices to share a common two-wire bus. The device is optimized for use in many industrial and commercial applications where low-power and low-volta ge operation are ess ential. The devices are available in space-saving 8-lead JEDEC SOIC, 8-lead UDFN, 8-lead TSSOP, and 8-ball VFBGA packages. In addition, this device operates from 1.7V to 5.5V. Table 1. Pin Configurations
2 AT24C256C [Preliminary]
Figure 1. Block Diagram
AT24C256C [Preliminary] 8568A–SEEPR–9/09 1. Pin Descriptions SERIAL CLOCK (SCL): The SCL input is used to positive-edge clock data into each EEPROM device and negative-edge clock data out of each device. SERIAL DATA (SDA): The SDA pin is bidirectional for serial data trans fer. This pin is open drain driven and may be wire-ORed with any number of other open-drain or open-collector devices. DEVICE/PAGE ADDRESSES (A2, A1, A0): The A2, A1, and A0 pins are device address inputs that are hardwired (directly to GND or to VCC) for compatibility with other AT24Cxx devices. When the pins are hardwired, as many as eight 256K devices may be addressed on a single bus system. (Device addressing is discussed in detail under “ Device Addressing”_Device_Addressing) A device is selected when a corresponding hardware and software match is true. If these pins are left floating, the A2, A1, and A0 pins will be internally pulled down to GND. However, due to capacitive coupling that may appear duri ng customer applications, Atmel recommends always connecting the address pins to a known state. When using a pull-up resistor, Atmel recommends using 10kΩ or less. WRITE PROTECT (WP): The write protect input, when connected to GND, allows normal write operations. When WP is connected directly to VCC, all write operations to the memory are inhibite d. If the pin is left floating, the WP pin will be internally pulled down to GND. However, due to capacit ive coupling that may appear during customer applications, Atmel recommends always connecting the WP pins to a known state. When using a pull-up resistor, Atmel recommends using 10kΩ or less.
4 AT24C256C [Preliminary]
addressing requires a 15-bit data word address. Table 2. Pin Capacitance Note: 1. This parameter is characterized and is not 100% tested. Table 3. DC Characteristics Note: 1. V IL min and VIH max are reference only and are not tested.
Table 4. AC Characteristics (Industrial Temperature) TAI = − 40°C to +85°C, VCC = +1.7V to +5.5V, CL = 100 pF (unless otherwise noted). Test conditions are listed in Note 2. Note: 1. This parameter is ensured by characterization and is not 100% tested.
- AC measurement conditions:
6 AT24C256C [Preliminary]
start or stop condition as defined below. Figure 2. Data Validity command (refer to Figure 3). Figure 3. Start and Stop Definition command will place the EEPROM in a standby power mode (refer to Figure 3). EEPROM sends a “0” during the ninth clock cycle to acknowledge that it has received each word. receipt of the stop bit and the completion of any internal operations.
8 AT24C256C [Preliminary]
Figure 7. Output Acknowledge
most significant bits as shown. This is common to all two-wire EEPROM devices. Figure 8. Device Addressing circuit that biases them to a logic low condition if the pins are allowed to float. and a write operation is initiated if this bit is low. whole memory when the WP pin is at VCC.
10 AT24C256C [Preliminary]
EEPROM will not respond until the write is complete (refer to Figure 9). Figure 9. Byte Write PAGE WRITE: The 256K EEPROM is capable of 64-byte page writes. microcontroller must terminate the page write sequence with a stop condition (refer to Figure 10). Figure 10. Page Write respond with a “0”, allowing the read or write sequence to continue.
