AT24C256B_08 ATMEL

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 24

Technical content

Features

  • Low-voltage and Standard-voltage Operation – 1.8 (V CC = 1.8V to 5.5V)
  • Internally Organized as 32,768 x 8
  • Two-wire Serial Interface
  • Schmitt Trigger, Filtered Inputs for Noise Suppression
  • Bidirectional Data Transfer Protocol
  • 1 MHz (5.0V, 2.7V, 2.5V), and 400 kHz (1.8V) Compatibility
  • Write Protect Pin for Hardware and Software Data Protection
  • 64-byte Page Write Mode (Partial Page Writes Allowed)
  • Self-timed Write Cycle (5 ms Max)
  • High Reliability – Endurance: One Million Write Cycles – Data Retention: 40 Years
  • Lead-free/Halogen-free Devices Available
  • 8-lead JEDEC PDIP, 8-lead JEDEC SOIC, EIAJ SOIC, 8-lead Ultra Thin Small Array Package (SAP), 8-lead TSSOP , and 8-ball dBGA2 Packages
  • Die Sales: Wafer Form, Waffle Pack and Bumped Wafers

Description

The AT24C256B provides 262,144 bits of serial electrically erasable and programma- ble read-only memory (EEPROM ) organized as 32,768 wo rds of 8 bits each. The device’s cascadable feature allows up to eight devices to share a common two-wire bus. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. The devices are available in space-saving 8-lead JEDEC PDIP, 8-lead JEDEC SOIC , 8-lead Ultra Thin SAP, 8- lead TSSOP, and 8-ball dBGA2 packages. In add ition, the entire family is available in a 1.8V (1.8V to 5.5V) version. Two-wire Serial EEPROM 256K (32,768 x 8) AT24C256B Rev. 5279B–SEEPR–3/08 Pin Configurations Pin Name Function A0–A2 Address Inputs SDA Serial Data SCL Serial Clock Input WP Write Protect GND Ground GND VCC WP SCL SDA VCC WP SCL SDA GND VCC WP SCL SDA GND 8-lead PDIP 8-lead SOIC 8-lead dBGA2 Bottom View VCC WP SCL SDA GND 8-lead Ultra Thin SAP Bottom View GND VCC WP SCL SDA 8-lead TSSOP

5279B–SEEPR–3/08 AT24C256B Figure 1-1. Block Diagram 1. Absolute Maximum Ratings* Maximum Ratings” may cause permanent dam- age to the device. This is a stress rating only; functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Voltage on Any Pin START STOP LOGIC VCC GND WP SCL SDA SERIAL CONTROL LOGIC EN H.V. PUMP/TIMING EEPROM DATA RECOVERY SERIAL MUX X DEC DOUT/ACK LOGIC COMP LOAD INC DATA WORD ADDR/COUNTER Y DEC R/W DOUT DIN LOAD DEVICE ADDRESS COMPARATOR

5279B–SEEPR–3/08 AT24C256B 2. Pin Description SERIAL CLOCK (SCL): The SCL input is used to positive-edge clock data into each EEPROM device and negative-edge clock data out of each device. SERIAL DATA (SDA): The SDA pin is bidirectional for seri al data transfer. This pin is open- drain driven and may be wire-ORed with any number of other open-drain or open-collector devices. DEVICE/PAGE ADDRESSES (A2, A1, A0): The A2, A1, and A0 pins are device address inputs that are hardwired (directly to GND or to Vcc) for compatibility with other AT24Cxx devices. When the pins are hardwired, as many as eight 256K devices may be addressed on a single bus system. (Device addressing is discussed in detail under “Device Addressing,” page 9.) A device is selected when a corresponding hardware and softwa re match is true. If these pins are left floating, the A2, A1, and A0 pins will be interna lly pulled down to GND. However, due to capaci- tive coupling that may appear during cust omer applications, Atmel recommends always connecting the address pins to a known state. When using a pull-up resistor, Atmel recommends using 10kΩ or less. WRITE PROTECT (WP): The write protect input, when connec ted to GND, allows normal write operations. When WP is connected directly to Vcc, all write operations to the memory are inhib- ited. If the pin is left floating, the WP pin will be internal ly pulled down to GND. However, due to capacitive coupling that may appear during customer applications, Atmel recommends always connecting the WP pins to a known state. When using a pull-up resistor, Atmel recommends using 10kΩ or less. 3. Memory Organization AT24C256B, 256K SERIAL EEPROM: The 256K is internally organized as 512 pages of 64 bytes each. Random word addressing requires a 15-bit data word address. Note: 1. This parameter is characterized and is not 100% tested. Table 3-1. Pin Capacitance(1) Applicable over recommended operating range from TA = 25°C, f = 1.0 MHz, VCC = +1.8V Symbol Test Condition Max Units Conditions CI/O Input/Output Capacitance (SDA) 8 pF V I/O = 0V CIN Input Capacitance (A0, A1, SCL) 6 pF V IN = 0V

