DATASHEET SEARCH SITE

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 23

Technical content

Atmel-8719B-SEEPROM-AT24C16C-Datasheet_042013 Standard Features  Low-voltage and standard-voltage operation  VCC = 1.7V to 5.5V  Internally organized as 2,048 x 8 (16K)  I2C-compatible (2-wire) serial interface  Schmitt Trigger, filtered inputs for noise suppression  Bidirectional data transfer protocol  1MHz (2.5V, 2.7V, 5V), 400kHz (1.7V) compatibility  Write Protect pin for hardware data protection  16-byte Page Write mode  Partial page writes allowed  Self-timed write cycle (5ms max)  High-reliability  Endurance: 1,000,000 write cycles  Data retention: 100 years  Green package options (Pb/Halide-free/RoHS compliant)  8-lead PDIP, 8-lead SOIC, 8-lead TSSOP, 8-pad UDFN, 8-pad XDFN, 5-lead SOT23, and 8-ball VFBGA  Die options: wafer form and tape and reel

Description

The Atmel® AT24C16C provides 16,384 bits of Serial Electrically Erasable and Programmable Read-Only Memory (EEPROM) organized as 2,048 words of eight bits each. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. AT24C16C is available in space-saving 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead TSSOP, 8-pad UDFN , 8-pad XDFN, 5-lead SOT23, and 8-ball VFBGA packages and is accessed via a 2-wire serial interface. Atmel AT24C16C I2C-Compatible, (2-Wire) Serial EEPROM 16-Kbit (2048 x 8) DATASHEET

  1. Pin Configurations and Pinouts

Table 1. Pin Configuration Note: Drawings are not to scale.

3Atmel AT24C16C [DATASHEET] Atmel-8719B-SEEPROM-AT24C16C-Datasheet_042013 3. Block Diagram 4. Pin Description Serial Clock (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative edge clock data out of each device. Serial Data (SDA): The SDA pin is bidirectional for serial data transfer. This pin is open-drain driven and may be wire-ORed with any number of other open-drain or open-collector devices. Device/Page Addresses: The AT24C16C does not use the device address pins, which limits the number of devices on a single bus to one (see Section 7. “Device Addressing” on page 9). Write Protect (WP): AT24C16C has a Write Protect pin that provides hardware data protection. The Write Protect pin allows normal Read/Write operations when connected to Ground (GND). When the Write Protect pin is connected to VCC, the Write Protection feature is enabled and operates as shown in Table 4-1. Table 4-1. Write Protect Start Stop Logic Data Word ADDR/Counter Row Decoder Device Address Comparator Data Latches DOUT / ACK Logic Column Decoder EEPROM Array Serial Control Logic High Voltage Pump & Timing Serial MUX Read/Write Enable COMP Load INC VCC GND WP SCL SDA DOUT DIN WP Pin Status Part of the Array Protected AT24C16C At VCC Full Array At GND Normal Read/Write Operations

4Atmel AT24C16C [DATASHEET] Atmel-8719B-SEEPROM-AT24C16C-Datasheet_042013 5. Memory Organization AT24C16C, 16K Serial EEPROM: Internally organized with 128 pages of 16 bytes each, the 16K requires a 11-bit data word address for random word addressing. Table 5-1. Pin Capacitance (1) Note: 1. This parameter is characterized and is not 100% tested. Table 5-2. DC Characteristics Note: 1. V IL min and VIH max are reference only and are not tested. Applicable over recommended operating range from TA = 25°C, f = 1.0MHz, VCC = 5.5V. Symbol Test Condition Max Units Conditions CI/O Input/Output capacitance (SDA) 8 pF VI/O = 0V CIN Input capacitance (A0, A1, A2, SCL) 6 pF VIN = 0V Applicable over recommended operating range from: TAI = -40°C to +85°C, VCC = 1.7V to 5.5V (unless otherwise noted). Symbol Parameter Test Condition Min Typ Max Units VCC1 Supply Voltage 1.7 5.5 V ICC Supply Current VCC = 5.0V Read at 100kHz 0.4 1.0 mA ICC Supply Current VCC = 5.0V Write at 100kHz 2.0 3.0 mA ISB1 Standby Current VCC = 1.7V VIN = VCC or VSS 1.0 μA ISB2 Standby Current VCC = 5.5V VIN = VCC or VSS 6.0 μA ILI Input Leakage Current VIN = VCC or VSS 0.10 3.0 μA ILO Output Leakage Current VOUT = VCC or VSS 0.05 3.0 μA VIL Input Low Level(1) –0.6 VCC x 0.3 V VIH Input High Level(1) VCC x 0.7 VCC + 0.5 V VOL2 Output Low Level VCC = 3.0V IOL = 2.1mA 0.4 V VOL1 Output Low Level VCC = 1.7V IOL = 0.15mA 0.2 V

