AT24C16B_09 ATMEL

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 27

Technical content

Mini-MAP (MLP 2x3) 8-lead PDIP5-lead SOT23 Bottom View Bottom View 8-lead TSSOP 1. Features

  • Low-voltage and Standard-voltage Operation – 1.8 (V CC = 1.8V to 5.5V)
  • Internally Organized 2048 x 8 (16K)
  • Two-wire Serial Interface
  • Schmitt Trigger, Filtered Inputs for Noise Suppression
  • Bidirectional Data Transfer Protocol
  • 1 MHz (5V, 2.5V), 400 kHz (1.8V) Compatibility
  • Write Protect Pin for Hardware Data Protection
  • 16-byte Page (16K) Write Modes
  • Partial Page Writes Allowed
  • Self-timed Write Cycle (5 ms max)
  • High-reliability – Endurance: 1 Million Write Cycles – Data Retention: 100 Years
  • 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead Ultra-Thin Mini-MAP (MLP 2x3), 5-lead SOT23, 8-lead Ultra Lead Frame Land Grid Array (ULA), 8-lead TSSOP and 8-ball dBGA2 Packages
  • Lead-free/Halogen-free
  • Die Sales: Wafer Form, Tape and Reel, and Bumped Wafers 2. Description The AT24C16B provides 16384 bits of serial electrically erasable and programmable read-only memory (EEPROM) organized as 2048 words of 8 bits each. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. The AT24C16B is available in space-saving 8-lead PDIP, 8-lead JEDEC SOIC, 8- lead Ultra Thin Mini-MAP (MLP 2x3) , 5-lead SOT23, 8-lead Ultra Lead Frame Land Grid Array (ULA), 8-lead TSSOP, and 8-ball dBGA2 packages and is accessed via a Two-wir e serial interface. In addition, the AT24C16B is available in 1.8V (1.8V to 5.5V) version. Table 2-1. Pin Configuration Pin Name Function NC No Connect SDA Serial Data SCL Serial Clock Input WP Write Protect GND Ground VCC Power Supply Two-wire Serial EEPROM 16K (2048 x 8) AT24C16B 5175E–SEEPR–3/09 VCC WP SCL SDA NC NC NC GND 8-lead Ultra Lead Frame Land Grid Array (ULA) Bottom View

5175E–SEEPR–3/09 AT24C16B Figure 2-1. Block Diagram Absolute Maximum Ratings Maximum Ratings” may cause permanent dam- age to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Voltage on Any Pin START STOP LOGIC VCC GND WP SCL SDA SERIAL CONTROL LOGIC EN H.V. PUMP/TIMING EEPROM DATA RECOVERY SERIAL MUX X DEC DOUT/ACK LOGIC COMP LOAD INC DATA WORD ADDR/COUNTER Y DEC R/W DOUT DIN LOAD DEVICE ADDRESS COMPARATOR

5175E–SEEPR–3/09 AT24C16B 3. Pin Description SERIAL CLOCK (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative edge clock data out of each device. SERIAL DATA (SDA): The SDA pin is bidirectional for seri al data transfer. This pin is open- drain driven and may be wire-ORed with any number of other open-drain or open-collector devices. DEVICE/PAGE ADDRESSES: The AT24C16B does not use the device address pins, which lim- its the number of devices on a single bus to one. WRITE PROTECT (WP): The AT24C16B has a write protect pin that provides hardware data protection. The write protect pin allows normal re ad/write operations when connected to ground (GND). When the write prot ect pin is connected to V CC, the write protecti on feature is enabled and operates as shown in Table 3-1. Table 3-1. Write Protect 4. Memory Organization AT24C16B, 16K SERIAL EEPROM: Internally organized with 128 pages of 16 bytes each, the 16K requires an 11-bit data word address for random word addressing. WP Pin Status Part of the Array Protected 24C16B At VCC Full (16K) Array At GND Normal Read/Write Operations