5279B–SEEPR–3/08 AT24C256B Notes: 1. V IL min and VIH max are reference only and are not tested. Table 3-2. DC Characteristics Applicable over recommended operating range from: TAI = − 40°C to +85°C, VCC = +1.8V to +5.5V (unless otherwise noted) Symbol Parameter Test Co ndition Min Typ Max Units VCC1 Supply Voltage 1.8 5.5 V ICC1 Supply Current V CC = 5.0V READ at 400 kHz 1.0 2.0 mA ICC2 Supply Current V CC = 5.0V WRITE at 400 kHz 2.0 3.0 mA ISB1 Standby Current (1.8V option) VCC = 1.8V VIN = VCC or VSS 1.0 µA VCC = 5.0V 6.0 µA ILI Input Leakage Current VCC = 5.0V VIN = VCC or VSS 0.10 3.0 µA ILO Output Leakage Current VCC = 5.0V VOUT = VCC or VSS 0.05 3.0 µA VIL Input Low Level(1) − 0.6 V CC x 0.3 V VIH Input High Level(1) VCC x 0.7 V CC + 0.5 V VOL2 Output Low Level V CC = 3.0V I OL = 2.1 mA 0.4 V VOL1 Output Low Level V CC = 1.8V I OL = 0.15 mA 0.2 V

5279B–SEEPR–3/08 AT24C256B Notes: 1. This parameter is ensured by ch aracterization and is not 100% tested. 2. AC measurement conditions: RL (connects to VCC): 1.3 kΩ (2.5V, 5.5V), 10 kΩ (1.8V) Input pulse voltages: 0.3 VCC to 0.7 VCC Input rise and fall times: ≤ 50 ns Input and output timing reference voltages: 0.5 VCC Table 3-3. AC Characteristics (Industrial Temperature) Applicable over recommended operating range from TAI = − 40°C to +85°C, VCC = +1.8V to +5.5V, CL = 100 pF (unless oth- erwise noted). Test conditions are listed in Note 2. Symbol Parameter 1.8-volt 2.5, 5.0-volt UnitsMin Max Min Max fSCL Clock Frequency, SCL 400 1000 kHz tLOW Clock Pulse Width Low 1.3 0.4 µs tHIGH Clock Pulse Width High 0.6 0.4 µs ti Noise Suppression Time(1) 100 50 ns tAA Clock Low to Data Out Valid 0.05 0.9 0.05 0.55 µs tBUF Time the bus must be free before a new transmission can start(1) 1.3 0.5 µs tHD.STA Start Hold Time 0.6 0.25 µs tSU.STA Start Set-up Time 0.6 0.25 µs tHD.DAT Data In Hold Time 0 0 µs tSU.DAT Data In Set-up Time 100 100 ns tR Inputs Rise Time(1) 0.3 0.3 µs tF Inputs Fall Time(1) 300 100 ns tSU.STO Stop Set-up Time 0.6 0.25 µs tDH Data Out Hold Time 50 50 ns tWR Write Cycle Time 5 5 ms Endurance(1) 25°C, Page Mode, 3.3V 1,000,000 Write Cycles

5279B–SEEPR–3/08 AT24C256B Figure 4-6. Output Acknowledge SCL DATA IN DATA OUT START ACKNOWLEDGE 981

5279B–SEEPR–3/08 AT24C256B 5. Device Addressing The 256K EEPROM requires an 8-bi t device address word following a start condition to enable the chip for a read or write operation (see Figure 5-1). The device address word consists of a mandatory “1”, “0” sequence for the first four most sign ificant bits as shown. This is common to all two-wire EEPROM devices. Figure 5-1. Device Address The next three bits are the A2, A1, A0 device ad dress bits to allow as many as eight devices on the same bus. These bits must compare to their corresponding hardwired input pins. The A2, A1, and A0 pins use an internal proprietary circuit that biases them to a logic low condition if the pins are allowed to float. The eighth bit of the device address is the read/write operation select bit. A read operation is ini- tiated if this bit is high, and a write operation is initiated if this bit is low. Upon a compare of the device address, the EEPROM will output a “0”. If a compare is not made, the device will return to a standby state. DATA SECURITY: The AT24C256B has a hardware data protection scheme that allows the user to write protect the whole memory when the WP pin is at VCC. MSB 1 0 1 0 A2 A1 A0 R/W LSB