5Atmel AT24C16C [DATASHEET] Atmel-8719B-SEEPROM-AT24C16C-Datasheet_042013 Table 5-3. AC Characteristics Note: 1. This parameter is ensured by characterization only. Applicable over recommended operating range from TAI = -40C to 85C, VCC = +1.7V to 5.5V, CL = 1TTL Gate and 100pF (unless otherwise noted). Symbol Parameter UnitsMin Max Min Max fSCL Clock Frequency, SCL 400 1000 kHz tLOW Clock Pulse Width Low 1.2 0.4 μs tHIGH Clock Pulse Width High 0.6 0.4 μs tI Noise Suppression Time 100 50 ns tAA Clock Low to Data Out Valid 0.1 0.9 0.05 0.55 μs tBUF Time the bus must be free before a new transmission can start. 1.2 0.5 μs tHD.STA Start Condition Hold Time 0.6 0.25 μs tSU.STA Start Condiition Setup Time 0.6 0.25 μs tHD.DAT Data In Hold Time 0 0 μs tSU.DAT Data In Setup Time 100 100 ns tR Inputs Rise Time(1) 0.3 0.3 μs tF Inputs Fall Time(1) 300 100 ns tSU.STO Stop Condition Setup Time 0.6 .25 μs tDH Data Out Hold Time 50 50 ns tWR Write Cycle Time 5 5 ms Endurance(1) 3.3V, 25C, Page Mode 1,000,000 Write Cycles

6Atmel AT24C16C [DATASHEET] Atmel-8719B-SEEPROM-AT24C16C-Datasheet_042013 6. Device Operation Clock and Data Transitions: The SDA pin is normally pulled high with an external device. Data on the SDA pin may change only during SCL low time periods (see Figure 6-4 on page 8). Data changes during SCL high periods will indicate a Start or Stop Condition as defined below. Start Condition: A high-to-low transition of SDA with SCL high is a Start Condition which must precede any other command (see Figure 6-5 on page 8). Stop Condition: A low-to-high transition of SDA with SCL high is a Stop Condition. After a read sequence, the Stop Condition command will place the EEPROM in a standby power mode (see Figure 6-5 on page 8). Acknowledge: All addresses and data words are serially transmitted to and from the EEPROM in eight bit words. The EEPROM sends a zero to acknowledge that it has received each word. This happens during the ninth clock cycle. Standby Mode: The AT24C16C features a low-power standby mode which is enabled:  Upon power-up.  After the receipt of the Stop Condition and the completion of any internal operations. 2-wire Software Reset: After an interruption in protocol, power loss or system reset, any 2-wire part can be reset by following these steps: 1. Create a Start Condition, 2. Clock nine cycles, 3. Create another Start Condition followed by Stop Condition as shown below. The device is ready for next communication after above steps have been completed. Figure 6-1. Software Reset SCL 9 Start Condition Start Condition Stop Condition 8321 SDA Dummy Clock Cycles

12Atmel AT24C16C [DATASHEET] Atmel-8719B-SEEPROM-AT24C16C-Datasheet_042013 10. Ordering Code Detail Atmel Designator Product Family Device Density Device Revision Shipping Carrier Option Operating Voltage 16 = 16K 24C = Standard Serial EEPROM B or blank = Bulk (Tubes) T = Tape and Reel M = 1.7V to 5.5V Package Device Grade or Wafer/Die Thickness H = Green, NiPdAu Lead Finish, Industrial Temperature Range (-40˚C to +85˚C) U = Green, Matte Sn Lead Finish, Industrial Temperature Range (-40˚C to +85˚C) 11 = 11mil Wafer Thickness Package Option P = PDIP SS = JEDEC SOIC X = TSSOP MA = UDFN ME = XDFN ST = SOT23 C = VFBGA WWU = Wafer Unsawn AT24C16C-SSHM-B