5175E–SEEPR–3/09 AT24C16B Note: 1. This parameter is characterized and is not 100% tested. Notes: 1. V IL min and VIH max are reference only and are not tested. Table 4-1. Pin Capacitance(1) Applicable over recommended operating range from TA = 25°C, f = 1.0 MHz, VCC = +1.8V Symbol Test Condition Max Units Conditions CI/O Input/Output Capacitance (SDA) 8 pF V I/O = 0V CIN Input Capacitance (SCL) 6 pF V IN = 0V Table 4-2. DC Characteristics Applicable over recommended operating range from: TAI = −40°C to +85°C, VCC = +1.8V to +5.5V (unless otherwise noted) Symbol Parameter Test Co ndition Min Typ Max Units VCC1 Supply Voltage 1.8 5.5 V ICC1 Supply Current V CC = 5.0V READ at 400 kHz 1.0 2.0 mA ICC2 Supply Current V CC = 5.0V WRITE at 400 kHz 2.0 3.0 mA ISB1 Standby Current (1.8V option) VCC = 1.8V VIN = VCC or VSS 1.0 µA VCC = 5.5V 6.0 ILI Input Leakage Current VCC = 5.0V VIN = VCC or VSS 0.10 3.0 µA ILO Output Leakage Current VCC = 5.0V VOUT = VCC or VSS 0.05 3.0 µA VIL Input Low Level(1) −0.6 V CC x 0.3 V VIH Input High Level(1) VCC x 0.7 V CC + 0.5 V VOL1 Output Low Level V CC = 1.8V I OL = 0.15 mA 0.2 V VOL2 Output Low Level V CC = 3.0V I OL = 2.1 mA 0.4 V

5175E–SEEPR–3/09 AT24C16B Notes: 1. This parameter is characterized and is not 100% tested. 2. AC measurement conditions: RL (connects to VCC): 1.3 kΩ (2.5V, 5.0V), 10 kΩ (1.8V) Input pulse voltages: 0.3 VCC to 0.7 VCC Input rise and fall times: ≤ 50 ns Input and output timing reference voltages: 0.5 VCC Table 4-3. AC Characteristics (Industrial Temperature) Applicable over recommended operating range from TAI = −40°C to +85°C, VCC = +1.8V to +5.5V, CL = 100 pF (unless oth- erwise noted). Test conditions are listed in Note 2. Symbol Parameter 1.8-volt 2.5, 5.0-volt UnitsMin Max Min Max fSCL Clock Frequency, SCL 400 1000 kHz tLOW Clock Pulse Width Low 1.3 0.4 µs tHIGH Clock Pulse Width High 0.6 0.4 µs tAA Clock Low to Data Out Valid 0.05 0.9 0.05 0.55 µs tBUF Time the bus must be free before a new transmission can start(1) 1.3 0.5 µs tHD.STA Start Hold Time 0.6 0.25 µs tSU.STA Start Set-up Time 0.6 0.25 µs tHD.DAT Data In Hold Time 0 0 µs tSU.DAT Data In Set-up Time 100 100 ns tR Inputs Rise Time(1) 0.3 0.3 µs tF Inputs Fall Time(1) 300 100 ns tSU.STO Stop Set-up Time 0.6 0.25 µs tDH Data Out Hold Time 50 50 ns tWR Write Cycle Time 5 5 ms Endurance(1) 25°C, Page Mode, 3.3V 1,000,000 Write Cycles

5175E–SEEPR–3/09 AT24C16B 5. Device Operation CLOCK and DATA TRANSITIONS: The SDA pin is normally pulled high with an external device. Data on the SDA pin may change only during SCL low time periods (see Figure 7-2 on page 8). Data changes during SCL high periods will indicate a start or stop condition as defined below. START CONDITION: A high-to-low transition of SDA with SCL high is a start condition which must precede any other command (see Figure 7-3 on page 8). STOP CONDITION: A low-to-high transition of SDA with SCL high is a stop condition. After a read sequence, the stop command will place the EEPROM in a standby power mode (see Fig- ure 7-3 on page 8). ACKNOWLEDGE: All addresses and data words are serially transmitted to and from the EEPROM in 8-bit words. The EEPROM sends a ze ro to acknowledge that it has received each word. This happens during the ninth clock cycle. STANDBY MODE: The AT24C16B features a low-power standby mode which is enabled: (a) upon power-up and (b) after the receipt of the STOP bit and the completion of any internal operations. 2-WIRE SOFTWARE RESET: After an interruption in protocol, power loss or system reset, any 2-wire part can be protocol reset by following these steps: 1. Create a start bit condition. 2. Clock 9 cycles. 3. Create another start bit followed by stop bit condition as shown below. Start bit Stop bitStart bitDummy Clock Cycles SCL SDA 123 89