5279B–SEEPR–3/08 AT24C256B SEQUENTIAL READ: Sequential reads are initiated by either a current address read or a ran- dom address read. After the microcontroller receives a data word, it responds with an acknowledge. As long as the EEPROM receives an acknowledge, it will continue to increment the data word address and serially clock out sequential data words. When the memory address limit is reached, the data word address will “roll over” and the sequential read will continue. The sequential read operation is terminated when the microcontroller does not respond with a “0” but does generate a following stop condition (see Figure 7-3). Figure 7-3. Sequential Read

5279B–SEEPR–3/08 AT24C256B 8. AT24C256B Ordering Codes Notes: 1. “-B” denotes bulk. 3. Available in tape & reel and wafer form; order as SL788 for inkless wafer form. Bumped die available upon request. Please contact Serial Interface Marketing. Ordering Code Voltage Package Operation Range AT24C256B-PU (Bulk Form Only) AT24C256BN-SH-B(1) (NiPdAu Lead Finish) AT24C256BN-SH-T(2) (NiPdAu Lead Finish) AT24C256BW-SH-B(1) (NiPdAu Lead Finish) AT24C256BW-SH-T(2) (NiPdAu Lead Finish) AT24C256B-TH-B(1) (NiPdAu Lead Finish) AT24C256B-TH-T(2) (NiPdAu Lead Finish) AT24C256BY7-YH-T(2) (NiPdAu Lead Finish) AT24C256BU2-UU-T(2) 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 8P3 8S1 8S1 8S2 8S2 8A2 8A2 8Y7 8U2-1 Lead-free/Halogen-free Industrial Temperature (−40°C to 85°C) AT24C256B-W-11 1.8 Die Sale Industrial Temperature (−40°C to 85°C) Package Type 8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline Package (JEDEC SOIC) 8S2 8-lead, 0.200” Wide, Plastic Gull Wing Small Outline Package (EIAJ SOIC) 8U2-1 8-ball, die Ball Grid Array Package (dBGA2) 8A2 8-lead, 4.40 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) 8Y7 8-lead, 6.00 mm x 4.90 mm Body, Ultra Thin, Dual Footprint, Non-leaded, Small Array Package (SAP) Options −1.8 Low-voltage (1.8V to 5.5V)

5279B–SEEPR–3/08 AT24C256B 9. Part Marking Scheme 8-PDIP 8-SOIC TOP MARK Seal Year Y = SEAL YEAR WW = SEAL WEEK | Seal Week 6: 2006 0: 2010 02 = Week 2 | | | 7: 2007 1: 2011 04 = Week 4 A T M L U Y W W 9: 2009 3: 2013 :: : :::: ::

2 E B 1 52 = Week 52

  • Lot Number Lot Number to Use ALL Characters in Marking | BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark TOP MARK Seal Year Y = SEAL YEAR WW = SEAL WEEK | Seal Week 6: 2006 0: 2010 02 = Week 2 | | | 7: 2007 1: 2011 04 = Week 4 A T M L H Y W W 9: 2009 3: 2013 :: : :::: ::
  • Lot Number Lot Number to Use ALL Characters in Marking | BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark

5279B–SEEPR–3/08 AT24C256B 8-TSSOP 8-Ultra Thin SAP TOP MARK Pin 1 Indicator (Dot) Y = SEAL YEAR WW = SEAL WEEK | 6: 2006 0: 2010 02 = Week 2

2 E B 1 50 = Week 50

BOTTOM MARK XX = Country of Origin X X A A A A A A A <- Pin 1 Indicator TOP MARK Seal Year | Seal Week Y = SEAL YEAR WW = SEAL WEEK | | | 6: 2006 0: 2010 02 = Week 2 A T M L H Y W W 8: 2008 2: 2012 :: : :::: : Pin 1 Indicator (Dot)

5279B–SEEPR–3/08 AT24C256B dBGA2 TOP MARK |<-- Pin 1 This Corner Y = ONE DIGIT YEAR CODE 4: 2004 7: 2007 5: 2005 8: 2008 6: 2006 9: 2009 M = SEAL MONTH (USE ALPHA DESIGNATOR A-L) A = JANUARY B = FEBRUARY J = OCTOBER K = NOVEMBER L = DECEMBER TC = TRACE CODE

5279B–SEEPR–3/08 AT24C256B 10. Packaging Information 8P3 – PDIP

2325 Orchard Parkway

San Jose, CA 95131 TITLE DRAWING NO. R REV. 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) 01/09/02 8P3 B Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA, for additional information . 2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion. COMMON DIMENSIONS (Unit of Measure = inches) SYMBOL MIN NOM MAX NOTE D E e L b2 b A2 A N eA c

4 PLCS

A – – 0.210 2 A2 0.115 0.130 0.195 b 0.014 0.018 0.022 5 b2 0.045 0.060 0.070 6 b3 0.030 0.039 0.045 6 c 0.008 0.010 0.014 D 0.355 0.365 0.400 3 D1 0.005 – – 3 E 0.300 0.310 0.325 4 E1 0.240 0.250 0.280 3 e 0.100 BSC eA 0.300 BSC 4 L 0.115 0.130 0.150 2 Top View Side View End View