13Atmel AT24C16C [DATASHEET] Atmel-8719B-SEEPROM-AT24C16C-Datasheet_042013 11. Product Markings DRAWING NO. REV. TITLE 24C16CSM D 7/8/13 DL-CSO-Assy_eng@atmel.com AAAAAAAA###% @ATMLHYWW 8-lead SOIC 8-lead TSSOP AAAAAAA ###% @ ATHYWW 1.5 x 2.0 mm Body 8-ball VFBGA PIN 1 ###U YMXX ### YXX 8-pad XDFN 1.8 x 2.2 mm Body 8-pad UDFN ### H%@ YXX 2.0 x 3.0 mm Body Note 2: Package drawings are not to scale Note 1: designates pin 1 AT24C16C: Package Marking Information Catalog Number Truncation AT24C16C Truncation Code ###: 16C Date Codes Voltages Y = Year M = Month WW = Work Week of Assembly % = Minimum Voltage 3: 2013 7: 2017 A: January 02: Week 2 M: 1.7V min 4: 2014 8: 2018 B: February 04: Week 4 6: 2016 0: 2020 L: December 52: Week 52 Country of Assembly Lot Number Grade/Lead Finish Material @ = Country of Assembly AAA...A = Atmel Wafer Lot Number H: Industrial/NiPdAu U: Industrial/Matte Tin/SnAgCu Trace Code Atmel Truncation XX = Trace Code (Atmel Lot Numbers Correspond to Code) AT: Atmel Example: AA, AB.... YZ, ZZ ATM: Atmel ATML: Atmel ###%U YMXX Bottom Mark Top Mark 5-lead SOT-23 AAAAAAAA ###% @ATMLUYWW 8-lead PDIP

14Atmel AT24C16C [DATASHEET] Atmel-8719B-SEEPROM-AT24C16C-Datasheet_042013 12. Ordering Codes

12.1 AT24C16C Ordering Information

Notes: 1. B = Bulk 2. T = Tape and Reel  SOIC = 4K per reel  TSSOP, UDFN, XDFN, SOT23, and VFBGA = 5K per reel 3. For Wafer sales, please contact Atmel Sales. Atmel Ordering Code Lead Finish Package Voltage Operation Range AT24C16C-PUM Bulk Form Only (Lead-free/Halogen-free) 8P3 1.7V to 5.5V Industrial Temperature (–40C to 85C) AT24C16C-SSHM-B(1) NiPdAu (Lead-free/Halogen-free) 8S1 AT24C16C-SSHM-T(2) AT24C16C-XHM-B(1) AT24C16C-XHM-T(2) AT24C16C-MAHM-T(2) 8MA2 AT24C16C-MEHM-T(2) — 8ME1 AT24C16C-STUM-T(2) Matte Sn (Lead-free/Halogen-free) 5TS1 AT24C16C-CUM-T(2) SnAgCu (Lead-free/Halogen-free) 8U3-1 AT24C16C-WWU11M(3) — Wafer Sale Package Type 8P3 8-lead, 0.300" wide, Plastic Dual Inline (PDIP) 8S1 8-lead, 0.150" wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8X 8-lead, 4.40mm body, Plastic Thin Shrink Small Outline (TSSOP) 8MA2 8-pad, 2.00mm x 3.00mm body, 0.50mm pitch, Plastic Ultra Thin Dual Flat No Lead (UDFN) 8ME1 8-lead, 1.80mm x 2.20mm body, 0.40mm pitch, Extra Thin Dual Flat No Lead (XDFN) 5TS1 5-lead, 2.90mm x 1.60mm body, Plastic Thin Shrink Small Outline (SOT23) 8U3-1 8-ball, 1.50mm x 2.00mm body, 0.50mm pitch, Die Ball Grid Array (VFBGA)