5175E–SEEPR–3/09 AT24C16B 8. Device Addressing The 16K EEPROM device requires an 8-bit device address word following a start condition to enable the chip for a read or write operation (refer to Figure 10-1). The device address word consists of a mandatory one, zero sequence for the first four most sig- nificant bits as shown. This is common to all the EEPROM devices. The next 3 bits used for memory page addressing and are the most significant bits of the data word address which follows. The eighth bit of the device address is the read/write operation select bit. A read operation is ini- tiated if this bit is high and a write operation is initiated if this bit is low. Upon a compare of the device address, the EEPROM will outpu t a zero. If a compare is not made, the chip will return to a standby state. 9. Write Operations BYTE WRITE: A write operation requires an 8-bit dat a word address following the device address word and acknowledgment. Upon receipt of this address, the EEPROM will again respond with a zero and then clock in the first 8-bit data word. Following receipt of the 8-bit data word, the EEPROM will output a ze ro and the addr essing device, such as a microcontroller, must terminate the writ e sequence with a stop condition. At this time the EEPROM enters an internally timed write cycle, t WR, to the nonvolatile memory. All inputs are disabled during this write cycle and the EEPROM will not resp ond until the write is complete (see Figure 10-2 on page 11). PAGE WRITE: The 16K EEPROM is capable of an 16-byte page write. A page write is initiated the same as a byte write, but the microcontroller does not send a stop condition after the first data word is clocked in. Instead, after the EEPROM acknowledges receipt of the first data word, the microcontrolle r can transmit up to fifteen data words. The EEPROM will respond with a zero after each data word received. The microcontroller must ter- minate the page write sequence with a stop condition (see Figure 10-3 on page 11). The data word address lower three bits are inter nally incremented following the receipt of each data word. The higher data word address bits are not incremented, retaining the memory page row location. When the word address, internally generated, reaches the page boundary, the fol- lowing byte is placed at the beginning of the same page. If more than sixteen data words are transmitted to the EEPROM, the data word a ddress will “roll over” and previous data will be overwritten. ACKNOWLEDGE POLLING: Once the internally timed wr ite cycle has st arted and the EEPROM inputs are disabled, ackno wledge polling can be initiate d. This involves sending a start condition followed by the device address wo rd. The read/write bit is representative of the operation desired. Only if th e internal write cycle has comp leted will the EEPROM respond with a zero allowing the read or write sequence to continue.

5175E–SEEPR–3/09 AT24C16B 10. Read Operations Read operations are initiated the same way as write operations with the exception that the read/write select bit in the device address word is set to one. There are three read operations: current address read, random address read and sequential read. CURRENT ADDRESS READ: The internal data word address counter maintains the last address accessed during the last read or write operation, incremented by one. This address stays valid between operations as long as the ch ip power is maintained. The address “roll over” during read is from the last byte of the last me mory page to the first byte of the first page. The address “roll over” during write is from the last byte of the current page to the first byte of the same page. Once the device address with the read/write select bit set to one is clocked in and acknowledged by the EEPROM, the current address data word is serially clocked out. The microcontroller does not respond with an input zero but does generate a following stop condition (see Figure 10-4 on page 11). RANDOM READ: A random read requires a “dummy” byte write sequence to load in the data word address. Once the device address word and data word address are clocked in and acknowledged by the EEPROM, the microcontrolle r must generate another start condition. The microcontroller now initiates a current address read by sending a device address with the read/write select bit high. The EEPROM acknowl edges the device address and serially clocks out the data word. The microcontroller does not respond with a zero but does generate a follow- ing stop condition (see Figure 10-5 on page 12). SEQUENTIAL READ: Sequential reads are initiated by either a current address read or a ran- dom address read. After the microcontroller receives a data word, it responds with an acknowledge. As long as the EEPROM receives an acknowledge, it will continue to increment the data word address and serially clock out sequential data words. When the memory address limit is reached, the data word address will “roll over” and the sequential read will continue. The sequential read operation is terminated when the microcontroller does not respond with a zero but does generate a following stop condition (see Figure 10-6 on page 12). Figure 10-1. Device Address MSB PPP2 10