12 AT24C256C [Preliminary]
following stop condition (refer to Figure 13). Figure 13. Sequential Read
AT24C256C [Preliminary] 8568A–SEEPR–9/09 7. Ordering Information 7.1. Ordering Code Detail Atmel Designator Product Family Device Density Device Revision Shipping Carrier Option Operating Voltage Package Option 256 = 256K B or blank = Bulk (tubes) T = Tape and reel L = 1.7V to 5.5V SS = JEDEC SOIC X= T S S O P MA = UDFN W = wafer WT = die in tape and reel C= U F B G A Package Device Grade or Wafer/Die Thickness H = Green, NiPdAu lead finish, Industrial Temperature Rang e (-40°C to +85°C) U = Green, matte Sn lead finish, Industrial Temperature Rang e (-40°C to +85°C) 11 = 11mil wafer thickness AT24C256C-SSHL-B 7.2. AT24C256C Ordering Codes Ordering Code Voltage Package Operating Range AT24C256C-SSHL-B (1) AT24C256C-SSHL-T (2) AT24C256C-XHL-B (1) AT24C256C-XHL-T (2) AT24C256C-MAHL-T (2) AT24C256C-CUL-T (2) 1.7V to 5.5V 1.7V to 5.5V 1.7V to 5.5V 1.7V to 5.5V 1.7V to 5.5V 1.7V to 5.5V 8S1 8S1 8A2 8A2 8MA2 8U2-1 Lead-free/Halogen-free Industrial Temperature (−40°C to 85°C) AT24C256C-W11 (3) 1.7V to 5.5V Die Sale Industrial Temperature (−40°C to 85°C) Note: 1. “-B” denotes bulk. 2. “-T” denotes tape & reel. SOIC = 4K per reel. TSSOP, VFBGA and UDFN = 5K per reel. 3. Bumped die available upon request. Contact Atmel Marketing. Package Type 8S1 8-lead, 0.150” Wide, Plastic Gull Wing Small Outline Package (JEDEC SOIC) 8A2 8-lead, 4.40mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) 8MA2 8-lead, 2.00 mm x 3.00 mm Body, 0.50 mm Pitch, Dual No Lead Package (UDFN) 8U2-1 8-ball, die Ball Grid Array Package (VFBGA)
14 AT24C256C [Preliminary]
8568A–SEEPR–9/09 8. Part Marketing Scheme AT24C256C-SSHL Top Mark Seal Year Seal Week Y = SEAL YEAR WW = SEAL WEEK 6: 2006 0: 2010 02 = Week 2 --- --- --- --- --- --- --- --- 04 = Week 4 7: 2007 1: 2011 A T M L H Y W W --- --- --- --- --- --- --- E C 50 = Week 50 Lot Number 52 = Week 52 --- --- --- --- --- --- --- --- Lot Number to Use ALL Characters in Marking BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark AT24C256C-XHL Top Mark Pin 1 Indicator (Dot) Y = SEAL YEAR WW = SEAL WEEK 6: 2006 0: 2010 02 = Week 2 --- --- --- --- 7: 2007 1: 2011 04 = Week 4 W --- --- --- --- E C 50 = Week 50 --- Bottom Mark XX = Country of Origin --- --- --- --- --- --- --- X X A A A A A A A Pin 1 Indicator AT24C256C-MAHL Seal Year Top Mark Seal Year Seal Week Y = SEAL YEAR WW = SEAL WEEK 6: 2006 0: 2010 02 = Week 2 --- --- --- --- --- --- --- --- 7: 2007 1: 2011 04 = Week 4 A T M L H Y W W --- --- --- --- --- --- --- E C 50 = Week 50 Lot Number 52 = Week 52 --- --- --- --- --- --- --- --- Pin 1 Indicator (Dot)
AT24C256C [Preliminary] 8568A–SEEPR–9/09 AT24C256C-CUL Top Mark 2ECU <--- Pin 1 This Corner Y = ONE DIGIT YEAR CODE 4: 2004 7: 2007 5: 2005 8: 2008 6: 2006 9: 2009 M = SEAL MONTH (USE ALPHA DESIGNATOR A-L) A = JANUARY B = FEBRUARY J = OCTOBER K = NOVEMBER L = DECEMBER TC = TRACE CODE
16 AT24C256C [Preliminary]
Figure 1. 8S1 – JEDECSOIC DRAWING NO.1150 E. Cheyenne Mtn. Blvd.
Figure 14. 8A2 – TSSOP
- Dimension D does not include mold Flash, prot rusions or gate burrs. Mold Flash, prot rusions and gate burrs shall not
exceed 0.15 mm (0.006 in) per sid e.
- Dimension E1 does not include inter-lead Flash or prot rusions. Inter-lead Flash and prot rusions shall not exceed
- Dimension b does not include Dambar prot rusion. Allowable Dambar prot rusion shall be 0.08 mm total in excess of the
between protrusion and adjacent lead is 0.07 mm .
- Dimension D and E1 to be dete rmined at Datum Plane H .
18 AT24C256C [Preliminary]
Figure 15. 8MA2 – UDFN
Figure 16. 8U2-1 – VFBGA
- Dimension 'b' is measured at the maxi mum solder ball diameter.
- This drawing is for general information.
20 AT24C256C [Preliminary]
8568A–SEEPR–9/09 Appendix A. Revision History Doc. Rev. Date Comments 8568A 09/2009 Initial document release
Headquarters International Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Room 1219 Chinachem Golden Plaza
77 Mody Road Tsimshatsui
Tel: (852) 2721-9778 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309
78054 Saint-Quentin-en-
9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Product Contact Web Site www.atmel.com Technical Support s_eeprom@atmel.com Sales Contact www.atmel.com/contacts Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or im plied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABI LITY WHATSOEVER AND DISC LAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LI ABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN-TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completene ss of the contents of this document and reserves the right to make changes to specifications and pr oduct descriptions at any time without notice. Atmel do es not make any commitment to update the information contained herein. Unless specifically provided otherw ise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2009 Atmel Corporation. All rights reserv ed. Atmel®, Atmel logo and combinations ther eof, and others are registered trademark s or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. 8568A–SEEPR–9/09