AT24C256B ATMEL
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 18
Technical content
Features
- Low-voltage and Standard-voltage Operation – 1.8 (V CC = 1.8V to 3.6V) Internally Organized as 32,768 x 8 Two-wire Serial Interface Schmitt Trigger, Filtered Inputs for Noise Suppression Bidirectional Data Transfer Protocol 1 MHz (3.6V , 2.7V, 2.5V), and 400 kHz (1.8V) Compatibility Write Protect Pin for Hardware and Software Data Protection 64-byte Page Write Mode (Partial Page Writes Allowed) Self-timed Write Cycle (5 ms Max) High Reliability – Endurance: One Million Write Cycles – Data Retention: 40 Years Extended Temperature and Lead-free/Halogen-free Devices Available 8-lead JEDEC PDIP, 8-lead JEDEC SOIC, 8-lead MAP , 8-lead TSSOP, and 8-ball dBGA2 TM Packages
Description
The AT24C256B provides 262,144 bits of serial electrically erasable and programma- ble read-only memory (EEPROM) organized as 32,768 words of 8 bits each. The device’s cascadable feature allows up to eight devices to share a common two-wire bus. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. The devices are available in space-saving 8-lead JEDEC PDIP , 8-lead JEDEC SOIC, 8-lead MAP , 8-lead TSSOP , and 8-ball dBGA2 packages. In addition, the entire family is available in a 1.8V (1.8V to 3.6V) version. Two-wire Serial EEPROM 256K (32,768 x 8) AT24C256B Preliminary Rev. 5080A–SEEPR–9/04 Table 1. Pin Configurations
2 AT24C256B
Figure 1. Block Diagram
5080A–SEEPR–9/04 Pin Description SERIAL CLOCK (SCL): The SCL input is used to positive-edge clock data into each EEPROM device and negative-edge clock data out of each device. SERIAL DATA (SDA): The SDA pin is bidirectional for serial data transfer. This pin is open- drain driven and may be wire-ORed with any number of other open-drain or open-collector devices. DEVICE/PAGE ADDRESSES (A2, A1, A0): The A2, A1, and A0 pins are device address inputs that are hardwired (directly to GND or to Vcc) for compatibility with other AT24Cxx devices. When the pins are hardwired, as many as eight 256K devices may be addressed on a single bus system. (Device addressing is discussed in detail under “Device Addressing,” page 8.) A device is selected when a corresponding hardware and software match is true. If these pins are left floating, the A2, A1, and A0 pins will be internally pulled down to GND. How- ever, due to capacitive coupling that may appear during customer applications, Atmel recommends always connecting the address pins to a known state. When using a pull-up resistor, Atmel recommends using 10k Ω or less. WRITE PROTECT (WP): The write protect input, when connected to GND, allows normal write operations. When WP is connected directly to Vcc, all write operations to the memory are inhibited. If the pin is left floating, the WP pin will be internally pulled down to GND. However, due to capacitive coupling that may appear during customer applications, Atmel recommends always connecting the WP pins to a known state. When using a pull-up resistor, Atmel recom- mends using 10kΩ or less. Memory Organization AT24C256B, 256K SERIAL EEPROM: The 256K is internally organized as 512 pages of 64 bytes each. Random word addressing requires a 15-bit data word address.
4 AT24C256B
Table 1. Pin Capacitance(1) Note: 1. This parameter is characterized and is not 100% tested. Table 2. DC Characteristics Notes: 1. V IL min and VIH max are reference only and are not tested.
Table 3. AC Characteristics (Industrial Temperature) Notes: 1. This parameter is characterized and is not 100% tested.
- AC measurement conditions:
erwise noted). Test conditions are listed in Note 2.
6 AT24C256B
device. Data on the SDA pin may change only during SCL low time periods (see Figure 2). Data changes during SCL high periods will indicate a start or stop condition as defined below. Figure 2. Data Validity must precede any other command (see Figure 3). Figure 3. Start and Stop Definition edge that it has received each word. power-up and after the receipt of the stop bit and the completion of any internal operations.
8 AT24C256B
Figure 6. Output Acknowledge all two-wire EEPROM devices. Figure 7. Device Address if the pins are allowed to float. initiated if this bit is high, and a write operation is initiated if this bit is low. made, the device will retu rn to a standby state.