5175E–SEEPR–3/09 AT24C16B Notes: 1. “-B” denotes bulk. 2. “-T” denotes tape and reel. SOIC = 4K per reel. TSSOP, Ultra Thin Mini MAP , SOT23, dBGA2 = 5K per reel. 3. Available in tape and reel, and wafer form; order as SL788 for inkless wafer form. Bumped die available upon request. Please contact Serial Interface Marketing. Ordering Codes Voltage Package Operating Range AT24C16B-PU (Bulk Form Only) 1.8 8P3 Lead-Free/Halogen-Free Industrial Temperature (-40°C to 85°C) AT24C16BN-SH-B(1) (NiPdAu Lead Finish) 1.8 8S1 AT24C16BN-SH-T(2) (NiPdAu Lead Finish) 1.8 8S1 AT24C16B-TH-B(1) (NiPdAu Lead Finish) 1.8 8A2 AT24C16B-TH-T(2) (NiPdAu Lead Finish) 1.8 8A2 AT24C16BY6-YH-T(2) (NiPdAu Lead Finish) 1.8 8Y6 AT24C16BD3-DH-T(2) (NiPdAu Lead Finish) 1.8 8D3 AT24C16BTSU-T(2) 1.8 5TS1 AT24C16BU3-UU-T(2) 1.8 8U3-1 AT24C16B-W-11(3) 1.8 Die Sales Industrial Temperature (-40°C to 85°C) Package Type 8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) 8Y6 8-lead, 2.0 mm x 3.00 mm Body, 0.50 mm Pitch, Ultra Thin Mini-MAP, Dual No Lead Package (DFN), (MLP 2x3 mm) 5TS1 5-lead, 2.90 mm x 1.60 mm Body, Plastic Thin Shrink Small Outline Package (SOT23) 8U3-1 8-ball, die Ball Grid Array Package (dBGA2) 8D3 8-lead, 1.80 mm x 2.20 mm Body, Ultra Lead Frame Land Grid Array (ULA) Options –1.8 Low-voltage (1.8V to 5.5V)

5175E–SEEPR–3/09 AT24C16B 11. Part Marking 11.1 8-PDIP Seal Year TOP MARK | Seal Week | | | A T M L U Y W W 1 6 B 1 * Lot Number Pin 1 Indicator (Dot) Y = SEAL YEAR WW = SEAL WEEK 6: 2006 0: 2010 02 = Week 2 7: 2007 1: 2011 04 = Week 4 50 = Week 50 52 = Week 52 Lot Number to Use ALL Characters in Marking BOTTOM MARK No Bottom Mark

5175E–SEEPR–3/09 AT24C16B 11.2 8-SOIC Seal Year TOP MARK | Seal Week | | | A T M L H Y W W 1 6 B 1 * Lot Number Pin 1 Indicator (Dot) Y = SEAL YEAR WW = SEAL WEEK 6: 2006 0: 2010 02 = Week 2 7: 2007 1: 2011 04 = Week 4 50 = Week 50 52 = Week 52 Lot Number to Use ALL Characters in Marking BOTTOM MARK No Bottom Mark

5175E–SEEPR–3/09 AT24C16B 11.3 8-TSSOP TOP MARK Pin 1 Indicator (Dot) * H Y W W 1 6 B 1 BOTTOM MARK P H A A A A A A A <- Pin 1 Indicator Y = SEAL YEAR WW = SEAL WEEK 6: 2006 0: 2010 02 = Week 2 7: 2007 1: 2011 04 = Week 4 50 = Week 50 52 = Week 52

5175E–SEEPR–3/09 AT24C16B 11.4 8-Ultra Thin Mini-Map 11.5 8-ULA TOP MARK |---|---|---| 1 6 B |---|---|---| Y X X |---|---|---| Pin 1 Indicator (Dot) Y = BUILD YEAR 2006 = 6 2008 = 8 2007 = 7 Etc. . . XX = ATMEL LOT NUMBER TO COORESPOND WITH NSEB TRACE CODE LOG BOOK. TOP MARK |---|---|---| 1 6 B |---|---|---| H 1 |---|---|---| Y X X |---|---|---| Pin 1 Indicator (Dot) Y = YEAR OF ASSEMBLY XX = ATMEL LOT NUMBER TO COORESPOND WITH NSEB TRACE CODE LOG BOOK. Y = SEAL YEAR 6: 2006 0: 2010 7: 2007 1: 2011 8: 2008 2: 2012 9: 2009 3: 2013