15Atmel AT24C16C [DATASHEET] Atmel-8719B-SEEPROM-AT24C16C-Datasheet_042013 13. Packaging Information 8P3 — 8-lead PDIP DRAWING NO. REV. TITLE GPC Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information. 2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion. COMMON DIMENSIONS (Unit of Measure = inches) SYMBOL MIN NOM MAX NOTE D E e Lb2 b A2 A N eA c

4 PLCS

A 0.210 2 A2 0.115 0.130 0.195 b 0.014 0.018 0.022 5 b2 0.045 0.060 0.070 6 b3 0.030 0.039 0.045 6 c 0.008 0.010 0.014 D 0.355 0.365 0.400 3 D1 0.005 3 E 0.300 0.310 0.325 4 E1 0.240 0.250 0.280 3 e 0.100 BSC eA 0.300 BSC 4 L 0.115 0.130 0.150 2 Top View Side View End View Package Drawing Contact: packagedrawings@atmel.com 8P3 D 06/21/11 8P3, 8-lead, 0.300” Wide Body, Plastic Dual In-line Package (PDIP) PTC

16Atmel AT24C16C [DATASHEET] Atmel-8719B-SEEPROM-AT24C16C-Datasheet_042013 13.1 8S1 — 8-leadJEDEC SOIC DRAWING NO. REV. TITLE GPC COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 A 1.35 – 1.75 b 0.31 – 0.51 C 0.17 – 0.25 D 4.80 – 5.05 E1 3.81 – 3.99 E 5.79 – 6.20 e 1.27 BSC L 0.40 – 1.27 ØØ 0° – 8° Ø E N TOP VIEW C END VIEW A b L e D SIDE VIEW Package Drawing Contact: packagedrawings@atmel.com 8S1 G 6/22/11 Notes: This drawing is for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 8S1, 8-lead (0.150” Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) SWB

17Atmel AT24C16C [DATASHEET] Atmel-8719B-SEEPROM-AT24C16C-Datasheet_042013 13.2 8X — 8-lead TSSOP DRAWING NO. REV. TITLE GPC COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A - - 1.20 A1 0.05 - 0.15 A2 0.80 1.00 1.05 D 2.90 3.00 3.10 2, 5 E 6.40 BSC E1 4.30 4.40 4.50 3, 5 b 0.19 – 0.30 4 e 0.65 BSC L 0.45 0.60 0.75 L1 1.00 REF C 0.09 - 0.20 Side View End ViewTop View A L D N b Pin 1 indicator this corner E e Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15mm (0.006in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25mm (0.010in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07mm. 5. Dimension D and E1 to be determined at Datum Plane H. Package Drawing Contact: packagedrawings@atmel.com 8X D 6/22/11 8X, 8-lead 4.4mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) TNR C

18Atmel AT24C16C [DATASHEET] Atmel-8719B-SEEPROM-AT24C16C-Datasheet_042013 13.3 8MA2 — 8-pad UDFN TITLE DRAWING NO. GPC REV. Package Drawing Contact: packagedrawings@atmel.com 8MA2YNZ B 8MA2, 8-pad, 2 x 3 x 0.6 mm Body, Thermally Enhanced Plastic Ultra Thin Dual Flat No Lead Package (UDFN) COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 2.00 BSC E 3.00 BSC D2 1.40 1.50 1.60 E2 1.20 1.30 1.40 A 0.50 0.55 0.60 A1 0.0 0.02 0.05 A2 – – 0.55 C 0.152 REF L 0.30 0.35 0.40 e 0.50 BSC b 0.18 0.25 0.30 3 K 0.20 – – 7/15/11 E e (6x) L (8x) b (8x) Pin#1 ID A Pin 1 ID D C K

19Atmel AT24C16C [DATASHEET] Atmel-8719B-SEEPROM-AT24C16C-Datasheet_042013 13.4 8ME1 — 8-pad XDFN Package Drawing Contact: packagedrawings@atmel.com GPC DRAWING NO. REV. TITLE COMMON DIMENSIONS (Unit of Measure = mm) DTP SYMBOL MIN NOM MAX NOTE 0.00 1.70 2.10 0.15 0.26 A D E b e L 1.80 2.20 0.20