5279B–SEEPR–3/08 AT24C256B 8S1 – JEDEC SOIC 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. Note: 10/7/03 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) 8S1 B COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. A 1.35 – 1.75 b 0.31 – 0.51 C 0.17 – 0.25 D 4.80 – 5.00 E1 3.81 – 3.99 E 5.79 – 6.20 e 1.27 BSC L 0.40 – 1.27 ∅ 0˚ – 8˚ Top View End View Side View e B D A N E C L

5279B–SEEPR–3/08 AT24C256B 8S2 - EIAJ SOIC San Jose, CA 95131 TITLE DRAWING NO. R REV. 8S2, 8-lead, 0.209" Body, Plastic Small Outline Package (EIAJ) 4/7/06 8S2 D COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE Notes: 1. This drawing is for general information only; refer to EIAJ Drawing EDR-7320 for additional information. 2. Mismatch of the upper and lower dies and resin burrs aren't included. 3. It is recommended that upper and lower cavities be equal. If they are different, the larger dimension shall be regarded. 4. Determines the true geometric position. A 1.70 2.16 A1 0.05 0.25 b 0.35 0.48 5 C 0.15 0.35 5 D 5.13 5.35 E1 5.18 5.40 2, 3 E 7.70 8.26 L 0.51 0.85 θ 0° 8° e 1.27 BSC 4 θθ NN EE CC E1E1 AA bb LL A1A1 ee DD TOP VIEW END VIEW SIDE VIEW

5279B–SEEPR–3/08 AT24C256B 8U2-1 – dBGA2 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. PO8U2-1 A 6/24/03 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE 8U2-1, 8-ball, 2.35 x 3.73 mm Body, 0.75 mm pitch, Small Die Ball Grid Array Package (dBGA2) A 0.81 0.91 1.00 A1 0.15 0.20 0.25 A2 0.40 0.45 0.50 b 0.25 0.30 0.35 1 D 2.35 BSC E 3.73 BSC e 0.75 BSC e1 0.74 REF d 0.75 BSC d1 0.80 REF 1. Dimension 'b' is measured at the maximum solder ball diameter. This drawing is for general information only. d A Side View Top View Bottom View

8 Solder Balls

A B C D (e1) e A1 BALL PAD CORNER (d1) 1. b DA1 BALL PAD CORNER E

5279B–SEEPR–3/08 AT24C256B 8A2 – TSSOP San Jose, CA 95131 TITLE DRAWING NO. R REV. 5/30/02 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 2.90 3.00 3.10 2, 5 E 6.40 BSC E1 4.30 4.40 4.50 3, 5 A – – 1.20 A2 0.80 1.00 1.05 b 0.19 – 0.30 4 e 0.65 BSC L 0.45 0.60 0.75 L1 1.00 REF 8A2, 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimension D and E1 to be determined at Datum Plane H. 8A2 B Side View End ViewTop View A L D 123 N b Pin 1 indicator this corner E e

5279B–SEEPR–3/08 AT24C256B 8Y7 – SAP 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. 8Y7, 8-lead (6.00 x 4.90 mm Body) Ultra-Thin SOIC Array Package (UTSAP) Y7 B8Y7 10/13/05 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A – – 0.60 A1 0.00 – 0.05 D 5.80 6.00 6.20 E 4.70 4.90 5.10 D1 3.30 3.40 3.50 E1 3.90 4.00 4.10 b 0.35 0.40 0.45 e 1.27 TYP e1 3.81 REF L 0.50 0.60 0.70 PIN 1 ID L b e PIN 1 INDEX AREA A E D A

5279B–SEEPR–3/08 AT24C256B

Revision History

Doc. Rev. Date Comments 5279B 3/2008 Format changes to document 5279A 1/2008 AT24C256B product with date code 2008 work week 14 (814) or later supports 5Vcc operation Initial document release

5279B–SEEPR–3/08 Headquarters International Atmel Corporation San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Room 1219 Chinachem Golden Plaza

77 Mody Road Tsimshatsui

Tel: (852) 2721-9778 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309

78054 Saint-Quentin-en-

9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Product Contact Web Site www.atmel.com Technical Support s_eeprom@atmel.com Sales Contact www.atmel.com/contacts Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection wi th Atmel products. No license, expr ess or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LI ABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTOR Y WARRANTY RELATING TO ITS PRODUCTS INCLUDING , BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICU LAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRE CT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR I NCIDEN- TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or comp leteness of the contents of th is document and reserves the rig ht to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained her ein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not int ended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2008 Atmel Corporation . All rights reserved. Atmel ®, logo and combinations thereof, and others, are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.