5175E–SEEPR–3/09 AT24C16B 11.6 dBGA2 TOP MARK |<-- Pin 1 This Corner P = COUNTRY OF ORIGIN Y = ONE DIGIT YEAR CODE 4: 2004 7: 2007 5: 2005 8: 2008 6: 2006 9: 2009 M = SEAL MONTH (USE ALPHA DESIGNATOR A-L) A = JANUARY B = FEBRUARY J = OCTOBER K = NOVEMBER L = DECEMBER TC = TRACE CODE (ATMEL LOT NUMBERS TO CORRESPOND WITH ATK TRACE CODE LOG BOOK)

11.7 SOT23

XXX = Device V = Voltage Indicator U = Material Set Pin 1 Indicator (Dot) BOTTOM MARK Y M T C Y = One Digit Year Code M = Seal Month (Use Alpha Designator A-L) TC = Trace Code

5175E–SEEPR–3/09 AT24C16B 12. Packaging Information 12.1 8P3 – PDIP

2325 Orchard Parkway

San Jose, CA 95131 TITLE DRAWING NO. R REV. 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) 01/09/02 8P3 B Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA, for additional information . 2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion. COMMON DIMENSIONS (Unit of Measure = inches) SYMBOL MIN NOM MAX NOTE D E e Lb2 b A2 A N eA c

4 PLCS

A – – 0.210 2 A2 0.115 0.130 0.195 b 0.014 0.018 0.022 5 b2 0.045 0.060 0.070 6 b3 0.030 0.039 0.045 6 c 0.008 0.010 0.014 D 0.355 0.365 0.400 3 D1 0.005 – – 3 E 0.300 0.310 0.325 4 E1 0.240 0.250 0.280 3 e 0.100 BSC eA 0.300 BSC 4 L 0.115 0.130 0.150 2 Top View Side View End View

5175E–SEEPR–3/09 AT24C16B 12.2 8S1 – JEDEC SOIC 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. Note: 10/7/03 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) 8S1 B COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. A 1.35 – 1.75 b 0.31 – 0.51 C 0.17 – 0.25 D 4.80 – 5.00 E1 3.81 – 3.99 E 5.79 – 6.20 e 1.27 BSC L 0.40 – 1.27 ∅ 0˚ – 8˚ Top View End View Side View e B D A N E C L

5175E–SEEPR–3/09 AT24C16B 12.3 8A2 – TSSOP San Jose, CA 95131 TITLE DRAWING NO. R REV. 5/30/02 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 2.90 3.00 3.10 2, 5 E 6.40 B SC E1 4. 30 4.40 4.50 3, 5 A – – 1.20 A2 0. 80 1.00 1.05 b 0.19 – 0. 304 e 0.65 B SC L 0.45 0.60 0.75 L1 1.00 REF 8A2, 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Notes: 1. Thi s drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimen sion D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimen sion E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimen sion b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimen sion D and E1 to be determined at Datum Plane H. 8A2 B Side View End ViewTop View A L D 123 N b Pin 1 indicator this corner E e

5175E–SEEPR–3/09 AT24C16B 12.4 8Y6 - Mini Map San Jose, CA 95131 TITLE DRAWING NO. R REV. 8Y6, 8-lead 2.0 x 3.0 mm Body, 0.50 mm Pitch, Utlra Thin Mini-Map, Dual No Lead Package (DFN) ,(MLP 2x3) D8Y6 10/16/07 Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-229, for proper dimensions, tolerances, datums, etc. 2. Dimension b applies to metallized terminal and is measured between 0.15 mm and 0.30 mm from the terminal tip. If the terminal has the optional radius on the other end of the terminal, the dimension should not be measured in that radius area. 3. Soldering the large thermal pad is optional, but not recommended. No electrical connection is accomplished to the device through this pad, so if soldered it should be tied to ground COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 2.00 BSC E 3.00 BSC D2 1.40 1.50 1.60 E2 - - 1.40 A - - 0.60 A1 0.0 0.02 0.05 A2 - - 0.55 A3 0.20 REF L 0.20 0.30 0.40 e 0.50 BSC b 0.20 0.25 0.30 2 A2A2 b (8X)(8X) Pin 1 IDPin 1 ID Pin 1Pin 1 IndexIndex AreaArea A1A1 A3A3 D E A L (8X)L (8X) e (6X)e (6X) 1.50 REF.1.50 REF. D2D2 E2E2