0.40 TYP

1.20 REF

0.30 0.40 0.05 1.90 2.30 0.25 0.35 End View 8ME1 B 9/10/2012 8ME1, 8-pad (1.80mm x 2.20mm body) Extra Thin DFN (XDFN) Top View 6 57 E D 1 2 PIN #1 ID 0.10 0.15 b L b e PIN #1 ID A Side View

20Atmel AT24C16C [DATASHEET] Atmel-8719B-SEEPROM-AT24C16C-Datasheet_042013 13.5 5TS1 — 5-lead SOT23 DRAWING NO. REV. TITLE GPC Package Drawing Contact: packagedrawings@atmel.com 5TS1 D 5/31/12 5TS1, 5-lead 1.60mm Body, Plastic Thin Shrink Small Outline Package (Shrink SOT) TSZ COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A - - 1.00 A1 0.00 - 0.10 A2 0.70 0.90 1.00 c 0.08 - 0.20 3 D 2.90 BSC 1,2 E 2.80 BSC 1,2 E1 1.60 BSC 1,2 L1 0.60 REF e 0.95 BSC e1 1.90 BSC b 0.30 - 0.50 3,4 1. Dimension D does not include mold flash, protrusions or gate burrs. Mold flash, protrusions or gate burrs shall not exceed 0.15 mm per end. Dimension E1 does not include interlead flash or protrusion. Interlead flash or protrusion shall not exceed 0.15 mm per side. 2. The package top may be smaller than the package bottom. Dimensions D and E1 are determined at the outermost extremes of the plastic body exclusive of mold flash, tie bar burrs, gate burrs and interlead flash, but including any mismatch between the top and bottom of the plastic body. 3. These dimensions apply to the flat section of the lead between 0.08 mm and 0.15 mm from the lead tip. 4. Dimension "b" does not include dambar protrusion. Allowable dambar protrusion shall be 0.08 mm total in excess of the "b" dimension at maximum material condition. The dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and an adjacent lead shall not be less than 0.07 mm. This drawing is for general information only. Refer to JEDEC Drawing MO-193, Variation AB for additional information. 5 4 L C END VIEW C AA2 b e PLANE SEATING D SIDE VIEW E TOP VIEW

21Atmel AT24C16C [DATASHEET] Atmel-8719B-SEEPROM-AT24C16C-Datasheet_042013 13.6 8U3-1 — 8-ball VFBGA DRAWING NO. REV. TITLE GPC Package Drawing Contact: packagedrawings@atmel.com 8U3-1 E 3/27/12 8U3-1, 8-ball, 1.50mm x 2.00mm body, 0.50mm pitch, VFBGA Package GXU COMMON DIMENSIONS (Unit of Measure - mm) SYMBOL MIN NOM MAX NOTE A 0.73 0.79 0.85 A1 0.09 0.14 0.19 A2 0.40 0.45 0.50 b 0.20 0.25 0.30 2 D 1.50 BSC E 2.0 BSC e 0.50 BSC e1 0.25 REF d 1.00 BSC d1 0.25 REF 1. This drawing is for general information only. 2. Dimension ‘b’ is measured at maximum solder ball diameter. Notes: SIDE VIEW A PIN 1 BALL PAD CORNER TOP VIEW E D b

8 SOLDER BALLS

(d1) d 432 (e1) e PIN 1 BALL PAD CORNER

22Atmel AT24C16C [DATASHEET] Atmel-8719B-SEEPROM-AT24C16C-Datasheet_042013 14. Revision History Doc. Rev. Date Comments 8719B 07/2013 Minor grammetical corrections. Update Atmel logos and template. 8719A 09/2010 Initial document release.

Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 | www.atmel.com © 2013 Atmel Corporation. All rights reserved. / Rev.: Atmel-8719B-SEEPROM-AT24C16C-Datasheet_042013. Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDIT IONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS P RODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMI TATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or c ompleteness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel d oes not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automo tive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical A pplications”) without an Atmel officer's specific written consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for t he operation of nuclear facilities and weapons systems. Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.