10 AT24C256B
current address read, random address read, and sequential read. Figure 10. Current Address Read acknowledged by the EEPROM, the microcontroller must generate another start condition. ing stop condition (see Figure 11). Figure 11. Random Read
with a “0” but does generate a following stop condition (see Figure 12). Figure 12. Sequential Read
12 AT24C256B
5080A–SEEPR–9/04 Ordering Code Package Operation Range A T24C256B-10PU-1.8 A T24C256BN-10SU-1.8 A T24C256BU2-10UU-1.8 A T24C256B-10TU-1.8 A T24C256BY1-10YU-1.8 8P3 8S1 8U2-1 8A2 8Y1 Lead-free/Halogen-free Industrial T emperature (−40°C to 85°C Package Type 8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline Package (JEDEC SOIC) 8U2-1 8-ball, die Ball Grid Array Package (dBGA2) 8A2 8-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) 8Y1 8-lead, 4.90 mm x 3.00 mm Body, Dual Footprint, Non-leaded, Miniature Array Package (MAP) Options −1.8 Low-voltage (1.8V to 3.6V)
5080A–SEEPR–9/04 Packaging Information 8P3 – PDIP
2325 Orchard Parkway
San Jose, CA 95131 TITLE DRAWING NO. R REV. 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) 01/09/02 8P3 B Notes: 1. Thi s drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA, for additional information. 2. Dimen sions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or ro unded lead tips are preferred to ease insertion. COMMON DIMENSIONS (Unit of Measure = inches) SYMBOL MIN NOM MAX NOTE D E e Lb2 b A2 A N eA c
4 PLCS
A – – 0.210 2 A2 0.115 0.1 30 0.195 b 0.014 0.01 8 0.022 5 b2 0.045 0.060 0.070 6 b3 0.0 30 0.0 39 0.045 6 c 0.00 8 0.010 0.014 D 0. 355 0. 365 0.400 3 D1 0.005 – – 3 E 0. 300 0. 310 0. 325 4 E1 0.240 0.250 0.2 80 3 e 0.100 B SC eA 0. 300 BSC 4 L 0.115 0.1 30 0.150 2 Top View Side View End View
14 AT24C256B
5080A–SEEPR–9/04 8S1 – JEDEC SOIC 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. Note: 10/7/03 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) 8S1 B COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. A 1.35 – 1.75 b 0.31 – 0.51 C 0.17 – 0.25 D 4.80 – 5.00 E1 3.81 – 3.99 E 5.79 – 6.20 e 1.27 BSC L 0.40 – 1.27 ∅ 0˚ – 8˚ Top View End View Side View e B D A N E C L
5080A–SEEPR–9/04 8U2-1 – dBGA2 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. PO8U2-1 A 6/24/03 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE 8U2-1, 8-ball, 2.35 x 3.73 mm Body, 0.75 mm pitch, Small Die Ball Grid Array Package (dBGA2) A 0. 81 0.91 1.00 A1 0.15 0.20 0.25 A2 0.40 0.45 0.50 b 0.25 0. 30 0. 35 1 D 2. 35 BSC E 3.73 BSC e 0.75 B SC e1 0.74 REF d 0.75 B SC d1 0. 80 REF 1. Dimension 'b' is measured at the maximum solder ball diameter. This drawing is for general information only. d A Side View Top View Bottom View
8 Solder Balls
A B C D (e1) e A1 BALL PAD CORNER (d1) 1. b DA1 BALL PAD CORNER E
16 AT24C256B
5080A–SEEPR–9/04 8A2 – TSSOP San Jose, CA 95131 TITLE DRAWING NO. R REV. 5/30/02 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 2.90 3.00 3.10 2, 5 E 6.40 BSC E1 4.30 4.40 4.50 3, 5 A – – 1.20 A2 0.80 1.00 1.05 b 0.19 – 0.30 4 e 0.65 BSC L 0.45 0.60 0.75 L1 1.00 REF 8A2, 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimension D and E1 to be determined at Datum Plane H. 8A2 B Side View End ViewTop View A L D 123 N b Pin 1 indicator this corner E e
5080A–SEEPR–9/04 8Y1 – MAP A – – 0.90 A1 0.00 – 0.05 D 4.70 4.90 5.10 E 2. 80 3.00 3.20 D1 0. 85 1.00 1.15 E1 0. 85 1.00 1.15 b 0.25 0. 30 0. 35 e 0.65 TYP L 0.50 0.60 0.70 PIN 1 INDEX AREA D E A A1 b 8 7 6 e L PIN 1 INDEX AREA 1 2 3 4 A Top View End View Bottom View Side View San Jose, CA 95131 TITLE DRAWING NO. R REV. 8Y1, 8-lead (4.90 x 3.00 mm Body) MSOP Array Package (MAP) Y1 C8Y1 2/28/03 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE
Printed on recycled paper. 5080A–SEEPR–9/04 Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standar d warranty which is detailed in Atmel’s T erms and Conditions located on the Company’s web site. The Company assumes no responsibi lity for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time wi thout notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not aut horized for use as critical components in life support devices or systems. Atmel Corporation Atmel Operations San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza
77 Mody Road Tsimshatsui
Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Memory San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 Microcontrollers San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602
44306 Nantes Cedex 3, France
13106 Rousset Cedex, France
1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 RF/Automotive Theresienstrasse 2 Postfach 3535
74025 Heilbronn, Germany
1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123
38521 Saint-Egreve Cedex, France
www.atmel.com/literature © Atmel Corporation 2004 . All rights reserved. Atmel ®, logo and combinations thereof are registered trademarks, and Everywhere Y ou Are SM and dBGA2 ™ are trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be the trademarks of others.