5175E–SEEPR–3/09 AT24C16B 12.5 5TS1 – SOT23 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. PO5TS1 A 6/25/03 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE 5TS1, 5-lead, 1.60 mm Body, Plastic Thin Shrink Small Outline Package (SHRINK SOT) A – – 1.10 A1 0.00 – 0.10 A2 0.70 0.90 1.00 c 0.08 – 0.20 4 D 2.90 BSC 2, 3 E 2.80 BSC 2, 3 E1 1.60 BSC 2, 3 L1 0.60 REF e 0.95 BSC e1 1.90 BSC b 0.30 – 0.50 4, 5 NOTES: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-193, Variation AB, for additional information. 2. Dimension D does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed 0.15 mm per end. Dimension E1 does not include interlead flash or protrusion. Interlead flash or protrusion shall not exceed 0.15 mm per side. 3. The package top may be smaller than the package bottom. Dimensions D and E1 are determined at the outermost extremes of the plastic body exclusive of mold flash, tie bar burrs, gate burrs, and interlead flash, but including any mismatch between the top and bottom of the plastic body. 4. These dimensions apply to the flat section of the lead between 0.08 mm and 0.15 mm from the lead tip. 5. Dimension "b" does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the "b" dimension at maximum material condition. The Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and an adjacent lead shall not be less than 0.07 mm. 5 4 L C End View C AA2 b e Seating Plane D Side View Top View E

5175E–SEEPR–3/09 AT24C16B 12.6 8U3-1 – dBGA2 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. PO8U3-1 A 6/24/03 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE 8U3-1, 8-ball, 1.50 x 2.00 mm Body, 0.50 mm pitch, Small Die Ball Grid Array Package (dBGA2) A 0.71 0.81 0.91 A1 0.10 0.15 0.20 A2 0.40 0.45 0.50 b 0.20 0.25 0.30 D 1.50 BSC E 2.00 BSC e 0.50 BSC e1 0.25 REF d 1.00 BSC d1 0.25 REF 1. Dimension “b” is measured at the maximum solder ball diameter. This drawing is for general information only. Bottom View

8 SOLDER BALLS

E Top View PIN 1 BALL PAD CORNER A Side View PIN 1 BALL PAD CORNER e 678 d (e1) (d1)

5175E–SEEPR–3/09 AT24C16B 12.7 8D3 - ULA 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. 8D3, 8-lead (1.80 x 2.20 mm Body) Ultra Leadframe Land Grid Array (ULLGA) D3 08D3 11/15/05 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A – – 0.40 A1 0.00 – 0.05 D 1.70 1.80 1.90 E 2.10 2.20 2.30 b 0.15 0.20 0.25 e 0.40 TYP e1 1.20 REF L 0.25 0.30 0.35 0.10 0.15 b 6 57 E D 1 2 PIN #1 ID TOP VIEW L b A e PIN #1 ID SIDE VIEW BOTTOM VIEW

5175E–SEEPR–3/09 AT24C16B 13. Revision History Lit No. Date Comment 5175E 3/2009 Changed the Vcc to 5.5V in the test condition for Isb1 5175D 6/2008 Deleted A0, A1, A2 pin-outs 5175C 11/2007 AT24C16B product with date code 742 or later supports 5Vcc operation Added ULA package information 5175B 4/2007 Removed reference to Waffle Pack Corrected Note 3 on Page 13 Added lines to Ordering Code table 5175A 3/2007 Initial document release

5175E–SEEPR–3/09 Headquarters International Atmel Corporation San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Room 1219 Chinachem Golden Plaza

77 Mody Road Tsimshatsui

Tel: (852) 2721-9778 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309

78054 Saint-Quentin-en-

9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Product Contact Web Site www.atmel.com Technical Support s_eeprom@atmel.com Sales Contact www.atmel.com/contacts Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection wi th Atmel products. No license, expr ess or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LI ABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTOR Y WARRANTY RELATING TO ITS PRODUCTS INCLUDING , BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICU LAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRE CT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR I NCIDEN- TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or comp leteness of the contents of th is document and reserves the rig ht to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained her ein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not int ended, authorized, or warranted for use as components in applications intended to support or sustain life. ©2009 Atmel Corporation. All rights reserved. Atmel ®, Atmel logo and combinations thereof and others, are registered trademarks or trade- marks of Atmel Corporation or its subsidiaries. Ot her terms and product names may be trademarks of others.